Pager demodulator plugin
Introduction
This plugin can be used to demodulate POCSAG pager messages.
Interface
1: Frequency shift from center frequency of reception
Use the wheels to adjust the frequency shift in Hz from the center frequency of reception. Left click on a digit sets the cursor position at this digit. Right click on a digit sets all digits on the right to zero. This effectively floors value at the digit position. Wheels are moved with the mousewheel while pointing at the wheel or by selecting the wheel with the left mouse click and using the keyboard arrows. Pressing shift simultaneously moves digit by 5 and pressing control moves it by 2.
2: Channel power
Average total power in dB relative to a +/- 1.0 amplitude signal received in the pass band.
3: Level meter in dB
- top bar (green): average value
- bottom bar (blue green): instantaneous peak value
- tip vertical bar (bright green): peak hold value
4: BW - RF Bandwidth
This specifies the bandwidth of a LPF that is applied to the input signal to limit the RF bandwidth.
5: Dev - Frequency deviation
Adjusts the expected frequency deviation in 0.1 kHz steps from 1 to 6 kHz. POCSAG uses FSK with a +/- 4.5 kHz shift.
6: Mod - Modulation
Specifies the pager modulation. Currently only POCSAG is supported.
POCSAG uses FSK with 4.5kHz frequency shift, at 512, 1200 or 2400 baud.
High frequency is typically 0, with low 1, but occasionally this appears to be reversed, so the demodulator supports either.
Data is framed as specified in ITU-R M.584-2: https://www.itu.int/dms_pubrec/itu-r/rec/m/R-REC-M.584-2-199711-I!!PDF-E.pdf
7: Baud
Specifies the baud rate. For POCSAG, this can be 512, 1200 or 2400.
8: Decode
Specifies how messages are decoded in the Message column in the table:
* Standard - As per ITU-R M.584-2 - Function 0 = numeric, function 1-3 = alphanumeric.
* Inverted - Function 3 = numeric, function 0-2 = alphanumeric.
* Numeric - Always decode as numeric.
* Alphanumeric - Always decode as alphanumeric.
* Heuristic - The plugin will try to guess based on the content of the message.
The table has Numeric and Alphanumeric columns which always display the corresponding decode.
9: Find
Entering a regular expression in the Find field displays only messages where the address matches the given regular expression.
10: Clear Messages from table
Pressing this button clears all messages from the table.
11: UDP
When checked, received messages are forwarded to the specified UDP address (12) and port (13).
The messages are forwarded as null terminated ASCII strings, in the format: data time address function alpha numeric
12: UDP address
IP address of the host to forward received messages to via UDP.
13: UDP port
UDP port number to forward received messages to.
Received Messages Table
The received messages table displays each pager message received.
* Date - The date the message was received.
* Time - The time the message was received.
* Address - The 21-bit pager address the message is for.
* Message - The decoded message, as per Decode setting (8). This will be empty for "tone only" messages (i.e. when the pager beeps without a message).
* Function - Function bits. In some instances this is used to specify the encoding of the message (Numeric/alphanumeric). In others, it is the pager source address.
* Alpha - Message decoded as alphanumeric text, regardless of Decode setting (8)
* Numeric - Message decoded as numeric, regardless of Decode setting (8).
* Even PE - Number of even parity errors detected in the code words of the message.
* BCH PE - Number of uncorrectable BCH parity errors detected in the code words of the message.
Right clicking on the table header allows you to select which columns to show. The columns can be reordered by left clicking and dragging the column header. Right clicking on an item in the table allows you to copy the value to the clipboard.