92 lines
3.3 KiB
Plaintext
92 lines
3.3 KiB
Plaintext
|
The EtherDrive (R) HOWTO for users of 2.6 kernels is found at ...
|
||
|
|
|
||
|
|
http://www.coraid.com/support/linux/EtherDrive-2.6-HOWTO.html
|
||
|
|
|
||
|
|
It has many tips and hints!
|
||
|
|
|
||
|
|
CREATING DEVICE NODES
|
||
|
|
|
||
|
|
Users of udev should find the block device nodes created
|
||
|
|
automatically, but to create all the necessary device nodes, use the
|
||
|
|
udev configuration rules provided in udev.txt (in this directory).
|
||
|
|
|
||
|
|
There is a udev-install.sh script that shows how to install these
|
||
|
|
rules on your system.
|
||
|
|
|
||
|
|
If you are not using udev, two scripts are provided in
|
||
|
|
Documentation/aoe as examples of static device node creation for
|
||
|
|
using the aoe driver.
|
||
|
|
|
||
|
|
rm -rf /dev/etherd
|
||
|
|
sh Documentation/aoe/mkdevs.sh /dev/etherd
|
||
|
|
|
||
|
|
... or to make just one shelf's worth of block device nodes ...
|
||
|
|
|
||
|
|
sh Documentation/aoe/mkshelf.sh /dev/etherd 0
|
||
|
|
|
||
|
|
There is also an autoload script that shows how to edit
|
||
|
|
/etc/modprobe.conf to ensure that the aoe module is loaded when
|
||
|
|
necessary.
|
||
|
|
|
||
|
|
USING DEVICE NODES
|
||
|
|
|
||
|
|
"cat /dev/etherd/err" blocks, waiting for error diagnostic output,
|
||
|
|
like any retransmitted packets.
|
||
|
|
|
||
|
|
"echo eth2 eth4 > /dev/etherd/interfaces" tells the aoe driver to
|
||
|
|
limit ATA over Ethernet traffic to eth2 and eth4. AoE traffic from
|
||
|
|
untrusted networks should be ignored as a matter of security.
|
||
|
|
|
||
|
|
"echo > /dev/etherd/discover" tells the driver to find out what AoE
|
||
|
|
devices are available.
|
||
|
|
|
||
|
|
These character devices may disappear and be replaced by sysfs
|
||
|
|
counterparts, so distribution maintainers are encouraged to create
|
||
|
|
scripts that use these devices.
|
||
|
|
|
||
|
|
The block devices are named like this:
|
||
|
|
|
||
|
|
e{shelf}.{slot}
|
||
|
|
e{shelf}.{slot}p{part}
|
||
|
|
|
||
|
|
... so that "e0.2" is the third blade from the left (slot 2) in the
|
||
|
|
first shelf (shelf address zero). That's the whole disk. The first
|
||
|
|
partition on that disk would be "e0.2p1".
|
||
|
|
|
||
|
|
USING SYSFS
|
||
|
|
|
||
|
|
Each aoe block device in /sys/block has the extra attributes of
|
||
|
|
state, mac, and netif. The state attribute is "up" when the device
|
||
|
|
is ready for I/O and "down" if detected but unusable. The
|
||
|
|
"down,closewait" state shows that the device is still open and
|
||
|
|
cannot come up again until it has been closed.
|
||
|
|
|
||
|
|
The mac attribute is the ethernet address of the remote AoE device.
|
||
|
|
The netif attribute is the network interface on the localhost
|
||
|
|
through which we are communicating with the remote AoE device.
|
||
|
|
|
||
|
|
There is a script in this directory that formats this information
|
||
|
|
in a convenient way.
|
||
|
|
|
||
|
|
root@makki root# sh Documentation/aoe/status.sh
|
||
|
|
e10.0 eth3 up
|
||
|
|
e10.1 eth3 up
|
||
|
|
e10.2 eth3 up
|
||
|
|
e10.3 eth3 up
|
||
|
|
e10.4 eth3 up
|
||
|
|
e10.5 eth3 up
|
||
|
|
e10.6 eth3 up
|
||
|
|
e10.7 eth3 up
|
||
|
|
e10.8 eth3 up
|
||
|
|
e10.9 eth3 up
|
||
|
|
e4.0 eth1 up
|
||
|
|
e4.1 eth1 up
|
||
|
|
e4.2 eth1 up
|
||
|
|
e4.3 eth1 up
|
||
|
|
e4.4 eth1 up
|
||
|
|
e4.5 eth1 up
|
||
|
|
e4.6 eth1 up
|
||
|
|
e4.7 eth1 up
|
||
|
|
e4.8 eth1 up
|
||
|
|
e4.9 eth1 up
|