LimeSDR: updated documentation

Readme.md

@@ -41,7 +41,7 @@ From version 3 transmission or signal generation is supported for BladeRF, HackR
 
   - [BladeRF output plugin](https://github.com/f4exb/sdrangel/tree/dev/plugins/samplesink/bladerfoutput) limited support in Windows
   - [HackRF output plugin](https://github.com/f4exb/sdrangel/tree/dev/plugins/samplesink/hackrfoutput)
-  - [LimeSDR output plugin](https://github.com/f4exb/sdrangel/tree/dev/plugins/samplesink/limesdroutput) not working properly
+  - [LimeSDR output plugin](https://github.com/f4exb/sdrangel/tree/dev/plugins/samplesink/limesdroutput)
   - [PlutoSDR output plugin](https://github.com/f4exb/sdrangel/tree/dev/plugins/samplesink/plutosdroutput)
   - [File output or file sink plugin](https://github.com/f4exb/sdrangel/tree/dev/plugins/samplesink/filesink)
   - [Remote device via Network with SDRdaemon](https://github.com/f4exb/sdrangel/tree/dev/plugins/samplesink/sdrdaemonsink) Linux only
@@ -119,11 +119,9 @@ HackRF is better used with a sampling rate of 4.8 MS/s and above. The 2.4 and 3.
 
 [LimeSDR](https://myriadrf.org/projects/limesdr/) and its smaller clone LimeSDR Mini are supported using LimeSuite library (see next).
 
-<p><b>&#9888; The latest version of LimeSuite is used and must be considered experimental. For now only the Rx side is operational.</b></p>
+<p>&#9888; Version 18.04.1 of LimeSuite is used in the builds and corresponding gateware loaded in the LimeSDR should be is used (2.16 for LimeSDR-USB and 1.24 for LimeSDR-Mini). If you compile from source version 18.04.1 of LimeSuite must be used.</p>
 
-<p>&#9888; It seems LimeSDR mini has trouble working with host sample rates lower than 2.5 MS/s particularly in Tx mode.</p>
-
-You will need a minimal installation of LimeSuite. Presently commit 90c3991 or later should be used with its corresponding firmware (v4) and gateware (v2.14) installed in the LimeSDR device. LimeSDR Mini gateware v1.24 should be used.
+<p>&#9888; LimeSDR-Mini seems to have problems with Zadig driver therefore it is supported in Linux only.</p>
 
   - `sudo apt-get install libsqlite3-dev`
   - `git clone https://github.com/myriadrf/LimeSuite.git`

debian/changelog

@@ -1,6 +1,6 @@
 sdrangel (3.14.3-1) unstable; urgency=medium
 
-  * LimeSDR: compiled with LimeSuite commit 67dcef1
+  * LimeSDR: compiled with LimeSuite release 18.04.1
   * LimeSDR: implemented transverter dialog (issue #157)
   * UDP source and sink: make sure audio samples are always on 16 bits
   * UDP source and sink: dialog elements for address and port

plugins/samplesink/limesdroutput/readme.md

@@ -4,7 +4,9 @@
 
 This output sample sink plugin sends its samples to a [LimeSDR device](https://myriadrf.org/projects/limesdr/).
 
-<p><b>&#9888; The latest version of LimeSuite is used and must be considered experimental. Hence LimeSDR support in SDRangel is also experimental. Tx does not work properly now.</b></p>
+<p>&#9888; Version 18.04.1 of LimeSuite is used in the buildsand corresponding gateware loaded in the LimeSDR should be is used (2.16 for LimeSDR-USB and 1.24 for LimeSDR-Mini). If you compile from source version 18.04.1 of LimeSuite must be used.</p>
+
+<p>&#9888; LimeSDR-Mini seems to have problems with Zadig driver therefore it is supported in Linux only.</p>
 
 LimeSDR is a 2x2 MIMO device so it has two transmitting channels that can run concurrently. To activate the second channel when the first is already active just open a new sink tab in the main window (Devices -> Add sink device) and select the same LimeSDR device.
 

plugins/samplesource/limesdrinput/readme.md

@@ -4,6 +4,10 @@
 
 This input sample source plugin gets its samples from a [LimeSDR device](https://myriadrf.org/projects/limesdr/).
 
+<p>&#9888; Version 18.04.1 of LimeSuite is used in the builds and corresponding gateware loaded in the LimeSDR should be is used (2.16 for LimeSDR-USB and 1.24 for LimeSDR-Mini). If you compile from source version 18.04.1 of LimeSuite must be used.</p>
+
+<p>&#9888; LimeSDR-Mini seems to have problems with Zadig driver therefore it is supported in Linux only.</p>
+
 LimeSDR is a 2x2 MIMO device so it has two receiving channels that can run concurrently. To activate the second channel when the first is already active just open a new source tab in the main window (Devices -> Add source device) and select the same LimeSDR device.
 
 <h2>Build</h2>