1
0
mirror of https://github.com/f4exb/sdrangel.git synced 2024-11-23 00:18:37 -05:00
sdrangel/plugins/samplesource/hackrfinput
2017-05-26 17:43:58 +02:00
..
CMakeLists.txt HackRF Output support: created a HackRF device library for Rx/Tx common routines and structures 2017-01-07 11:24:09 +01:00
hackrfinput.cpp HackRF: fixed bandwidth selection 2017-05-26 17:42:57 +02:00
hackrfinput.h HackRF input: force settings at start and on preset deserialization 2017-05-26 17:43:58 +02:00
hackrfinput.pro MacOS(sierra) development environment. 2017-05-15 12:32:16 +02:00
hackrfinputgui.cpp HackRF input: force settings at start and on preset deserialization 2017-05-26 17:43:58 +02:00
hackrfinputgui.h HackRF input: force settings at start and on preset deserialization 2017-05-26 17:43:58 +02:00
hackrfinputgui.ui updated value dials with Windows compatible font and pointing hand 2017-05-16 22:35:44 +02:00
hackrfinputplugin.cpp activated compiler warnings 2017-05-25 20:13:34 +02:00
hackrfinputplugin.h Tx support: interim state (1) 2016-12-29 12:41:10 +01:00
hackrfinputsettings.cpp HackRF output: continuous sample rate setting 2017-04-02 00:23:02 +02:00
hackrfinputsettings.h HackRF output: continuous sample rate setting 2017-04-02 00:23:02 +02:00
hackrfinputthread.cpp HackRF: rationalize start/stop device. Needs latest version of libhackrf (2017/03/01) and 2017.02.1 firmware 2017-04-26 16:35:05 +02:00
hackrfinputthread.h HackRF input plugin: pass thread pointer in the callback instead of using a static variable 2017-01-08 10:44:38 +01:00
readme.md Updated documentation 2017-05-19 10:52:18 +02:00

HackRF input plugin

Introduction

This intput sample source plugin gets its samples from a HackRF device.

Build

The plugin will be built only if the HackRF host library is installed in your system. If you build it from source and install it in a custom location say: /opt/install/libhackrf you will have to add -DLIBHACKRF_INCLUDE_DIR=/opt/install/libhackrf/include -DLIBHACKRF_LIBRARIES=/opt/install/libhackrf/lib/libhackrf.so to the cmake command line.

The HackRF Host library is also provided by many Linux distributions and is built in the SDRangel binary releases.

Interface

HackRF input plugin GUI

1: Common stream parameters

SDR Daemon FEC stream GUI

1.1: Frequency

This is the center frequency of reception in kHz.

1.2: Start/Stop

Device start / stop button.

  • Blue triangle icon: device is ready and can be started
  • Green square icon: device is running and can be stopped
  • Red square icon: an error occured. In the case the device was accidentally disconnected you may click on the icon, plug back in and start again.

Please note that HackRF is a half duplex device so if you have the Tx open in another tab you have to stop it first before starting the Rx for it to work properly. In a similar manner you should stop the Rx before resuming the Tx.

The settings on Tx or Rx tab are reapplied on start so provided the half duplex is handled correctly as stated above these settings can be considered independent.

1.3: Record

Record baseband I/Q stream toggle button

1.4: Baseband sample rate

Baseband I/Q sample rate in kS/s. This is the device sample rate (4) divided by the decimation factor (6).

2: Local Oscillator correction

Use this slider to adjust LO correction in ppm. It can be varied from -10.0 to 10.0 in 0.1 steps and is applied in software.

3: Auto correction options

These buttons control the local DSP auto correction options:

  • DC: auto remove DC component
  • IQ: auto make I/Q balance

4: Bias tee

Use this checkbox to toggle the +5V power supply on the antenna connector.

5:RF amp

Use this checkbox to toggle the extra low noise amplifier (LNA). This gives an additional gain of 14 dB.

6: Device sample rate

This is the HackRF device ADC sample rate in S/s.

Use the wheels to adjust the sample rate. Left click on a digit sets the cursor position at this digit. Right click on a digit sets all digits on the right to zero. This effectively floors value at the digit position. Wheels are moved with the mousewheel while pointing at the wheel or by selecting the wheel with the left mouse click and using the keyboard arroews. Pressing shift simultanoeusly moves digit by 5 and pressing control moves it by 2.

7: Rx filter bandwidth

This is the Rx filter bandwidth in kHz. Possible values are: 1750, 2500, 3500, 5000, 5500, 6000, 7000, 8000, 9000, 10000, 12000, 14000, 15000, 20000, 24000, 28000 kHz.

8: Decimation factor

The device stream from the HackRF is decimated to obtain the baseband stream. Possible values are:

  • 1: no decimation
  • 2: divide devcie stream sample rate by 2
  • 4: divide devcie stream sample rate by 4
  • 8: divide devcie stream sample rate by 8
  • 16: divide devcie stream sample rate by 16
  • 32: divide devcie stream sample rate by 32

10: Internal LNA gain

The LNA gain can be adjusted from 0 dB to 40 dB in 8 dB steps.

11: Rx variable gain amplifier gain

The Rx VGA gain can be adjusted from 0 dB to 62 dB in 2 dB steps.