Support for generic input output for MX1 family.
The implementation prevents allocation of one pin
by two users, but does not store pointer to the user
description permanently, because this solution
would have bigger memory overhead.
The simple way to integrate code with per BSP
pins setup and allocation is required else all GPIO
registration checking is useless. The function
imx_gpio_setup_multiple_pins() can be used for this
purpose in future.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Modify the common at91 hardware support to deal with the non-MMU
at91x40 family. The base RAM (which is most likely not DRAM) is
set to the configured value. Virtual IO device mapping is set
to be 1 to 1 with the physical addresses.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Base at91x40 architecture support defines. These parts are somewhat
simpler than the ARM9 Atmel based parts.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AT91x40 family doesn't have the debug unit like its bigger brothers.
But it does have the ID and extension registers (with the bit meanings
the same). Reorganize at91_dbgu.h to cater for this.
This also affects the load uncompressor, since it outputs to the
debug port.
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Register the GPIO-connected buttons on the SAM9261-EK board as a
"gpio-keys" platform device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add board-specific setup for the LCD on the Atmel AT91SAM9261-EK and
AT91SAM9263-EK boards.
Signed-off-by: Nicolas Ferre <nicolas.ferre@rfo.atmel.com>
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the partition layout on the revision B
modules which have large page NAND fitted.
The new partition table accounts for the use of the
128KiB block parts, which means the second partition
on the device is moved to the new boundary.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add resources for the AX88796 on the Simtec BAST.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the partition layour used on the
revision B modules which ship with large page NAND
flash as default.
The differnce between the old and new layouts is that
the large page devices use 128KiB blocks, so the
initial loader partition now ends at 128KiB boundary
pushing the begining of partition 1 up. The rest of
the partitions are in the same place as the small page
NAND devices.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add resources for the SM501 present on the
Simtec Anubis board, including the framebuffer
and the I2C for DDC.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds the resources necessary for the
AX88796 driver to attach to the AX88796 network
controller fitted on the Simtec Anubis board.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support pin multiplexing configurations driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support GPIO driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarino@ru.mvista.com>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support clock control driver for TI DaVinci SoC
Signed-off-by: Vladimir Barinov <vbarinov@ru.mvista.com>
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
However there are similar things in the EBIU_DDRQUE Register
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
we converted to using a system call for userspace spinlocks
rather than a dedicated exception long ago
Signed-off-by: Mike Frysinger <michael.frysinger@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
These changes will make NetLabel behave like labeled IPsec where there is an
access check for both labeled and unlabeled packets as well as providing the
ability to restrict domains to receiving only labeled packets when NetLabel
is in use. The changes to the policy are straight forward with the
following necessary to receive labeled traffic (with SECINITSID_NETMSG
defined as "netlabel_peer_t"):
allow mydom_t netlabel_peer_t:{ tcp_socket udp_socket rawip_socket } recvfrom;
The policy for unlabeled traffic would be:
allow mydom_t unlabeled_t:{ tcp_socket udp_socket rawip_socket } recvfrom;
These policy changes, as well as more general NetLabel support, are included
in the SELinux Reference Policy SVN tree, r2352 or later. Users who enable
NetLabel support in the kernel are strongly encouraged to upgrade their
policy to avoid network problems.
Signed-off-by: Paul Moore <paul.moore@hp.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add a new security check on mmap operations to see if the user is attempting
to mmap to low area of the address space. The amount of space protected is
indicated by the new proc tunable /proc/sys/vm/mmap_min_addr and defaults to
0, preserving existing behavior.
This patch uses a new SELinux security class "memprotect." Policy already
contains a number of allow rules like a_t self:process * (unconfined_t being
one of them) which mean that putting this check in the process class (its
best current fit) would make it useless as all user processes, which we also
want to protect against, would be allowed. By taking the memprotect name of
the new class it will also make it possible for us to move some of the other
memory protect permissions out of 'process' and into the new class next time
we bump the policy version number (which I also think is a good future idea)
Acked-by: Stephen Smalley <sds@tycho.nsa.gov>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
Inode numbers are unsigned long and so need to %lu as format string of printf.
Signed-off-by: Tobias Oed <tobias.oed@octant-fr.com>
Signed-off-by: James Morris <jmorris@namei.org>
In security_get_user_sids, move the transition permission checks
outside of the section holding the policy rdlock, and use the AVC to
perform the checks, calling cond_resched after each one. These
changes should allow preemption between the individual checks and
enable caching of the results. It may however increase the overall
time spent in the function in some cases, particularly in the cache
miss case.
The long term fix will be to take much of this logic to userspace by
exporting additional state via selinuxfs, and ultimately deprecating
and eliminating this interface from the kernel.
Tested-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Stephen Smalley <sds@tycho.nsa.gov>
Signed-off-by: James Morris <jmorris@namei.org>
During the LSPP testing we found that it was possible for
policydb_destroy() to take 10+ seconds of kernel time to complete.
Basically all policydb_destroy() does is walk some (possibly long) lists
and free the memory it finds. Turning off slab debugging config options
made the problem go away since the actual functions which took most of
the time were (as seen by oprofile)
> 121202 23.9879 .check_poison_obj
> 78247 15.4864 .check_slabp
were caused by that. So I decided to also add some voluntary schedule
points in that code so config voluntary preempt would be enough to solve
the problem. Something similar was done in places like
shmem_free_pages() when we have to walk a list of memory and free it.
This was tested by the LSPP group on the hardware which could reproduce
the problem just loading a new policy and was found to not trigger the
softlock detector. It takes just as much processing time, but the
kernel doesn't spend all that time stuck doing one thing and never
scheduling.
Someday a better way to handle memory might make the time needed in this
function a lot less, but this fixes the current issue as it stands
today.
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: James Morris <jmorris@namei.org>
The structure is as follows (relative to selinuxfs root):
/class/file/index
/class/file/perms/read
/class/file/perms/write
...
Each class is allocated 33 inodes, 1 for the class index and 32 for
permissions. Relative to SEL_CLASS_INO_OFFSET, the inode of the index file
DIV 33 is the class number. The inode of the permission file % 33 is the
index of the permission for that class.
Signed-off-by: Christopher J. PeBenito <cpebenito@tresys.com>
Signed-off-by: James Morris <jmorris@namei.org>
Specify the inode counter explicitly in sel_make_dir(), rather than always
using sel_last_ino.
Signed-off-by: Christopher J. PeBenito <cpebenito@tresys.com>
Signed-off-by: James Morris <jmorris@namei.org>
sel_remove_bools() will also be used by the object class discovery, rename
it for more general use.
Signed-off-by: Christopher J. PeBenito <cpebenito@tresys.com>
Signed-off-by: James Morris <jmorris@namei.org>
Add support to the SELinux security server for obtaining a list of classes,
and for obtaining a list of permissions for a specified class.
Signed-off-by: Christopher J. PeBenito <cpebenito@tresys.com>
Signed-off-by: James Morris <jmorris@namei.org>
This patch adds a missing NVRAM strapping for 5755 devices.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds automatic MDI crossover support when autonegotiation is
turned off. Automatic MDI crossover allows link to be established
without the use of a crossover cable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For most pre-5705 devices, multiple link interrupts were being generated
for a single physical link change. The source of the interrupts was
determined to be unnecessary toggling of the MAC link polarity bit.
This patch changes the way the link polarity bit gets configured. Where
possible, code that dynamically configures the bit in response to link
changes has been replaced by code that configures the bit once during
initialization time and then leaves the bit alone.
For correctness, this patch also limits the use of the bit to those
devices where it is defined, namely devices before the 5705. This patch
also corrects the link polarity configurations for 5700 devices when
paired against a bcm5411 phy.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Gagan Arneja <gaagaan@gmail.com> pointed out that tg3_reset_task()
could potentially race with another thread calling tg3_full_lock()
such as the ethtool_set_xxx() functions. This may trigger the
BUG_ON() in tg3_irq_quiesce() or cause the irq_sync flag to be out-
of-sync.
I think the easiest way to fix this is to get the tp->lock first
before setting the irq_sync flag. This is safe to do because the
tp->lock is never grabbed by the irq handler. This change will
guarantee that the irq_sync flag updates will be serialized. We also
have to change one spot to call tg3_netif_start() (which clears the
irq_sync flag) before releasing the tp->lock.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switch from formatting messages in probe routine and copying with
kfifo, to using a small circular queue of information and formatting
on read. This avoids wraparound issues with kfifo, and saves one
copy.
Also make sure to state correct license, rather than copying off some
other driver I started with.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Drivers need to validate the initial addresses in their netlink attribute
validation function or manually reject them if they can't support this.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
All drivers need to unregister their devices in the module unload function.
While doing so they must hold the rtnl and atomically unregister the
rtnl_link ops as well. This makes the rtnl_link_unregister function that
takes the rtnl itself completely useless.
Provide default newlink/dellink functions, make __rtnl_link_unregister and
rtnl_link_unregister unregister all devices with matching rtnl_link_ops and
change the existing users to take advantage of that.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
