sm6150-common: configs: Update wcnss config from sm8150

Signed-off-by: Pranav Vashi <neobuddy89@gmail.com>
Signed-off-by: donjohanliebert <donjohanliebert@gmail.com>

configs/wifi/WCNSS_qcom_cfg.ini

@@ -59,9 +59,9 @@ gFixedRate=0
 # gFragmentationThreshold=2346
 
 # RTS threshold
-RTSThreshold=1048576
+RTSThreshold=2346
 
-# RTSCTS_ENABLED_4_SWRETRIES
+# CTS2SELF_ENABLED_4_SWRETRIES
 gEnableRTSProfiles=33
 
 # Intra-BSS forward
@@ -461,9 +461,13 @@ ce_service_max_rx_ind_flush=1
 maxMSDUsPerRxInd=8
 
 # Enable NUD tracking feature
-# 0 - disable(default),1 - trigger disconnect, 2 - trigger roaming,
+# 1 - enable 0 - disable(default) 3 - Driver will try to roam to a new AP but if roam fails, disconnect.
-# 3 - trigger roaming, but if roam fails, disconnection
 gEnableNUDTracking=3
+
+# Enable PEER UNMAP CONF SUPPORT
+# 1 - enable 0 - disable(default)
+gEnablePeerUnmapConfSupport=1
+
 ################ Datapath feature set End ################
 
 ################ NAN feature set start ###################
@@ -490,9 +494,21 @@ adapt_dwell_wifi_act_threshold=10
 # Enable pkt log
 # 1 - enable, 0 - disable
 gEnablePacketLog=1
+
+# Force 1x1 for 2.4g SAP, P2P-GC/GO, 2x2 for STA
+# gVdevTypeNss_2g=21846
+
 # 0: Disable BPF packet filter
 # 1: Enable BPF packet filter
 gBpfFilterEnable=1
+
+gActiveUcBpfMode=1
+gActiveMcBcBpfMode=1
+
+# 0: Disable force 1x1 on MTK solution AP
+# 1: Enable force 1x1 on MTK solution AP
+gForce1x1Exception=0
+
 # set modulated DTIM interval
 gEnableModulatedDTIM=3
 gMaxLIModulatedDTIM=3
@@ -523,11 +539,15 @@ gper_roam_enabled=3
 # WME_AC_VI = 2 (Video)
 # WME_AC_VO = 3 (Voice)
 arp_ac_category=0
-
 # Enable/Disable DTIM Synth
 # 1- Enable DTIM Synth
 # 0- Disable DTIM Synth
 gEnableLPRx=0
+
+#############################################
+# MAWC related configurations
+#############################################
+
 # MAWCEnabled - Enable/Disable Motion Aided Wireless Connectivity Global
 MAWCEnabled=0
 
@@ -568,12 +588,9 @@ drop_bcn_on_chan_mismatch=0
 enable_rtt_mac_randomization=1
 
 # Create another interface during driver load
-#gEnableConcurrentSTA=wlan1
+gEnableConcurrentSTA=wlan1
 
-# Enable/Disable DBS
+#Enable/Disable SNR monitoring
-gDualMacFeatureDisable=0
-
-# Enable/Disable SNR monitoring
 gEnableSNRMonitoring=1
 
 # WLM latency Enable
@@ -582,33 +599,42 @@ wlm_latency_enable=1
 # WLM flags setting for ultralow level, bit9 for BMPS disabled
 wlm_latency_flags_ultralow=0xe03
 
-# Enable ETSI SRD channels by Xiaomi. Qualcom default value is disable
+#Enable ETSI SRD channels by Xiaomi. Qualcom default value is disable
 etsi13_srd_chan_in_master_mode=1
 
 #Configures Channel Bonding in 24 GHz
-gChannelBondingMode24GHz=1
+gChannelBondingMode24GHz=0
-
-
-# Disable wpa3 on 7150 device
-sae_enabled=1
-
-gActiveUcBpfMode=1
-gActiveMcBcBpfMode=1
 
 # Allow STA+SAP SCC on DFS channel with master mode support disabled
-g_sta_sap_scc_on_dfs_chan=2
+g_sta_sap_scc_on_dfs_chan=1
 
-gStaPrefer80MHzOver160MHz=1
+# Enable wpa3 on 8150 device
+sae_enabled=1
+
+# Set IPA low/med/high bandwidth mbps
+gIPALowBandwidthMbps=100
+gIPAMediumBandwidthMbps=400
+gIPAHighBandwidthMbps=800
+
+# Enable/Disable force bandwidth voting during IPA suspend
+gIPAForceVotingEnable=1
+spectral_disable=1
 
 gEnableSARV1toSARV2=1
 
-np_chan_weight=0x1
+gStaPrefer80MHzOver160MHz=1
 
 # Reduce the expiry time for avoid list and black list in drv.
 avoid_list_expiry_time=3
 black_list_expiry_time=3
 # Improve threshold to move the Ap from avoid to blacklist
 bad_bssid_counter_thresh=7
+
+# Enable SoftAP on indoor channel, but Xiaomi's patch in driver only
+# allow this when STA was connected on the same indoor channel.
+gindoor_channel_support=1
+
 END
 
 # Note: Configuration parser would not read anything past the END marker
+