This patch causes the ignore_normal_resume flag to be set slightly earlier,
before there is a chance that the apm driver will receive the normal resume
event from the BIOS. (Addresses Debian bug #310865)
Signed-off-by: Thomas Hood <jdthood@yahoo.co.uk>
Acked-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/i386/kernel/vsyscall-note.o is not listed as a target so its .cmd file
is neither considered as a target nor is it read on the next build. This
causes vsyscall-note.o to be rebuilt every time that you run make, which
causes vmlinux to be rebuilt every time.
Signed-off-by: Keith Owens <kaos@ocs.com.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As mandated by the spec, disable timer around transitions.
From code by : Ken Staton <ken_staton@agilent.com
Signed-off-by: Dave Jones <davej@redhat.com>
The spec states that we have to do this, which is *horrid*.
Based on code from: Ken Staton <ken_staton@agilent.com>
Signed-off-by: Dave Jones <davej@redhat.com>
With the release of the dual-core AMD Opterons last week,
it's high time that cpufreq supported them. The attached
patch applies cleanly to 2.6.12-rc3 and updates powernow-k8
to support the latest Athlon 64 and Opteron processors.
Update the driver to version 1.40.0 and provide support
for dual-core processors.
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Some cpufreq drivers (at that time, only powernow-k7) need to recalibrate the
cpu_khz at runtime.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
We have to recalibrate cpu_khz in order to use the current FID instead the max
FID since some BIOS do not put the processor at maximum frequency at POST.
Also, some BIOS will change the processor frequency at our back after cpu_khz
was calibrate. Finally, this will fix a long standing bug when we do
something like this:
# rmmod powernow-k7
# modprobe powernow-k7
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dave Jones <davej@redhat.com>
The speedstep-smi driver actually works on >=1 notebook with a
Pentium 4-M CPU where all other cpufreq drivers fail. Therefore,
allow speedstep-smi on P4Ms again, but warn users of likely failure
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
The Pentium 4 - Ms (HT) with CPUID 0xF34 and 0xF41 seem to support
centrino-like enhanced speedstep; however, no "table" support is possible.
Therefore, put NULL entries into speedstep-centrino.c
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Dave Jones <davej@redhat.com>
This is a neverending story
linux/acpi.h contains empty declarations for acpi_boot_init() &
acpi_boot_table_init() but they are nested inside #ifdef CONFIG_ACPI.
So we'll have to #ifdef in arch/i386/kernel/setup.c: setup_arch()
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Cc: "Brown, Len" <len.brown@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes 'smp_num_siblings' value on the systems with a buggy bios,
which sets number of siblings to '2' even when HT is disabled. (more
details are at http://bugzilla.kernel.org/show_bug.cgi?id=4359)
I am planning to do more cleanup in this area (like moving smp_num_siblings
to per cpuinfo) shortly.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
num_cache_leaves is used in __devexit cache_remove_dev() and can therefore
not be __devinit.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove duplicated ifdef
- Make core_id match what Intel uses
- Initialize phys_proc_id correctly for non DC case
- Handle non power of two core numbers.
Fixes for both i386 and x86-64
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Last round hopefully of cpu_core_id changes hopefully fow now:
- Always initialize cpu_core_id for all CPUs, even when no dual core setup
is detected. This prevents funny /proc/cpuinfo output
- Do the same with phys_proc_id[] even when no HyperThreading - dito.
- Use the CPU APIC-ID from CPUID 1 instead of the linux virtual CPU number
to identify the core for AMD dual core setups.
Patch for i386/x86-64.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kprobes could not handle the insertion of a probe on the ret/lret
instruction and used to oops after single stepping since kprobes was
modifying eip/rip incorrectly. Adjustment of eip/rip is not required after
single stepping in case of ret/lret instruction, because eip/rip points to
the correct location after execution of the ret/lret instruction. This
patch fixes the above problem.
Signed-off-by: Prasanna S Panchamukhi <prasanna@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In include/asm-x86_64/string.h there are such comments:
/* Use C out of line version for memcmp */
#define memcmp __builtin_memcmp
int memcmp(const void * cs,const void * ct,size_t count);
This would mean that if the compiler does not decide to use __builtin_memcmp,
it emits a call to memcmp to be satisfied by the C out-of-line version in
lib/string.c. What happens is that after preprocessing, in lib/string.i you
may find the definition of "__builtin_strcmp".
Actually, by accident, in the object you will find the definition of strcmp
and such (maybe a trick intended to redirect calls to __builtin_memcmp to the
default memcmp when the definition is not expanded); however, this particular
case is not a documented feature as far as I can see.
Also, the EXPORT_SYMBOL does not work, so it's duplicated in the arch.
I simply added some #undef to lib/string.c and removed the (now duplicated)
exports in x86-64 and UML/x86_64 subarchs (the second ones are introduced by
another patch I just posted for -mm).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
CC: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The recent change fix-crash-in-entrys-restore_all.patch
childregs->esp = esp;
p->thread.esp = (unsigned long) childregs;
- p->thread.esp0 = (unsigned long) (childregs+1);
+ p->thread.esp0 = (unsigned long) (childregs+1) - 8;
p->thread.eip = (unsigned long) ret_from_fork;
introduces an inconsistency between esp and esp0 before the task is run the
first time. esp0 is no longer the actual start of the stack, but 8 bytes
off.
This shows itself clearly in a scenario when a ptracer that is set to also
ptrace eventual children traces program1 which then clones thread1. Now
the ptracer wants to modify the registers of thread1. The x86 ptrace
implementation bases it's knowledge about saved user-space registers upon
p->thread.esp0. But this will be a few bytes off causing certain writes to
the kernel stack to overwrite a saved kernel function address making the
kernel when actually running thread1 jump out into user-space. Very
spectacular.
The testcase I've used is:
/* start with strace -f ./a.out */
#include <pthread.h>
#include <stdio.h>
void *do_thread(void *p)
{
for (;;);
}
int main()
{
pthread_t one;
pthread_create(&one, NULL, &do_thread, NULL);
for (;;);
return 0;
}
So, my solution is to instead of just adjusting esp0 that creates an
inconsitent state I adjust where the user-space registers are saved with -8
bytes. This gives us the wanted extra bytes on the start of the stack and
esp0 is now correct. This solves the issues I saw from the original
testcase from Mateusz Berezecki and has survived testing here. I think
this should go into -mm a round or two first however as there might be some
cruft around depending on pt_regs lying on the start of the stack. That
however would have broken with the first change too!
It's actually a 2-line diff but I had to move the comment of why the -8 bytes
are there a few lines up. Thanks to Zwane for helping me with this.
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Another large rollup of various patches from Adrian which make things static
where they were needlessly exported.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert most of the current code that uses _NSIG directly to instead use
valid_signal(). This avoids gcc -W warnings and off-by-one errors.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There were still a few comments left refering to verify_area, and two
functions, verify_area_skas & verify_area_tt that just wrap corresponding
access_ok_skas & access_ok_tt functions, just like verify_area does for
access_ok - deprecate those.
There was also a few places that still used verify_area in commented-out
code, fix those up to use access_ok.
After applying this one there should not be anything left but finally
removing verify_area completely, which will happen after a kernel release
or two.
Signed-off-by: Jesper Juhl <juhl-lkml@dif.dk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Arrange for all kernel printks to be no-ops. Only available if
CONFIG_EMBEDDED.
This patch saves about 375k on my laptop config and nearly 100k on minimal
configs.
Signed-off-by: Matt Mackall <mpm@selenic.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Split the i386 entry.S files into entry.S and syscall_table.S which is
included in the previous one (so actually there is no difference between them)
and use the syscall_table.S in the UML build, instead of tracking by hand the
syscall table changes (which is inherently error-prone).
We must only insert the right #defines to inject the changes we need from the
i386 syscall table (for instance some different function names); also, we
don't implement some i386 syscalls, as ioperm(), nor some TLS-related ones
(yet to provide).
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch solves VM86 interrupt emulation deadlock on SMP systems. The VM86
interrupt emulation has been heavily tested and works well on UP systems
after last update, but it seems to deadlock when we have used it on SMP/HT
boxes now.
It seems, that disable_irq() cannot be called from interrupts, because it
waits until disabled interrupt handler finishes
(/kernel/irq/manage.c:synchronize_irq():while(IRQ_INPROGRESS);). This
blocks one CPU after another. Solved by use disable_irq_nosync.
There is the second problem. If IRQ source is fast, it is possible, that
interrupt is sometimes processed and re-enabled by the second CPU, before
it is disabled by the first one, but negative IRQ disable depths are not
allowed. The spinlocking and disabling IRQs over call to
disable_irq_nosync/enable_irq is the only solution found reliable till now.
Signed-off-by: Michal Sojka <sojkam1@control.felk.cvut.cz>
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
http://bugme.osdl.org/show_bug.cgi?id=4426
vendor_id : AuthenticAMD
cpu family : 6
model : 10
model name : AMD Athlon(tm) XP
stepping : 0
cpu MHz : 2204.807
<snipped>
cpuid level : 1
wp : yes
flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov
pat pse36 mmx fxsr sse pni syscall mmxext 3dnowext 3dnow
bogomips : 4358.14
We're marking bit 0 of extended function 0x80000001 cpuid as PNI support on
AMD processors, when it actually denotes x87 FPU present. Patch for i386
and x86_64 below.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the i386 HPET code assumes the entire HPET implementation from
the spec is present. This breaks on boxes that do not implement the
optional legacy timer replacement functionality portion of the spec.
This patch, which is very similar to my x86-64 patch for the same issue,
fixes the problem allowing i386 systems that cannot use the HPET for the
timer interrupt and RTC to still use the HPET as a time source. I've
tested this patch on a system systems without HPET, with HPET but without
legacy timer replacement, as well as HPET with legacy timer replacement.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Enable write combining for server works LE rev > 6 per
http://www.ussg.iu.edu/hypermail/linux/kernel/0104.3/1007.html
Signed-Off-By: Lee Revell <rlrevell@joe-job.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
do_debug() and do_int3() return void.
This patch fixes the CONFIG_KPROBES variant of do_int3() to return void too
and adjusts entry.S accordingly.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch by Jaya Kumar introduces a generic infrastructure to deal with
x86 chipsets with nonstandard reset sequences, and adds support for the
Geode gx1/cs5530a chipset.
Signed-off-by: Jaya Kumar <jayalk@intworks.biz>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bug against an xSeries system showed up recently noting that the
check_nmi_watchdog() test was failing.
I have been investigating it and discovered in both i386 and x86_64 the
recent change to the routine to use the cpu_callin_map has uncovered a
problem. Prior to that change, on an SMP box, the test was trivally
passing because all cpu's were found to not yet be online, but now with the
callin_map they are discovered, it goes on to test the counter and they
have not yet begun to increment, so it announces a CPU is stuck and bails
out.
On all the systems I have access to test, the announcement of failure is
also bougs... by the time you can login and check /proc/interrupts, the
NMI count is happily incrementing on all CPUs. Its just that the test is
being done too early.
I have tried moving the call to the test around a bit, and it was always
too early. I finally hit on this proposed solution, it delays the routine
via a late_initcall(), seems like the right solution to me.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new i386/x86_64 assemblers no longer accept instructions for moving
between a segment register and a 32bit memory location, i.e.,
movl (%eax),%ds
movl %ds,(%eax)
To generate instructions for moving between a segment register and a
16bit memory location without the 16bit operand size prefix, 0x66,
mov (%eax),%ds
mov %ds,(%eax)
should be used. It will work with both new and old assemblers. The
assembler starting from 2.16.90.0.1 will also support
movw (%eax),%ds
movw %ds,(%eax)
without the 0x66 prefix. I am enclosing patches for 2.4 and 2.6 kernels
here. The resulting kernel binaries should be unchanged as before, with
old and new assemblers, if gcc never generates memory access for
unsigned gsindex;
asm volatile("movl %%gs,%0" : "=g" (gsindex));
If gcc does generate memory access for the code above, the upper bits
in gsindex are undefined and the new assembler doesn't allow it.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This makes a trap on the 'iret' that returns us to user space
cause a nice clean SIGSEGV, instead of just a hard (and silent)
exit.
That way a debugger can actually try to see what happened, and
we also properly notify everybody who might be interested about
us being gone.
This loses the error code, but tells the debugger what happened
with ILL_BADSTK in the siginfo.
We were calling ptrace_notify() after auditing the syscall and arguments,
but the debugger could have _changed_ them before the syscall was actually
invoked. Reorder the calls to fix that.
While we're touching ever call to audit_syscall_entry(), we also make it
take an extra argument: the architecture of the syscall which was made,
because some architectures allow more than one type of syscall.
Also add an explicit success/failure flag to audit_syscall_exit(), for
the benefit of architectures which return that in a condition register
rather than only returning a single register.
Change type of syscall return value to 'long' not 'int'.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch to arch/i386/kernel/cpu/amd.c relies on the variable
cpu_core_id which is defined in i386/kernel/smpboot.c. This means it is
only present if CONFIG_X86_SMP is defined, not CONFIG_SMP (alternative
SMP harnesses won't have it, which is why it breaks voyager).
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Randy please double check especially this one.
there may be a better solution.
Fix efi section references:
remove __initdata for struct efi efi_phys
and struct efi_memory_map memmap
Error: ./arch/i386/kernel/efi.o .text refers to 000000d3 R_386_32
.init.data
Error: ./arch/i386/kernel/efi.o .text refers to 000000ff R_386_32
.init.data
efi_memmap_walk (which is not __init nor static)
accesses both efi_phys and memmap.
Signed-off-by: maximilian attems <janitor@sternwelten.at>
Acked-by: Randy Dunlap <rddunlap@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I thought I'm done with fixing u32 vs. pm_message_t ... unfortunately
that turned out not to be the case as Russel King pointed out. Here are
fixes for Documentation and common code (mainly system devices).
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- broken sibling_map setup in x86_64
- grouping all the core and HT related cpuinfo fields.
We are reasonably sure that adding new cpuinfo fields after "siblings" field,
will not cause any app failure. Thats because today's /proc/cpuinfo
format is completely different on x86, x86_64 and we haven't heard of any
x86 app breakage because of this issue. Grouping these fields will
result in more or less common format on all architectures (ia64, x86 and
x86_64) and will cause less confusion.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Clean up the code greatly. Now uses the infrastructure from the Intel dual
core patch Should fix a final bug noticed by Tyan of not detecting the nodes
correctly in some corner cases.
Patch for x86-64 and i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Appended patch adds the support for Intel dual-core detection and displaying
the core related information in /proc/cpuinfo.
It adds two new fields "core id" and "cpu cores" to x86 /proc/cpuinfo and the
"core id" field for x86_64("cpu cores" field is already present in x86_64).
Number of processor cores in a die is detected using cpuid(4) and this is
documented in IA-32 Intel Architecture Software Developer's Manual (vol 2a)
(http://developer.intel.com/design/pentium4/manuals/index_new.htm#sdm_vol2a)
This patch also adds cpu_core_map similar to cpu_sibling_map.
Slightly hacked by AK.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We need to use the size_and_mask in set_mtrr_var_ranges(which is called
while programming MTRR's for AP's
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
