Fixes a build error in absence of CONFIG_IPV6:
drivers/net/netxen/netxen_nic_main.c:1189: error: implicit declaration of function 'ipv6_hdr'
drivers/net/netxen/netxen_nic_main.c:1189: error: invalid type argument of '->'
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For NX3031 only one I/O range is mapped, so unmapping other
two which are used by older chips, causes this warning on
ppc64.
"Attempt to iounmap early bolted mapping at 0x0000000000000000"
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
b44 chip has some hardware limitations, that need GFP_DMA bounce
buffers in some situations.
In order to not deplete DMA zone, we should keep allocated GFP_DMA skb
only for driver use. At rx time, we copy such skb to newly allocated
skb, reusing existing copybreak infrastructure.
On machines with low amount of memory, all skb meet the hardware limitation,
so no copy is needed. We detect this situation using a new device flag, set
to one if one GFP_DMA skb was ever allocated by b44_alloc_rx_skb().
Previously allocated skb, even outside from DMA zone will then be recycled,
to have minimal impact on DMA zone use.
Signed-off-by: Eric Dumazet <dada1@cosmosbay.com>
Tested-by: Ionut Leonte <ionut.leonte@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As the kernel warning states: "IRQF_DISABLED is not guaranteed on shared
IRQs". Since these IRQs' values are hardcoded and my test system doesn't
show any shared use of IRQs at all, rather make them non-shared than
non-disabled.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Apparently this doesn't make sense. Otherwise the queue gets disabled as
soon as it's getting empty and can only be resurrected by a driver
restart.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Originally this must have been a rewrite error when introducing
'chain_index'. But the original driver did not use the previous chain
item everywhere: when altering the address tx_chain_tail points to, it
should move forward, not backwards.
Also this is not an "index" but rather the penultimate element in the
chain, so rename it accordingly.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Triggering TX before the write to the DMA status mask register leads to
transferring packets with maximum payload no matter what the actual
packet size is.
While here, also trigger RX scheduling after writing the DMA status mask
register, like it was in the original driver before it was sent
upstream.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The called netif_rx_schedule() does all the work for us:
- it checks the return value of netif_rx_schedule_prep() and
- if everything is ok calls __netif_rx_schedule().
Before this change, the driver received absolutely nothing.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This function needs an early exit condition to function properly, or
else caller assumes napi workload wasn't enough to handle all received
packets and korina_rx is called again (and again and again and ...).
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this the driver will crash when the NIC is being restarted.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The new value is the one used in the external patch before and allows at
least a standard MTU of 1500 to be handled correctly. Impact of this
change gets visible when bigger packets are to be received, issuing:
| ping -s 492 <IP>
and bigger payload sized led to 100% packet loss.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Acked-by: Florian Fainelli <florian@openwrt.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Using platform_set_drvdata() here makes no sense, since the driver_data
field has already been filled with valuable data (i.e. the MAC address).
Also having driver_data point to the net_device is rather pointless
since struct korina_device contains an apropriate field for it.
Signed-off-by: Phil Sutter <n0-1@freewrt.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "read for interrupts" flag must be set before enabling slow-path
interrupts as well (and not just before fast-path interrupts)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Too big packets could pass due to wrong filter size
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong initialization of the multi-queue indirection table - it should
be using the function and not the port index
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The size of the doorbell is 4KB, this bug become visible when using
more than 8 queues
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding missing le_to_cpu and disabling wrong HW endianity flag (the
two complete each other)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Wrong handling of tagged packet if VLAN offload is disabled caused
packets to get corrupted
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Without this lock, in some race conditions the driver missed link
change indication
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the page size is not 4KB, the FW must be programmed to work with
the right SGE boundaries and fragment list length.
To avoid confusion with the BCM_PAGE_SIZE which is set to 4KB for the
FW sake, another alias for the system page size was added to
explicitly indicate that it is meant for the SGE
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While working on IA64, it became clear that the following memory
barriers are missing
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since slow-path events, including link update, are handled in
work-queue, a race condition was introduced in the self-test that
sometimes caused the link status to fail: the self-test was running
under RTNL lock, and if the link-watch was scheduled it stoped the
shared work-queue (waiting for the RTNL lock) and so the link update
event was not handled until the self-test ended (releasing the RTNL
lock) with failure (since the link status was not updated)
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch hooks up the start_xmit/tx_timeout/get_stats callbacks
in the ax88796 driver since they no longer are installed by the
lib8390 code. Without this patch the function dev_hard_start_xmit()
crashes due to a start_xmit callback with the value NULL.
While at it, update the ax88796 driver to make use of use of struct
net_device_ops.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds an init_dummy_netdev() function that gets a network device
structure (allocation and lifetime entirely under caller's control) and
initialize the minimum amount of fields so it can be used to schedule
NAPI polls without registering a full blown interface. This is to be
used by drivers that need to tie several hardware interfaces to a single
NAPI poll scheduler due to HW limitations.
It also updates the ibm_newemac driver to use that, this fixing the
oops on 2.6.29 due to passing NULL as "dev" to netif_napi_add()
Symbol is exported GPL only a I don't think we want binary drivers doing
that sort of acrobatics (if we want them at all).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Tested-by: Geert Uytterhoeven <Geert.Uytterhoeven@sonycom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Taken from http://bugzilla.kernel.org/show_bug.cgi?id=12397
We're doing an sprintf of an 11-char string into an 11-char buffer.
Whoops. It breaks firmware uploading.
Reported-by: Jos-Vicente Gilabert <josevteg@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Bail out if pci_map_single() fails while replenishing rx ring.
o Drop packet if pci_map_{single,page}() fail in tx.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some firmware commands like mac address addition/deletion are sent
on the transmit ring. So need to hold the tx lock before touching
tx producer/consumer indices.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fixes a tiny memory leak when driver is unloaded. The mac
address list maintained in netxen_adapter needs to deleted when
driver is going down.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Fix order or rom register writes.
o Reduce udelays when writing rom registers.
This cuts the firmware init time by 40%.
o Do not reset core/memory clocks when reinitializing driver.
Firmware willl handle this when initialized.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Read negotiated link speed when link state changes.
o Fix link speed reporting for hybrid nic boards, which have both 1Gbps and
10Gbps ports.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o fix the ip/tcp hdr offset in tx descriptors for ipv6.
o cleanup xmit function, move the tso checks into separate function,
this reduces unnecessary endian conversions back and forth.
o optimize macros to initialize tx descriptors.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Set restricted (little endian) data types in firmware command
requests and responses.
o Remove unnecessary conversion to LE when writing registers.
Signed-off-by: Dhananjay Phadke <dhananjay@netxen.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The attached patch modifies the sis900 driver when the MAC address
read from the hardware is invalid. As suggested, the patch now
generates a random address so that the user can go on and use
the hardware. In any case a message is also shown to warn on the
unexpected condition.
This seems to happen with newer HW implementation of the sis900
chipset, since this never came up before.
Patch is against vanilla 2.6.28 (but the driver doesn't change so often,
so it will probably apply to older/newer versions too).
See bugzilla ID 10201 and 11649 and ignore the previous patch.
Signed-off-by: Daniele Venzano <venza@brownhat.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If something goes wrong attaching to phy driver, we weren't freeing
the IRQ.
Signed-off-by: Mike Ditto <mditto@consentry.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Freescale on-chip TBI PHYs reports PHY ID as 0x0, but as of
commit 3ee82383f0
Author: Giulio Benetti <giulio.benetti@micronovasrl.com>
Date: Thu Nov 13 21:53:13 2008 +0000
phy: fix phy address bug
PHYID returns 0xffff and not 0xffffffff when not found and in some
case(at91sam9263) 0x0. Maybe this patch could be useful.
phy_device.c treats PHY ID == 0x0 as bogus IDs, and that results in
gianfar driver failure to see the TBI PHYs. This code snippet triggers:
if (!priv->tbiphy) {
printk(KERN_WARNING "SGMII mode requires that the device "
"tree specify a tbi-handle\n");
return;
}
Although tbi-handle is specified in the device tree.
Btw, technically PHY ID == 0x0 is a valid ID (if we ever see a PHY
manufactured by Xerox :-).
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by Russell King:
drivers/net/arm/etherh.c:649: error: unknown field 'ndo_set_mac_addr' specified in initializer
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/wireless/p54/p54common.c: In function ‘p54_config’:
drivers/net/wireless/p54/p54common.c:1853: warning: ‘ret’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/iwlwifi/iwl-3945.c: In function ‘iwl3945_txpower_set_from_eeprom’:
drivers/net/wireless/iwlwifi/iwl-3945.c:2222: warning: ‘power_idx’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/b43legacy/main.c: In function ‘b43legacy_op_dev_config’:
drivers/net/wireless/b43legacy/main.c:2468: warning: ‘up_dev’ may be used uninitialized in this function
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/wireless/b43/main.c: In function ‘b43_op_config’:
drivers/net/wireless/b43/main.c:3264: warning: ‘gmode’ may be used uninitialized
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commits:
7a95d267fb
("net: ppp_generic - use idr technique instead of cardmaps")
ab5024ab23
("net: ppp_generic - use DEFINE_IDR for static initialization")
introduced usage of IDR functionality but broke userspace side.
Before this commits it was possible to allocate new ppp interface with
specified number. Now it fails with EINVAL. Fix it by trying to
allocate interface with specified unit number and return EEXIST if
fail which allow pppd to ask us to allocate new unit number.
And fix messages on memory allocation fails - add details that it's
PPP module who is complaining.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Filip Aben says this fix is neccessary for big endian machines.
Signed-off-by: Denis Joseph Barrow <D.Barow@option.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The TX op should return NETDEV_TX_OK or NETDEV_TX_BUSY.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TXD_W0_CIPHER field is a 1-bit field. It only acts as boolean value
to indicate if the frame must be encrypted or not.
The way rt2x00_set_field32() worked it would grab the least signifcant bit
from txdesc->cipher and use that as value. Because of that WEP 64 and TKIP
worked since they had odd-numbered values, while WEP 128 and AES were
even numbers and didn't work.
Correctly booleanize the txdecs->cipher value to allow the hardware to
encrypt the outgoing data. After this we can enable HW crypto by default again.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
