79 lines
2.4 KiB
C
79 lines
2.4 KiB
C
|
/*
|
||
|
|
* Definitions for Motorola SPS Sandpoint Test Platform
|
||
|
|
*
|
||
|
|
* Author: Mark A. Greer
|
||
|
|
* mgreer@mvista.com
|
||
|
|
*
|
||
|
|
* 2000-2003 (c) MontaVista, Software, Inc. This file is licensed under
|
||
|
|
* the terms of the GNU General Public License version 2. This program
|
||
|
|
* is licensed "as is" without any warranty of any kind, whether express
|
||
|
|
* or implied.
|
||
|
|
*/
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Sandpoint uses the CHRP map (Map B).
|
||
|
|
*/
|
||
|
|
|
||
|
|
#ifndef __PPC_PLATFORMS_SANDPOINT_H
|
||
|
|
#define __PPC_PLATFORMS_SANDPOINT_H
|
||
|
|
|
||
|
|
#include <asm/ppcboot.h>
|
||
|
|
|
||
|
|
#if 0
|
||
|
|
/* The Sandpoint X3 allows the IDE interrupt to be directly connected
|
||
|
|
* from the Windbond (PCI INTC or INTD) to the serial EPIC. Someday
|
||
|
|
* we should try this, but it was easier to use the existing 83c553
|
||
|
|
* initialization than change it to route the different interrupts :-).
|
||
|
|
* -- Dan
|
||
|
|
*/
|
||
|
|
#define SANDPOINT_IDE_INT0 23 /* EPIC 7 */
|
||
|
|
#define SANDPOINT_IDE_INT1 24 /* EPIC 8 */
|
||
|
|
#else
|
||
|
|
#define SANDPOINT_IDE_INT0 14 /* 8259 Test */
|
||
|
|
#define SANDPOINT_IDE_INT1 15 /* 8259 Test */
|
||
|
|
#endif
|
||
|
|
|
||
|
|
/*
|
||
|
|
* The sandpoint boards have processor modules that either have an 8240 or
|
||
|
|
* an MPC107 host bridge on them. These bridges have an IDSEL line that allows
|
||
|
|
* them to respond to PCI transactions as if they were a normal PCI devices.
|
||
|
|
* However, the processor on the processor side of the bridge can not reach
|
||
|
|
* out onto the PCI bus and then select the bridge or bad things will happen
|
||
|
|
* (documented in the 8240 and 107 manuals).
|
||
|
|
* Because of this, we always skip the bridge PCI device when accessing the
|
||
|
|
* PCI bus. The PCI slot that the bridge occupies is defined by the macro
|
||
|
|
* below.
|
||
|
|
*/
|
||
|
|
#define SANDPOINT_HOST_BRIDGE_IDSEL 12
|
||
|
|
|
||
|
|
/*
|
||
|
|
* Serial defines.
|
||
|
|
*/
|
||
|
|
#define SANDPOINT_SERIAL_0 0xfe0003f8
|
||
|
|
#define SANDPOINT_SERIAL_1 0xfe0002f8
|
||
|
|
|
||
|
|
#define RS_TABLE_SIZE 2
|
||
|
|
|
||
|
|
/* Rate for the 1.8432 Mhz clock for the onboard serial chip */
|
||
|
|
#define BASE_BAUD ( 1843200 / 16 )
|
||
|
|
#define UART_CLK 1843200
|
||
|
|
|
||
|
|
#ifdef CONFIG_SERIAL_DETECT_IRQ
|
||
|
|
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF|ASYNC_AUTO_IRQ)
|
||
|
|
#else
|
||
|
|
#define STD_COM_FLAGS (ASYNC_BOOT_AUTOCONF)
|
||
|
|
#endif
|
||
|
|
|
||
|
|
#define STD_SERIAL_PORT_DFNS \
|
||
|
|
{ 0, BASE_BAUD, SANDPOINT_SERIAL_0, 4, STD_COM_FLAGS, /* ttyS0 */ \
|
||
|
|
iomem_base: (u8 *)SANDPOINT_SERIAL_0, \
|
||
|
|
io_type: SERIAL_IO_MEM }, \
|
||
|
|
{ 0, BASE_BAUD, SANDPOINT_SERIAL_1, 3, STD_COM_FLAGS, /* ttyS1 */ \
|
||
|
|
iomem_base: (u8 *)SANDPOINT_SERIAL_1, \
|
||
|
|
io_type: SERIAL_IO_MEM },
|
||
|
|
|
||
|
|
#define SERIAL_PORT_DFNS \
|
||
|
|
STD_SERIAL_PORT_DFNS
|
||
|
|
|
||
|
|
#endif /* __PPC_PLATFORMS_SANDPOINT_H */
|