Remove all the useless __func__ prefixes in debug messages,
and replace the DPRINTF macro with a function.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I mistakenly changed retry count passed in rtl8187_tx in previous change
"rtl8187: feedback transmitted packets using tx close descriptor for
8187B". For 8187 it should represent the number of retries (retry count
limit). As explained by Johannes Berg, .count represents the number of
tries (not retries), and retries = tries - 1.
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Tested-by: Hin-Tak Leung <htl10@users.sourceforge.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to pad the header so no constant needed for that,
no need to carry any version number from netbsd nor CVS
IDs from them.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Hostapd now passes the HT parameters through the config()
callback, use these to set the appropriate channel in AP mode.
Signed-off-by: Sujith <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For mac revisions >= "Griffin," the hardware allows the mic tx and rx
authenticator keys to share the same cache line, whereas earlier
hardware can only store the rx. Enable the combined mic on hardware
that supports it.
Changes to ath5k.h
Changes-licensed-under: 3-Clause-BSD
Changes to attach.c, pcu.c, reg.h
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Status: O
With the addition of TKIP (and soon CCMP), key->alg is a more useful
guide to key type than the key length.
This patch cleans up key type assignment in ath5k_hw_set_key by
extracting it into its own function. It also replaces the separate
memcpy() calls for extracting key material into the hardware format
with a loop that works regardless of key size.
Finally, the patch removes support for WEP-128 since it is a
non-standard key length that mac80211 also doesn't use.
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In some cases we would like to set the mac address without changing
the operating mode. However, Atheros cards store PCU data in the high
16 bits of the mac address register. Change ath5k_hw_set_lladdr() to
not clobber the PCU settings.
Changes-licensed-under: ISC
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The base versions handle constant folding just fine.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ISA support in smc91x is incomplete. I doubt there're any smc91x isa card.
This driver is greatly used on arm pxa platforms. Hence we remove the
isa stuff from smc91x driver.
Signed-off-by: Luotao Fu <lfu@pengutronix.de>
Acked-by: Steve Glendinning <steve.glendinning@smsc.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
-m486, -O6 are partircularly amusing.
Remove some other useless lines near as well.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another device using 8390 library that needs converting.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bea3348eef
"[NET]: Make NAPI polling independent of struct net_device objects."
made NAPI polling to be independent of net_device.
So e1000_adapter->polling_netdev is no longer used.
Kill it.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Seems the ixgbe's code was copied from e1000.
The comment talks about something not exist.
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although the hardware supports the 64bit DMA address in design,
but later found that it actually not working.
This patch reduced the rang to 32bit.
Found-by: "Ethan" <ethanhsiao@jmicron.com>
Signed-off-by: "Guo-Fu Tseng" <cooldavid@cooldavid.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to the hardware design, except the first chip on the market,
other chips needs to setup the clock source for MAC processor
implicitly through Global Host Control Register(GHC).
(Strange design huh?)
10/100M uses the PCI-E as clock source, and 1G uses GPHY.
And I reordered the code a little, to make it easier to read.
Found-by: "Ethan" <ethanhsiao@jmicron.com>
Fixed-by: "akeemting" <akeem@jmicron.com>
Signed-off-by: "Guo-Fu Tseng" <cooldavid@cooldavid.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Simply replace netdev->priv with netdev_priv().
Signed-off-by: Wang Chen <wangchen@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bring the physical link down when the interface is down by placing the PHY
in power-down state, unless WOL is enabled. This mirrors the behavior of
other drivers including e1000 and tg3.
Without the patch, ifconfig down leaves the physical link up, which confuses
datacenter users who expect the link lights both on the NIC and the switch to
go out when they bring an interface down.
Furthermore, even though the phy is powered on, autonegotiation stops working,
so a normally gigabit link might suddenly become 100 Mbit half-duplex when the
interface goes down, and become gigabit when it comes up again.
Ayaz said:
I would not include this patch until further testing is performed. NVIDIA
MCP chips use 3rd party PHY vendors. By powering down the phy, it could
have adverse affects on certain phys.
Arthur Jones said:
I just ran across this patch. Tested on a Marvell 88E1121R (GigE PHY)
and works great. This is a very important feature for me.
Signed-off-by: Ed Swierk <eswierk@arastra.com>
Tested-by: Arthur Jones <ajones@riverbed.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Another related 8390 driver. Since this is for nubus, not sure if
anyone still has the hardware?
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix build of ARM etherh driver with new net_device_ops.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't really have a max tx packet size limit, so allow configuring
the device with up to 64k tx MTU.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Fix MTT leakage in resize CQ
IB/ehca: Fix problem with generated flush work completions
IB/ehca: Change misleading error message on memory hotplug
mlx4_core: Save/restore default port IB capability mask
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/paulus/powerpc:
powerpc: Fix system calls on Cell entered with XER.SO=1
powerpc/cell: Fix GDB watchpoints, again
powerpc/mpic: Don't reset affinity for secondary MPIC on boot
powerpc/cell/axon-msi: Retry on missing interrupt
powerpc: Fix boot freeze on machine with empty memory node
powerpc: Fix IRQ assignment for some PCIe devices
powerpc/spufs: Fix spinning in spufs_ps_fault on signal
powerpc/mpc832x_rdb: fix swapped ethernet ids
powerpc: Use generic PHY driver for Marvell 88E1111 PHY on GE Fanuc SBC610
powerpc/85xx: L2 cache size wrong in 8572DS dts
powerpc/virtex: Update defconfigs
powerpc/52xx: update defconfigs
xsysace: Fix driver to use resource_size_t instead of unsigned long
powerpc/virtex: fix various format/casting printk mismatches
powerpc/mpc5200: fix bestcomm Kconfig dependencies
powerpc/44x: Fix 460EX/460GT machine check handling
powerpc/40x: Limit allocable DRAM during early mapping
... by giving the instances' names magic suffix recognized by modpost ;-/
Their ->probe() is __devinit
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
a) ->probe() can be __devinit; no need to put it into .text
b) calling __init stuff from it, OTOH, is wrong
c) ->remove() is __devexit fodder
Acked-by: rmk+kernel@arm.linux.org.uk
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ibmtr_resume() is calling ibmtr_probe(), which is devinit. Whether
that's the right thing to do there is a separate question, but
since it's PCMCIA and thus will never compile without HOTPLUG...
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
pppol2tp_sock_to_session() do sock_hold() if the session to release is
not NULL.
Signed-off-by: Frédéric Moulins <frederic.moulins@alsatis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function is_pure_response() does "ntohl(var) & const" and then
essentially just tests whether the result is 0 or not; this can be done
more efficiently by computing "var & htonl(const)" instead and doing the
byte swap at compile time instead of run time.
This change slightly shrinks the compiled code; eg on x86-64 we save a
couple of bswapl instructions:
add/remove: 0/0 grow/shrink: 0/1 up/down: 0/-8 (-8)
function old new delta
t3_sge_intr_msix_napi 544 536 -8
and this also has the pleasant side effect of fixing a sparse warning:
drivers/net/cxgb3/sge.c:2313:15: warning: restricted degrades to integer
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 7ff93f8b ("mlx4_core: Multiple port type support") introduced
support for different port types. As part of that support, SET_PORT
is invoked to set the port type during driver startup. However, as a
side-effect, for IB ports the invocation of this command also sets the
port's capability mask to zero (losing the default value set by FW).
To fix this, get the default ib port capabilities (via a MAD_IFC Port
Info query) during driver startup, and save them for use in the
mlx4_SET_PORT command when setting the port-type to Infiniband.
This patch fixes problems with subnet manager (SM) failover such as
<https://bugs.openfabrics.org/show_bug.cgi?id=1183>, which occurred
because the IsTrapSupported bit in the capability mask was zeroed.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch adds the STMicroelectronics ste10xp PHY device driver.
It supports both the ste100p and the ste101p devices.
Suspend/resume alredy added.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the power management support into the physical
abstraction layer.
Suspend and resume functions respectively turns on/off the bit 11
into the PHY Basic mode control register.
Generic PHY device starts supporting PM.
In order to support the wake-on LAN and avoid to put in power down
the PHY device, the MDIO is aware of what the Ethernet device wants to do.
Voluntary, no CONFIG_PM defines were added into the sources.
Also generic suspend/resume functions are exported to allow
other drivers use them (such as genphy_config_aneg etc.).
Within the phy_driver_register function, we need to remove the
memset. It overrides the device driver owner and it is not good.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the PHY device driver for the National Semiconductor
DP83865 Gig PHYTER.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
These warning originate from 50014f1 (ne2: convert to
net_device_ops) which did drop those functions.
drivers/net/ne2.c:140: warning: 'ne_open' declared 'static' but never defined
drivers/net/ne2.c:141: warning: 'ne_close' declared 'static' but never defined
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
ixgbe_init_interrupt_scheme() is called from ixgbe_resume(). Build that
with CONFIG_PM and without CONFIG_HOTPLUG and you've got a problem.
Several helpers called by it also are misannotated __devinit.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the calls necessary to enable advanced error reporting for igb on
systems with AER enabled.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The system log messages created on a link status change need to follow a
specific format to work with tools some customers use. This also makes
the messages consistant with other Intel driver link messages.
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
