2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/*******************************************************************************
|
|
|
|
*
|
|
|
|
* Module Name: hwregs - Read/write access functions for the various ACPI
|
|
|
|
* control and status registers.
|
|
|
|
*
|
|
|
|
******************************************************************************/
|
|
|
|
|
|
|
|
/*
|
2006-01-13 16:22:00 -05:00
|
|
|
* Copyright (C) 2000 - 2006, R. Byron Moore
|
2005-04-16 18:20:36 -04:00
|
|
|
* All rights reserved.
|
|
|
|
*
|
|
|
|
* Redistribution and use in source and binary forms, with or without
|
|
|
|
* modification, are permitted provided that the following conditions
|
|
|
|
* are met:
|
|
|
|
* 1. Redistributions of source code must retain the above copyright
|
|
|
|
* notice, this list of conditions, and the following disclaimer,
|
|
|
|
* without modification.
|
|
|
|
* 2. Redistributions in binary form must reproduce at minimum a disclaimer
|
|
|
|
* substantially similar to the "NO WARRANTY" disclaimer below
|
|
|
|
* ("Disclaimer") and any redistribution must be conditioned upon
|
|
|
|
* including a substantially similar Disclaimer requirement for further
|
|
|
|
* binary redistribution.
|
|
|
|
* 3. Neither the names of the above-listed copyright holders nor the names
|
|
|
|
* of any contributors may be used to endorse or promote products derived
|
|
|
|
* from this software without specific prior written permission.
|
|
|
|
*
|
|
|
|
* Alternatively, this software may be distributed under the terms of the
|
|
|
|
* GNU General Public License ("GPL") version 2 as published by the Free
|
|
|
|
* Software Foundation.
|
|
|
|
*
|
|
|
|
* NO WARRANTY
|
|
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
|
|
|
|
* "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
|
|
|
|
* LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTIBILITY AND FITNESS FOR
|
|
|
|
* A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
|
|
|
|
* HOLDERS OR CONTRIBUTORS BE LIABLE FOR SPECIAL, EXEMPLARY, OR CONSEQUENTIAL
|
|
|
|
* DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS
|
|
|
|
* OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION)
|
|
|
|
* HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT,
|
|
|
|
* STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING
|
|
|
|
* IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
|
|
|
|
* POSSIBILITY OF SUCH DAMAGES.
|
|
|
|
*/
|
|
|
|
|
|
|
|
#include <acpi/acpi.h>
|
|
|
|
#include <acpi/acnamesp.h>
|
|
|
|
#include <acpi/acevents.h>
|
|
|
|
|
|
|
|
#define _COMPONENT ACPI_HARDWARE
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_MODULE_NAME("hwregs")
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/*******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_hw_clear_acpi_status
|
|
|
|
*
|
|
|
|
* PARAMETERS: Flags - Lock the hardware or not
|
|
|
|
*
|
|
|
|
* RETURN: none
|
|
|
|
*
|
|
|
|
* DESCRIPTION: Clears all fixed and general purpose status bits
|
|
|
|
* THIS FUNCTION MUST BE CALLED WITH INTERRUPTS DISABLED
|
|
|
|
*
|
2006-06-08 16:29:00 -04:00
|
|
|
* NOTE: TBD: Flags parameter is obsolete, to be removed
|
|
|
|
*
|
2005-04-16 18:20:36 -04:00
|
|
|
******************************************************************************/
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_status acpi_hw_clear_acpi_status(u32 flags)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_status status;
|
2006-06-08 16:29:00 -04:00
|
|
|
acpi_cpu_flags lock_flags = 0;
|
2005-04-16 18:20:36 -04:00
|
|
|
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_FUNCTION_TRACE(hw_clear_acpi_status);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_IO, "About to write %04X to %04X\n",
|
|
|
|
ACPI_BITMASK_ALL_FIXED_STATUS,
|
|
|
|
(u16) acpi_gbl_FADT->xpm1a_evt_blk.address));
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2006-06-08 16:29:00 -04:00
|
|
|
lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_hw_register_write(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
ACPI_REGISTER_PM1_STATUS,
|
|
|
|
ACPI_BITMASK_ALL_FIXED_STATUS);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Clear the fixed events */
|
|
|
|
|
|
|
|
if (acpi_gbl_FADT->xpm1b_evt_blk.address) {
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, ACPI_BITMASK_ALL_FIXED_STATUS,
|
|
|
|
&acpi_gbl_FADT->xpm1b_evt_blk);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Clear the GPE Bits in all GPE registers in all GPE blocks */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_ev_walk_gpe_list(acpi_hw_clear_gpe_block);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
unlock_and_exit:
|
2006-06-08 16:29:00 -04:00
|
|
|
acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags);
|
2005-08-05 00:44:28 -04:00
|
|
|
return_ACPI_STATUS(status);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
|
|
|
/*******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_get_sleep_type_data
|
|
|
|
*
|
|
|
|
* PARAMETERS: sleep_state - Numeric sleep state
|
|
|
|
* *sleep_type_a - Where SLP_TYPa is returned
|
|
|
|
* *sleep_type_b - Where SLP_TYPb is returned
|
|
|
|
*
|
|
|
|
* RETURN: Status - ACPI status
|
|
|
|
*
|
|
|
|
* DESCRIPTION: Obtain the SLP_TYPa and SLP_TYPb values for the requested sleep
|
|
|
|
* state.
|
|
|
|
*
|
|
|
|
******************************************************************************/
|
|
|
|
|
|
|
|
acpi_status
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_get_sleep_type_data(u8 sleep_state, u8 * sleep_type_a, u8 * sleep_type_b)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_status status = AE_OK;
|
2006-05-26 16:36:00 -04:00
|
|
|
struct acpi_evaluate_info *info;
|
2005-04-16 18:20:36 -04:00
|
|
|
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_FUNCTION_TRACE(acpi_get_sleep_type_data);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-04-18 22:49:35 -04:00
|
|
|
/* Validate parameters */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
if ((sleep_state > ACPI_S_STATES_MAX) || !sleep_type_a || !sleep_type_b) {
|
|
|
|
return_ACPI_STATUS(AE_BAD_PARAMETER);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2006-05-26 16:36:00 -04:00
|
|
|
/* Allocate the evaluation information block */
|
|
|
|
|
|
|
|
info = ACPI_ALLOCATE_ZEROED(sizeof(struct acpi_evaluate_info));
|
|
|
|
if (!info) {
|
|
|
|
return_ACPI_STATUS(AE_NO_MEMORY);
|
|
|
|
}
|
2005-04-18 22:49:35 -04:00
|
|
|
|
2006-05-26 16:36:00 -04:00
|
|
|
info->pathname =
|
2005-12-16 17:05:00 -05:00
|
|
|
ACPI_CAST_PTR(char, acpi_gbl_sleep_state_names[sleep_state]);
|
2005-04-18 22:49:35 -04:00
|
|
|
|
2006-05-26 16:36:00 -04:00
|
|
|
/* Evaluate the namespace object containing the values for this state */
|
|
|
|
|
|
|
|
status = acpi_ns_evaluate(info);
|
2005-08-05 00:44:28 -04:00
|
|
|
if (ACPI_FAILURE(status)) {
|
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_EXEC,
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
"%s while evaluating SleepState [%s]\n",
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_format_exception(status),
|
2006-05-26 16:36:00 -04:00
|
|
|
info->pathname));
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2006-05-26 16:36:00 -04:00
|
|
|
goto cleanup;
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
|
|
|
/* Must have a return object */
|
|
|
|
|
2006-05-26 16:36:00 -04:00
|
|
|
if (!info->return_object) {
|
2006-01-27 16:43:00 -05:00
|
|
|
ACPI_ERROR((AE_INFO, "No Sleep State object returned from [%s]",
|
2006-05-26 16:36:00 -04:00
|
|
|
info->pathname));
|
2005-04-16 18:20:36 -04:00
|
|
|
status = AE_NOT_EXIST;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* It must be of type Package */
|
|
|
|
|
2006-05-26 16:36:00 -04:00
|
|
|
else if (ACPI_GET_OBJECT_TYPE(info->return_object) != ACPI_TYPE_PACKAGE) {
|
2006-01-27 16:43:00 -05:00
|
|
|
ACPI_ERROR((AE_INFO,
|
|
|
|
"Sleep State return object is not a Package"));
|
2005-04-16 18:20:36 -04:00
|
|
|
status = AE_AML_OPERAND_TYPE;
|
|
|
|
}
|
|
|
|
|
2005-04-18 22:49:35 -04:00
|
|
|
/*
|
2006-06-23 17:04:00 -04:00
|
|
|
* The package must have at least two elements. NOTE (March 2005): This
|
2005-04-18 22:49:35 -04:00
|
|
|
* goes against the current ACPI spec which defines this object as a
|
2006-06-23 17:04:00 -04:00
|
|
|
* package with one encoded DWORD element. However, existing practice
|
2005-04-18 22:49:35 -04:00
|
|
|
* by BIOS vendors seems to be to have 2 or more elements, at least
|
|
|
|
* one per sleep type (A/B).
|
|
|
|
*/
|
2006-05-26 16:36:00 -04:00
|
|
|
else if (info->return_object->package.count < 2) {
|
2006-01-27 16:43:00 -05:00
|
|
|
ACPI_ERROR((AE_INFO,
|
|
|
|
"Sleep State return package does not have at least two elements"));
|
2005-04-16 18:20:36 -04:00
|
|
|
status = AE_AML_NO_OPERAND;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* The first two elements must both be of type Integer */
|
|
|
|
|
2006-05-26 16:36:00 -04:00
|
|
|
else if ((ACPI_GET_OBJECT_TYPE(info->return_object->package.elements[0])
|
2005-08-05 00:44:28 -04:00
|
|
|
!= ACPI_TYPE_INTEGER) ||
|
2006-05-26 16:36:00 -04:00
|
|
|
(ACPI_GET_OBJECT_TYPE(info->return_object->package.elements[1])
|
2005-08-05 00:44:28 -04:00
|
|
|
!= ACPI_TYPE_INTEGER)) {
|
2006-01-27 16:43:00 -05:00
|
|
|
ACPI_ERROR((AE_INFO,
|
|
|
|
"Sleep State return package elements are not both Integers (%s, %s)",
|
2006-05-26 16:36:00 -04:00
|
|
|
acpi_ut_get_object_type_name(info->return_object->
|
2006-01-27 16:43:00 -05:00
|
|
|
package.elements[0]),
|
2006-05-26 16:36:00 -04:00
|
|
|
acpi_ut_get_object_type_name(info->return_object->
|
2006-01-27 16:43:00 -05:00
|
|
|
package.elements[1])));
|
2005-04-16 18:20:36 -04:00
|
|
|
status = AE_AML_OPERAND_TYPE;
|
2005-08-05 00:44:28 -04:00
|
|
|
} else {
|
2005-04-18 22:49:35 -04:00
|
|
|
/* Valid _Sx_ package size, type, and value */
|
|
|
|
|
|
|
|
*sleep_type_a = (u8)
|
2006-05-26 16:36:00 -04:00
|
|
|
(info->return_object->package.elements[0])->integer.value;
|
2005-04-18 22:49:35 -04:00
|
|
|
*sleep_type_b = (u8)
|
2006-05-26 16:36:00 -04:00
|
|
|
(info->return_object->package.elements[1])->integer.value;
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
if (ACPI_FAILURE(status)) {
|
2006-01-27 16:43:00 -05:00
|
|
|
ACPI_EXCEPTION((AE_INFO, status,
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
"While evaluating SleepState [%s], bad Sleep object %p type %s",
|
2006-05-26 16:36:00 -04:00
|
|
|
info->pathname, info->return_object,
|
|
|
|
acpi_ut_get_object_type_name(info->
|
2006-01-27 16:43:00 -05:00
|
|
|
return_object)));
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2006-05-26 16:36:00 -04:00
|
|
|
acpi_ut_remove_reference(info->return_object);
|
|
|
|
|
|
|
|
cleanup:
|
|
|
|
ACPI_FREE(info);
|
2005-08-05 00:44:28 -04:00
|
|
|
return_ACPI_STATUS(status);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2006-10-03 00:00:00 -04:00
|
|
|
ACPI_EXPORT_SYMBOL(acpi_get_sleep_type_data)
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/*******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_hw_get_register_bit_mask
|
|
|
|
*
|
|
|
|
* PARAMETERS: register_id - Index of ACPI Register to access
|
|
|
|
*
|
2005-04-18 22:49:35 -04:00
|
|
|
* RETURN: The bitmask to be used when accessing the register
|
2005-04-16 18:20:36 -04:00
|
|
|
*
|
2005-04-18 22:49:35 -04:00
|
|
|
* DESCRIPTION: Map register_id into a register bitmask.
|
2005-04-16 18:20:36 -04:00
|
|
|
*
|
|
|
|
******************************************************************************/
|
2005-08-05 00:44:28 -04:00
|
|
|
struct acpi_bit_register_info *acpi_hw_get_bit_register_info(u32 register_id)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2006-01-13 16:22:00 -05:00
|
|
|
ACPI_FUNCTION_ENTRY();
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
if (register_id > ACPI_BITREG_MAX) {
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_ERROR((AE_INFO, "Invalid BitRegister ID: %X",
|
2006-01-27 16:43:00 -05:00
|
|
|
register_id));
|
2005-04-16 18:20:36 -04:00
|
|
|
return (NULL);
|
|
|
|
}
|
|
|
|
|
|
|
|
return (&acpi_gbl_bit_register_info[register_id]);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_get_register
|
|
|
|
*
|
|
|
|
* PARAMETERS: register_id - ID of ACPI bit_register to access
|
|
|
|
* return_value - Value that was read from the register
|
|
|
|
* Flags - Lock the hardware or not
|
|
|
|
*
|
2006-06-23 17:04:00 -04:00
|
|
|
* RETURN: Status and the value read from specified Register. Value
|
2005-04-16 18:20:36 -04:00
|
|
|
* returned is normalized to bit0 (is shifted all the way right)
|
|
|
|
*
|
|
|
|
* DESCRIPTION: ACPI bit_register read function.
|
|
|
|
*
|
2006-06-08 16:29:00 -04:00
|
|
|
* NOTE: TBD: Flags parameter is obsolete, to be removed
|
|
|
|
*
|
2005-04-16 18:20:36 -04:00
|
|
|
******************************************************************************/
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_status acpi_get_register(u32 register_id, u32 * return_value, u32 flags)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2005-08-05 00:44:28 -04:00
|
|
|
u32 register_value = 0;
|
|
|
|
struct acpi_bit_register_info *bit_reg_info;
|
|
|
|
acpi_status status;
|
2005-04-16 18:20:36 -04:00
|
|
|
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_FUNCTION_TRACE(acpi_get_register);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/* Get the info structure corresponding to the requested ACPI Register */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
bit_reg_info = acpi_hw_get_bit_register_info(register_id);
|
2005-04-16 18:20:36 -04:00
|
|
|
if (!bit_reg_info) {
|
2005-08-05 00:44:28 -04:00
|
|
|
return_ACPI_STATUS(AE_BAD_PARAMETER);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
|
|
|
/* Read from the register */
|
|
|
|
|
2006-06-08 16:29:00 -04:00
|
|
|
status = acpi_hw_register_read(ACPI_MTX_LOCK,
|
2005-08-05 00:44:28 -04:00
|
|
|
bit_reg_info->parent_register,
|
|
|
|
®ister_value);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
if (ACPI_SUCCESS(status)) {
|
2006-10-02 00:00:00 -04:00
|
|
|
|
2005-04-16 18:20:36 -04:00
|
|
|
/* Normalize the value that was read */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
register_value =
|
|
|
|
((register_value & bit_reg_info->access_bit_mask)
|
|
|
|
>> bit_reg_info->bit_position);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
*return_value = register_value;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_IO, "Read value %8.8X register %X\n",
|
|
|
|
register_value,
|
|
|
|
bit_reg_info->parent_register));
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
return_ACPI_STATUS(status);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2006-10-03 00:00:00 -04:00
|
|
|
ACPI_EXPORT_SYMBOL(acpi_get_register)
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/*******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_set_register
|
|
|
|
*
|
|
|
|
* PARAMETERS: register_id - ID of ACPI bit_register to access
|
|
|
|
* Value - (only used on write) value to write to the
|
|
|
|
* Register, NOT pre-normalized to the bit pos
|
|
|
|
* Flags - Lock the hardware or not
|
|
|
|
*
|
|
|
|
* RETURN: Status
|
|
|
|
*
|
|
|
|
* DESCRIPTION: ACPI Bit Register write function.
|
|
|
|
*
|
2006-06-08 16:29:00 -04:00
|
|
|
* NOTE: TBD: Flags parameter is obsolete, to be removed
|
|
|
|
*
|
2005-04-16 18:20:36 -04:00
|
|
|
******************************************************************************/
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_status acpi_set_register(u32 register_id, u32 value, u32 flags)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2005-08-05 00:44:28 -04:00
|
|
|
u32 register_value = 0;
|
|
|
|
struct acpi_bit_register_info *bit_reg_info;
|
|
|
|
acpi_status status;
|
2006-06-08 16:29:00 -04:00
|
|
|
acpi_cpu_flags lock_flags;
|
2005-04-16 18:20:36 -04:00
|
|
|
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_FUNCTION_TRACE_U32(acpi_set_register, register_id);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/* Get the info structure corresponding to the requested ACPI Register */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
bit_reg_info = acpi_hw_get_bit_register_info(register_id);
|
2005-04-16 18:20:36 -04:00
|
|
|
if (!bit_reg_info) {
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_ERROR((AE_INFO, "Bad ACPI HW RegisterId: %X",
|
2006-01-27 16:43:00 -05:00
|
|
|
register_id));
|
2005-08-05 00:44:28 -04:00
|
|
|
return_ACPI_STATUS(AE_BAD_PARAMETER);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2006-06-08 16:29:00 -04:00
|
|
|
lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/* Always do a register read first so we can insert the new bits */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_hw_register_read(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
bit_reg_info->parent_register,
|
|
|
|
®ister_value);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Decode the Register ID
|
|
|
|
* Register ID = [Register block ID] | [bit ID]
|
|
|
|
*
|
|
|
|
* Check bit ID to fine locate Register offset.
|
|
|
|
* Check Mask to determine Register offset, and then read-write.
|
|
|
|
*/
|
|
|
|
switch (bit_reg_info->parent_register) {
|
|
|
|
case ACPI_REGISTER_PM1_STATUS:
|
|
|
|
|
|
|
|
/*
|
2006-06-23 17:04:00 -04:00
|
|
|
* Status Registers are different from the rest. Clear by
|
|
|
|
* writing 1, and writing 0 has no effect. So, the only relevant
|
2005-04-16 18:20:36 -04:00
|
|
|
* information is the single bit we're interested in, all others should
|
|
|
|
* be written as 0 so they will be left unchanged.
|
|
|
|
*/
|
2005-08-05 00:44:28 -04:00
|
|
|
value = ACPI_REGISTER_PREPARE_BITS(value,
|
|
|
|
bit_reg_info->bit_position,
|
|
|
|
bit_reg_info->
|
|
|
|
access_bit_mask);
|
2005-04-16 18:20:36 -04:00
|
|
|
if (value) {
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_hw_register_write(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
ACPI_REGISTER_PM1_STATUS,
|
|
|
|
(u16) value);
|
2005-04-16 18:20:36 -04:00
|
|
|
register_value = 0;
|
|
|
|
}
|
|
|
|
break;
|
|
|
|
|
|
|
|
case ACPI_REGISTER_PM1_ENABLE:
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_REGISTER_INSERT_VALUE(register_value,
|
|
|
|
bit_reg_info->bit_position,
|
|
|
|
bit_reg_info->access_bit_mask,
|
|
|
|
value);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_hw_register_write(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
ACPI_REGISTER_PM1_ENABLE,
|
|
|
|
(u16) register_value);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
case ACPI_REGISTER_PM1_CONTROL:
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Write the PM1 Control register.
|
|
|
|
* Note that at this level, the fact that there are actually TWO
|
|
|
|
* registers (A and B - and B may not exist) is abstracted.
|
|
|
|
*/
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_IO, "PM1 control: Read %X\n",
|
|
|
|
register_value));
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_REGISTER_INSERT_VALUE(register_value,
|
|
|
|
bit_reg_info->bit_position,
|
|
|
|
bit_reg_info->access_bit_mask,
|
|
|
|
value);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_hw_register_write(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
ACPI_REGISTER_PM1_CONTROL,
|
|
|
|
(u16) register_value);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
case ACPI_REGISTER_PM2_CONTROL:
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_hw_register_read(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
ACPI_REGISTER_PM2_CONTROL,
|
|
|
|
®ister_value);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_IO,
|
|
|
|
"PM2 control: Read %X from %8.8X%8.8X\n",
|
|
|
|
register_value,
|
|
|
|
ACPI_FORMAT_UINT64(acpi_gbl_FADT->
|
|
|
|
xpm2_cnt_blk.address)));
|
|
|
|
|
|
|
|
ACPI_REGISTER_INSERT_VALUE(register_value,
|
|
|
|
bit_reg_info->bit_position,
|
|
|
|
bit_reg_info->access_bit_mask,
|
|
|
|
value);
|
|
|
|
|
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_IO,
|
|
|
|
"About to write %4.4X to %8.8X%8.8X\n",
|
|
|
|
register_value,
|
|
|
|
ACPI_FORMAT_UINT64(acpi_gbl_FADT->
|
|
|
|
xpm2_cnt_blk.address)));
|
|
|
|
|
|
|
|
status = acpi_hw_register_write(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
ACPI_REGISTER_PM2_CONTROL,
|
|
|
|
(u8) (register_value));
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
default:
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
unlock_and_exit:
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2006-06-08 16:29:00 -04:00
|
|
|
acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/* Normalize the value that was read */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_DEBUG_EXEC(register_value =
|
|
|
|
((register_value & bit_reg_info->access_bit_mask) >>
|
|
|
|
bit_reg_info->bit_position));
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_IO,
|
|
|
|
"Set bits: %8.8X actual %8.8X register %X\n", value,
|
|
|
|
register_value, bit_reg_info->parent_register));
|
|
|
|
return_ACPI_STATUS(status);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2006-10-03 00:00:00 -04:00
|
|
|
ACPI_EXPORT_SYMBOL(acpi_set_register)
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_hw_register_read
|
|
|
|
*
|
2006-06-23 17:04:00 -04:00
|
|
|
* PARAMETERS: use_lock - Lock hardware? True/False
|
|
|
|
* register_id - ACPI Register ID
|
2005-04-18 22:49:35 -04:00
|
|
|
* return_value - Where the register value is returned
|
2005-04-16 18:20:36 -04:00
|
|
|
*
|
|
|
|
* RETURN: Status and the value read.
|
|
|
|
*
|
2006-06-23 17:04:00 -04:00
|
|
|
* DESCRIPTION: Read from the specified ACPI register
|
2005-04-16 18:20:36 -04:00
|
|
|
*
|
|
|
|
******************************************************************************/
|
|
|
|
acpi_status
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_hw_register_read(u8 use_lock, u32 register_id, u32 * return_value)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2005-08-05 00:44:28 -04:00
|
|
|
u32 value1 = 0;
|
|
|
|
u32 value2 = 0;
|
|
|
|
acpi_status status;
|
2006-06-08 16:29:00 -04:00
|
|
|
acpi_cpu_flags lock_flags = 0;
|
2005-04-16 18:20:36 -04:00
|
|
|
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_FUNCTION_TRACE(hw_register_read);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
if (ACPI_MTX_LOCK == use_lock) {
|
2006-06-08 16:29:00 -04:00
|
|
|
lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
|
|
|
switch (register_id) {
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM1_STATUS: /* 16-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_read(16, &value1,
|
|
|
|
&acpi_gbl_FADT->xpm1a_evt_blk);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* PM1B is optional */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_read(16, &value2,
|
|
|
|
&acpi_gbl_FADT->xpm1b_evt_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
value1 |= value2;
|
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM1_ENABLE: /* 16-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_read(16, &value1, &acpi_gbl_xpm1a_enable);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* PM1B is optional */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_read(16, &value2, &acpi_gbl_xpm1b_enable);
|
2005-04-16 18:20:36 -04:00
|
|
|
value1 |= value2;
|
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM1_CONTROL: /* 16-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_read(16, &value1,
|
|
|
|
&acpi_gbl_FADT->xpm1a_cnt_blk);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_read(16, &value2,
|
|
|
|
&acpi_gbl_FADT->xpm1b_cnt_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
value1 |= value2;
|
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM2_CONTROL: /* 8-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_read(8, &value1,
|
|
|
|
&acpi_gbl_FADT->xpm2_cnt_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM_TIMER: /* 32-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_read(32, &value1,
|
|
|
|
&acpi_gbl_FADT->xpm_tmr_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_SMI_COMMAND_BLOCK: /* 8-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_os_read_port(acpi_gbl_FADT->smi_cmd, &value1, 8);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
default:
|
2006-01-27 16:43:00 -05:00
|
|
|
ACPI_ERROR((AE_INFO, "Unknown Register ID: %X", register_id));
|
2005-04-16 18:20:36 -04:00
|
|
|
status = AE_BAD_PARAMETER;
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
unlock_and_exit:
|
2005-04-16 18:20:36 -04:00
|
|
|
if (ACPI_MTX_LOCK == use_lock) {
|
2006-06-08 16:29:00 -04:00
|
|
|
acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
if (ACPI_SUCCESS(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
*return_value = value1;
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
return_ACPI_STATUS(status);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
|
|
|
/******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_hw_register_write
|
|
|
|
*
|
2006-06-23 17:04:00 -04:00
|
|
|
* PARAMETERS: use_lock - Lock hardware? True/False
|
|
|
|
* register_id - ACPI Register ID
|
2005-04-16 18:20:36 -04:00
|
|
|
* Value - The value to write
|
|
|
|
*
|
|
|
|
* RETURN: Status
|
|
|
|
*
|
2006-06-23 17:04:00 -04:00
|
|
|
* DESCRIPTION: Write to the specified ACPI register
|
|
|
|
*
|
|
|
|
* NOTE: In accordance with the ACPI specification, this function automatically
|
|
|
|
* preserves the value of the following bits, meaning that these bits cannot be
|
|
|
|
* changed via this interface:
|
|
|
|
*
|
|
|
|
* PM1_CONTROL[0] = SCI_EN
|
|
|
|
* PM1_CONTROL[9]
|
|
|
|
* PM1_STATUS[11]
|
|
|
|
*
|
|
|
|
* ACPI References:
|
|
|
|
* 1) Hardware Ignored Bits: When software writes to a register with ignored
|
|
|
|
* bit fields, it preserves the ignored bit fields
|
|
|
|
* 2) SCI_EN: OSPM always preserves this bit position
|
2005-04-16 18:20:36 -04:00
|
|
|
*
|
|
|
|
******************************************************************************/
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_status acpi_hw_register_write(u8 use_lock, u32 register_id, u32 value)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_status status;
|
2006-06-08 16:29:00 -04:00
|
|
|
acpi_cpu_flags lock_flags = 0;
|
2006-06-23 17:04:00 -04:00
|
|
|
u32 read_value;
|
2005-04-16 18:20:36 -04:00
|
|
|
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_FUNCTION_TRACE(hw_register_write);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
if (ACPI_MTX_LOCK == use_lock) {
|
2006-06-08 16:29:00 -04:00
|
|
|
lock_flags = acpi_os_acquire_lock(acpi_gbl_hardware_lock);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
|
|
|
switch (register_id) {
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM1_STATUS: /* 16-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2006-06-23 17:04:00 -04:00
|
|
|
/* Perform a read first to preserve certain bits (per ACPI spec) */
|
|
|
|
|
|
|
|
status = acpi_hw_register_read(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
ACPI_REGISTER_PM1_STATUS,
|
|
|
|
&read_value);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Insert the bits to be preserved */
|
|
|
|
|
|
|
|
ACPI_INSERT_BITS(value, ACPI_PM1_STATUS_PRESERVED_BITS,
|
|
|
|
read_value);
|
|
|
|
|
|
|
|
/* Now we can write the data */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, value,
|
|
|
|
&acpi_gbl_FADT->xpm1a_evt_blk);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* PM1B is optional */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, value,
|
|
|
|
&acpi_gbl_FADT->xpm1b_evt_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM1_ENABLE: /* 16-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, value, &acpi_gbl_xpm1a_enable);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* PM1B is optional */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, value, &acpi_gbl_xpm1b_enable);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM1_CONTROL: /* 16-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2006-06-23 17:04:00 -04:00
|
|
|
/*
|
|
|
|
* Perform a read first to preserve certain bits (per ACPI spec)
|
|
|
|
*/
|
|
|
|
status = acpi_hw_register_read(ACPI_MTX_DO_NOT_LOCK,
|
|
|
|
ACPI_REGISTER_PM1_CONTROL,
|
|
|
|
&read_value);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
|
|
|
/* Insert the bits to be preserved */
|
|
|
|
|
|
|
|
ACPI_INSERT_BITS(value, ACPI_PM1_CONTROL_PRESERVED_BITS,
|
|
|
|
read_value);
|
|
|
|
|
|
|
|
/* Now we can write the data */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, value,
|
|
|
|
&acpi_gbl_FADT->xpm1a_cnt_blk);
|
|
|
|
if (ACPI_FAILURE(status)) {
|
2005-04-16 18:20:36 -04:00
|
|
|
goto unlock_and_exit;
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, value,
|
|
|
|
&acpi_gbl_FADT->xpm1b_cnt_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM1A_CONTROL: /* 16-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, value,
|
|
|
|
&acpi_gbl_FADT->xpm1a_cnt_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM1B_CONTROL: /* 16-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(16, value,
|
|
|
|
&acpi_gbl_FADT->xpm1b_cnt_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM2_CONTROL: /* 8-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(8, value,
|
|
|
|
&acpi_gbl_FADT->xpm2_cnt_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_PM_TIMER: /* 32-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status =
|
|
|
|
acpi_hw_low_level_write(32, value,
|
|
|
|
&acpi_gbl_FADT->xpm_tmr_blk);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
case ACPI_REGISTER_SMI_COMMAND_BLOCK: /* 8-bit access */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/* SMI_CMD is currently always in IO space */
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_os_write_port(acpi_gbl_FADT->smi_cmd, value, 8);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
default:
|
|
|
|
status = AE_BAD_PARAMETER;
|
|
|
|
break;
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
unlock_and_exit:
|
2005-04-16 18:20:36 -04:00
|
|
|
if (ACPI_MTX_LOCK == use_lock) {
|
2006-06-08 16:29:00 -04:00
|
|
|
acpi_os_release_lock(acpi_gbl_hardware_lock, lock_flags);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
return_ACPI_STATUS(status);
|
2005-04-16 18:20:36 -04:00
|
|
|
}
|
|
|
|
|
|
|
|
/******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_hw_low_level_read
|
|
|
|
*
|
|
|
|
* PARAMETERS: Width - 8, 16, or 32
|
|
|
|
* Value - Where the value is returned
|
|
|
|
* Reg - GAS register structure
|
|
|
|
*
|
|
|
|
* RETURN: Status
|
|
|
|
*
|
|
|
|
* DESCRIPTION: Read from either memory or IO space.
|
|
|
|
*
|
|
|
|
******************************************************************************/
|
|
|
|
|
|
|
|
acpi_status
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_hw_low_level_read(u32 width, u32 * value, struct acpi_generic_address *reg)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2005-08-05 00:44:28 -04:00
|
|
|
u64 address;
|
|
|
|
acpi_status status;
|
2005-04-16 18:20:36 -04:00
|
|
|
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_FUNCTION_NAME(hw_low_level_read);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Must have a valid pointer to a GAS structure, and
|
|
|
|
* a non-zero address within. However, don't return an error
|
|
|
|
* because the PM1A/B code must not fail if B isn't present.
|
|
|
|
*/
|
|
|
|
if (!reg) {
|
|
|
|
return (AE_OK);
|
|
|
|
}
|
|
|
|
|
2006-06-23 17:04:00 -04:00
|
|
|
/* Get a local copy of the address. Handles possible alignment issues */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_MOVE_64_TO_64(&address, ®->address);
|
2005-04-16 18:20:36 -04:00
|
|
|
if (!address) {
|
|
|
|
return (AE_OK);
|
|
|
|
}
|
|
|
|
*value = 0;
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Two address spaces supported: Memory or IO.
|
|
|
|
* PCI_Config is not supported here because the GAS struct is insufficient
|
|
|
|
*/
|
|
|
|
switch (reg->address_space_id) {
|
|
|
|
case ACPI_ADR_SPACE_SYSTEM_MEMORY:
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_os_read_memory((acpi_physical_address) address,
|
|
|
|
value, width);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
case ACPI_ADR_SPACE_SYSTEM_IO:
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_os_read_port((acpi_io_address) address,
|
|
|
|
value, width);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
default:
|
2006-01-27 16:43:00 -05:00
|
|
|
ACPI_ERROR((AE_INFO,
|
|
|
|
"Unsupported address space: %X",
|
|
|
|
reg->address_space_id));
|
2005-04-16 18:20:36 -04:00
|
|
|
return (AE_BAD_PARAMETER);
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_IO,
|
|
|
|
"Read: %8.8X width %2d from %8.8X%8.8X (%s)\n",
|
|
|
|
*value, width,
|
|
|
|
ACPI_FORMAT_UINT64(address),
|
|
|
|
acpi_ut_get_region_name(reg->address_space_id)));
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
return (status);
|
|
|
|
}
|
|
|
|
|
|
|
|
/******************************************************************************
|
|
|
|
*
|
|
|
|
* FUNCTION: acpi_hw_low_level_write
|
|
|
|
*
|
|
|
|
* PARAMETERS: Width - 8, 16, or 32
|
|
|
|
* Value - To be written
|
|
|
|
* Reg - GAS register structure
|
|
|
|
*
|
|
|
|
* RETURN: Status
|
|
|
|
*
|
|
|
|
* DESCRIPTION: Write to either memory or IO space.
|
|
|
|
*
|
|
|
|
******************************************************************************/
|
|
|
|
|
|
|
|
acpi_status
|
2005-08-05 00:44:28 -04:00
|
|
|
acpi_hw_low_level_write(u32 width, u32 value, struct acpi_generic_address * reg)
|
2005-04-16 18:20:36 -04:00
|
|
|
{
|
2005-08-05 00:44:28 -04:00
|
|
|
u64 address;
|
|
|
|
acpi_status status;
|
2005-04-16 18:20:36 -04:00
|
|
|
|
ACPI: ACPICA 20060421
Removed a device initialization optimization introduced in
20051216 where the _STA method was not run unless an _INI
was also present for the same device. This optimization
could cause problems because it could allow _INI methods
to be run within a not-present device subtree (If a
not-present device had no _INI, _STA would not be run,
the not-present status would not be discovered, and the
children of the device would be incorrectly traversed.)
Implemented a new _STA optimization where namespace
subtrees that do not contain _INI are identified and
ignored during device initialization. Selectively running
_STA can significantly improve boot time on large machines
(with assistance from Len Brown.)
Implemented support for the device initialization case
where the returned _STA flags indicate a device not-present
but functioning. In this case, _INI is not run, but the
device children are examined for presence, as per the
ACPI specification.
Implemented an additional change to the IndexField support
in order to conform to MS behavior. The value written to
the Index Register is not simply a byte offset, it is a
byte offset in units of the access width of the parent
Index Field. (Fiodor Suietov)
Defined and deployed a new OSL interface,
acpi_os_validate_address(). This interface is called during
the creation of all AML operation regions, and allows
the host OS to exert control over what addresses it will
allow the AML code to access. Operation Regions whose
addresses are disallowed will cause a runtime exception
when they are actually accessed (will not affect or abort
table loading.)
Defined and deployed a new OSL interface,
acpi_os_validate_interface(). This interface allows the host OS
to match the various "optional" interface/behavior strings
for the _OSI predefined control method as appropriate
(with assistance from Bjorn Helgaas.)
Restructured and corrected various problems in the
exception handling code paths within DsCallControlMethod
and DsTerminateControlMethod in dsmethod (with assistance
from Takayoshi Kochi.)
Modified the Linux source converter to ignore quoted string
literals while converting identifiers from mixed to lower
case. This will correct problems with the disassembler
and other areas where such strings must not be modified.
The ACPI_FUNCTION_* macros no longer require quotes around
the function name. This allows the Linux source converter
to convert the names, now that the converter ignores
quoted strings.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
2006-04-21 17:15:00 -04:00
|
|
|
ACPI_FUNCTION_NAME(hw_low_level_write);
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
/*
|
|
|
|
* Must have a valid pointer to a GAS structure, and
|
|
|
|
* a non-zero address within. However, don't return an error
|
|
|
|
* because the PM1A/B code must not fail if B isn't present.
|
|
|
|
*/
|
|
|
|
if (!reg) {
|
|
|
|
return (AE_OK);
|
|
|
|
}
|
|
|
|
|
2006-06-23 17:04:00 -04:00
|
|
|
/* Get a local copy of the address. Handles possible alignment issues */
|
2005-04-16 18:20:36 -04:00
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_MOVE_64_TO_64(&address, ®->address);
|
2005-04-16 18:20:36 -04:00
|
|
|
if (!address) {
|
|
|
|
return (AE_OK);
|
|
|
|
}
|
|
|
|
|
|
|
|
/*
|
|
|
|
* Two address spaces supported: Memory or IO.
|
|
|
|
* PCI_Config is not supported here because the GAS struct is insufficient
|
|
|
|
*/
|
|
|
|
switch (reg->address_space_id) {
|
|
|
|
case ACPI_ADR_SPACE_SYSTEM_MEMORY:
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_os_write_memory((acpi_physical_address) address,
|
|
|
|
value, width);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
case ACPI_ADR_SPACE_SYSTEM_IO:
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
status = acpi_os_write_port((acpi_io_address) address,
|
|
|
|
value, width);
|
2005-04-16 18:20:36 -04:00
|
|
|
break;
|
|
|
|
|
|
|
|
default:
|
2006-01-27 16:43:00 -05:00
|
|
|
ACPI_ERROR((AE_INFO,
|
|
|
|
"Unsupported address space: %X",
|
|
|
|
reg->address_space_id));
|
2005-04-16 18:20:36 -04:00
|
|
|
return (AE_BAD_PARAMETER);
|
|
|
|
}
|
|
|
|
|
2005-08-05 00:44:28 -04:00
|
|
|
ACPI_DEBUG_PRINT((ACPI_DB_IO,
|
|
|
|
"Wrote: %8.8X width %2d to %8.8X%8.8X (%s)\n",
|
|
|
|
value, width,
|
|
|
|
ACPI_FORMAT_UINT64(address),
|
|
|
|
acpi_ut_get_region_name(reg->address_space_id)));
|
2005-04-16 18:20:36 -04:00
|
|
|
|
|
|
|
return (status);
|
|
|
|
}
|