Patch from Richard Purdie
This patch updates the PCMCIA pxa2xx_sharpsl driver to support multiple scoop
devices by adding a scoop to pcmcia slot mapping structure. It adds platform
support for poodle, is known to work on spitz (which is dual slot) and
should also support collie with a minor amount of further work.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The n30 machine file is using a kernel thread to change the
state of the USB D+ pull-up resistor, which is not the proper
way to do this. Once the usb-gadget support for the 24xx is
merge, the proper access method will be added.
This patch also removes the problem of using HZ for the
msleep calls, from Nishanth Aravamudan.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Drop the I2C_ACK_TEST ioctl, which was commented out. It never really
existed (not after 1999 anyway), and there is no such thing as a ack
test on I2C/SMBus anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pc87360: consolidate fan helper
This patch consolidates the _set_fan_min() helper routine into the 2
line sysfs-callback wrapper that uses it.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
pc87360: number-skew to init
The temp, therm, fan, pwm callbacks all have an offset skew in the code
which accommodates attribute numbering conventions under
/sys/bus/i2c/devices/9191-6620/ (ie they start at 1)
This patch moves that skew into the declaration, and out of the
functions (except for therm, where we simplify from 2 skews to 1). The
declarative skew is clearer, less error-prone, and more efficient.
The use of 11+offset-4 below reflects the fact that the sysfs numbering
of these units is 4, 5, 6, but they use internal VLM units 11, 12, 13 to
measure the thermistor voltages.
There's one remaining skew factor, in *_crit callbacks below, because
there are no critical thresholds for voltages 0-10, only for those
supporting the thermistors.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the new "dynamic sysfs callbacks", as introduced recently by Yani
Ioannou, in pc87360.
Note that this change isn't indiscriminate. Only those attributes that
would benefit from having an index (i.e., those which are
macro-repeated) have been converted.
This significantly shrinks the size of the module:
before: 49235 drivers/hwmon/pc87360.ko
after: 32532 drivers/hwmon/pc87360.ko
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The sgi_xfer function returns 0 on success instead of the number of
transfered messages as it is supposed to. This patch fixes that.
Let's just hope that no client chip driver was relying on this
misbehavior.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
When an i2c transfer is successful, an incorrect value is returned.
This patch fixes that.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The i2c-keywest driver has a "probe" module parameter which enables bus
scanning at load time. This can be done in userspace with the i2cdetect
tool (part of the lm_sensors package) instead. What's more, i2cdetect
gives more control on the way the bus is scanned, and is safer
(i2c-keywest currently scans reserved addresses and doesn't properly
handle the famous 24RF08 corruption case.)
Thus, I would propose that this module parameter be simply dropped.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The pcilynx driver includes code to dump the contents of an i2c eeprom
for debugging purposes. The same can be done from userspace using the
i2cdump tool (part of the lm_sensors project) instead, in a more
efficient and flexible way.
Thus I would suggest that this functionality be simply dropped from the
pcilynx driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I2C_DEVNAME and i2c_clientname were introduced in 2.5.68 [1] to help
media/video driver authors who wanted their code to be compatible with
both Linux 2.4 and 2.6. The cause of the incompatibility has gone since
[2], so I think we can get rid of them, as they tend to make the code
harder to read and longer to preprocess/compile for no more benefit.
I'd hope nobody seriously attempts to keep media/video driver compatible
across Linux trees anymore, BTW.
[1] http://marc.theaimsgroup.com/?l=linux-kernel&m=104930186524598&w=2
[2] http://www.linuxhq.com/kernel/v2.6/0-test3/include/linux/i2c.h
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that the hardware monitoring drivers are no more part of the i2c
subsystem, they probably deserve their own entry in MAINTAINERS.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete an outdated comment about i2c_algorithm.id being computed
from algo->id.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The I2C_ALGO_* constants have no more users, delete them. Also update
the comments in i2c-id.h so that they reflect the current state of the
file.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In theory, there should be no more users of I2C_ALGO_* at this point.
However, it happens that several drivers were using I2C_ALGO_* for
adapter ids, so we need to correct these before we can get rid of all
the I2C_ALGO_* definitions.
Note that this also fixes a bug in media/video/tvaudio.c:
/* don't attach on saa7146 based cards,
because dedicated drivers are used */
if ((adap->id & I2C_ALGO_SAA7146))
return 0;
This test was plain broken, as it would succeed for many more adapters
than just the saa7146: any those id would share at least one bit with
the saa7146 id. We are really lucky that the few other adapters we want
this driver to work with did not fulfill that condition.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Merge the algorithm id part (16 upper bits) of the i2c adapters ids
into the definition of the adapters ids directly. After that, we don't
need to OR both ids together for each i2c_adapter structure.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are no more users of i2c_algorithm.id, so we can finally drop
this structure member.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Don't rely on i2c_algorithm.id to alter the i2c adapter's id, use the
I2C_ALGO_* value directly instead, because i2c_algorithm will soon
have no id member no more.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the adapter id rather than the algorithm id to detect the i2c-isa
pseudo-adapter. This saves one level of dereferencing, and the
algorithm ids will soon be gone anyway.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The name member of the i2c_algorithm is never used, although all
drivers conscientiously fill it. We can drop it completely, this
structure doesn't need to have a name.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The 24RF08 corruption would better be prevented at i2c-core level than
at chip driver level, for several reasons:
* The second quick write should happen as soon as possible after the
first one, so as to limit the risk that another command is issued on
the bus inbetween, causing the corruption.
* As a matter of fact, the protection code at driver level was reworked
at least three times already, which proves how hard it is to get it
right there, while it's straightforward at i2c-core level.
* It's easy to add a new driver that would need the protection, and
forget to add it. This did happen already.
* As additional probing addresses can be passed to most i2c chip drivers
as module parameters, virtually every i2c chip driver would need the
protection if we want to be really safe.
* Why duplicate code when we can easily avoid it?
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe was quite complex and slow, so I rewrote it in a more
efficient and hopefully clearer way.
Note that this slightly changes the way the module parameters are
handled. This shouldn't change anything for the most common cases
though.
For one thing, the function now respects the order of the parameters
for address probing. It used to always do lower addresses first. The
new approach gives the user more control.
For another, ignore addresses don't overrule probe addresses anymore.
This could have been restored the way it was at the cost of a few more
lines of code, but I don't think it's worth it. Both lists are given
as module parameters, so a user would be quite silly to specify the
same addresses in both lists. The normal addresses list is the only
one that isn't controlled by a module parameter, thus is the only one
the user may reasonably want to remove an address from.
Another significant change is the fact that i2c_probe() will no more
stop when a detection function returns -ENODEV. Just because a driver
found a chip it doesn't support isn't a valid reason to stop all
probings for this one driver. This closes the long standing lm_sensors
ticket #1807.
http://www2.lm-sensors.nu/~lm78/readticket.cgi?ticket=1807
I updated the documentation accordingly.
In terms of algorithmic complexity, the new code is way better. If
I is the ignore address count, P the probe address count, N the
normal address count and F the force address count, the old code
was doing 128 * (F + I + P + N) iterations max, while the new code
does F + P + ((I+1) * N) iterations max. For the most common case
where F, I and P are empty, this is down from 128 * N to N.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updates the VID entries, so any future
Intel CPU will be detected as unknown rather than 9.0
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use the common vid_from_reg function in lm78 rather than
reimplementing it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I see very little reason why vid_from_reg is inlined. It is not
exactly short, its parameters are seldom known in advance, and it is
never called in speed critical areas. Uninlining it should cause
little performance loss if any, and saves a signficant space as well
as compilation time.
As suggested by Alexey Dobriyan, I am leaving vid_to_reg inline for now,
as it is short and has a single user so far.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Delete DEFAULT_VRM from hwmon-vid.h, it has no more users.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cleanup hwmon-vid a bit, fixing typos, rewording some comments and
reindenting properly at places.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.
Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The i2c_detect function has no more user, delete it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe and i2c_detect now do the exact same thing and operate on
the same data structure, so we can have everyone call i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We now have two identical structures, i2c_address_data in i2c-sensor.h
and i2c_client_address_data in i2c.h. We can kill one of them, I choose
to keep the one in i2c.h as it makes more sense (this structure is not
specific to sensors.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The way i2c-sensor handles forced addresses could be optimized. It
defines a structure (i2c_force_data) to associate a module parameter
with a given kind value, but in fact this kind value is always the
index of the structure in each array it is used in. So this additional
value can be omitted, and still be deduced in the code handling these
arrays.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for kind-forced addresses to i2c_probe, like i2c_detect
has for (essentially) hardware monitoring drivers.
Note that this change will slightly increase the size of the drivers
using I2C_CLIENT_INSMOD, with no immediate benefit. This is a
requirement if we want to merge i2c_probe and i2c_detect though, and
seems a reasonable price to pay in comparison with the previous
cleanups which saved much more than that (such as the i2c-isa cleanup
or the i2c address ranges removal.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remove an unused macro and an outdated comment from the lm85 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move SENSORS_LIMIT from i2c-sensor.h to hwmon.h, as it is in no way
related to i2c.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The debugging messages in i2c-core are more confusing than helpful. Some
lack their trailing newline, some lack a prefix, some are redundant,
some lack precious information. Here is my attempt to introduce some
standardization in there.
I also changed two messages in i2c-dev to make it clear they come from
i2c-dev.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a typo in the i2c documentation: the i2c bus scanning tool found in
lm_sensors is called i2cdetect, not i2c_detect.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I've been running with this patch for a while now, and while I've never
seen it trigger except with buggy hardware I think it is a cleaner way
to handle a busy bus. I had -EBUSY until about 10 minutes ago but -EIO
seems to be what most of the existing algo drivers will return in the
same circumstances.
Signed-off-by: Ian Campbell <icampbell@arcom.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could inline i2c_adapter_id, as it is really, really short. Doing
so saves a few bytes both in i2c-core and in the drivers using this
function.
before after diff
drivers/hwmon/adm1026.ko 41344 41305 -39
drivers/hwmon/asb100.ko 27325 27246 -79
drivers/hwmon/gl518sm.ko 20824 20785 -39
drivers/hwmon/it87.ko 26419 26380 -39
drivers/hwmon/lm78.ko 21424 21385 -39
drivers/hwmon/lm85.ko 41034 40939 -95
drivers/hwmon/w83781d.ko 39561 39514 -47
drivers/hwmon/w83792d.ko 32979 32932 -47
drivers/i2c/i2c-core.ko 24708 24531 -177
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Super-I/O find functions in hardware monitoring drivers can be tagged
__init as they are only called from functions themselves tagged __init.
Two of them (smsc47b397 and w83627ehf) already do, but the other four
of them (it87, pc87360, smsc47m1 and w83627hf) did not.
This saves a few bytes of memory after the drivers are loaded, 192 in
the case of the it87 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.
Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds documentation entry for W83792D chip.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds registration of hwmon class. Tested with help of i2c-stub.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I would like to announce support for W83792D chip. This driver was developed
by Winbond Electronics Corp. I added sysfs attributes callbacks infrastructure
plus various code fixes and codingstyle cleanups. I would like to thank Winbond
for supporting free software.
This patch is against 2.6.13rc3 plus hwmon-class and hwmon-split.
Separate patch for documantation and hwmon class register will follow.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Chunhao Huang <DZShen@Winbond.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the definitions of i2c_is_isa_client and i2c_is_isa_adapter from
i2c.h to i2c-isa.h. Only hybrid drivers still need them.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Kill all uses of i2c_is_isa_adapter except for the hybrid drivers (it87,
lm78, w83781d). The i2c-isa adapter not being registered with the i2c
core anymore, drivers don't have to fear being erroneously attached to
it.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
