android_kernel_xiaomi_sm8350/drivers/scsi/lpfc/lpfc_attr.c

2659 lines
77 KiB
C
Raw Normal View History

/*******************************************************************
* This file is part of the Emulex Linux Device Driver for *
* Fibre Channel Host Bus Adapters. *
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
* Copyright (C) 2004-2008 Emulex. All rights reserved. *
* EMULEX and SLI are trademarks of Emulex. *
* www.emulex.com *
* Portions Copyright (C) 2004-2005 Christoph Hellwig *
* *
* This program is free software; you can redistribute it and/or *
* modify it under the terms of version 2 of the GNU General *
* Public License as published by the Free Software Foundation. *
* This program is distributed in the hope that it will be useful. *
* ALL EXPRESS OR IMPLIED CONDITIONS, REPRESENTATIONS AND *
* WARRANTIES, INCLUDING ANY IMPLIED WARRANTY OF MERCHANTABILITY, *
* FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT, ARE *
* DISCLAIMED, EXCEPT TO THE EXTENT THAT SUCH DISCLAIMERS ARE HELD *
* TO BE LEGALLY INVALID. See the GNU General Public License for *
* more details, a copy of which can be found in the file COPYING *
* included with this package. *
*******************************************************************/
#include <linux/ctype.h>
#include <linux/delay.h>
#include <linux/pci.h>
#include <linux/interrupt.h>
#include <scsi/scsi.h>
#include <scsi/scsi_device.h>
#include <scsi/scsi_host.h>
#include <scsi/scsi_tcq.h>
#include <scsi/scsi_transport_fc.h>
#include "lpfc_hw.h"
#include "lpfc_sli.h"
#include "lpfc_disc.h"
#include "lpfc_scsi.h"
#include "lpfc.h"
#include "lpfc_logmsg.h"
#include "lpfc_version.h"
#include "lpfc_compat.h"
#include "lpfc_crtn.h"
#include "lpfc_vport.h"
#define LPFC_DEF_DEVLOSS_TMO 30
#define LPFC_MIN_DEVLOSS_TMO 1
#define LPFC_MAX_DEVLOSS_TMO 255
#define LPFC_MAX_LINK_SPEED 8
#define LPFC_LINK_SPEED_BITMAP 0x00000117
#define LPFC_LINK_SPEED_STRING "0, 1, 2, 4, 8"
static void
lpfc_jedec_to_ascii(int incr, char hdw[])
{
int i, j;
for (i = 0; i < 8; i++) {
j = (incr & 0xf);
if (j <= 9)
hdw[7 - i] = 0x30 + j;
else
hdw[7 - i] = 0x61 + j - 10;
incr = (incr >> 4);
}
hdw[8] = 0;
return;
}
static ssize_t
lpfc_drvr_version_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
return snprintf(buf, PAGE_SIZE, LPFC_MODULE_DESC "\n");
}
static ssize_t
lpfc_info_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *host = class_to_shost(dev);
return snprintf(buf, PAGE_SIZE, "%s\n",lpfc_info(host));
}
static ssize_t
lpfc_serialnum_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "%s\n",phba->SerialNumber);
}
static ssize_t
lpfc_temp_sensor_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "%d\n",phba->temp_sensor_support);
}
static ssize_t
lpfc_modeldesc_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "%s\n",phba->ModelDesc);
}
static ssize_t
lpfc_modelname_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "%s\n",phba->ModelName);
}
static ssize_t
lpfc_programtype_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "%s\n",phba->ProgramType);
}
static ssize_t
lpfc_vportnum_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "%s\n",phba->Port);
}
static ssize_t
lpfc_fwrev_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
char fwrev[32];
lpfc_decode_firmware_rev(phba, fwrev, 1);
return snprintf(buf, PAGE_SIZE, "%s, sli-%d\n", fwrev, phba->sli_rev);
}
static ssize_t
lpfc_hdw_show(struct device *dev, struct device_attribute *attr, char *buf)
{
char hdw[9];
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
lpfc_vpd_t *vp = &phba->vpd;
lpfc_jedec_to_ascii(vp->rev.biuRev, hdw);
return snprintf(buf, PAGE_SIZE, "%s\n", hdw);
}
static ssize_t
lpfc_option_rom_version_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "%s\n", phba->OptionROMVersion);
}
static ssize_t
lpfc_link_state_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
int len = 0;
switch (phba->link_state) {
case LPFC_LINK_UNKNOWN:
case LPFC_WARM_START:
case LPFC_INIT_START:
case LPFC_INIT_MBX_CMDS:
case LPFC_LINK_DOWN:
case LPFC_HBA_ERROR:
len += snprintf(buf + len, PAGE_SIZE-len, "Link Down\n");
break;
case LPFC_LINK_UP:
case LPFC_CLEAR_LA:
case LPFC_HBA_READY:
len += snprintf(buf + len, PAGE_SIZE-len, "Link Up - ");
switch (vport->port_state) {
case LPFC_LOCAL_CFG_LINK:
len += snprintf(buf + len, PAGE_SIZE-len,
"Configuring Link\n");
break;
case LPFC_FDISC:
case LPFC_FLOGI:
case LPFC_FABRIC_CFG_LINK:
case LPFC_NS_REG:
case LPFC_NS_QRY:
case LPFC_BUILD_DISC_LIST:
case LPFC_DISC_AUTH:
len += snprintf(buf + len, PAGE_SIZE - len,
"Discovery\n");
break;
case LPFC_VPORT_READY:
len += snprintf(buf + len, PAGE_SIZE - len, "Ready\n");
break;
case LPFC_VPORT_FAILED:
len += snprintf(buf + len, PAGE_SIZE - len, "Failed\n");
break;
case LPFC_VPORT_UNKNOWN:
len += snprintf(buf + len, PAGE_SIZE - len,
"Unknown\n");
break;
}
if (phba->fc_topology == TOPOLOGY_LOOP) {
if (vport->fc_flag & FC_PUBLIC_LOOP)
len += snprintf(buf + len, PAGE_SIZE-len,
" Public Loop\n");
else
len += snprintf(buf + len, PAGE_SIZE-len,
" Private Loop\n");
} else {
if (vport->fc_flag & FC_FABRIC)
len += snprintf(buf + len, PAGE_SIZE-len,
" Fabric\n");
else
len += snprintf(buf + len, PAGE_SIZE-len,
" Point-2-Point\n");
}
}
return len;
}
static ssize_t
lpfc_num_discovered_ports_show(struct device *dev,
struct device_attribute *attr, char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
return snprintf(buf, PAGE_SIZE, "%d\n",
vport->fc_map_cnt + vport->fc_unmap_cnt);
}
static int
lpfc_issue_lip(struct Scsi_Host *shost)
{
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
LPFC_MBOXQ_t *pmboxq;
int mbxstatus = MBXERR_ERROR;
if ((vport->fc_flag & FC_OFFLINE_MODE) ||
(phba->sli.sli_flag & LPFC_BLOCK_MGMT_IO))
return -EPERM;
pmboxq = mempool_alloc(phba->mbox_mem_pool,GFP_KERNEL);
if (!pmboxq)
return -ENOMEM;
memset((void *)pmboxq, 0, sizeof (LPFC_MBOXQ_t));
pmboxq->mb.mbxCommand = MBX_DOWN_LINK;
pmboxq->mb.mbxOwner = OWN_HOST;
mbxstatus = lpfc_sli_issue_mbox_wait(phba, pmboxq, LPFC_MBOX_TMO * 2);
if ((mbxstatus == MBX_SUCCESS) && (pmboxq->mb.mbxStatus == 0)) {
memset((void *)pmboxq, 0, sizeof (LPFC_MBOXQ_t));
lpfc_init_link(phba, pmboxq, phba->cfg_topology,
phba->cfg_link_speed);
mbxstatus = lpfc_sli_issue_mbox_wait(phba, pmboxq,
phba->fc_ratov * 2);
}
lpfc_set_loopback_flag(phba);
if (mbxstatus != MBX_TIMEOUT)
mempool_free(pmboxq, phba->mbox_mem_pool);
if (mbxstatus == MBXERR_ERROR)
return -EIO;
return 0;
}
static int
lpfc_do_offline(struct lpfc_hba *phba, uint32_t type)
{
struct completion online_compl;
struct lpfc_sli_ring *pring;
struct lpfc_sli *psli;
int status = 0;
int cnt = 0;
int i;
init_completion(&online_compl);
lpfc_workq_post_event(phba, &status, &online_compl,
LPFC_EVT_OFFLINE_PREP);
wait_for_completion(&online_compl);
if (status != 0)
return -EIO;
psli = &phba->sli;
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
/* Wait a little for things to settle down, but not
* long enough for dev loss timeout to expire.
*/
for (i = 0; i < psli->num_rings; i++) {
pring = &psli->ring[i];
while (pring->txcmplq_cnt) {
msleep(10);
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
if (cnt++ > 500) { /* 5 secs */
lpfc_printf_log(phba,
KERN_WARNING, LOG_INIT,
"0466 Outstanding IO when "
"bringing Adapter offline\n");
break;
}
}
}
init_completion(&online_compl);
lpfc_workq_post_event(phba, &status, &online_compl, type);
wait_for_completion(&online_compl);
if (status != 0)
return -EIO;
return 0;
}
static int
lpfc_selective_reset(struct lpfc_hba *phba)
{
struct completion online_compl;
int status = 0;
if (!phba->cfg_enable_hba_reset)
return -EIO;
status = lpfc_do_offline(phba, LPFC_EVT_OFFLINE);
if (status != 0)
return status;
init_completion(&online_compl);
lpfc_workq_post_event(phba, &status, &online_compl,
LPFC_EVT_ONLINE);
wait_for_completion(&online_compl);
if (status != 0)
return -EIO;
return 0;
}
static ssize_t
lpfc_issue_reset(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
int status = -EINVAL;
if (strncmp(buf, "selective", sizeof("selective") - 1) == 0)
status = lpfc_selective_reset(phba);
if (status == 0)
return strlen(buf);
else
return status;
}
static ssize_t
lpfc_nport_evt_cnt_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "%d\n", phba->nport_event_cnt);
}
static ssize_t
lpfc_board_mode_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
char * state;
if (phba->link_state == LPFC_HBA_ERROR)
state = "error";
else if (phba->link_state == LPFC_WARM_START)
state = "warm start";
else if (phba->link_state == LPFC_INIT_START)
state = "offline";
else
state = "online";
return snprintf(buf, PAGE_SIZE, "%s\n", state);
}
static ssize_t
lpfc_board_mode_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
struct completion online_compl;
int status=0;
if (!phba->cfg_enable_hba_reset)
return -EACCES;
init_completion(&online_compl);
if(strncmp(buf, "online", sizeof("online") - 1) == 0) {
lpfc_workq_post_event(phba, &status, &online_compl,
LPFC_EVT_ONLINE);
wait_for_completion(&online_compl);
} else if (strncmp(buf, "offline", sizeof("offline") - 1) == 0)
status = lpfc_do_offline(phba, LPFC_EVT_OFFLINE);
else if (strncmp(buf, "warm", sizeof("warm") - 1) == 0)
status = lpfc_do_offline(phba, LPFC_EVT_WARM_START);
else if (strncmp(buf, "error", sizeof("error") - 1) == 0)
status = lpfc_do_offline(phba, LPFC_EVT_KILL);
else
return -EINVAL;
if (!status)
return strlen(buf);
else
return -EIO;
}
static int
lpfc_get_hba_info(struct lpfc_hba *phba,
uint32_t *mxri, uint32_t *axri,
uint32_t *mrpi, uint32_t *arpi,
uint32_t *mvpi, uint32_t *avpi)
{
struct lpfc_sli *psli = &phba->sli;
LPFC_MBOXQ_t *pmboxq;
MAILBOX_t *pmb;
int rc = 0;
/*
* prevent udev from issuing mailbox commands until the port is
* configured.
*/
if (phba->link_state < LPFC_LINK_DOWN ||
!phba->mbox_mem_pool ||
(phba->sli.sli_flag & LPFC_SLI2_ACTIVE) == 0)
return 0;
if (phba->sli.sli_flag & LPFC_BLOCK_MGMT_IO)
return 0;
pmboxq = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
if (!pmboxq)
return 0;
memset(pmboxq, 0, sizeof (LPFC_MBOXQ_t));
pmb = &pmboxq->mb;
pmb->mbxCommand = MBX_READ_CONFIG;
pmb->mbxOwner = OWN_HOST;
pmboxq->context1 = NULL;
if ((phba->pport->fc_flag & FC_OFFLINE_MODE) ||
(!(psli->sli_flag & LPFC_SLI2_ACTIVE)))
rc = MBX_NOT_FINISHED;
else
rc = lpfc_sli_issue_mbox_wait(phba, pmboxq, phba->fc_ratov * 2);
if (rc != MBX_SUCCESS) {
if (rc != MBX_TIMEOUT)
mempool_free(pmboxq, phba->mbox_mem_pool);
return 0;
}
if (mrpi)
*mrpi = pmb->un.varRdConfig.max_rpi;
if (arpi)
*arpi = pmb->un.varRdConfig.avail_rpi;
if (mxri)
*mxri = pmb->un.varRdConfig.max_xri;
if (axri)
*axri = pmb->un.varRdConfig.avail_xri;
if (mvpi)
*mvpi = pmb->un.varRdConfig.max_vpi;
if (avpi)
*avpi = pmb->un.varRdConfig.avail_vpi;
mempool_free(pmboxq, phba->mbox_mem_pool);
return 1;
}
static ssize_t
lpfc_max_rpi_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
uint32_t cnt;
if (lpfc_get_hba_info(phba, NULL, NULL, &cnt, NULL, NULL, NULL))
return snprintf(buf, PAGE_SIZE, "%d\n", cnt);
return snprintf(buf, PAGE_SIZE, "Unknown\n");
}
static ssize_t
lpfc_used_rpi_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
uint32_t cnt, acnt;
if (lpfc_get_hba_info(phba, NULL, NULL, &cnt, &acnt, NULL, NULL))
return snprintf(buf, PAGE_SIZE, "%d\n", (cnt - acnt));
return snprintf(buf, PAGE_SIZE, "Unknown\n");
}
static ssize_t
lpfc_max_xri_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
uint32_t cnt;
if (lpfc_get_hba_info(phba, &cnt, NULL, NULL, NULL, NULL, NULL))
return snprintf(buf, PAGE_SIZE, "%d\n", cnt);
return snprintf(buf, PAGE_SIZE, "Unknown\n");
}
static ssize_t
lpfc_used_xri_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
uint32_t cnt, acnt;
if (lpfc_get_hba_info(phba, &cnt, &acnt, NULL, NULL, NULL, NULL))
return snprintf(buf, PAGE_SIZE, "%d\n", (cnt - acnt));
return snprintf(buf, PAGE_SIZE, "Unknown\n");
}
static ssize_t
lpfc_max_vpi_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
uint32_t cnt;
if (lpfc_get_hba_info(phba, NULL, NULL, NULL, NULL, &cnt, NULL))
return snprintf(buf, PAGE_SIZE, "%d\n", cnt);
return snprintf(buf, PAGE_SIZE, "Unknown\n");
}
static ssize_t
lpfc_used_vpi_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
uint32_t cnt, acnt;
if (lpfc_get_hba_info(phba, NULL, NULL, NULL, NULL, &cnt, &acnt))
return snprintf(buf, PAGE_SIZE, "%d\n", (cnt - acnt));
return snprintf(buf, PAGE_SIZE, "Unknown\n");
}
static ssize_t
lpfc_npiv_info_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
if (!(phba->max_vpi))
return snprintf(buf, PAGE_SIZE, "NPIV Not Supported\n");
if (vport->port_type == LPFC_PHYSICAL_PORT)
return snprintf(buf, PAGE_SIZE, "NPIV Physical\n");
return snprintf(buf, PAGE_SIZE, "NPIV Virtual (VPI %d)\n", vport->vpi);
}
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
static ssize_t
lpfc_poll_show(struct device *dev, struct device_attribute *attr,
char *buf)
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
return snprintf(buf, PAGE_SIZE, "%#x\n", phba->cfg_poll);
}
static ssize_t
lpfc_poll_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
uint32_t creg_val;
uint32_t old_val;
int val=0;
if (!isdigit(buf[0]))
return -EINVAL;
if (sscanf(buf, "%i", &val) != 1)
return -EINVAL;
if ((val & 0x3) != val)
return -EINVAL;
spin_lock_irq(&phba->hbalock);
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
old_val = phba->cfg_poll;
if (val & ENABLE_FCP_RING_POLLING) {
if ((val & DISABLE_FCP_RING_INT) &&
!(old_val & DISABLE_FCP_RING_INT)) {
creg_val = readl(phba->HCregaddr);
creg_val &= ~(HC_R0INT_ENA << LPFC_FCP_RING);
writel(creg_val, phba->HCregaddr);
readl(phba->HCregaddr); /* flush */
lpfc_poll_start_timer(phba);
}
} else if (val != 0x0) {
spin_unlock_irq(&phba->hbalock);
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
return -EINVAL;
}
if (!(val & DISABLE_FCP_RING_INT) &&
(old_val & DISABLE_FCP_RING_INT))
{
spin_unlock_irq(&phba->hbalock);
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
del_timer(&phba->fcp_poll_timer);
spin_lock_irq(&phba->hbalock);
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
creg_val = readl(phba->HCregaddr);
creg_val |= (HC_R0INT_ENA << LPFC_FCP_RING);
writel(creg_val, phba->HCregaddr);
readl(phba->HCregaddr); /* flush */
}
phba->cfg_poll = val;
spin_unlock_irq(&phba->hbalock);
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
return strlen(buf);
}
#define lpfc_param_show(attr) \
static ssize_t \
lpfc_##attr##_show(struct device *dev, struct device_attribute *attr, \
char *buf) \
{ \
struct Scsi_Host *shost = class_to_shost(dev);\
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;\
struct lpfc_hba *phba = vport->phba;\
int val = 0;\
val = phba->cfg_##attr;\
return snprintf(buf, PAGE_SIZE, "%d\n",\
phba->cfg_##attr);\
}
#define lpfc_param_hex_show(attr) \
static ssize_t \
lpfc_##attr##_show(struct device *dev, struct device_attribute *attr, \
char *buf) \
{ \
struct Scsi_Host *shost = class_to_shost(dev);\
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;\
struct lpfc_hba *phba = vport->phba;\
int val = 0;\
val = phba->cfg_##attr;\
return snprintf(buf, PAGE_SIZE, "%#x\n",\
phba->cfg_##attr);\
}
#define lpfc_param_init(attr, default, minval, maxval) \
static int \
lpfc_##attr##_init(struct lpfc_hba *phba, int val) \
{ \
if (val >= minval && val <= maxval) {\
phba->cfg_##attr = val;\
return 0;\
}\
lpfc_printf_log(phba, KERN_ERR, LOG_INIT, \
"0449 lpfc_"#attr" attribute cannot be set to %d, "\
"allowed range is ["#minval", "#maxval"]\n", val); \
phba->cfg_##attr = default;\
return -EINVAL;\
}
#define lpfc_param_set(attr, default, minval, maxval) \
static int \
lpfc_##attr##_set(struct lpfc_hba *phba, int val) \
{ \
if (val >= minval && val <= maxval) {\
phba->cfg_##attr = val;\
return 0;\
}\
lpfc_printf_log(phba, KERN_ERR, LOG_INIT, \
"0450 lpfc_"#attr" attribute cannot be set to %d, "\
"allowed range is ["#minval", "#maxval"]\n", val); \
return -EINVAL;\
}
#define lpfc_param_store(attr) \
static ssize_t \
lpfc_##attr##_store(struct device *dev, struct device_attribute *attr, \
const char *buf, size_t count) \
{ \
struct Scsi_Host *shost = class_to_shost(dev);\
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;\
struct lpfc_hba *phba = vport->phba;\
int val=0;\
if (!isdigit(buf[0]))\
return -EINVAL;\
if (sscanf(buf, "%i", &val) != 1)\
return -EINVAL;\
if (lpfc_##attr##_set(phba, val) == 0) \
return strlen(buf);\
else \
return -EINVAL;\
}
#define lpfc_vport_param_show(attr) \
static ssize_t \
lpfc_##attr##_show(struct device *dev, struct device_attribute *attr, \
char *buf) \
{ \
struct Scsi_Host *shost = class_to_shost(dev);\
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;\
int val = 0;\
val = vport->cfg_##attr;\
return snprintf(buf, PAGE_SIZE, "%d\n", vport->cfg_##attr);\
}
#define lpfc_vport_param_hex_show(attr) \
static ssize_t \
lpfc_##attr##_show(struct device *dev, struct device_attribute *attr, \
char *buf) \
{ \
struct Scsi_Host *shost = class_to_shost(dev);\
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;\
int val = 0;\
val = vport->cfg_##attr;\
return snprintf(buf, PAGE_SIZE, "%#x\n", vport->cfg_##attr);\
}
#define lpfc_vport_param_init(attr, default, minval, maxval) \
static int \
lpfc_##attr##_init(struct lpfc_vport *vport, int val) \
{ \
if (val >= minval && val <= maxval) {\
vport->cfg_##attr = val;\
return 0;\
}\
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT, \
"0449 lpfc_"#attr" attribute cannot be set to %d, "\
"allowed range is ["#minval", "#maxval"]\n", val); \
vport->cfg_##attr = default;\
return -EINVAL;\
}
#define lpfc_vport_param_set(attr, default, minval, maxval) \
static int \
lpfc_##attr##_set(struct lpfc_vport *vport, int val) \
{ \
if (val >= minval && val <= maxval) {\
vport->cfg_##attr = val;\
return 0;\
}\
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT, \
"0450 lpfc_"#attr" attribute cannot be set to %d, "\
"allowed range is ["#minval", "#maxval"]\n", val); \
return -EINVAL;\
}
#define lpfc_vport_param_store(attr) \
static ssize_t \
lpfc_##attr##_store(struct device *dev, struct device_attribute *attr, \
const char *buf, size_t count) \
{ \
struct Scsi_Host *shost = class_to_shost(dev);\
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;\
int val=0;\
if (!isdigit(buf[0]))\
return -EINVAL;\
if (sscanf(buf, "%i", &val) != 1)\
return -EINVAL;\
if (lpfc_##attr##_set(vport, val) == 0) \
return strlen(buf);\
else \
return -EINVAL;\
}
#define LPFC_ATTR(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_param_init(name, defval, minval, maxval)
#define LPFC_ATTR_R(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_param_show(name)\
lpfc_param_init(name, defval, minval, maxval)\
static DEVICE_ATTR(lpfc_##name, S_IRUGO , lpfc_##name##_show, NULL)
#define LPFC_ATTR_RW(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_param_show(name)\
lpfc_param_init(name, defval, minval, maxval)\
lpfc_param_set(name, defval, minval, maxval)\
lpfc_param_store(name)\
static DEVICE_ATTR(lpfc_##name, S_IRUGO | S_IWUSR,\
lpfc_##name##_show, lpfc_##name##_store)
#define LPFC_ATTR_HEX_R(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_param_hex_show(name)\
lpfc_param_init(name, defval, minval, maxval)\
static DEVICE_ATTR(lpfc_##name, S_IRUGO , lpfc_##name##_show, NULL)
#define LPFC_ATTR_HEX_RW(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_param_hex_show(name)\
lpfc_param_init(name, defval, minval, maxval)\
lpfc_param_set(name, defval, minval, maxval)\
lpfc_param_store(name)\
static DEVICE_ATTR(lpfc_##name, S_IRUGO | S_IWUSR,\
lpfc_##name##_show, lpfc_##name##_store)
#define LPFC_VPORT_ATTR(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_vport_param_init(name, defval, minval, maxval)
#define LPFC_VPORT_ATTR_R(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_vport_param_show(name)\
lpfc_vport_param_init(name, defval, minval, maxval)\
static DEVICE_ATTR(lpfc_##name, S_IRUGO , lpfc_##name##_show, NULL)
#define LPFC_VPORT_ATTR_RW(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_vport_param_show(name)\
lpfc_vport_param_init(name, defval, minval, maxval)\
lpfc_vport_param_set(name, defval, minval, maxval)\
lpfc_vport_param_store(name)\
static DEVICE_ATTR(lpfc_##name, S_IRUGO | S_IWUSR,\
lpfc_##name##_show, lpfc_##name##_store)
#define LPFC_VPORT_ATTR_HEX_R(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_vport_param_hex_show(name)\
lpfc_vport_param_init(name, defval, minval, maxval)\
static DEVICE_ATTR(lpfc_##name, S_IRUGO , lpfc_##name##_show, NULL)
#define LPFC_VPORT_ATTR_HEX_RW(name, defval, minval, maxval, desc) \
static int lpfc_##name = defval;\
module_param(lpfc_##name, int, 0);\
MODULE_PARM_DESC(lpfc_##name, desc);\
lpfc_vport_param_hex_show(name)\
lpfc_vport_param_init(name, defval, minval, maxval)\
lpfc_vport_param_set(name, defval, minval, maxval)\
lpfc_vport_param_store(name)\
static DEVICE_ATTR(lpfc_##name, S_IRUGO | S_IWUSR,\
lpfc_##name##_show, lpfc_##name##_store)
static DEVICE_ATTR(info, S_IRUGO, lpfc_info_show, NULL);
static DEVICE_ATTR(serialnum, S_IRUGO, lpfc_serialnum_show, NULL);
static DEVICE_ATTR(modeldesc, S_IRUGO, lpfc_modeldesc_show, NULL);
static DEVICE_ATTR(modelname, S_IRUGO, lpfc_modelname_show, NULL);
static DEVICE_ATTR(programtype, S_IRUGO, lpfc_programtype_show, NULL);
static DEVICE_ATTR(portnum, S_IRUGO, lpfc_vportnum_show, NULL);
static DEVICE_ATTR(fwrev, S_IRUGO, lpfc_fwrev_show, NULL);
static DEVICE_ATTR(hdw, S_IRUGO, lpfc_hdw_show, NULL);
static DEVICE_ATTR(link_state, S_IRUGO, lpfc_link_state_show, NULL);
static DEVICE_ATTR(option_rom_version, S_IRUGO,
lpfc_option_rom_version_show, NULL);
static DEVICE_ATTR(num_discovered_ports, S_IRUGO,
lpfc_num_discovered_ports_show, NULL);
static DEVICE_ATTR(nport_evt_cnt, S_IRUGO, lpfc_nport_evt_cnt_show, NULL);
static DEVICE_ATTR(lpfc_drvr_version, S_IRUGO, lpfc_drvr_version_show, NULL);
static DEVICE_ATTR(board_mode, S_IRUGO | S_IWUSR,
lpfc_board_mode_show, lpfc_board_mode_store);
static DEVICE_ATTR(issue_reset, S_IWUSR, NULL, lpfc_issue_reset);
static DEVICE_ATTR(max_vpi, S_IRUGO, lpfc_max_vpi_show, NULL);
static DEVICE_ATTR(used_vpi, S_IRUGO, lpfc_used_vpi_show, NULL);
static DEVICE_ATTR(max_rpi, S_IRUGO, lpfc_max_rpi_show, NULL);
static DEVICE_ATTR(used_rpi, S_IRUGO, lpfc_used_rpi_show, NULL);
static DEVICE_ATTR(max_xri, S_IRUGO, lpfc_max_xri_show, NULL);
static DEVICE_ATTR(used_xri, S_IRUGO, lpfc_used_xri_show, NULL);
static DEVICE_ATTR(npiv_info, S_IRUGO, lpfc_npiv_info_show, NULL);
static DEVICE_ATTR(lpfc_temp_sensor, S_IRUGO, lpfc_temp_sensor_show, NULL);
static char *lpfc_soft_wwn_key = "C99G71SL8032A";
static ssize_t
lpfc_soft_wwn_enable_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
unsigned int cnt = count;
/*
* We're doing a simple sanity check for soft_wwpn setting.
* We require that the user write a specific key to enable
* the soft_wwpn attribute to be settable. Once the attribute
* is written, the enable key resets. If further updates are
* desired, the key must be written again to re-enable the
* attribute.
*
* The "key" is not secret - it is a hardcoded string shown
* here. The intent is to protect against the random user or
* application that is just writing attributes.
*/
/* count may include a LF at end of string */
if (buf[cnt-1] == '\n')
cnt--;
if ((cnt != strlen(lpfc_soft_wwn_key)) ||
(strncmp(buf, lpfc_soft_wwn_key, strlen(lpfc_soft_wwn_key)) != 0))
return -EINVAL;
phba->soft_wwn_enable = 1;
return count;
}
static DEVICE_ATTR(lpfc_soft_wwn_enable, S_IWUSR, NULL,
lpfc_soft_wwn_enable_store);
static ssize_t
lpfc_soft_wwpn_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
return snprintf(buf, PAGE_SIZE, "0x%llx\n",
(unsigned long long)phba->cfg_soft_wwpn);
}
static ssize_t
lpfc_soft_wwpn_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
struct completion online_compl;
int stat1=0, stat2=0;
unsigned int i, j, cnt=count;
u8 wwpn[8];
if (!phba->cfg_enable_hba_reset)
return -EACCES;
spin_lock_irq(&phba->hbalock);
if (phba->over_temp_state == HBA_OVER_TEMP) {
spin_unlock_irq(&phba->hbalock);
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
return -EACCES;
}
spin_unlock_irq(&phba->hbalock);
/* count may include a LF at end of string */
if (buf[cnt-1] == '\n')
cnt--;
if (!phba->soft_wwn_enable || (cnt < 16) || (cnt > 18) ||
((cnt == 17) && (*buf++ != 'x')) ||
((cnt == 18) && ((*buf++ != '0') || (*buf++ != 'x'))))
return -EINVAL;
phba->soft_wwn_enable = 0;
memset(wwpn, 0, sizeof(wwpn));
/* Validate and store the new name */
for (i=0, j=0; i < 16; i++) {
if ((*buf >= 'a') && (*buf <= 'f'))
j = ((j << 4) | ((*buf++ -'a') + 10));
else if ((*buf >= 'A') && (*buf <= 'F'))
j = ((j << 4) | ((*buf++ -'A') + 10));
else if ((*buf >= '0') && (*buf <= '9'))
j = ((j << 4) | (*buf++ -'0'));
else
return -EINVAL;
if (i % 2) {
wwpn[i/2] = j & 0xff;
j = 0;
}
}
phba->cfg_soft_wwpn = wwn_to_u64(wwpn);
fc_host_port_name(shost) = phba->cfg_soft_wwpn;
if (phba->cfg_soft_wwnn)
fc_host_node_name(shost) = phba->cfg_soft_wwnn;
dev_printk(KERN_NOTICE, &phba->pcidev->dev,
"lpfc%d: Reinitializing to use soft_wwpn\n", phba->brd_no);
stat1 = lpfc_do_offline(phba, LPFC_EVT_OFFLINE);
if (stat1)
lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
"0463 lpfc_soft_wwpn attribute set failed to "
"reinit adapter - %d\n", stat1);
init_completion(&online_compl);
lpfc_workq_post_event(phba, &stat2, &online_compl, LPFC_EVT_ONLINE);
wait_for_completion(&online_compl);
if (stat2)
lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
"0464 lpfc_soft_wwpn attribute set failed to "
"reinit adapter - %d\n", stat2);
return (stat1 || stat2) ? -EIO : count;
}
static DEVICE_ATTR(lpfc_soft_wwpn, S_IRUGO | S_IWUSR,\
lpfc_soft_wwpn_show, lpfc_soft_wwpn_store);
static ssize_t
lpfc_soft_wwnn_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_hba *phba = ((struct lpfc_vport *)shost->hostdata)->phba;
return snprintf(buf, PAGE_SIZE, "0x%llx\n",
(unsigned long long)phba->cfg_soft_wwnn);
}
static ssize_t
lpfc_soft_wwnn_store(struct device *dev, struct device_attribute *attr,
const char *buf, size_t count)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_hba *phba = ((struct lpfc_vport *)shost->hostdata)->phba;
unsigned int i, j, cnt=count;
u8 wwnn[8];
/* count may include a LF at end of string */
if (buf[cnt-1] == '\n')
cnt--;
if (!phba->soft_wwn_enable || (cnt < 16) || (cnt > 18) ||
((cnt == 17) && (*buf++ != 'x')) ||
((cnt == 18) && ((*buf++ != '0') || (*buf++ != 'x'))))
return -EINVAL;
/*
* Allow wwnn to be set many times, as long as the enable is set.
* However, once the wwpn is set, everything locks.
*/
memset(wwnn, 0, sizeof(wwnn));
/* Validate and store the new name */
for (i=0, j=0; i < 16; i++) {
if ((*buf >= 'a') && (*buf <= 'f'))
j = ((j << 4) | ((*buf++ -'a') + 10));
else if ((*buf >= 'A') && (*buf <= 'F'))
j = ((j << 4) | ((*buf++ -'A') + 10));
else if ((*buf >= '0') && (*buf <= '9'))
j = ((j << 4) | (*buf++ -'0'));
else
return -EINVAL;
if (i % 2) {
wwnn[i/2] = j & 0xff;
j = 0;
}
}
phba->cfg_soft_wwnn = wwn_to_u64(wwnn);
dev_printk(KERN_NOTICE, &phba->pcidev->dev,
"lpfc%d: soft_wwnn set. Value will take effect upon "
"setting of the soft_wwpn\n", phba->brd_no);
return count;
}
static DEVICE_ATTR(lpfc_soft_wwnn, S_IRUGO | S_IWUSR,\
lpfc_soft_wwnn_show, lpfc_soft_wwnn_store);
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
static int lpfc_poll = 0;
module_param(lpfc_poll, int, 0);
MODULE_PARM_DESC(lpfc_poll, "FCP ring polling mode control:"
" 0 - none,"
" 1 - poll with interrupts enabled"
" 3 - poll and disable FCP ring interrupts");
static DEVICE_ATTR(lpfc_poll, S_IRUGO | S_IWUSR,
lpfc_poll_show, lpfc_poll_store);
int lpfc_sli_mode = 0;
module_param(lpfc_sli_mode, int, 0);
MODULE_PARM_DESC(lpfc_sli_mode, "SLI mode selector:"
" 0 - auto (SLI-3 if supported),"
" 2 - select SLI-2 even on SLI-3 capable HBAs,"
" 3 - select SLI-3");
int lpfc_enable_npiv = 0;
module_param(lpfc_enable_npiv, int, 0);
MODULE_PARM_DESC(lpfc_enable_npiv, "Enable NPIV functionality");
lpfc_param_show(enable_npiv);
lpfc_param_init(enable_npiv, 0, 0, 1);
static DEVICE_ATTR(lpfc_enable_npiv, S_IRUGO,
lpfc_enable_npiv_show, NULL);
/*
# lpfc_nodev_tmo: If set, it will hold all I/O errors on devices that disappear
# until the timer expires. Value range is [0,255]. Default value is 30.
*/
static int lpfc_nodev_tmo = LPFC_DEF_DEVLOSS_TMO;
static int lpfc_devloss_tmo = LPFC_DEF_DEVLOSS_TMO;
module_param(lpfc_nodev_tmo, int, 0);
MODULE_PARM_DESC(lpfc_nodev_tmo,
"Seconds driver will hold I/O waiting "
"for a device to come back");
static ssize_t
lpfc_nodev_tmo_show(struct device *dev, struct device_attribute *attr,
char *buf)
{
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
int val = 0;
val = vport->cfg_devloss_tmo;
return snprintf(buf, PAGE_SIZE, "%d\n", vport->cfg_devloss_tmo);
}
static int
lpfc_nodev_tmo_init(struct lpfc_vport *vport, int val)
{
if (vport->cfg_devloss_tmo != LPFC_DEF_DEVLOSS_TMO) {
vport->cfg_nodev_tmo = vport->cfg_devloss_tmo;
if (val != LPFC_DEF_DEVLOSS_TMO)
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
"0402 Ignoring nodev_tmo module "
"parameter because devloss_tmo is "
"set.\n");
return 0;
}
if (val >= LPFC_MIN_DEVLOSS_TMO && val <= LPFC_MAX_DEVLOSS_TMO) {
vport->cfg_nodev_tmo = val;
vport->cfg_devloss_tmo = val;
return 0;
}
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
"0400 lpfc_nodev_tmo attribute cannot be set to"
" %d, allowed range is [%d, %d]\n",
val, LPFC_MIN_DEVLOSS_TMO, LPFC_MAX_DEVLOSS_TMO);
vport->cfg_nodev_tmo = LPFC_DEF_DEVLOSS_TMO;
return -EINVAL;
}
static void
lpfc_update_rport_devloss_tmo(struct lpfc_vport *vport)
{
struct Scsi_Host *shost;
struct lpfc_nodelist *ndlp;
shost = lpfc_shost_from_vport(vport);
spin_lock_irq(shost->host_lock);
list_for_each_entry(ndlp, &vport->fc_nodes, nlp_listp)
if (NLP_CHK_NODE_ACT(ndlp) && ndlp->rport)
ndlp->rport->dev_loss_tmo = vport->cfg_devloss_tmo;
spin_unlock_irq(shost->host_lock);
}
static int
lpfc_nodev_tmo_set(struct lpfc_vport *vport, int val)
{
if (vport->dev_loss_tmo_changed ||
(lpfc_devloss_tmo != LPFC_DEF_DEVLOSS_TMO)) {
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
"0401 Ignoring change to nodev_tmo "
"because devloss_tmo is set.\n");
return 0;
}
if (val >= LPFC_MIN_DEVLOSS_TMO && val <= LPFC_MAX_DEVLOSS_TMO) {
vport->cfg_nodev_tmo = val;
vport->cfg_devloss_tmo = val;
lpfc_update_rport_devloss_tmo(vport);
return 0;
}
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
"0403 lpfc_nodev_tmo attribute cannot be set to"
"%d, allowed range is [%d, %d]\n",
val, LPFC_MIN_DEVLOSS_TMO, LPFC_MAX_DEVLOSS_TMO);
return -EINVAL;
}
lpfc_vport_param_store(nodev_tmo)
static DEVICE_ATTR(lpfc_nodev_tmo, S_IRUGO | S_IWUSR,
lpfc_nodev_tmo_show, lpfc_nodev_tmo_store);
/*
# lpfc_devloss_tmo: If set, it will hold all I/O errors on devices that
# disappear until the timer expires. Value range is [0,255]. Default
# value is 30.
*/
module_param(lpfc_devloss_tmo, int, 0);
MODULE_PARM_DESC(lpfc_devloss_tmo,
"Seconds driver will hold I/O waiting "
"for a device to come back");
lpfc_vport_param_init(devloss_tmo, LPFC_DEF_DEVLOSS_TMO,
LPFC_MIN_DEVLOSS_TMO, LPFC_MAX_DEVLOSS_TMO)
lpfc_vport_param_show(devloss_tmo)
static int
lpfc_devloss_tmo_set(struct lpfc_vport *vport, int val)
{
if (val >= LPFC_MIN_DEVLOSS_TMO && val <= LPFC_MAX_DEVLOSS_TMO) {
vport->cfg_nodev_tmo = val;
vport->cfg_devloss_tmo = val;
vport->dev_loss_tmo_changed = 1;
lpfc_update_rport_devloss_tmo(vport);
return 0;
}
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
"0404 lpfc_devloss_tmo attribute cannot be set to"
" %d, allowed range is [%d, %d]\n",
val, LPFC_MIN_DEVLOSS_TMO, LPFC_MAX_DEVLOSS_TMO);
return -EINVAL;
}
lpfc_vport_param_store(devloss_tmo)
static DEVICE_ATTR(lpfc_devloss_tmo, S_IRUGO | S_IWUSR,
lpfc_devloss_tmo_show, lpfc_devloss_tmo_store);
/*
# lpfc_log_verbose: Only turn this flag on if you are willing to risk being
# deluged with LOTS of information.
# You can set a bit mask to record specific types of verbose messages:
#
# LOG_ELS 0x1 ELS events
# LOG_DISCOVERY 0x2 Link discovery events
# LOG_MBOX 0x4 Mailbox events
# LOG_INIT 0x8 Initialization events
# LOG_LINK_EVENT 0x10 Link events
# LOG_FCP 0x40 FCP traffic history
# LOG_NODE 0x80 Node table events
# LOG_MISC 0x400 Miscellaneous events
# LOG_SLI 0x800 SLI events
# LOG_FCP_ERROR 0x1000 Only log FCP errors
# LOG_LIBDFC 0x2000 LIBDFC events
# LOG_ALL_MSG 0xffff LOG all messages
*/
LPFC_VPORT_ATTR_HEX_RW(log_verbose, 0x0, 0x0, 0xffff,
"Verbose logging bit-mask");
/*
# lpfc_enable_da_id: This turns on the DA_ID CT command that deregisters
# objects that have been registered with the nameserver after login.
*/
LPFC_VPORT_ATTR_R(enable_da_id, 0, 0, 1,
"Deregister nameserver objects before LOGO");
/*
# lun_queue_depth: This parameter is used to limit the number of outstanding
# commands per FCP LUN. Value range is [1,128]. Default value is 30.
*/
LPFC_VPORT_ATTR_R(lun_queue_depth, 30, 1, 128,
"Max number of FCP commands we can queue to a specific LUN");
/*
# hba_queue_depth: This parameter is used to limit the number of outstanding
# commands per lpfc HBA. Value range is [32,8192]. If this parameter
# value is greater than the maximum number of exchanges supported by the HBA,
# then maximum number of exchanges supported by the HBA is used to determine
# the hba_queue_depth.
*/
LPFC_ATTR_R(hba_queue_depth, 8192, 32, 8192,
"Max number of FCP commands we can queue to a lpfc HBA");
/*
# peer_port_login: This parameter allows/prevents logins
# between peer ports hosted on the same physical port.
# When this parameter is set 0 peer ports of same physical port
# are not allowed to login to each other.
# When this parameter is set 1 peer ports of same physical port
# are allowed to login to each other.
# Default value of this parameter is 0.
*/
LPFC_VPORT_ATTR_R(peer_port_login, 0, 0, 1,
"Allow peer ports on the same physical port to login to each "
"other.");
/*
# restrict_login: This parameter allows/prevents logins
# between Virtual Ports and remote initiators.
# When this parameter is not set (0) Virtual Ports will accept PLOGIs from
# other initiators and will attempt to PLOGI all remote ports.
# When this parameter is set (1) Virtual Ports will reject PLOGIs from
# remote ports and will not attempt to PLOGI to other initiators.
# This parameter does not restrict to the physical port.
# This parameter does not restrict logins to Fabric resident remote ports.
# Default value of this parameter is 1.
*/
static int lpfc_restrict_login = 1;
module_param(lpfc_restrict_login, int, 0);
MODULE_PARM_DESC(lpfc_restrict_login,
"Restrict virtual ports login to remote initiators.");
lpfc_vport_param_show(restrict_login);
static int
lpfc_restrict_login_init(struct lpfc_vport *vport, int val)
{
if (val < 0 || val > 1) {
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
"0449 lpfc_restrict_login attribute cannot "
"be set to %d, allowed range is [0, 1]\n",
val);
vport->cfg_restrict_login = 1;
return -EINVAL;
}
if (vport->port_type == LPFC_PHYSICAL_PORT) {
vport->cfg_restrict_login = 0;
return 0;
}
vport->cfg_restrict_login = val;
return 0;
}
static int
lpfc_restrict_login_set(struct lpfc_vport *vport, int val)
{
if (val < 0 || val > 1) {
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
"0450 lpfc_restrict_login attribute cannot "
"be set to %d, allowed range is [0, 1]\n",
val);
vport->cfg_restrict_login = 1;
return -EINVAL;
}
if (vport->port_type == LPFC_PHYSICAL_PORT && val != 0) {
lpfc_printf_vlog(vport, KERN_ERR, LOG_INIT,
"0468 lpfc_restrict_login must be 0 for "
"Physical ports.\n");
vport->cfg_restrict_login = 0;
return 0;
}
vport->cfg_restrict_login = val;
return 0;
}
lpfc_vport_param_store(restrict_login);
static DEVICE_ATTR(lpfc_restrict_login, S_IRUGO | S_IWUSR,
lpfc_restrict_login_show, lpfc_restrict_login_store);
/*
# Some disk devices have a "select ID" or "select Target" capability.
# From a protocol standpoint "select ID" usually means select the
# Fibre channel "ALPA". In the FC-AL Profile there is an "informative
# annex" which contains a table that maps a "select ID" (a number
# between 0 and 7F) to an ALPA. By default, for compatibility with
# older drivers, the lpfc driver scans this table from low ALPA to high
# ALPA.
#
# Turning on the scan-down variable (on = 1, off = 0) will
# cause the lpfc driver to use an inverted table, effectively
# scanning ALPAs from high to low. Value range is [0,1]. Default value is 1.
#
# (Note: This "select ID" functionality is a LOOP ONLY characteristic
# and will not work across a fabric. Also this parameter will take
# effect only in the case when ALPA map is not available.)
*/
LPFC_VPORT_ATTR_R(scan_down, 1, 0, 1,
"Start scanning for devices from highest ALPA to lowest");
/*
# lpfc_topology: link topology for init link
# 0x0 = attempt loop mode then point-to-point
# 0x01 = internal loopback mode
# 0x02 = attempt point-to-point mode only
# 0x04 = attempt loop mode only
# 0x06 = attempt point-to-point mode then loop
# Set point-to-point mode if you want to run as an N_Port.
# Set loop mode if you want to run as an NL_Port. Value range is [0,0x6].
# Default value is 0.
*/
static int
lpfc_topology_set(struct lpfc_hba *phba, int val)
{
int err;
uint32_t prev_val;
if (val >= 0 && val <= 6) {
prev_val = phba->cfg_topology;
phba->cfg_topology = val;
err = lpfc_issue_lip(lpfc_shost_from_vport(phba->pport));
if (err)
phba->cfg_topology = prev_val;
return err;
}
lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
"%d:0467 lpfc_topology attribute cannot be set to %d, "
"allowed range is [0, 6]\n",
phba->brd_no, val);
return -EINVAL;
}
static int lpfc_topology = 0;
module_param(lpfc_topology, int, 0);
MODULE_PARM_DESC(lpfc_topology, "Select Fibre Channel topology");
lpfc_param_show(topology)
lpfc_param_init(topology, 0, 0, 6)
lpfc_param_store(topology)
static DEVICE_ATTR(lpfc_topology, S_IRUGO | S_IWUSR,
lpfc_topology_show, lpfc_topology_store);
/*
# lpfc_link_speed: Link speed selection for initializing the Fibre Channel
# connection.
# 0 = auto select (default)
# 1 = 1 Gigabaud
# 2 = 2 Gigabaud
# 4 = 4 Gigabaud
# 8 = 8 Gigabaud
# Value range is [0,8]. Default value is 0.
*/
static int
lpfc_link_speed_set(struct lpfc_hba *phba, int val)
{
int err;
uint32_t prev_val;
if (((val == LINK_SPEED_1G) && !(phba->lmt & LMT_1Gb)) ||
((val == LINK_SPEED_2G) && !(phba->lmt & LMT_2Gb)) ||
((val == LINK_SPEED_4G) && !(phba->lmt & LMT_4Gb)) ||
((val == LINK_SPEED_8G) && !(phba->lmt & LMT_8Gb)) ||
((val == LINK_SPEED_10G) && !(phba->lmt & LMT_10Gb)))
return -EINVAL;
if ((val >= 0 && val <= LPFC_MAX_LINK_SPEED)
&& (LPFC_LINK_SPEED_BITMAP & (1 << val))) {
prev_val = phba->cfg_link_speed;
phba->cfg_link_speed = val;
err = lpfc_issue_lip(lpfc_shost_from_vport(phba->pport));
if (err)
phba->cfg_link_speed = prev_val;
return err;
}
lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
"%d:0469 lpfc_link_speed attribute cannot be set to %d, "
"allowed range is [0, 8]\n",
phba->brd_no, val);
return -EINVAL;
}
static int lpfc_link_speed = 0;
module_param(lpfc_link_speed, int, 0);
MODULE_PARM_DESC(lpfc_link_speed, "Select link speed");
lpfc_param_show(link_speed)
static int
lpfc_link_speed_init(struct lpfc_hba *phba, int val)
{
if ((val >= 0 && val <= LPFC_MAX_LINK_SPEED)
&& (LPFC_LINK_SPEED_BITMAP & (1 << val))) {
phba->cfg_link_speed = val;
return 0;
}
lpfc_printf_log(phba, KERN_ERR, LOG_INIT,
"0454 lpfc_link_speed attribute cannot "
"be set to %d, allowed values are "
"["LPFC_LINK_SPEED_STRING"]\n", val);
phba->cfg_link_speed = 0;
return -EINVAL;
}
lpfc_param_store(link_speed)
static DEVICE_ATTR(lpfc_link_speed, S_IRUGO | S_IWUSR,
lpfc_link_speed_show, lpfc_link_speed_store);
/*
# lpfc_fcp_class: Determines FC class to use for the FCP protocol.
# Value range is [2,3]. Default value is 3.
*/
LPFC_VPORT_ATTR_R(fcp_class, 3, 2, 3,
"Select Fibre Channel class of service for FCP sequences");
/*
# lpfc_use_adisc: Use ADISC for FCP rediscovery instead of PLOGI. Value range
# is [0,1]. Default value is 0.
*/
LPFC_VPORT_ATTR_RW(use_adisc, 0, 0, 1,
"Use ADISC on rediscovery to authenticate FCP devices");
/*
# lpfc_ack0: Use ACK0, instead of ACK1 for class 2 acknowledgement. Value
# range is [0,1]. Default value is 0.
*/
LPFC_ATTR_R(ack0, 0, 0, 1, "Enable ACK0 support");
/*
# lpfc_cr_delay & lpfc_cr_count: Default values for I/O colaesing
# cr_delay (msec) or cr_count outstanding commands. cr_delay can take
# value [0,63]. cr_count can take value [1,255]. Default value of cr_delay
# is 0. Default value of cr_count is 1. The cr_count feature is disabled if
# cr_delay is set to 0.
*/
LPFC_ATTR_RW(cr_delay, 0, 0, 63, "A count of milliseconds after which an "
"interrupt response is generated");
LPFC_ATTR_RW(cr_count, 1, 1, 255, "A count of I/O completions after which an "
"interrupt response is generated");
/*
# lpfc_multi_ring_support: Determines how many rings to spread available
# cmd/rsp IOCB entries across.
# Value range is [1,2]. Default value is 1.
*/
LPFC_ATTR_R(multi_ring_support, 1, 1, 2, "Determines number of primary "
"SLI rings to spread IOCB entries across");
/*
# lpfc_multi_ring_rctl: If lpfc_multi_ring_support is enabled, this
# identifies what rctl value to configure the additional ring for.
# Value range is [1,0xff]. Default value is 4 (Unsolicated Data).
*/
LPFC_ATTR_R(multi_ring_rctl, FC_UNSOL_DATA, 1,
255, "Identifies RCTL for additional ring configuration");
/*
# lpfc_multi_ring_type: If lpfc_multi_ring_support is enabled, this
# identifies what type value to configure the additional ring for.
# Value range is [1,0xff]. Default value is 5 (LLC/SNAP).
*/
LPFC_ATTR_R(multi_ring_type, FC_LLC_SNAP, 1,
255, "Identifies TYPE for additional ring configuration");
/*
# lpfc_fdmi_on: controls FDMI support.
# 0 = no FDMI support
# 1 = support FDMI without attribute of hostname
# 2 = support FDMI with attribute of hostname
# Value range [0,2]. Default value is 0.
*/
LPFC_VPORT_ATTR_RW(fdmi_on, 0, 0, 2, "Enable FDMI support");
/*
# Specifies the maximum number of ELS cmds we can have outstanding (for
# discovery). Value range is [1,64]. Default value = 32.
*/
LPFC_VPORT_ATTR(discovery_threads, 32, 1, 64, "Maximum number of ELS commands "
"during discovery");
/*
# lpfc_max_luns: maximum allowed LUN.
# Value range is [0,65535]. Default value is 255.
# NOTE: The SCSI layer might probe all allowed LUN on some old targets.
*/
LPFC_VPORT_ATTR_R(max_luns, 255, 0, 65535, "Maximum allowed LUN");
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
/*
# lpfc_poll_tmo: .Milliseconds driver will wait between polling FCP ring.
# Value range is [1,255], default value is 10.
*/
LPFC_ATTR_RW(poll_tmo, 10, 1, 255,
"Milliseconds driver will wait between polling FCP ring");
/*
# lpfc_use_msi: Use MSI (Message Signaled Interrupts) in systems that
# support this feature
# 0 = MSI disabled (default)
# 1 = MSI enabled
# 2 = MSI-X enabled
# Value range is [0,2]. Default value is 0.
*/
LPFC_ATTR_R(use_msi, 0, 0, 2, "Use Message Signaled Interrupts (1) or "
"MSI-X (2), if possible");
/*
# lpfc_enable_hba_reset: Allow or prevent HBA resets to the hardware.
# 0 = HBA resets disabled
# 1 = HBA resets enabled (default)
# Value range is [0,1]. Default value is 1.
*/
LPFC_ATTR_R(enable_hba_reset, 1, 0, 1, "Enable HBA resets from the driver.");
/*
# lpfc_enable_hba_heartbeat: Enable HBA heartbeat timer..
# 0 = HBA Heartbeat disabled
# 1 = HBA Heartbeat enabled (default)
# Value range is [0,1]. Default value is 1.
*/
LPFC_ATTR_R(enable_hba_heartbeat, 1, 0, 1, "Enable HBA Heartbeat.");
/*
* lpfc_sg_seg_cnt: Initial Maximum DMA Segment Count
* This value can be set to values between 64 and 256. The default value is
* 64, but may be increased to allow for larger Max I/O sizes. The scsi layer
* will be allowed to request I/Os of sizes up to (MAX_SEG_COUNT * SEG_SIZE).
*/
LPFC_ATTR_R(sg_seg_cnt, LPFC_DEFAULT_SG_SEG_CNT, LPFC_DEFAULT_SG_SEG_CNT,
LPFC_MAX_SG_SEG_CNT, "Max Scatter Gather Segment Count");
struct device_attribute *lpfc_hba_attrs[] = {
&dev_attr_info,
&dev_attr_serialnum,
&dev_attr_modeldesc,
&dev_attr_modelname,
&dev_attr_programtype,
&dev_attr_portnum,
&dev_attr_fwrev,
&dev_attr_hdw,
&dev_attr_option_rom_version,
&dev_attr_link_state,
&dev_attr_num_discovered_ports,
&dev_attr_lpfc_drvr_version,
&dev_attr_lpfc_temp_sensor,
&dev_attr_lpfc_log_verbose,
&dev_attr_lpfc_lun_queue_depth,
&dev_attr_lpfc_hba_queue_depth,
&dev_attr_lpfc_peer_port_login,
&dev_attr_lpfc_nodev_tmo,
&dev_attr_lpfc_devloss_tmo,
&dev_attr_lpfc_fcp_class,
&dev_attr_lpfc_use_adisc,
&dev_attr_lpfc_ack0,
&dev_attr_lpfc_topology,
&dev_attr_lpfc_scan_down,
&dev_attr_lpfc_link_speed,
&dev_attr_lpfc_cr_delay,
&dev_attr_lpfc_cr_count,
&dev_attr_lpfc_multi_ring_support,
&dev_attr_lpfc_multi_ring_rctl,
&dev_attr_lpfc_multi_ring_type,
&dev_attr_lpfc_fdmi_on,
&dev_attr_lpfc_max_luns,
&dev_attr_lpfc_enable_npiv,
&dev_attr_nport_evt_cnt,
&dev_attr_board_mode,
&dev_attr_max_vpi,
&dev_attr_used_vpi,
&dev_attr_max_rpi,
&dev_attr_used_rpi,
&dev_attr_max_xri,
&dev_attr_used_xri,
&dev_attr_npiv_info,
&dev_attr_issue_reset,
&dev_attr_lpfc_poll,
&dev_attr_lpfc_poll_tmo,
&dev_attr_lpfc_use_msi,
&dev_attr_lpfc_soft_wwnn,
&dev_attr_lpfc_soft_wwpn,
&dev_attr_lpfc_soft_wwn_enable,
&dev_attr_lpfc_enable_hba_reset,
&dev_attr_lpfc_enable_hba_heartbeat,
&dev_attr_lpfc_sg_seg_cnt,
NULL,
};
struct device_attribute *lpfc_vport_attrs[] = {
&dev_attr_info,
&dev_attr_link_state,
&dev_attr_num_discovered_ports,
&dev_attr_lpfc_drvr_version,
&dev_attr_lpfc_log_verbose,
&dev_attr_lpfc_lun_queue_depth,
&dev_attr_lpfc_nodev_tmo,
&dev_attr_lpfc_devloss_tmo,
&dev_attr_lpfc_hba_queue_depth,
&dev_attr_lpfc_peer_port_login,
&dev_attr_lpfc_restrict_login,
&dev_attr_lpfc_fcp_class,
&dev_attr_lpfc_use_adisc,
&dev_attr_lpfc_fdmi_on,
&dev_attr_lpfc_max_luns,
&dev_attr_nport_evt_cnt,
&dev_attr_npiv_info,
&dev_attr_lpfc_enable_da_id,
NULL,
};
static ssize_t
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes Well, first of all, I don't want to change so many files either. What I do: Adding a new parameter "struct bin_attribute *" in the .read/.write methods for the sysfs binary attributes. In fact, only the four lines change in fs/sysfs/bin.c and include/linux/sysfs.h do the real work. But I have to update all the files that use binary attributes to make them compatible with the new .read and .write methods. I'm not sure if I missed any. :( Why I do this: For a sysfs attribute, we can get a pointer pointing to the struct attribute in the .show/.store method, while we can't do this for the binary attributes. I don't know why this is different, but this does make it not so handy to use the binary attributes as the regular ones. So I think this patch is reasonable. :) Who benefits from it: The patch that exposes ACPI tables in sysfs requires such an improvement. All the table binary attributes share the same .read method. Parameter "struct bin_attribute *" is used to get the table signature and instance number which are used to distinguish different ACPI table binary attributes. Without this parameter, we need to offer different .read methods for different ACPI table binary attributes. This is impossible as there are various ACPI tables on different platforms, and we don't know what they are until they are loaded. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-06-09 01:57:22 -04:00
sysfs_ctlreg_write(struct kobject *kobj, struct bin_attribute *bin_attr,
char *buf, loff_t off, size_t count)
{
size_t buf_off;
struct device *dev = container_of(kobj, struct device, kobj);
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
if ((off + count) > FF_REG_AREA_SIZE)
return -ERANGE;
if (count == 0) return 0;
if (off % 4 || count % 4 || (unsigned long)buf % 4)
return -EINVAL;
if (!(vport->fc_flag & FC_OFFLINE_MODE)) {
return -EPERM;
}
spin_lock_irq(&phba->hbalock);
for (buf_off = 0; buf_off < count; buf_off += sizeof(uint32_t))
writel(*((uint32_t *)(buf + buf_off)),
phba->ctrl_regs_memmap_p + off + buf_off);
spin_unlock_irq(&phba->hbalock);
return count;
}
static ssize_t
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes Well, first of all, I don't want to change so many files either. What I do: Adding a new parameter "struct bin_attribute *" in the .read/.write methods for the sysfs binary attributes. In fact, only the four lines change in fs/sysfs/bin.c and include/linux/sysfs.h do the real work. But I have to update all the files that use binary attributes to make them compatible with the new .read and .write methods. I'm not sure if I missed any. :( Why I do this: For a sysfs attribute, we can get a pointer pointing to the struct attribute in the .show/.store method, while we can't do this for the binary attributes. I don't know why this is different, but this does make it not so handy to use the binary attributes as the regular ones. So I think this patch is reasonable. :) Who benefits from it: The patch that exposes ACPI tables in sysfs requires such an improvement. All the table binary attributes share the same .read method. Parameter "struct bin_attribute *" is used to get the table signature and instance number which are used to distinguish different ACPI table binary attributes. Without this parameter, we need to offer different .read methods for different ACPI table binary attributes. This is impossible as there are various ACPI tables on different platforms, and we don't know what they are until they are loaded. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-06-09 01:57:22 -04:00
sysfs_ctlreg_read(struct kobject *kobj, struct bin_attribute *bin_attr,
char *buf, loff_t off, size_t count)
{
size_t buf_off;
uint32_t * tmp_ptr;
struct device *dev = container_of(kobj, struct device, kobj);
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
if (off > FF_REG_AREA_SIZE)
return -ERANGE;
if ((off + count) > FF_REG_AREA_SIZE)
count = FF_REG_AREA_SIZE - off;
if (count == 0) return 0;
if (off % 4 || count % 4 || (unsigned long)buf % 4)
return -EINVAL;
spin_lock_irq(&phba->hbalock);
for (buf_off = 0; buf_off < count; buf_off += sizeof(uint32_t)) {
tmp_ptr = (uint32_t *)(buf + buf_off);
*tmp_ptr = readl(phba->ctrl_regs_memmap_p + off + buf_off);
}
spin_unlock_irq(&phba->hbalock);
return count;
}
static struct bin_attribute sysfs_ctlreg_attr = {
.attr = {
.name = "ctlreg",
.mode = S_IRUSR | S_IWUSR,
},
.size = 256,
.read = sysfs_ctlreg_read,
.write = sysfs_ctlreg_write,
};
static void
sysfs_mbox_idle(struct lpfc_hba *phba)
{
phba->sysfs_mbox.state = SMBOX_IDLE;
phba->sysfs_mbox.offset = 0;
if (phba->sysfs_mbox.mbox) {
mempool_free(phba->sysfs_mbox.mbox,
phba->mbox_mem_pool);
phba->sysfs_mbox.mbox = NULL;
}
}
static ssize_t
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes Well, first of all, I don't want to change so many files either. What I do: Adding a new parameter "struct bin_attribute *" in the .read/.write methods for the sysfs binary attributes. In fact, only the four lines change in fs/sysfs/bin.c and include/linux/sysfs.h do the real work. But I have to update all the files that use binary attributes to make them compatible with the new .read and .write methods. I'm not sure if I missed any. :( Why I do this: For a sysfs attribute, we can get a pointer pointing to the struct attribute in the .show/.store method, while we can't do this for the binary attributes. I don't know why this is different, but this does make it not so handy to use the binary attributes as the regular ones. So I think this patch is reasonable. :) Who benefits from it: The patch that exposes ACPI tables in sysfs requires such an improvement. All the table binary attributes share the same .read method. Parameter "struct bin_attribute *" is used to get the table signature and instance number which are used to distinguish different ACPI table binary attributes. Without this parameter, we need to offer different .read methods for different ACPI table binary attributes. This is impossible as there are various ACPI tables on different platforms, and we don't know what they are until they are loaded. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-06-09 01:57:22 -04:00
sysfs_mbox_write(struct kobject *kobj, struct bin_attribute *bin_attr,
char *buf, loff_t off, size_t count)
{
struct device *dev = container_of(kobj, struct device, kobj);
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
struct lpfcMboxq *mbox = NULL;
if ((count + off) > MAILBOX_CMD_SIZE)
return -ERANGE;
if (off % 4 || count % 4 || (unsigned long)buf % 4)
return -EINVAL;
if (count == 0)
return 0;
if (off == 0) {
mbox = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
if (!mbox)
return -ENOMEM;
memset(mbox, 0, sizeof (LPFC_MBOXQ_t));
}
spin_lock_irq(&phba->hbalock);
if (off == 0) {
if (phba->sysfs_mbox.mbox)
mempool_free(mbox, phba->mbox_mem_pool);
else
phba->sysfs_mbox.mbox = mbox;
phba->sysfs_mbox.state = SMBOX_WRITING;
} else {
if (phba->sysfs_mbox.state != SMBOX_WRITING ||
phba->sysfs_mbox.offset != off ||
phba->sysfs_mbox.mbox == NULL) {
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return -EAGAIN;
}
}
memcpy((uint8_t *) & phba->sysfs_mbox.mbox->mb + off,
buf, count);
phba->sysfs_mbox.offset = off + count;
spin_unlock_irq(&phba->hbalock);
return count;
}
static ssize_t
sysfs: add parameter "struct bin_attribute *" in .read/.write methods for sysfs binary attributes Well, first of all, I don't want to change so many files either. What I do: Adding a new parameter "struct bin_attribute *" in the .read/.write methods for the sysfs binary attributes. In fact, only the four lines change in fs/sysfs/bin.c and include/linux/sysfs.h do the real work. But I have to update all the files that use binary attributes to make them compatible with the new .read and .write methods. I'm not sure if I missed any. :( Why I do this: For a sysfs attribute, we can get a pointer pointing to the struct attribute in the .show/.store method, while we can't do this for the binary attributes. I don't know why this is different, but this does make it not so handy to use the binary attributes as the regular ones. So I think this patch is reasonable. :) Who benefits from it: The patch that exposes ACPI tables in sysfs requires such an improvement. All the table binary attributes share the same .read method. Parameter "struct bin_attribute *" is used to get the table signature and instance number which are used to distinguish different ACPI table binary attributes. Without this parameter, we need to offer different .read methods for different ACPI table binary attributes. This is impossible as there are various ACPI tables on different platforms, and we don't know what they are until they are loaded. Signed-off-by: Zhang Rui <rui.zhang@intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
2007-06-09 01:57:22 -04:00
sysfs_mbox_read(struct kobject *kobj, struct bin_attribute *bin_attr,
char *buf, loff_t off, size_t count)
{
struct device *dev = container_of(kobj, struct device, kobj);
struct Scsi_Host *shost = class_to_shost(dev);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
int rc;
if (off > MAILBOX_CMD_SIZE)
return -ERANGE;
if ((count + off) > MAILBOX_CMD_SIZE)
count = MAILBOX_CMD_SIZE - off;
if (off % 4 || count % 4 || (unsigned long)buf % 4)
return -EINVAL;
if (off && count == 0)
return 0;
spin_lock_irq(&phba->hbalock);
if (phba->over_temp_state == HBA_OVER_TEMP) {
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
return -EACCES;
}
if (off == 0 &&
phba->sysfs_mbox.state == SMBOX_WRITING &&
phba->sysfs_mbox.offset >= 2 * sizeof(uint32_t)) {
switch (phba->sysfs_mbox.mbox->mb.mbxCommand) {
/* Offline only */
case MBX_INIT_LINK:
case MBX_DOWN_LINK:
case MBX_CONFIG_LINK:
case MBX_CONFIG_RING:
case MBX_RESET_RING:
case MBX_UNREG_LOGIN:
case MBX_CLEAR_LA:
case MBX_DUMP_CONTEXT:
case MBX_RUN_DIAGS:
case MBX_RESTART:
case MBX_SET_MASK:
case MBX_SET_DEBUG:
if (!(vport->fc_flag & FC_OFFLINE_MODE)) {
printk(KERN_WARNING "mbox_read:Command 0x%x "
"is illegal in on-line state\n",
phba->sysfs_mbox.mbox->mb.mbxCommand);
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return -EPERM;
}
case MBX_WRITE_NV:
case MBX_WRITE_VPARMS:
case MBX_LOAD_SM:
case MBX_READ_NV:
case MBX_READ_CONFIG:
case MBX_READ_RCONFIG:
case MBX_READ_STATUS:
case MBX_READ_XRI:
case MBX_READ_REV:
case MBX_READ_LNK_STAT:
case MBX_DUMP_MEMORY:
case MBX_DOWN_LOAD:
case MBX_UPDATE_CFG:
case MBX_KILL_BOARD:
case MBX_LOAD_AREA:
case MBX_LOAD_EXP_ROM:
case MBX_BEACON:
case MBX_DEL_LD_ENTRY:
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
case MBX_SET_VARIABLE:
case MBX_WRITE_WWN:
break;
case MBX_READ_SPARM64:
case MBX_READ_LA:
case MBX_READ_LA64:
case MBX_REG_LOGIN:
case MBX_REG_LOGIN64:
case MBX_CONFIG_PORT:
case MBX_RUN_BIU_DIAG:
printk(KERN_WARNING "mbox_read: Illegal Command 0x%x\n",
phba->sysfs_mbox.mbox->mb.mbxCommand);
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return -EPERM;
default:
printk(KERN_WARNING "mbox_read: Unknown Command 0x%x\n",
phba->sysfs_mbox.mbox->mb.mbxCommand);
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return -EPERM;
}
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
/* If HBA encountered an error attention, allow only DUMP
* or RESTART mailbox commands until the HBA is restarted.
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
*/
if ((phba->pport->stopped) &&
(phba->sysfs_mbox.mbox->mb.mbxCommand !=
MBX_DUMP_MEMORY &&
phba->sysfs_mbox.mbox->mb.mbxCommand !=
MBX_RESTART &&
phba->sysfs_mbox.mbox->mb.mbxCommand !=
MBX_WRITE_VPARMS)) {
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return -EPERM;
}
phba->sysfs_mbox.mbox->vport = vport;
[SCSI] lpfc 8.2.6 : Multiple discovery fixes Multiple Discovery Fixes: - Fix race on discovery due to link events coinciding with vport_delete. - Use NLP_FABRIC state to filter out switch-based pseudo initiators that reuse the same WWNs. - Correct erroneous setting of DID=0 in lpfc_matchdid() - Correct extra reference count that was in the lookup path for the remoteid from an unsolicited ELS. - Correct double-free bug in els abort path. - Correct FDMI server discovery logic for switch that return a WWN of 0. - Fix bugs in ndlp mgmt when a node changes address - Correct bug that did not delete RSCNs for vports upon link transitions - Fix "0216 Link event during NS query" error which pops up when vports are swapped to different switch ports. - Add sanity checks on ndlp structures - Fix devloss log message to dump WWN correctly - Hold off mgmt commands that were interferring with discovery mailbox cmds - Remove unnecessary FC_ESTABLISH_LINK logic. - Correct some race conditions in the worker thread, resulting in devloss: - Clear the work_port_events field before handling the work port events - Clear the deferred ring event before handling a deferred ring event - Hold the hba lock when waking up the work thread - Send an acc for the rscn even when we aren't going to handle it - Fix locking behavior that was not properly protecting the ACTIVE flag, thus allowing mailbox command order to shift. Signed-off-by: James Smart <james.smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-04-07 10:15:56 -04:00
/* Don't allow mailbox commands to be sent when blocked
* or when in the middle of discovery
*/
if (phba->sli.sli_flag & LPFC_BLOCK_MGMT_IO ||
vport->fc_flag & FC_NDISC_ACTIVE) {
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return -EAGAIN;
}
if ((vport->fc_flag & FC_OFFLINE_MODE) ||
(!(phba->sli.sli_flag & LPFC_SLI2_ACTIVE))){
spin_unlock_irq(&phba->hbalock);
rc = lpfc_sli_issue_mbox (phba,
phba->sysfs_mbox.mbox,
MBX_POLL);
spin_lock_irq(&phba->hbalock);
} else {
spin_unlock_irq(&phba->hbalock);
rc = lpfc_sli_issue_mbox_wait (phba,
phba->sysfs_mbox.mbox,
lpfc_mbox_tmo_val(phba,
phba->sysfs_mbox.mbox->mb.mbxCommand) * HZ);
spin_lock_irq(&phba->hbalock);
}
if (rc != MBX_SUCCESS) {
if (rc == MBX_TIMEOUT) {
phba->sysfs_mbox.mbox = NULL;
}
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return (rc == MBX_TIMEOUT) ? -ETIME : -ENODEV;
}
phba->sysfs_mbox.state = SMBOX_READING;
}
else if (phba->sysfs_mbox.offset != off ||
phba->sysfs_mbox.state != SMBOX_READING) {
printk(KERN_WARNING "mbox_read: Bad State\n");
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return -EAGAIN;
}
memcpy(buf, (uint8_t *) & phba->sysfs_mbox.mbox->mb + off, count);
phba->sysfs_mbox.offset = off + count;
if (phba->sysfs_mbox.offset == MAILBOX_CMD_SIZE)
sysfs_mbox_idle(phba);
spin_unlock_irq(&phba->hbalock);
return count;
}
static struct bin_attribute sysfs_mbox_attr = {
.attr = {
.name = "mbox",
.mode = S_IRUSR | S_IWUSR,
},
.size = MAILBOX_CMD_SIZE,
.read = sysfs_mbox_read,
.write = sysfs_mbox_write,
};
int
lpfc_alloc_sysfs_attr(struct lpfc_vport *vport)
{
struct Scsi_Host *shost = lpfc_shost_from_vport(vport);
int error;
error = sysfs_create_bin_file(&shost->shost_dev.kobj,
&sysfs_ctlreg_attr);
if (error)
goto out;
error = sysfs_create_bin_file(&shost->shost_dev.kobj,
&sysfs_mbox_attr);
if (error)
goto out_remove_ctlreg_attr;
return 0;
out_remove_ctlreg_attr:
sysfs_remove_bin_file(&shost->shost_dev.kobj, &sysfs_ctlreg_attr);
out:
return error;
}
void
lpfc_free_sysfs_attr(struct lpfc_vport *vport)
{
struct Scsi_Host *shost = lpfc_shost_from_vport(vport);
sysfs_remove_bin_file(&shost->shost_dev.kobj, &sysfs_mbox_attr);
sysfs_remove_bin_file(&shost->shost_dev.kobj, &sysfs_ctlreg_attr);
}
/*
* Dynamic FC Host Attributes Support
*/
static void
lpfc_get_host_port_id(struct Scsi_Host *shost)
{
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
/* note: fc_myDID already in cpu endianness */
fc_host_port_id(shost) = vport->fc_myDID;
}
static void
lpfc_get_host_port_type(struct Scsi_Host *shost)
{
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
spin_lock_irq(shost->host_lock);
if (vport->port_type == LPFC_NPIV_PORT) {
fc_host_port_type(shost) = FC_PORTTYPE_NPIV;
} else if (lpfc_is_link_up(phba)) {
if (phba->fc_topology == TOPOLOGY_LOOP) {
if (vport->fc_flag & FC_PUBLIC_LOOP)
fc_host_port_type(shost) = FC_PORTTYPE_NLPORT;
else
fc_host_port_type(shost) = FC_PORTTYPE_LPORT;
} else {
if (vport->fc_flag & FC_FABRIC)
fc_host_port_type(shost) = FC_PORTTYPE_NPORT;
else
fc_host_port_type(shost) = FC_PORTTYPE_PTP;
}
} else
fc_host_port_type(shost) = FC_PORTTYPE_UNKNOWN;
spin_unlock_irq(shost->host_lock);
}
static void
lpfc_get_host_port_state(struct Scsi_Host *shost)
{
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
spin_lock_irq(shost->host_lock);
if (vport->fc_flag & FC_OFFLINE_MODE)
fc_host_port_state(shost) = FC_PORTSTATE_OFFLINE;
else {
switch (phba->link_state) {
case LPFC_LINK_UNKNOWN:
case LPFC_LINK_DOWN:
fc_host_port_state(shost) = FC_PORTSTATE_LINKDOWN;
break;
case LPFC_LINK_UP:
case LPFC_CLEAR_LA:
case LPFC_HBA_READY:
/* Links up, beyond this port_type reports state */
fc_host_port_state(shost) = FC_PORTSTATE_ONLINE;
break;
case LPFC_HBA_ERROR:
fc_host_port_state(shost) = FC_PORTSTATE_ERROR;
break;
default:
fc_host_port_state(shost) = FC_PORTSTATE_UNKNOWN;
break;
}
}
spin_unlock_irq(shost->host_lock);
}
static void
lpfc_get_host_speed(struct Scsi_Host *shost)
{
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
spin_lock_irq(shost->host_lock);
if (lpfc_is_link_up(phba)) {
switch(phba->fc_linkspeed) {
case LA_1GHZ_LINK:
fc_host_speed(shost) = FC_PORTSPEED_1GBIT;
break;
case LA_2GHZ_LINK:
fc_host_speed(shost) = FC_PORTSPEED_2GBIT;
break;
case LA_4GHZ_LINK:
fc_host_speed(shost) = FC_PORTSPEED_4GBIT;
break;
case LA_8GHZ_LINK:
fc_host_speed(shost) = FC_PORTSPEED_8GBIT;
break;
default:
fc_host_speed(shost) = FC_PORTSPEED_UNKNOWN;
break;
}
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
} else
fc_host_speed(shost) = FC_PORTSPEED_UNKNOWN;
spin_unlock_irq(shost->host_lock);
}
static void
lpfc_get_host_fabric_name (struct Scsi_Host *shost)
{
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
u64 node_name;
spin_lock_irq(shost->host_lock);
if ((vport->fc_flag & FC_FABRIC) ||
((phba->fc_topology == TOPOLOGY_LOOP) &&
(vport->fc_flag & FC_PUBLIC_LOOP)))
node_name = wwn_to_u64(phba->fc_fabparam.nodeName.u.wwn);
else
/* fabric is local port if there is no F/FL_Port */
[SCSI] lpfc 8.2.4 : Miscellaneous Fixes Miscellaneous Fixes: - Fix a couple of sparse complaints - Reset the FCP recovery flag when the node is not a FCP2 device. - Speed up offline prep delays - Fixed a memory leak in lpfc_mem_alloc failure path - Fixed external loopback test. - Fixed error code returned from the driver when HBA is over heated. - Correct Max NPIV vport to limits read from adapter - Add missing locks around fc_flag and FC_NEEDS_REG_VPI - Add missing hba ids for device identification - Added support for SET_VARIABLE and MBX_WRITE_WWN mailbox commands - Changed all temperature event messages from warning to error - Fix reporting of link speed when link is down - Added support for MBX_WRITE_WWN mailbox command - Change del_timer_sync() in ISR to del_timer() in interrupt handler - Correct instances of beXX_to_cpu() that should be cpu_to_beXX() - Perform target flush before releasing node references on module unload - Avoid bogus devloss_tmo messages when driver unloads - Fix panic when HBA generates ERATT interupt - Fix mbox race condition and a workaround on back-to-back mailbox commands - Force NPIV off for pt2pt mode between 2 NPorts - Stop worker thread before removing fc_host. - Fix up discovery timeout error case due to missing clear_la - Tighten mailbox polling code to speed up detection of fast completions - Only allow DUMP_MEMORY if adapter offline due to overtemp errors - Added extended error information to the log messages in chip init. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
2008-01-11 01:52:54 -05:00
node_name = 0;
spin_unlock_irq(shost->host_lock);
fc_host_fabric_name(shost) = node_name;
}
static struct fc_host_statistics *
lpfc_get_stats(struct Scsi_Host *shost)
{
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
struct lpfc_sli *psli = &phba->sli;
struct fc_host_statistics *hs = &phba->link_stats;
struct lpfc_lnk_stat * lso = &psli->lnk_stat_offsets;
LPFC_MBOXQ_t *pmboxq;
MAILBOX_t *pmb;
unsigned long seconds;
int rc = 0;
/*
* prevent udev from issuing mailbox commands until the port is
* configured.
*/
if (phba->link_state < LPFC_LINK_DOWN ||
!phba->mbox_mem_pool ||
(phba->sli.sli_flag & LPFC_SLI2_ACTIVE) == 0)
return NULL;
if (phba->sli.sli_flag & LPFC_BLOCK_MGMT_IO)
return NULL;
pmboxq = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
if (!pmboxq)
return NULL;
memset(pmboxq, 0, sizeof (LPFC_MBOXQ_t));
pmb = &pmboxq->mb;
pmb->mbxCommand = MBX_READ_STATUS;
pmb->mbxOwner = OWN_HOST;
pmboxq->context1 = NULL;
pmboxq->vport = vport;
if ((vport->fc_flag & FC_OFFLINE_MODE) ||
(!(psli->sli_flag & LPFC_SLI2_ACTIVE)))
rc = lpfc_sli_issue_mbox(phba, pmboxq, MBX_POLL);
else
rc = lpfc_sli_issue_mbox_wait(phba, pmboxq, phba->fc_ratov * 2);
if (rc != MBX_SUCCESS) {
if (rc != MBX_TIMEOUT)
mempool_free(pmboxq, phba->mbox_mem_pool);
return NULL;
}
memset(hs, 0, sizeof (struct fc_host_statistics));
hs->tx_frames = pmb->un.varRdStatus.xmitFrameCnt;
hs->tx_words = (pmb->un.varRdStatus.xmitByteCnt * 256);
hs->rx_frames = pmb->un.varRdStatus.rcvFrameCnt;
hs->rx_words = (pmb->un.varRdStatus.rcvByteCnt * 256);
memset(pmboxq, 0, sizeof (LPFC_MBOXQ_t));
pmb->mbxCommand = MBX_READ_LNK_STAT;
pmb->mbxOwner = OWN_HOST;
pmboxq->context1 = NULL;
pmboxq->vport = vport;
if ((vport->fc_flag & FC_OFFLINE_MODE) ||
(!(psli->sli_flag & LPFC_SLI2_ACTIVE)))
rc = lpfc_sli_issue_mbox(phba, pmboxq, MBX_POLL);
else
rc = lpfc_sli_issue_mbox_wait(phba, pmboxq, phba->fc_ratov * 2);
if (rc != MBX_SUCCESS) {
if (rc != MBX_TIMEOUT)
mempool_free(pmboxq, phba->mbox_mem_pool);
return NULL;
}
hs->link_failure_count = pmb->un.varRdLnk.linkFailureCnt;
hs->loss_of_sync_count = pmb->un.varRdLnk.lossSyncCnt;
hs->loss_of_signal_count = pmb->un.varRdLnk.lossSignalCnt;
hs->prim_seq_protocol_err_count = pmb->un.varRdLnk.primSeqErrCnt;
hs->invalid_tx_word_count = pmb->un.varRdLnk.invalidXmitWord;
hs->invalid_crc_count = pmb->un.varRdLnk.crcCnt;
hs->error_frames = pmb->un.varRdLnk.crcCnt;
hs->link_failure_count -= lso->link_failure_count;
hs->loss_of_sync_count -= lso->loss_of_sync_count;
hs->loss_of_signal_count -= lso->loss_of_signal_count;
hs->prim_seq_protocol_err_count -= lso->prim_seq_protocol_err_count;
hs->invalid_tx_word_count -= lso->invalid_tx_word_count;
hs->invalid_crc_count -= lso->invalid_crc_count;
hs->error_frames -= lso->error_frames;
if (phba->fc_topology == TOPOLOGY_LOOP) {
hs->lip_count = (phba->fc_eventTag >> 1);
hs->lip_count -= lso->link_events;
hs->nos_count = -1;
} else {
hs->lip_count = -1;
hs->nos_count = (phba->fc_eventTag >> 1);
hs->nos_count -= lso->link_events;
}
hs->dumped_frames = -1;
seconds = get_seconds();
if (seconds < psli->stats_start)
hs->seconds_since_last_reset = seconds +
((unsigned long)-1 - psli->stats_start);
else
hs->seconds_since_last_reset = seconds - psli->stats_start;
mempool_free(pmboxq, phba->mbox_mem_pool);
return hs;
}
static void
lpfc_reset_stats(struct Scsi_Host *shost)
{
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_hba *phba = vport->phba;
struct lpfc_sli *psli = &phba->sli;
struct lpfc_lnk_stat *lso = &psli->lnk_stat_offsets;
LPFC_MBOXQ_t *pmboxq;
MAILBOX_t *pmb;
int rc = 0;
if (phba->sli.sli_flag & LPFC_BLOCK_MGMT_IO)
return;
pmboxq = mempool_alloc(phba->mbox_mem_pool, GFP_KERNEL);
if (!pmboxq)
return;
memset(pmboxq, 0, sizeof(LPFC_MBOXQ_t));
pmb = &pmboxq->mb;
pmb->mbxCommand = MBX_READ_STATUS;
pmb->mbxOwner = OWN_HOST;
pmb->un.varWords[0] = 0x1; /* reset request */
pmboxq->context1 = NULL;
pmboxq->vport = vport;
if ((vport->fc_flag & FC_OFFLINE_MODE) ||
(!(psli->sli_flag & LPFC_SLI2_ACTIVE)))
rc = lpfc_sli_issue_mbox(phba, pmboxq, MBX_POLL);
else
rc = lpfc_sli_issue_mbox_wait(phba, pmboxq, phba->fc_ratov * 2);
if (rc != MBX_SUCCESS) {
if (rc != MBX_TIMEOUT)
mempool_free(pmboxq, phba->mbox_mem_pool);
return;
}
memset(pmboxq, 0, sizeof(LPFC_MBOXQ_t));
pmb->mbxCommand = MBX_READ_LNK_STAT;
pmb->mbxOwner = OWN_HOST;
pmboxq->context1 = NULL;
pmboxq->vport = vport;
if ((vport->fc_flag & FC_OFFLINE_MODE) ||
(!(psli->sli_flag & LPFC_SLI2_ACTIVE)))
rc = lpfc_sli_issue_mbox(phba, pmboxq, MBX_POLL);
else
rc = lpfc_sli_issue_mbox_wait(phba, pmboxq, phba->fc_ratov * 2);
if (rc != MBX_SUCCESS) {
if (rc != MBX_TIMEOUT)
mempool_free( pmboxq, phba->mbox_mem_pool);
return;
}
lso->link_failure_count = pmb->un.varRdLnk.linkFailureCnt;
lso->loss_of_sync_count = pmb->un.varRdLnk.lossSyncCnt;
lso->loss_of_signal_count = pmb->un.varRdLnk.lossSignalCnt;
lso->prim_seq_protocol_err_count = pmb->un.varRdLnk.primSeqErrCnt;
lso->invalid_tx_word_count = pmb->un.varRdLnk.invalidXmitWord;
lso->invalid_crc_count = pmb->un.varRdLnk.crcCnt;
lso->error_frames = pmb->un.varRdLnk.crcCnt;
lso->link_events = (phba->fc_eventTag >> 1);
psli->stats_start = get_seconds();
mempool_free(pmboxq, phba->mbox_mem_pool);
return;
}
/*
* The LPFC driver treats linkdown handling as target loss events so there
* are no sysfs handlers for link_down_tmo.
*/
static struct lpfc_nodelist *
lpfc_get_node_by_target(struct scsi_target *starget)
{
struct Scsi_Host *shost = dev_to_shost(starget->dev.parent);
struct lpfc_vport *vport = (struct lpfc_vport *) shost->hostdata;
struct lpfc_nodelist *ndlp;
spin_lock_irq(shost->host_lock);
/* Search for this, mapped, target ID */
list_for_each_entry(ndlp, &vport->fc_nodes, nlp_listp) {
if (NLP_CHK_NODE_ACT(ndlp) &&
ndlp->nlp_state == NLP_STE_MAPPED_NODE &&
starget->id == ndlp->nlp_sid) {
spin_unlock_irq(shost->host_lock);
return ndlp;
}
}
spin_unlock_irq(shost->host_lock);
return NULL;
}
static void
lpfc_get_starget_port_id(struct scsi_target *starget)
{
struct lpfc_nodelist *ndlp = lpfc_get_node_by_target(starget);
fc_starget_port_id(starget) = ndlp ? ndlp->nlp_DID : -1;
}
static void
lpfc_get_starget_node_name(struct scsi_target *starget)
{
struct lpfc_nodelist *ndlp = lpfc_get_node_by_target(starget);
fc_starget_node_name(starget) =
ndlp ? wwn_to_u64(ndlp->nlp_nodename.u.wwn) : 0;
}
static void
lpfc_get_starget_port_name(struct scsi_target *starget)
{
struct lpfc_nodelist *ndlp = lpfc_get_node_by_target(starget);
fc_starget_port_name(starget) =
ndlp ? wwn_to_u64(ndlp->nlp_portname.u.wwn) : 0;
}
static void
lpfc_set_rport_loss_tmo(struct fc_rport *rport, uint32_t timeout)
{
if (timeout)
rport->dev_loss_tmo = timeout;
else
rport->dev_loss_tmo = 1;
}
#define lpfc_rport_show_function(field, format_string, sz, cast) \
static ssize_t \
lpfc_show_rport_##field (struct device *dev, \
struct device_attribute *attr, \
char *buf) \
{ \
struct fc_rport *rport = transport_class_to_rport(dev); \
struct lpfc_rport_data *rdata = rport->hostdata; \
return snprintf(buf, sz, format_string, \
(rdata->target) ? cast rdata->target->field : 0); \
}
#define lpfc_rport_rd_attr(field, format_string, sz) \
lpfc_rport_show_function(field, format_string, sz, ) \
static FC_RPORT_ATTR(field, S_IRUGO, lpfc_show_rport_##field, NULL)
struct fc_function_template lpfc_transport_functions = {
/* fixed attributes the driver supports */
.show_host_node_name = 1,
.show_host_port_name = 1,
.show_host_supported_classes = 1,
.show_host_supported_fc4s = 1,
.show_host_supported_speeds = 1,
.show_host_maxframe_size = 1,
/* dynamic attributes the driver supports */
.get_host_port_id = lpfc_get_host_port_id,
.show_host_port_id = 1,
.get_host_port_type = lpfc_get_host_port_type,
.show_host_port_type = 1,
.get_host_port_state = lpfc_get_host_port_state,
.show_host_port_state = 1,
/* active_fc4s is shown but doesn't change (thus no get function) */
.show_host_active_fc4s = 1,
.get_host_speed = lpfc_get_host_speed,
.show_host_speed = 1,
.get_host_fabric_name = lpfc_get_host_fabric_name,
.show_host_fabric_name = 1,
/*
* The LPFC driver treats linkdown handling as target loss events
* so there are no sysfs handlers for link_down_tmo.
*/
.get_fc_host_stats = lpfc_get_stats,
.reset_fc_host_stats = lpfc_reset_stats,
.dd_fcrport_size = sizeof(struct lpfc_rport_data),
.show_rport_maxframe_size = 1,
.show_rport_supported_classes = 1,
.set_rport_dev_loss_tmo = lpfc_set_rport_loss_tmo,
.show_rport_dev_loss_tmo = 1,
.get_starget_port_id = lpfc_get_starget_port_id,
.show_starget_port_id = 1,
.get_starget_node_name = lpfc_get_starget_node_name,
.show_starget_node_name = 1,
.get_starget_port_name = lpfc_get_starget_port_name,
.show_starget_port_name = 1,
.issue_fc_host_lip = lpfc_issue_lip,
.dev_loss_tmo_callbk = lpfc_dev_loss_tmo_callbk,
.terminate_rport_io = lpfc_terminate_rport_io,
.dd_fcvport_size = sizeof(struct lpfc_vport *),
};
struct fc_function_template lpfc_vport_transport_functions = {
/* fixed attributes the driver supports */
.show_host_node_name = 1,
.show_host_port_name = 1,
.show_host_supported_classes = 1,
.show_host_supported_fc4s = 1,
.show_host_supported_speeds = 1,
.show_host_maxframe_size = 1,
/* dynamic attributes the driver supports */
.get_host_port_id = lpfc_get_host_port_id,
.show_host_port_id = 1,
.get_host_port_type = lpfc_get_host_port_type,
.show_host_port_type = 1,
.get_host_port_state = lpfc_get_host_port_state,
.show_host_port_state = 1,
/* active_fc4s is shown but doesn't change (thus no get function) */
.show_host_active_fc4s = 1,
.get_host_speed = lpfc_get_host_speed,
.show_host_speed = 1,
.get_host_fabric_name = lpfc_get_host_fabric_name,
.show_host_fabric_name = 1,
/*
* The LPFC driver treats linkdown handling as target loss events
* so there are no sysfs handlers for link_down_tmo.
*/
.get_fc_host_stats = lpfc_get_stats,
.reset_fc_host_stats = lpfc_reset_stats,
.dd_fcrport_size = sizeof(struct lpfc_rport_data),
.show_rport_maxframe_size = 1,
.show_rport_supported_classes = 1,
.set_rport_dev_loss_tmo = lpfc_set_rport_loss_tmo,
.show_rport_dev_loss_tmo = 1,
.get_starget_port_id = lpfc_get_starget_port_id,
.show_starget_port_id = 1,
.get_starget_node_name = lpfc_get_starget_node_name,
.show_starget_node_name = 1,
.get_starget_port_name = lpfc_get_starget_port_name,
.show_starget_port_name = 1,
.dev_loss_tmo_callbk = lpfc_dev_loss_tmo_callbk,
.terminate_rport_io = lpfc_terminate_rport_io,
.vport_disable = lpfc_vport_disable,
};
void
lpfc_get_cfgparam(struct lpfc_hba *phba)
{
lpfc_cr_delay_init(phba, lpfc_cr_delay);
lpfc_cr_count_init(phba, lpfc_cr_count);
lpfc_multi_ring_support_init(phba, lpfc_multi_ring_support);
lpfc_multi_ring_rctl_init(phba, lpfc_multi_ring_rctl);
lpfc_multi_ring_type_init(phba, lpfc_multi_ring_type);
lpfc_ack0_init(phba, lpfc_ack0);
lpfc_topology_init(phba, lpfc_topology);
lpfc_link_speed_init(phba, lpfc_link_speed);
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
lpfc_poll_tmo_init(phba, lpfc_poll_tmo);
lpfc_enable_npiv_init(phba, lpfc_enable_npiv);
lpfc_use_msi_init(phba, lpfc_use_msi);
lpfc_enable_hba_reset_init(phba, lpfc_enable_hba_reset);
lpfc_enable_hba_heartbeat_init(phba, lpfc_enable_hba_heartbeat);
[SCSI] lpfc 8.1.1 : Add polled-mode support - Add functionality to run in polled mode only. Includes run time attribute to enable mode. - Enable runtime writable hba settings for coallescing and delay parameters Customers have requested a mode in the driver to run strictly polled. This is generally to support an environment where the server is extremely loaded and is looking to reclaim some cpu cycles from adapter interrupt handling. This patch adds a new "poll" attribute, and the following behavior: if value is 0 (default): The driver uses the normal method for i/o completion. It uses the firmware feature of interrupt coalesing. The firmware allows a minimum number of i/o completions before an interrupt, or a maximum time delay between interrupts. By default, the driver sets these to no delay (disabled) or 1 i/o - meaning coalescing is disabled. Attributes were provided to change the coalescing values, but it was a module-load time only and global across all adapters. This patch allows them to be writable on a per-adapter basis. if value is 1 : Interrupts are left enabled, expecting that the user has tuned the interrupt coalescing values. When this setting is enabled, the driver will attempt to service completed i/o whenever new i/o is submitted to the adapter. If the coalescing values are large, and the i/o generation rate steady, an interrupt will be avoided by servicing completed i/o prior to the coalescing thresholds kicking in. However, if the i/o completion load is high enough or i/o generation slow, the coalescion values will ensure that completed i/o is serviced in a timely fashion. if value is 3 : Turns off FCP i/o interrupts altogether. The coalescing values now have no effect. A new attribute "poll_tmo" (default 10ms) exists to set the polling interval for i/o completion. When this setting is enabled, the driver will attempt to service completed i/o and restart the interval timer whenever new i/o is submitted. This behavior allows for servicing of completed i/o sooner than the interval timer, but ensures that if no i/o is being issued, then the interval timer will kick in to service the outstanding i/o. Signed-off-by: James Smart <James.Smart@emulex.com> Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
2005-11-29 16:32:13 -05:00
phba->cfg_poll = lpfc_poll;
phba->cfg_soft_wwnn = 0L;
phba->cfg_soft_wwpn = 0L;
lpfc_sg_seg_cnt_init(phba, lpfc_sg_seg_cnt);
/* Also reinitialize the host templates with new values. */
lpfc_vport_template.sg_tablesize = phba->cfg_sg_seg_cnt;
lpfc_template.sg_tablesize = phba->cfg_sg_seg_cnt;
/*
* Since the sg_tablesize is module parameter, the sg_dma_buf_size
* used to create the sg_dma_buf_pool must be dynamically calculated.
* 2 segments are added since the IOCB needs a command and response bde.
*/
phba->cfg_sg_dma_buf_size = sizeof(struct fcp_cmnd) +
sizeof(struct fcp_rsp) +
((phba->cfg_sg_seg_cnt + 2) * sizeof(struct ulp_bde64));
lpfc_hba_queue_depth_init(phba, lpfc_hba_queue_depth);
return;
}
void
lpfc_get_vport_cfgparam(struct lpfc_vport *vport)
{
lpfc_log_verbose_init(vport, lpfc_log_verbose);
lpfc_lun_queue_depth_init(vport, lpfc_lun_queue_depth);
lpfc_devloss_tmo_init(vport, lpfc_devloss_tmo);
lpfc_nodev_tmo_init(vport, lpfc_nodev_tmo);
lpfc_peer_port_login_init(vport, lpfc_peer_port_login);
lpfc_restrict_login_init(vport, lpfc_restrict_login);
lpfc_fcp_class_init(vport, lpfc_fcp_class);
lpfc_use_adisc_init(vport, lpfc_use_adisc);
lpfc_fdmi_on_init(vport, lpfc_fdmi_on);
lpfc_discovery_threads_init(vport, lpfc_discovery_threads);
lpfc_max_luns_init(vport, lpfc_max_luns);
lpfc_scan_down_init(vport, lpfc_scan_down);
lpfc_enable_da_id_init(vport, lpfc_enable_da_id);
return;
}