For the common, open coded 'skb->nh.raw = skb->data' operation, so that we can
later turn skb->nh.raw into a offset, reducing the size of struct sk_buff in
64bit land while possibly keeping it as a pointer on 32bit.
This one touches just the most simple case, next will handle the slightly more
"complex" cases.
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Where appropriate, convert references to xtime.tv_sec to the
get_seconds() helper function.
Signed-off-by: James Morris <jmorris@namei.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Expose IPSEC modes output path to take an xfrm state as input param.
This makes it consistent with the input mode processing (which already
takes the xfrm state as a param).
Signed-off-by: Jamal Hadi Salim <hadi@cyberus.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>
With this patch transformation state is updated last used time
for each sending. Xtime is used for it like other state lifetime
expiration.
Mobile IPv6 enabled nodes will want to know traffic status of each
binding (e.g. judgement to request binding refresh by correspondent node,
or to keep home/care-of nonce alive by mobile node).
The last used timestamp is an important hint about it.
Based on MIPL2 kernel patch.
This patch was also written by: Henrik Petander <petander@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
On current kernel, ip6_find_1stfragopt() is used by IPv6 IPsec to find
offset to be inserted header in outbound for transport mode. (BTW, no
usage may be needed for IPv4 case.) Mobile IPv6 requires another
logic for routing header and destination options header
respectively. This patch is common platform for the offset and adopts
it to IPsec.
Based on MIPL2 kernel patch.
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Transformation mode is used as either IPsec transport or tunnel.
It is required to add two more items, route optimization and inbound trigger
for Mobile IPv6.
Based on MIPL2 kernel patch.
This patch was also written by: Ville Nuorvala <vnuorval@tcs.hut.fi>
Signed-off-by: Masahide NAKAMURA <nakam@linux-ipv6.org>
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace CHECKSUM_HW by CHECKSUM_PARTIAL (for outgoing packets, whose
checksum still needs to be completed) and CHECKSUM_COMPLETE (for
incoming packets, device supplied full checksum).
Patch originally from Herbert Xu, updated by myself for 2.6.18-rc3.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the wrapper function skb_is_gso which can be used instead
of directly testing skb_shinfo(skb)->gso_size. This makes things a little
nicer and allows us to change the primary key for indicating whether an skb
is GSO (if we ever want to do that).
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch segments GSO packets received by the IPsec stack. This can
happen when a NIC driver injects GSO packets into the stack which are
then forwarded to another host.
The primary application of this is going to be Xen where its backend
driver may inject GSO packets into dom0.
Of course this also can be used by other virtualisation schemes such as
VMWare or UML since the tap device could be modified to inject GSO packets
received through splice.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the structure xfrm_mode. It is meant to represent
the operations carried out by transport/tunnel modes.
By doing this we allow additional encapsulation modes to be added
without clogging up the xfrm_input/xfrm_output paths.
Candidate modes include 4-to-6 tunnel mode, 6-to-4 tunnel mode, and
BEET modes.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_me_harder doesn't use the port numbers of the xfrm lookup and
uses ip_route_input for non-local addresses which doesn't do a xfrm
lookup, ip6_route_me_harder doesn't do a xfrm lookup at all.
Use xfrm_decode_session and do the lookup manually, make sure both
only do the lookup if the packet hasn't been transformed already.
Makeing sure the lookup only happens once needs a new field in the
IP6CB, which exceeds the size of skb->cb. The size of skb->cb is
increased to 48b. Apparently the IPv6 mobile extensions need some
more room anyway.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call netfilter hooks before IPsec transforms. Packets visit the
FORWARD/LOCAL_OUT and POST_ROUTING hook before the first encapsulation
and the LOCAL_OUT and POST_ROUTING hook before each following tunnel mode
transform.
Patch from Herbert Xu <herbert@gondor.apana.org.au>:
Move the loop from dst_output into xfrm4_output/xfrm6_output since they're
the only ones who need to it. xfrm{4,6}_output_one() processes the first SA
all subsequent transport mode SAs and is called in a loop that calls the
netfilter hooks between each two calls.
In order to avoid the tail call issue, I've added the inline function
nf_hook which is nf_hook_slow plus the empty list check.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.
Let it rip!
