This code became ineffective a few Linux releases ago and is not
required anyway.
Note from Christoph Hellwig: scsi_cmnd.request_buffer is always a
scatterlist these days. Checking random bites into it and then
mangling the data in sbp2_check_sbp2_response will cause really bad
memory corruption when you're not lucky enough to have the check not
trigger by luck.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Since broadcast transactions are already complete when the request has
been sent, the same transaction label can be reused all over again, see
IEEE 1394 7.3.2.5 and 6.2.4.3. Therefore we can reduce the footprint
of struct hpsb_host by the size of one struct hpsb_tlabel_pool.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Add support for the following types of hardware:
+ nodes that have a link speed < PHY speed
+ 1394b PHYs that are less than S800 capable
+ 1394b/1394a adapter cable between two 1394b PHYs
Also, S1600 and S3200 are now supported if IEEE1394_SPEED_MAX is raised.
A probing function is added to nodemgr's config ROM fetching routine
which adjusts the allowable speed if an access problem was encountered.
Pros and Cons of the approach:
+ minimum code footprint to support this less widely used hardware
+ nearly no overhead for unaffected hardware
- ineffective before nodemgr began to read the ROM of affected nodes
- ineffective if ieee1394 is loaded with disable_nodemgr=1
The speed map CSRs which are published to the bus are not touched by the
patch.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: Hakan Ardo <hakan@debian.org>
Cc: Calculex <linux@calculex.com>
Cc: Robert J. Kosinski <robk@cmcherald.com>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
This patch modifies the ohci1394.c file to enable and manage the "cycle too
long" interrupt.
If this interrupt occurs, the "LinkControl.CycleMaster" bit of the host
controller is reseted. This implies, that the host controller does not send
"cycle start" packet anymore freezing then the isochronous communication.
The management of the interrupt added by the patch is that when the interrupt
occurs, the OHCI irq handler prints a kernel log warning and then sets the
"LinkControl.CycleMaster" bit again resuming the isochronous communication.
Signed-off-by: Jean-Baptiste Mur <jeanbaptiste@maunakeatech.com>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Ben Collins <bcollins@debian.org>
Cc: Jody McIntyre <scjody@modernduck.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
The workarounds are not required for DViCO Momobay FX-3A and AFAIR not
for Momobay CX-2. These contain an TSB42AA9A but feature the same
firmware_revision value as the older DViCO Momobay CX-1.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
spotted by Adrian Bunk. Also remove some superfluous comments.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
when attempting to find the 'last' part of the dma region continue the
search from where we left off, instead of starting the search over.
Signed-off-by: Jim Westfall <jwestfall@surrealistic.net>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
When working with multiple cameras and intensive applications, our logs
get flooded with video1394 information which isn't of much interest.
Any objections to demoting these messages to debug messages?
Signed-off-by: Daniel Drake <dsd@gentoo.org>
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
On 64-bit machines, we just lost the uppermost 32 bits.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This fixes two independent problems: it would not save the PCI state on
suspend (and thus try to resume a nonexistent state on resume), and
while shut off, if an interrupt happened on the same shared irq, the irq
handler would react very badly to the interrupt status being an invalid
all-ones state.
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Received from Mark Salyzyn
clear_user return is 0 for success, the code fragment is written to
assume that it is the count of the number of bytes zero'd.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This is a hold over from the end device/expander conversion. Apparently
the rphy list pointer is never initialised, so list_del() on the
uninitialised pointer can panic the system
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
People have been reporting that PPP connections over ptys, such as
used with PPTP, will hang randomly when transferring large amounts of
data, for instance in http://bugzilla.kernel.org/show_bug.cgi?id=6530.
I have managed to reproduce the problem, and the patch below fixes the
actual cause.
The problem is not in fact in ppp_async.c but in n_tty.c. What
happens is that when pptp reads from the pty, we call read_chan() in
drivers/char/n_tty.c on the master side of the pty. That copies all
the characters out of its buffer to userspace and then calls
check_unthrottle(), which calls the pty unthrottle routine, which
calls tty_wakeup on the slave side, which calls ppp_asynctty_wakeup,
which calls tasklet_schedule. So far so good. Since we are in
process context, the tasklet runs immediately and calls
ppp_async_process(), which calls ppp_async_push, which calls the
tty->driver->write function to send some more output.
However, tty->driver->write() returns zero, because the master
tty->receive_room is still zero. We haven't returned from
check_unthrottle() yet, and read_chan() only updates tty->receive_room
_after_ calling check_unthrottle. That means that the driver->write
call in ppp_async_process() returns 0. That would be fine if we were
going to get a subsequent wakeup call, but we aren't (we just had it,
and the buffer is now empty).
The solution is for n_tty.c to update tty->receive_room _before_
calling the driver unthrottle routine. The patch below does this.
With this patch I was able to transfer a 900MB file over a PPTP
connection (taking about 25 minutes), whereas without the patch the
connection would always stall in under a minute.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
convert au1000_eth driver to use PHY framework and garbage collected
functions and identifiers that became unused/obsolete in the process
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bug fix: mv_eng_timeout() calls mv_err_intr() without first grabbing the host lock,
which can lead to all sorts of interesting scenarios.
This whole error-handling portion of sata_mv is nasty (and will get fixed for
the new EH stuff), but for now this patch will help keep it on life-support.
Signed-off-by: Mark Lord <liml@rtr.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
According to Intel ICH spec, there are several rules that Base Address
should be programmed before IOSE (PCICMD register ) enabled.
For example ICH7:
12.1.3 SATA : the base address register for the bus master register
should be programmed before this bit is set.
11.1.3: PCICMD (USB): The base address register for USB should be
programmed before this bit is set.
....
To make sure kernel code follow this rule , and prevent unnecessary
confusion. I proposal this patch.
Signed-off-by: Luming Yu <luming.yu@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
At least one laptop blew up on resume from suspend with a black screen due
to a lack of this patch. By only writing back config space that is
different, we minimise the possibility of accidents like this.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We currently don't handle errors properly when resuming a PCI device:
* In pci_default_resume() we capture the error code returned by
pci_enable_device() but don't pass it up to the caller.
Introduced by commit 95a629657d
* In pci_resume_device(), the errors possibly returned by the driver's
.resume method or by the generic pci_default_resume() function are
ignored.
This patch fixes both issues.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Priority: not critical; makes init code discardable.
Fix section mismatch warnings:
WARNING: drivers/net/3c501.o - Section mismatch: reference to .init.text:el1_probe from .text between 'init_module' (at offset 0x812) and 'cleanup_module'
WARNING: drivers/net/3c503.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x661) and 'cleanup_card'
WARNING: drivers/net/3c505.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x228d) and 'cleanup_module'
WARNING: drivers/net/3c507.o - Section mismatch: reference to .init.text:el16_probe from .text between 'init_module' (at offset 0xa99) and 'cleanup_module'
WARNING: drivers/net/3c523.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x12e7) and 'cleanup_module'
WARNING: drivers/net/3c527.o - Section mismatch: reference to .init.text:mc32_probe from .text between 'init_module' (at offset 0xd8d) and 'cleanup_module'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Priority: not critical; makes init code discardable.
Removes one duplicate assignment.
Fix section mismatch warnings:
WARNING: drivers/net/smc-ultra.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x369) and 'cleanup_card'
WARNING: drivers/net/smc-ultra32.o - Section mismatch: reference to .init.text:ultra32_probe from .text between 'init_module' (at offset 0x254) and 'cleanup_module'
WARNING: drivers/net/smc9194.o - Section mismatch: reference to .init.text:smc_init from .text between 'init_module' (at offset 0x997) and 'cleanup_module'
WARNING: drivers/net/smc9194.o - Section mismatch: reference to .init.data: from .data between 'smcdev.0' (at offset 0x44) and '__param_str_io'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Priority: not critical; makes init code discardable.
Fix section mismatch warnings:
WARNING: drivers/net/hp-plus.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x387) and 'cleanup_card'
WARNING: drivers/net/hp.o - Section mismatch: reference to .init.data: from .text between 'hp_init_card' (at offset 0x310) and 'init_module'
WARNING: drivers/net/hp.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x367) and 'cleanup_card'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Sat, 10 Jun 2006 14:11:42 +0200 (MEST) Mikael Pettersson wrote:
> While compiling 2.6.17-rc6 for a 486 with an NE2000 ISA ethernet card, I got:
>
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x158) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x176) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x183) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x1ea) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.data:isapnp_clone_list from .text between 'init_module' (at offset 0x251) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x266) and 'ne_block_input'
> WARNING: drivers/net/ne.o - Section mismatch: reference to .init.text: from .text between 'init_module' (at offset 0x29b) and 'ne_block_input'
>
> Not sure how serious this is; the driver seems to work fine later on.
Doesn't look serious. init_module() is not __init, but it calls
some __init functions and touches some __initdata.
BTW, I would be happy to see some consistent results from modpost
section checking. I don't see all of these warnings (I see only 1)
when using gcc 3.3.6. What gcc version are you using?
Does that matter? (not directed at anyone in particular)
Patch below fixes it for me. Please test/report.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If a PCI bus error/fault triggers a PCI bus reset, attempts to get the
ethernet packet count statistics from the hardware will fail, returning
garbage data upstream. This patch skips statistics data collection if the
PCI device is not on the bus.
This patch presumes that an earlier patch,
[PATCH] PCI Error Recovery: e1000 network device driver
has already been applied.
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In file included from drivers/net/smc911x.c:84:
drivers/net/smc911x.h:46:9: warning: "SMC_USE_16BIT" is not defined
drivers/net/smc911x.h:60:9: warning: "SMC_USE_32BIT" is not defined
drivers/net/smc911x.h:73:10: warning: "SMC_USE_PXA_DMA" is not defined
drivers/net/smc911x.c: In function `smc911x_reset':
drivers/net/smc911x.c:247: warning: implicit declaration of function `SMC_inl'
drivers/net/smc911x.c:249: warning: implicit declaration of function `SMC_outl'
Cc: Dustin McIntire <dustin@sensoria.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains new device ids for forcedeth ethernet.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch bumps up the version number for config support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds support for diagnostic tests through ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch moves a few functions (no logic change) so that the next
patch has these functions defined.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch exposes hardware statistic counters through ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for configurable rx and tx checksum offloads through
ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes configuration bugs when modifying wol settings.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes configuration bugs when modifying phy settings.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for configurable flow control through ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch allows for configurable ring size through ethtool support.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There are a series of patches for configuration support in forcedeth and
one patch for device ids.
This patch is a cleanup of the a previous TSO patch.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The RQ_SCSI_* flags are a vestiage of a long past history. The EH code
still sets them but we never make use of that information. The other
users is pluto.c which never had a chance to work but needs to be kept
compiling to keep Davem happy, so copy over the definition there.
We could probably get rid of RQ_ACTIVE/RQ_INACTIVE aswell with some
work, there's only two more or less bogus looking uses in ubd and scsi.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
With Achim patch the last user (gdth) is switched away from scsi_request
so we an kill it now. Also disables some code in i2o_scsi that was
broken since the sg driver stopped using scsi_requests.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bump driver version number to reflect addition of various
fibre channel patches.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The driver uses msleep_interruptible() in the code path responsible
for resetting the card's ports via the lsiutil command. If a
<ctrl-c> is received during the reset it can leave a port in such
a state that the only way to regain its use is to reboot the system.
Changing from msleep_interruptible() to msleep() corrects the problem.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
While doing board reset testing I was able to put the system in
an infinite request/response loop between the scsi layer and
mptscsih_qcmd() by aborting the reset. This patch installs
a "SETUP RESET" handler which calls fc_remote_port_delete()
for all registered rports. This blocks the target which
prevents the loop. Additionally, should the reset fail to
complete, the transport will now terminate i/o to the target.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The fibre channel firmware provides a timer which is similar in purpose
to the fibre channel transport's device loss timer. The effect of this
timer is to extend the total time that a target will be missing beyond
the value associated with the transport's timer. This patch changes
the firmware timer to a default of one second which significantly reduces
the lag between when a target goes missing and the notification of the
fibre channel transport.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Move fibre channel event and reset handling to mptfc. This will
result in fewer changes over time that need to be applied to
either mptbase.c or mptscsih.c.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Avoid JBUS errors on some Niagara systems.
[FUSION]: Fix mptspi.c build with CONFIG_PM not set.
[TG3]: Handle Sun onboard tg3 chips more correctly.
[SPARC64]: Dump local cpu registers in sun4v_log_error()
From: Milton Miller <miltonm@bga.com>
The add_preferred_console call in rtas_console.c was not causing the
console to be selected. It turns out that the add_preferred_console was
being called after the hvc_console driver was registered. It only works
when it is called before the console driver is registered.
Reorder hvc_console.o after the hvc_console drivers to allow the selection
during console_initcall processing.
Signed-off-by: Milton Miller <miltonm@bga.com>
Signed-off-by: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Markus Lidel <Markus.Lidel@shadowconnect.com>
- Fixed locking of struct i2o_exec_wait in Executive-OSM
- Removed LCT Notify in i2o_exec_probe() which caused freeing memory and
accessing freed memory during first enumeration of I2O devices
- Added missing locking in i2o_exec_lct_notify()
- removed put_device() of I2O controller in i2o_iop_remove() which caused
the controller structure get freed to early
- Fixed size of mempool in i2o_iop_alloc()
- Fixed access to freed memory in i2o_msg_get()
See http://bugzilla.kernel.org/show_bug.cgi?id=6561
Signed-off-by: Markus Lidel <Markus.Lidel@shadowconnect.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Andrew Morton <akpm@osdl.org>
Work around the oops reported in
http://bugzilla.kernel.org/show_bug.cgi?id=6478.
Thanks to Ralf Hildebrandt <ralf.hildebrandt@charite.de> for testing and
reporting.
Acked-by: Dave Jones <davej@codemonkey.org.uk>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is really just a belt and braces test. The standards require
disks to respond DT not capable on a non-LVD bus ... however, not all
disks follow the standards ...
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Read the transciever register and display in the host transport
properties. I'm still not entirely sure what this does for multiple
transciever adapters (like some 160 ones) however, I suspect it
displays the transciever state of the switchable bus segment.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove
duplicates of the macro.
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
HighPoint RocketRAID 3220/3320 series 8 channel PCI-X SATA RAID Host
Adapters.
Fixes from original submission:
Merge Andrew Morton's patches:
- Provide locking for global list
- Fix debug printks
- uninline function with multiple callsites
- coding style fixups
- remove unneeded casts of void*
- kfree(NULL) is legal
- Don't "succeed" if register_chrdev() failed - otherwise we'll later
unregister a not-registered chrdev.
- Don't return from hptiop_do_ioctl() with the spinlock held.
- uninline __hpt_do_ioctl()
Update for Arjan van de Ven's comments:
- put all asm/ includes after the linux/ ones
- replace mdelay with msleep
- add pci posting flush
- do not set pci command reqister in map_pci_bar
- do not try merging sg elements in hptiop_buildsgl()
- remove unused outstandingcommands member from hba structure
- remove unimplemented hptiop_abort() handler
- remove typedef u32 hpt_id_t
Other updates:
- fix endianess
Signed-off-by: HighPoint Linux Team <linux@highpoint-tech.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Initial pass at converting the gdth driver away from the scsi_request
interface so that the request interface can be removed post 2.6.18
without breaking gdth. Based on changes from Christoph Hellwig
<hch@lst.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Get rid of all the SUN_570X logic and instead:
1) Make sure MEMARB_ENABLE is set when we probe the SRAM
for config information. If that is off we will get
timeouts.
2) Always try to sync with the firmware, if there is no
firmware running do not treat it as an error and instead
just report it the first time we notice this condition.
3) If there is no valid SRAM signature, assume the device
is onboard by setting TG3_FLAG_EEPROM_WRITE_PROT.
Update driver version and release date.
With help from Michael Chan and Fabio Massimo Di Nitto.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fallout from the incoming 64-bit-resource stuff:
drivers/mtd/maps/physmap.c: In function 'physmap_flash_probe':
drivers/mtd/maps/physmap.c:94: warning: format '%.8lx' expects type 'long
unsigned int', but argument 2 has type 'resource_size_t'
drivers/mtd/maps/physmap.c:94: warning: format '%.8lx' expects type 'long
unsigned int', but argument 3 has type 'resource_size_t'
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
drivers/char/agp/alpha-agp.c:138: warning: initialization from incompatible pointer type
drivers/char/agp/alpha-agp.c:139: warning: initialization from incompatible pointer type
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
drivers/char/agp/uninorth-agp.c: In function `agp_uninorth_suspend':
drivers/char/agp/uninorth-agp.c:332: warning: cast to pointer from integer of different size
drivers/char/agp/uninorth-agp.c: In function `agp_uninorth_resume':
drivers/char/agp/uninorth-agp.c:354: warning: cast from pointer to integer of different size
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
From: Malcom Parsons <malcolm.parsons@gmail.com>
When scrolling up in SCROLL_PAN_REDRAW mode with a large limited scroll
region, the bottom few lines have to be redrawn. Without this patch, the
wrong text is drawn into these lines, corrupting the display.
Observed in 2.6.14 when running an IRC client in the Nintendo DS linux
port.
I haven't tested if scrolling down has the same problem.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Richard Purdie
Add a power budget variable to the PXA OHCI platform data and add a
default value for the spitz platform(s) which prevents known failures
with certain USB devices.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Sometimes boards don't reset properly, and the address read out of the
EEPROM is zero. Stop the insanity before the device gets registered.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The transmit side code has a number of ring problems that caused some
of the Bugzilla reports. Rather than trying to fix the details, it is safer
to rewrite the code that handles transmit completion and freeing.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Consolidate all usage of ring low water mark to one value.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Since accessing the PHY can take 100's of usecs, use a work queue to
allow spinning in outside of soft/hard irq.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The following patch updates the myri10ge to 1.0.0, with the following changes:
* Switch to dma_alloc_coherent API.
* Avoid PCI burst when writing the firmware on chipset with unaligned completions.
* Use ethtool_op_set_tx_hw_csum instead of ethtool_op_set_tx_csum.
* Include linux/dma-mapping.h to bring DMA_32/64BIT_MASK on all architectures
(was missing at least on alpha).
* Some typo and warning fixes.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Andrew J. Gallatin <gallatin@myri.com>
drivers/net/myri10ge/myri10ge.c | 57 +++++++++++++++++++-----------
1 file changed, 37 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Various PCI bus errors can be signaled by newer PCI controllers.
This patch adds the PCI error recovery callbacks to the intel gigabit
ethernet e1000 device driver. The patch has been tested, and appears
to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Various PCI bus errors can be signaled by newer PCI controllers. This
patch adds the PCI error recovery callbacks to the intel ethernet e100
device driver. The patch has been tested, and appears to work well.
Signed-off-by: Linas Vepstas <linas@linas.org>
Acked-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
It was brought to our attention that the prefetches break e1000 traffic
on xscale/arm architectures. Remove them for now. We'll let them
stay in mm for a while, or find a better solution to enable.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
New code added in 2.6.17 caused setup_irq to print a warning when
running ethtool -t eth0 offline.
This test marks the request_irq call made by this test as a "probe"
to see if the interrupt is shared or not.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Various scsi drivers use scsi_cmnd.buffer and scsi_cmnd.bufflen in their
queuecommand functions. Those fields are internal storage for the
midlayer only and are used to restore the original payload after
request_buffer and request_bufflen have been overwritten for EH. Using
the buffer and bufflen fields means they do very broken things in error
handling.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch( originally submitted by Christoph Hellwig) removes
instance_lock and changes fw_outstanding variable data type to
atomic_t.
Signed-off-by: Sumant Patro <Sumant.Patro@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[BRIDGE]: fix locking and memory leak in br_add_bridge
[IRDA]: Missing allocation result check in irlap_change_speed().
[PPPOE]: Missing result check in __pppoe_xmit().
[NET]: Eliminate unused /proc/sys/net/ethernet
[NETCONSOLE]: Clean up initcall warning.
[TCP]: Avoid skb_pull if possible when trimming head
We can race and misset the suspend bit if iscsi_write_space is
called then iscsi_send returns with a failure indicating
there is no space.
To handle this this patch returns a error upwards allowing xmitworker
to decide if we need to try and transmit again. For the no
write space case xmitworker will not retry, and instead
let iscsi_write_space queue it back up if needed (this relies
on the work queue code to properly requeue us if needed).
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from davidw@netapp.com:
remove task type should return a task on success.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
from davidw@netapp.com:
We must grab the session lock when modifying the running lists.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If recovery failed or we are in recovery only overwrite the state
if we are going to terminate the session or if we logged back in.
STOP_CONN_SUSPEND and conn_cnt are not used. We only support
a single connection session ATM, so cleanup that code while
we are working around it.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
skb_clone() may fail, we should check the result.
Coverity CID: 1215.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Matt Mackall <mpm@selenic.com>
netconsole is being wrong here. If it wasn't enabled there's no error.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
zd1201 is wifi adapter, yet it is hiding in drivers/usb/net where
noone can find it. This moves Kconfig/Makefile zd1201 to the right
place.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The debug logging in bcm43xx_ieee80211_set_security() is pretty noisy.
Make it more silent.
Signed-off-by: Jason Lunz <lunz@falooley.org>
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cleanup coding style and other small stuff in zd1201. No real code
changes.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* master.kernel.org:/pub/scm/linux/kernel/git/brodo/pcmcia-fixes-2.6:
[PATCH] pcmcia: fix zeroing of cm4000_cs.c data
[PATCH] pcmcia: missing pcmcia_get_socket() result check
From: Andrew Morton <akpm@osdl.org>
drivers/rtc/rtc-m48t86.c: In function `m48t86_rtc_read_time':
drivers/rtc/rtc-m48t86.c:51: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:55: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:56: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:57: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:58: error: structure has no member named `ia64_mv'
drivers/rtc/rtc-m48t86.c:60: error: structure has no member named `ia64_mv'
readb() and writeb() are macros on ia64.
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Stefan Richter <stefanr@s5r6.in-berlin.de>
I added a failure check in patch "sbp2: variable status FIFO address (fix
login timeout)" --- alas for a wrong error value. This is a bug since
Linux 2.6.16. Leads to NULL pointer dereference if the call failed, and
bogus failure handling if call succeeded.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Cc: <stable@kernel.org>
Cc: Ben Collins <bcollins@debian.org>
Cc: Jody McIntyre <scjody@modernduck.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
The path grouping can fail due to non-unique pathgroup-IDs. The source for
the CPU-ID part of the ID was incorrectly specified on 64 bit systems.
Additionally, the length of the ID was too large due to incorrect data packing
declaration. Fix CPU-ID lowcore address and add missing packing declaration.
Signed-off-by: Peter Oberparleiter <peter.oberparleiter@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Florin Malita <fmalita@gmail.com>
The skb may be gone after netif_rx(), we can't use 'skb->len' to update the
stats. 'pkt_len' should work instead.
Coverity CID: 911.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Also add the Poll RX DMA Memory workaround to the DMA4
(xmitstatus) path.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When ipoib_stop() is called it first calls netif_stop_queue() to stop
the kernel from passing more packets to the network driver. However,
the completion handler may call netif_wake_queue() re-enabling packet
transfer.
This might result in leaks (we see AH leaks which we think can be
attributed to this bug) as new packets get posted while the interface
is going down.
Signed-off-by: Eli Cohen <eli@mellanox.co.il>
Signed-off-by: Michael Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Remove KERN_* suffixes from some cpufreq driver's dprintk-s.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The driver is selectable on other than Au1200 Alchemy systems but won't
build nor work - there is no MMC hw.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/pub/scm/linux/kernel/git/jejb/scsi-rc-fixes-2.6:
[SCSI] scsi_lib.c: properly count the number of pages in scsi_req_map_sg()
[SCSI] scsi_transport_sas: make write attrs writeable
[SCSI] scsi_transport_sas; fix user_scan
[SCSI] ppa: fix for machines with highmem
[SCSI] mptspi: reset handler shouldn't be called for other bus protocols
[SCSI] Blacklist entry for HP dat changer
Fix the incorrect calculation of how much to zero out in struct cm4000_dev
on device initialization.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The result of pcmcia_get_socket() may be NULL but ds_event() uses it
without checking.
Coverity CID: 436.
Signed-off-by: Florin Malita <fmalita@gmail.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
The calculation of nr_pages in scsi_req_map_sg() doesn't account for
the fact that the first page could have an offset that pushes the end
of the buffer onto a new page.
Signed-off-by: Bryan Holty <lgeek@frontiernet.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
From: NeilBrown <neilb@suse.de>
If an error is reported by a drive in a RAID array (which is done via
bi_end_io - in interrupt context), we call md_error and md_new_event which
calls sysfs_notify. However sysfs_notify grabs a mutex and so cannot be
called in interrupt context.
This patch just creates a variant of md_new_event which avoids the sysfs
call, and uses that. A better fix for later is to arrange for the event to
be called from user-context.
Note: avoiding the sysfs call isn't a problem as an error will not, by
itself, modify the sync_action attribute. (We do still need to
wake_up(&md_event_waiters) as an error by itself will modify /proc/mdstat).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Jeremy Higdon <jeremy@sgi.com>
This patch fixes a bug in sgiioc4 where it was using the default IDE port
I/O operations instead of MMIO.
The IDE part of the IOC4 chip uses MMIO to map the chip registers.
Unfortunately, the sgiioc4 driver uses the default port IO operations,
which happens to have worked for the past few years. That's about to
change, however, thus this change from inX/outX to readX/writeX.
Signed-off-by: Jeremy Higdon <jeremy@sgi.com>
Cc: Bartlomiej Zolnierkiewicz <B.Zolnierkiewicz@elka.pw.edu.pl>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Martin Michlmayr <tbm@cyrius.com>
Fix the following compilation error:
CC drivers/video/maxinefb.o
drivers/video/maxinefb.c:58: warning: initializer-string for array of chars is too long
drivers/video/maxinefb.c:58: warning: (near initialization for \u2018maxinefb_fix.id\u2019)
drivers/video/maxinefb.c:110: error: unknown field \u2018fb_get_fix\u2019 specified in initializer
drivers/video/maxinefb.c:110: error: \u2018gen_get_fix\u2019 undeclared here (not in a function)
drivers/video/maxinefb.c:111: error: unknown field \u2018fb_get_var\u2019 specified in initializer
drivers/video/maxinefb.c:111: error: \u2018gen_get_var\u2019 undeclared here (not in a function)
make[2]: *** [drivers/video/maxinefb.o] Error 1
Signed-off-by: Martin Michlmayr <tbm@cyrius.com>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Rodolfo Giometti <giometti@linux.it>
Fix the following warning on compilation:
drivers/video/au1100fb.c: In function `au1100fb_fb_setcolreg':
drivers/video/au1100fb.c:219: warning: ISO C90 forbids mixed declarations and code
drivers/video/au1100fb.c: In function `au1100fb_fb_pan_display':
drivers/video/au1100fb.c:321: warning: ISO C90 forbids mixed declarations and code
drivers/video/au1100fb.c: In function `au1100fb_fb_mmap':
drivers/video/au1100fb.c:387: warning: ISO C90 forbids mixed declarations and code
drivers/video/au1100fb.c: In function `au1100fb_drv_probe':
drivers/video/au1100fb.c:471: warning: unsigned int format, long unsigned int arg (arg 2)
drivers/video/au1100fb.c: At top level:
drivers/video/au1100fb.c:617: warning: initialization from incompatible pointer type
drivers/video/au1100fb.c:618: warning: initialization from incompatible pointer type
Signed-off-by: Rodolfo Giometti <giometti@linux.it>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Andrew Morton <akpm@osdl.org>
Revert commit ff4da2e262.
It broke APM suspend, probably because APM doesn't switch back to a VT
when suspending.
Tracked down by Matt Mackall <mpm@selenic.com>
Rafael sayeth:
"It only fixed the theoretical issue that a quick-handed user could
switch to X after processes have been frozen and before the devices
are suspended.
With the current userland suspend tools it shouldn't be necessary."
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Corey Minyard <minyard@acm.org>
This patch is pretty important to get in for IPMI, new systems have been
changing the way ACPI and IPMI interact, and this works around the problems
for now. This is a temporary fix until we get proper ACPI handling in
IPMI.
Fixed releasing already-allocated regions when a later request fails, and
forward-ported it to HEAD.
Some BIOSes reserve disjoint I/O regions in their ACPI tables for the IPMI
controller. This causes problems when trying to register the entire I/O
region. Therefore we must register each I/O port separately.
Signed-off-by: Jordan Hargrave <Jordan_Hargrave@dell.com>
Signed-off-by: Matt Domsch <Matt_Domsch@dell.com>
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Seiji Munetoh <seiji.munetoh@gmail.com>
Change the binary output format to actual ACPI TCPA log structure since the
current format does not contain all event-data information that need to
verify the PCRs in TPM. tpm_binary_bios_measurements_show() uses
get_event_name() to convert the binary event-data to ascii format, and puts
them as binary. However, to verify the PCRs, the event-data must be a
actual binary event-data used by SHA1 calc. in BIOS.
So, I think actual ACPI TCPA log is good for this binary output format.
That way, any userland tools easily parse this data with reference to TCG
PC specification.
Signed-off-by: Seiji Munetoh <seiji.munetoh@gmail.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: Seiji Munetoh <seiji.munetoh@gmail.com>
Fix "tcpa_pc_event" misalignment between enum, strings and TCG PC spec and
output of the event which contains a hash data.
Signed-off-by: Seiji Munetoh <seiji.munetoh@gmail.com>
Acked-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: David Hollister <david.hollister@amd.com>
After the system boots with the logo, if the first action is a scrollback, the
screen may become garbled. This patch ensures that the softback_curr value is
updated along with softback_in following the scrollback.
Signed-off-by: David Hollister <david.hollister@amd.com>
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: "Antonino A. Daplas" <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
MPT fusion driver initialization fails while second kernel is booting,
after a system crash (if kdump kernel is configured). Oops message is
pasted below.
*****************************************************************************
Fusion MPT base driver 3.03.08
Copyright (c) 1999-2005 LSI Logic Corporation
Fusion MPT SAS Host driver 3.03.08 ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 5 (level, low) -> IRQ 5
mptbase: Initiating ioc0 bringup
BUG: unable to handle kernel paging request at virtual address 00002608
printing eip:
c11782fd
*pde = 00000000
Oops: 0000 [#1]
Modules linked in:
CPU: 0
EIP: 0060:[<c11782fd>] Not tainted VLI
EFLAGS: 00010046 (2.6.17-rc1-16M #2)
EIP is at mptscsih_io_done+0x27/0x3a3
eax: c4fed000 ebx: c4fed000 ecx: 00002600 edx: 00000298
esi: c11782d6 edi: 00002600 ebp: 00000000 esp: c1332f74
ds: 007b es: 007b ss: 0068
Process swapper (pid: 0, threadinfo=c1332000 task=c128f9c0) Stack: <0>0000006c 00000020 00000298 00002600 c4fed000 c4fed000 c11782d6 0000260 0
00000000 c1172c49 c4fed000 c1305b40 00000005 00000000 c1172d75 c48877e0
c1029687 00000000 c1307fb8 00000000 c1305a00 00000001 00000000 c1307fb8
Call Trace:
<c11782d6> mptscsih_io_done+0x0/0x3a3 <c1172c49> mpt_turbo_reply+0xbb/0xd3
<c1172d75> mpt_interrupt+0x22/0x2b <c1029687> misrouted_irq+0x63/0xcb
<c10297b3> note_interrupt+0x43/0x98 <c10292f9> __do_IRQ+0x68/0x8f
<c1003fac> do_IRQ+0x36/0x4e
=======================
<c1002aa6> common_interrupt+0x1a/0x20 <c1001150> mwait_idle+0x1a/0x2a
<c10010bf> cpu_idle+0x40/0x5c <c1308610> start_kernel+0x17a/0x17c Code: 5e 5f 5d c3 55 89 cd 57 56 53 83 ec 14 89 54 24 0c 89 44 24 10 8b 90 cc 00 00 00 8b 4c 24 0c 81 c2 98 02 00 00 85 ed 89 54 24 08 <0f> b7 79 08 89 fe 74 04 0f b7 75 08 66 39 f7 75 0d 8b 44 24 0c
*******************************************************************************
o Kdump capture kernel boot fails during initialization of MPT fusion driver.
(LSI Logic / Symbios Logic SAS1064E PCI-Express Fusion-MPT SAS (rev 01))
o Problem is easily reproducible, if system crashed while some disk activity
like cp operation was going on.
o After a system crash, devices are not shutdown and capture kernel starts
booting while skipping BIOS. Hence underlying device is left in operational
state. In this case scsi contoller was left with interrupt line asserted
reply FIFO was not empty. When driver starts initializing in the second
kernel, it receives the interrupt the moment request_irq() is called.
Interrupt handler, reads the message from reply FIFO and tries to access
the associated message frame and panics, as in the new kernel's context
that message frame is not valid at all.
o In this scenario, probably we should delay the request_irq() call. First
bring up the IOC, reset it if needed and then should register for irq.
o I have tested the patch with SAS1064E and 53c1030 controllers.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Acked-by: "Moore, Eric Dean" <Eric.Moore@lsil.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] VIA PT880 Ultra support.
[AGPGART] Fix Nforce3 suspend on amd64.
[AGPGART] Enable SIS AGP driver on x86-64 for EM64T systems
mtdchar.c direcly copied part of struct mtd_info to userspace, thereby
implicitly making it part of the ABI. With this patch, struct
mtd_info is independent of the ABI and can have its fields removed,
reordered, etc.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
Ram devices get the extra capability of MTD_NO_ERASE - not requiring
an explicit erase before writing to it. Currently only mtdblock uses
this capability. Rest of the patch is a simple text replacement.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
No mtd user should ever check for the device type. Instead, device features
should be checked by the flags - if at all.
As a first step towards type removal, change MTD_ROM into MTD_GENERIC_TYPE.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
drivers/mtd/nand/nand_base.c: In function 'nand_transfer_oob':
drivers/mtd/nand/nand_base.c:909: warning: comparison of distinct pointer types lacks a cast
drivers/mtd/nand/nand_base.c: In function 'nand_do_read_oob':
drivers/mtd/nand/nand_base.c:1097: error: 'len' undeclared (first use in this function)
drivers/mtd/nand/nand_base.c:1097: error: (Each undeclared identifier is reported only once
drivers/mtd/nand/nand_base.c:1097: error: for each function it appears in.)
drivers/mtd/nand/nand_base.c: In function 'nand_fill_oob':
drivers/mtd/nand/nand_base.c:1411: warning: comparison of distinct pointer types lacks a cast
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Added different lifebook-versions and the CF-18 to the corresponding
dmi-table.
Signed-off-by: Kenan Esau <kenan.esau@conan.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Remove the numbered SW_* entries from the input system and assign names
to the existing users.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Correct touchpad left & right keys assignments for ALPS_OLDPROTO
that were swapped. Old protocol is used on UMAX ActionBook-530T
notebook.
Signed-off-by: Yotam Medini <yotam.medini@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
In sw_connect we leak 'buf' and 'idbuf' when we do not leave via one of
the fail* labels. This was spotted by the coverity checker.
Patch is compile tested only due to lack of hardware.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The raw read/write access to NAND (without ECC) has been changed in the
NAND rework. Expose the new way - setting the file mode via ioctl - to
userspace. Also allow to read out the ecc statistics information so userspace
tools can see that bitflips happened and whether errors where correctable
or not. Also expose the number of bad blocks for the partition, so nandwrite
can check if the data fits into the parition before writing to it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Return -EUCLEAN on read when a bitflip was detected and corrected, so the
clients can react and eventually copy the affected block to a spare one.
Make all in kernel users aware of the change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hopefully the last iteration on this!
The handling of out of band data on NAND was accompanied by tons of fruitless
discussions and halfarsed patches to make it work for a particular
problem. Sufficiently annoyed by I all those "I know it better" mails and the
resonable amount of discarded "it solves my problem" patches, I finally decided
to go for the big rework. After removing the _ecc variants of mtd read/write
functions the solution to satisfy the various requirements was to refactor the
read/write _oob functions in mtd.
The major change is that read/write_oob now takes a pointer to an operation
descriptor structure "struct mtd_oob_ops".instead of having a function with at
least seven arguments.
read/write_oob which should probably renamed to a more descriptive name, can do
the following tasks:
- read/write out of band data
- read/write data content and out of band data
- read/write raw data content and out of band data (ecc disabled)
struct mtd_oob_ops has a mode field, which determines the oob handling mode.
Aside of the MTD_OOB_RAW mode, which is intended to be especially for
diagnostic purposes and some internal functions e.g. bad block table creation,
the other two modes are for mtd clients:
MTD_OOB_PLACE puts/gets the given oob data exactly to/from the place which is
described by the ooboffs and ooblen fields of the mtd_oob_ops strcuture. It's
up to the caller to make sure that the byte positions are not used by the ECC
placement algorithms.
MTD_OOB_AUTO puts/gets the given oob data automaticaly to/from the places in
the out of band area which are described by the oobfree tuples in the ecclayout
data structre which is associated to the devicee.
The decision whether data plus oob or oob only handling is done depends on the
setting of the datbuf member of the data structure. When datbuf == NULL then
the internal read/write_oob functions are selected, otherwise the read/write
data routines are invoked.
Tested on a few platforms with all variants. Please be aware of possible
regressions for your particular device / application scenario
Disclaimer: Any whining will be ignored from those who just contributed "hot
air blurb" and never sat down to tackle the underlying problem of the mess in
the NAND driver grown over time and the big chunk of work to fix up the
existing users. The problem was not the holiness of the existing MTD
interfaces. The problems was the lack of time to go for the big overhaul. It's
easy to add more mess to the existing one, but it takes alot of effort to go
for a real solution.
Improvements and bugfixes are welcome!
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Most of those macros are unused and the used ones just obfuscate
the code. Remove them and fixup all users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand_oobinfo structure is not fitting the newer error correction
demands anymore. Replace it by struct nand_ecclayout and fixup the users
all over the place. Keep the nand_oobinfo based ioctl for user space
compability reasons.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The info structure for out of band data was copied into
the mtd structure. Make it a pointer and remove the ability
to set it from userspace. The position of ecc bytes is
defined by the hardware and should not be changed by software.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The platform structure was lacking an oobinfo field.
The NDFC driver had some remains from another tree.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
intelfb driver -- use the regular modedb table instead of the VESA modedb
table. Ideally, the 9xx stride patch should be applied first, since there
are modes in the VESA table that won't work without that patch.
Signed-off-by: Dennis Munsie <dmunsie@cecropia.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Use firmware EDID for the driver's private mode database.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Cc: Sylvain Meyer <sylvain.meyer@worldonline.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Fix integer option parsing in the intelfb driver. The macro wasn't
accounting for the equal sign past the option name. As a result,
the vram option always returned 0.
Signed-off-by: Eric Hustvedt <ehustvedt@cecropia.com>
Signed-off-by: Dennis Munsie <dmunsie@cecropia.com
Signed-off-by: Dave Airlie <airlied@linux.ie>
Okay, just to sum things up.
This forces libata to wait for up to 2 seconds for BUSY|DRQ to clear
on resume before continuing.
[jgarzik adds...] During testing we never saw DRQ asserted, but
nonetheless (a) this works and (b) testing for DRQ won't hurt.
Signed-off-by: Mark Lord <liml@rtr.ca>
Acked-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
max_id now means the maximum number of ids on the bus, which means it
is one greater than the largest possible id number.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The scsi_scan_host_selected() should return -EINVAL when the id is equal
to the max_id. Currently it uses ">" when comparing with max_id, and
hence leaves the border case when "id==max_id".
The channel and lun have values valid from 0 up to,
and including, max_channel or max_lun. But, the valid values for id
range from 0 to max_id-1. This patch fixes the problem.
Signed-off-by: Amit Arora <aarora@in.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Bump up version number, skip "4.6.0" because this might
clash with zfcp version in certain distros.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If zfcp's port erp fails we now call fc_remote_port_delete. This helps
to avoid offlined scsi devices if scsi commands time out due to path
failures. When an adapter erp fails we call fc_remote_port_delete for
all ports on that adapter.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace hex dump of bit error threshold data by log message showing
bit error threshold data human readable.
Signed-off-by: Ralph Wuerthner <rwuerthn@de.ibm.com>
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Removed some macros, struct members and typedefs which were
unused or not necessary.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Replace kmalloc/memset by kzalloc or kcalloc.
Signed-off-by: Andreas Herrmann <aherrman@de.ibm.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
[PATCH] powerpc: fix RTC/NVRAM accesses on Maple
[PATCH] ppc32 CPM_UART: various fixes for pq2 uart users
[PATCH] powerpc: linuxppc64.org no more
modedb table. Ideally, the 9xx stride patch should be applied first, since
there are modes in the VESA table that won't work without that patch.
Signed-off-by: Dennis Munsie <dmunsie@cecropia.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
and corrects calculation of stolen memory overhead.
Signed-off-by: Eric Hustvedt <ehustvedt@cecropia.com>
Signed-off-by: Dennis Munsie <dmunsie@cecropia.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
It replaced old rio_pcicopy(). That puppy did _not_ do readb() (unlike
rio_memcpy_toio()) and current implementation is simply broken - readb(NULL)
is never a valid thing to do.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
... there we are building a command in normal memory; it will be
copied to iomem (by ->Copy()) later. Use memcpy()...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
This is the second lcs driver patch containing the rest of lcs fixes.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Several problems occured with lcs device driver:
- device not operational anymore after cable pull/plug-in.
- unpredictable results occured, e.g. kernel panic
using cards of type QD8F.
- STOPLAN and delete multicast address command
were not proper recognized by OSA card under heavy network workload.
- channel/device error checks missing in interrupt handler.
To fix all problems at once recovery of lcs devices has been improved.
missing error checks in lcs interrupt handler has been added.
Once a hardware problem occurs lcs will recover the device now properly.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Frank Blaschka <Frank.Blaschka@de.ibm.com>
From: Frank Pavlic <fpavlic@de.ibm.com>
- fix fake_ll during initial device bringup. fake_ll was
not active after first start of the device.
Problem only occured when qeth was built without IPV6 support.
- avoid skb usage after invocation of qeth_flush_buffers,
because skb might already be freed.
- remove yet another useless netif_wake_queue in
qeth_softsetup_ipv6 since this function is only called
when device is going online. In this case card->state will
never be in state UP. So let the net_device queue down .
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Frank Pavlic <fpavlic@de.ibm.com>
- correct checking of sscanf-%n value in qeth_string_to_ipaddr().
- don't use netif_stop_queue outside the hard_start_xmit routine.
Rather use netif_tx_disable.
- don't call qeth_netdev_init on a recovery.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In case of a parse error for the cu3088 group attribute,
return -EINVAL instead of count.
Signed-off-by: Frank Pavlic <fpavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Hi,
This patch add new PCI ID for r8169 driver.
RTL8110SBL has this PCI ID.
Please aply.
Yoichi
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds flow control support for tx and rx pause frames in
forcedeth.
Signed-Off-By: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The original patch was using whitespaces instead of tabs.
Signed-off-by: Jens Osterkamp <Jens.Osterkamp@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During a code scan for another change I discovered that this call to
pcnet32_free_ring must be removed. If the open fails due to a lack of
memory all the ring structures are removed via the call to free_ring
and a subsequent call to open will dereference a null pointer in
pcnet32_init_ring.
Please apply to 2.6.17.
Signed-off-by: Don Fry <brazilnut@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Someone was waaay too aggressive and removed e1000's reboot notifier
instead of porting it to the new way of the shutdown handler. This change
broke wake on lan. Add the shutdown handler back in using the same method
as e100 uses.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
(cherry picked from c653e6351e commit)
We have a type pointer. Make use of it instead of the error prone nand_ids[i]
reference.
The NAND driver used to set default name settings from the chip ID
string for the device. The feature got lost during the rework. Add it back.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
nCE setting can be done when the first command is issued to the device.
We keep the deselect functionality as it makes sense to deassert nCE
when the device becomes idle.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Fix section mismatch warnings:
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:arlan_probe from .text between 'init_module' (at offset
0x3526) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.init.text:init_arlan_proc from .text between 'init_module' (at offset
0x3539) and 'cleanup_module'
WARNING: drivers/net/wireless/arlan.o - Section mismatch: reference to
.exit.text:cleanup_arlan_proc from .text between 'cleanup_module' (at
offset 0x356c) and 'arlan_diagnostic_info_string'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix section mismatch warning:
WARNING: drivers/net/wireless/wavelan.o - Section mismatch: reference to
.init.text: from .text between 'init_module' (at offset 0x371e) and
'cleanup_module'
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The TPM chip on the ThinkPad T60 and Z60 machines is returning 0xFFFF for
the vendor ID which is a check the driver made to double check it was
actually talking to the memory mapped space of a TPM. This patch removes
the check since it isn't absolutely necessary and was causing device
discovery to fail on these machines.
Signed-off-by: Kylene Hall <kjhall@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix compile bug with the S3C24XX SPI driver when CONFIG_PM is set.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This improves accuracy of the touchscreen and hwmon sensor readings,
addressing an issue noted by Imre Deak: there's an extra bit written before
the sample (12 bits) gets written out.
It also catches up to various comments, and makes the /proc/interrupts
entry sensible again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
otherwise we get nasty messages about locks not being released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modularize the write function and reorganaize the internal buffer
management. Remove obsolete chip options and fixup all affected
users.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
increase the year dates to 2006 and bump the version to 1.0.109-k2
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
same as e1000 - remove the changelog from the driver code itself.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
deinline a few large functions as to allow the compiler to pick.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This mimics a change made in the e1000 driver that imitates a slick
tg3 way of avoiding grabbing the lock around restarting the tx queue.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
There seemed to be another bug introduced as well as a performance hit
with the addtion of the sentinel descriptor workaround. Removal of
this workaround appears to prevent the hang. We'll take a risk
and remove it, as we had never seen the originally reported bug
under linux.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
user contributed fix for LAA across down/up, from tonychung00@users.sf.net.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Moved interrupt masking to before requesting the interrupt from the OS.
Moved interrupt enable to after netif_poll_enable. This fixes a racy
BUG() where polling would be running on another CPU at the same time
that netif_poll_enable would run.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
This fixes various odd things that missed update together with cpm_uart
platform_device move. Unified resources names, restructurisation, etc.
Also, addressed issue with recent phys/virt translation rework. Being
cache-coherent, CPM2's do alloc_bootmem() for the console stuff, and it was
used to treat console buffer descriptor mapping 1:1 (as in CPM1 case),
which is definitely wrong.
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
PCI is faked on these devices by SMM traps. Don't depend on that --
check for the chipset directly instead.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
If a SIR dongle is built in the kernel while IRTTY_SIR is built
as a module, kernel compilation will fail.
Thus, the SIR dongle config should depend on the IRTTY_SIR.
Closes kernel bug# 6512
(http://bugzilla.kernel.org/show_bug.cgi?id=6512)
Signed-off-by: Samuel Ortiz <samuel@sortiz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o modify the rx refill logic and tail bump
o add counter for failures
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Removing readv from struct mtd_info broke block2mtd. Remove the
reference and the useless default implementation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Split the core of the read function out and implement
seperate handling functions for software and hardware
ECC.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The nand driver has a superflous read ready / command
delay in the read functions. This was added to handle
chips which have an automatic read forward. Newer
chips do not have this functionality anymore. Add this
option to avoid the delay / I/O operation. Mark all
large page chips with the new option flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The lock simplifying patch did not move the lock and waitqueue
initialization into the controller allocation patch.
This reinitializes waitqueue and spinlocks also for driver
supplied controller stuctures. Move it into the allocation path.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Mixing "depends on I2C" and "select I2C" within the media subsystem
leads to the following problem:
Warning! Found recursive dependency: I2C DVB_BUDGET DVB_BUDGET_PATCH
DVB_AV7110 VIDEO_SAA7146_VV VIDEO_SAA7146 I2C
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we post a list of length exactly a multiple of 256, nreq in
doorbell gets set to 256 which is wrong: it should be encoded by 0.
This is because we only zero it out on the next WR, which may not be
there. The solution is to ring the doorbell after posting a WQE, not
before posting the next one.
This is the same bug that we just fixed for QPs with non-shared RQ.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IB/ipath: deref correct pointer when using kernel SMA
IB/ipath: fix null deref during rdma ops
IB/ipath: register as IB device owner
IB/ipath: enable PE800 receive interrupts on user ports
IB/ipath: enable GPIO interrupt on HT-460
IB/ipath: fix NULL dereference during cleanup
IB/ipath: replace uses of LIST_POISON
IB/ipath: fix reporting of driver version to userspace
IB/ipath: don't modify QP if changes fail
IB/ipath: fix spinlock recursion bug
* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/libata-dev:
[PATCH] libata: add pio flush for via atapi (was: Re: TR: ASUS A8V Deluxe, x86_64)
md->disk was being used in a debug message before it was allocated.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
new SMSC LAN83C185 10BaseT/100BaseTX PHY driver for the PHY subsystem
Signed-off-by: Herbert Valerio Riedel <hvr@gnu.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
