The volume-knob widget needs to be set with 0x7f instead of 0xff
for Dell laptops with STAC9228 codec, too, like the previous commit.
Reference: Novell bnc#545013
http://bugzilla.novell.com/show_bug.cgi?id=545013
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On FSC laptops, the sound gets muted gradually when the volume is chnaged.
This is due to the wrong volume-knob widget setup. The delta bit (bit 7)
shouldn't be set for these devices.
This patch adds a new quirk to set the value 0x7f to the widget 0x24
instead of 0xff.
Reference: Novell bnc#546006
http://bugzilla.novell.com/show_bug.cgi?id=546006
Signed-off-by: Takashi Iwai <tiwai@suse.de>
With lots of virtual devices it's easy to generate a lot of
events and chew up the kernel IRQ stack.
Reported-by: hyl <heyongli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Bastian Blank reported a boot crash with stackprotector enabled,
and debugged it back to edx register corruption.
For historical reasons irq enable/disable/save/restore had special
calling sequences to make them more efficient. With the more
recent introduction of higher-level and more general optimisations
this is no longer necessary so we can just use the normal PVOP_
macros.
This fixes some residual bugs in the old implementations which left
edx liable to inadvertent clobbering. Also, fix some bugs in
__PVOP_VCALLEESAVE which were revealed by actual use.
Reported-by: Bastian Blank <bastian@waldi.eu.org>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Cc: Stable Kernel <stable@kernel.org>
Cc: Xen-devel <xen-devel@lists.xensource.com>
LKML-Reference: <4AD3BC9B.7040501@goop.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add cciss_allow_hpsa module parameter. This parameter causes
the cciss driver to ignore any Smart Array devices known to be
supported by the hpsa driver.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Fix multiple calls to pci_release_regions. If cciss_pci_init
fails, it already does any necessary call to pci_release_regions,
so this does not need to be done again in cciss_init_one in that
case.
Signed-off-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
ALC861-VD lenovo model causes overflow of spec->init_verbs entries due to
the recent changes. Simply increase the array size to avoid the overflow.
Reported-by: Luca Tettamanti <kronos.it@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Every time we set a filter, we leak memory allocated by
postfix_append_operand() and postfix_append_op().
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Cc: <stable@kernel.org> # for v2.6.31.x
LKML-Reference: <4AD3D7D9.4070400@cn.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Sync up with latest core changes in the syscalls tracing area:
- tracing: Map syscall name to number (syscall_name_to_nr())
- tracing: Call arch_init_ftrace_syscalls at boot
- tracing: add support tracepoint ids (set_syscall_{enter,exit}_id())
Taken from the s390 change.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This too follows the ARM change, given that the issue at hand applies to
all platforms that implement lazy D-cache writeback.
This fixes up the case when a page mapping disappears between the
flush_dcache_page() call (when PG_dcache_dirty is set for the page) and
the update_mmu_cache() call -- such as in the case of swap cache being
freed early. This kills off the mapping test in update_mmu_cache() and
switches to simply testing for PG_dcache_dirty.
Reported-by: Nitin Gupta <ngupta@vflare.org>
Reported-by: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This follows the ARM change, as SH had all of the same issues:
Make die() better match x86:
- add printing of the last accessed sysfs file
- ensure console_verbose() is called under the lock
- ensure we panic outside of oops_exit()
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This avoids updating the superblock write time when we are mounting
the root file system read/only but we need to replay the journal; at
that point, for people who are east of GMT and who make their clock
tick in localtime for Windows bug-for-bug compatibility, and this will
cause e2fsck to complain and force a full file system check.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Signed-off-by: Jan Kara <jack@suse.cz>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: Prevent AER driver from being loaded on non-root port PCIE devices
PCI: get larger bridge ranges when space is available
PCI: pci.c: fix kernel-doc notation
PCI quirk: TI XIO200a erroneously reports support for fast b2b transfers
PCI PM: Read device power state from register after updating it
PCI: remove pci_assign_resource_fixed()
PCI: PCIe portdrv: remove "-driver" from driver name
The MUSB code relies on platform implementations that currently only
exists for Arm and Blackfin processors, so have the MUSB Kconfig depend
upon those arches.
This should prevent other arches from building MUSB via randconfig.
Reported-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Timechart doesn't work if debugfs is not in /sys/kernel/debug/.
Fixed by using global debugfs_path which is filled in by perf.
Signed-off-by: Ashwin Chaugule <ashwinc@quicinc.com>
Cc: "Arjan van de Ven" <arjan@linux.intel.com>
LKML-Reference: <a751bdc6978478de6d10440e587a2cc7.squirrel@www.codeaurora.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Latest kernel has a kernel panic in booting on i386 machine when
profile=2 setting in cmdline. It is due to 'sp' being incorrect in
profile_pc().
BUG: unable to handle kernel NULL pointer dereference at 00000246
IP: [<c01288b6>] profile_pc+0x2a/0x48
*pde = 00000000
Oops: 0000 [#1] SMP
This differs from the original version by Alex Shi in that we use the
kernel_stack_pointer() inline already defined in <asm/ptrace.h> for
this purpose, instead of #ifdef.
Originally-by: Alex Shi <alex.shi@intel.com>
Cc: "Chen, Tim C" <tim.c.chen@intel.com>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
struct sockaddr_storage * can safely be used as struct sockaddr *.
Suppress an "incompatible pointer type" warning.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 46d57a449a ("serial: use tty_port pointers in the core code")
contained two bugs that causes (rare) crashes:
- the rename typoed one site
- a NULL check was missed
Reported-and-tested-by: Ingo Molnar <mingo@elte.hu>
Cc: Greg KH <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
On ARM, update_mmu_cache() does dcache flush for a page only if
it has a kernel mapping (page_mapping(page) != NULL). The correct
behavior would be to force the flush based on dcache_dirty bit only.
One of the cases where present logic would be a problem is when
a RAM based block device[1] is used as a swap disk. In this case,
we would have in-memory data corruption as shown in steps below:
do_swap_page()
{
- Allocate a new page (if not already in swap cache)
- Issue read from swap disk
- Block driver issues flush_dcache_page()
- flush_dcache_page() simply sets PG_dcache_dirty bit and does not
actually issue a flush since this page has no user space mapping yet.
- Now, if swap disk is almost full, this newly read page is removed
from swap cache and corrsponding swap slot is freed.
- Map this page anonymously in user space.
- update_mmu_cache()
- Since this page does not have kernel mapping (its not in page/swap
cache and is mapped anonymously), it does not issue dcache flush
even if dcache_dirty bit is set by flush_dcache_page() above.
<user now gets stale data since dcache was never flushed>
}
Same problem exists on mips too.
[1] example:
- brd (RAM based block device)
- ramzswap (RAM based compressed swap device)
Signed-off-by: Nitin Gupta <ngupta@vflare.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the trampoline and accessors back out of .cpuinit.* for the
case of 64-bits+ACPI_SLEEP.
This solves s2ram hangs reported in:
http://bugzilla.kernel.org/show_bug.cgi?id=14279
Reported-and-bisected-by: Christian Casteyde <casteyde.christian@free.fr>
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Cc: <bugzilla-daemon@bugzilla.kernel.org>
Cc: "Andrew Morton" <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We want this to happen after the PCI quirks, which are now running at
the very end of the fs_initcalls.
This works around the BIOS problems which were originally addressed by
commit db8be50c43 ('USB: Work around BIOS
bugs by quiescing USB controllers earlier'), which was reverted in
commit d93a8f829f.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Having this as a device_initcall() means that some real device drivers
can actually initialise _before_ the quirks are run, which is wrong.
We want it to run _before_ device_initcall(), but _after_ fs_initcall(),
since some arch-specific PCI initialisation like pcibios_assign_resources()
is done at fs_initcall().
We could use rootfs_initcall() but I actually want to use that for the
IOMMU initialisation, which has to come after the quirks, but still
before the real devices. So use fs_initcall_sync() instead -- since this
is entirely synchronous, it doesn't hurt that it'll escape the
synchronisation.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This function may have done more in the past, but all it does now is
apply the PCI_FIXUP_FINAL quirks. So name it sensibly and put it where
it belongs.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The usb regulator supplies (usb1v5, usb1v8 & usb3v1) must be available
before adding the twl4030_usb child, else twl4030_usb_ldo_init() will
always fail thus causing boot lock-up.
This patch fixes boot on OMAP systems using the twl4030 usb transceiver.
CONFIG_TWL4030_USB=y
Signed-off-by: Roger Quadros <ext-roger.quadros@nokia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Thanks to tip form ARM folks and Russell King.
If flush_dcache_page() occurs on a swapin it will have a mapping
and we'll try to defer the flush by setting the dirty bit.
But when it hits update_dcache_page() we won't flush because the
page won't have a mapping any more. So remove the mapping
requirement in flush_dcache().
Signed-off-by: David S. Miller <davem@davemloft.net>
If the loop in hidraw_read() loops more than once, then we might
end up trying to acquire already locked mutex, casuing a deadlock.
Reported-by: iceberg <iceberg@ispras.ru>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The following htmldocs warnings:
Warning(kernel/sched.c:685): No description found for parameter 'cpu'
Warning(kernel/sched.c:3676): No description found for parameter 'sd'
Trigger because new parameters were added to update_rq_clock() and
update_group_power() without updating the kernel-doc notation.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <4AD29070.7070002@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the following two compile warnings which show up on i386.
mm/percpu.c:1873: warning: comparison of distinct pointer types lacks a cast
mm/percpu.c:1879: warning: format '%lx' expects type 'long unsigned int', but argument 2 has type 'size_t'
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Randy Dunlap reported that 'make NO_64BIT=1' fails to build
a pure 32-b it binary on 64-bit/64-bit x86 systems.
The reason is that we dont pass in the -m32 and GCC defaults
to -m64.
So pass it in - and also extend the warning message about libelf
dependencies - glibc-dev[el] is needed as well beyond the libelf
library.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: Message-Id: <20091005131729.78444bfb.randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
PXA27x Errata #37 implies system will hang when switching into or out of
half turbo (HT bit in CLKCFG) mode, workaround this by not using it.
Signed-off-by: Dennis O'Brien <dennis.obrien@eqware.net>
Cc: stable-2.6.31 <stable@kernel.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Currently the irq_type field of the csb726_lan_config structure is
initialized twice. The value in the first case,
SMSC911X_IRQ_POLARITY_ACTIVE_LOW, is normally stored in the irq_polarity
field, so I have renamed the field in the first initialization to that.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The following perf build warnings/errors in function
argument types:
builtin-sched.c:1894: warning: passing argument 1 of 'sort_dimension__add' discards qualifiers from pointer target type
util/trace-event-parse.c:685: warning: passing argument 2 of 'read_expected' discards qualifiers from pointer target type
util/trace-event-parse.c:741: warning: passing argument 4 of 'test_type_token' discards qualifiers from pointer target type
util/trace-event-parse.c:706: warning: passing argument 2 of 'read_expected_item' discards qualifiers from pointer target type
... trigger because older GCC is not able to prove that
sort_dimension__add() does not change the string.
Some goes for test_type_token().
Fix this by improving type consistency.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Paul Mackerras <paulus@samba.org>
LKML-Reference: <20091005131729.78444bfb.randy.dunlap@oracle.com>
[ Also remove ugly type cast now unnecessary. ]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit db8be50c43, as per
http://bugzilla.kernel.org/show_bug.cgi?id=14374http://marc.info/?l=linux-kernel&m=125446885705223&w=4
We simply can't do the USB handoff at FIXUP_HEADER time, since it will
often require us to have valid IO mappings etc. But that in turn
requires a whole different approach, not this trivial one-liner.
Maybe we could teach all the USB quirk handoff handlers to only do the
quirk if the device has all its registers set up (since if it isn't
initialized, it's unlikely to be active), but regardless that will need
a whole lot more code than just saying "let's do it really early".
The proper fix is almost certainly to just leave the legacy IOMMU
mappings active until after all devices have been initialized.
Reported-by: Nick Piggin <npiggin@suse.de>
Cc: David Woodhouse <David.Woodhouse@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As reported in
http://bugzilla.kernel.org/show_bug.cgi?id=13940
on some system when acpi are enabled, acpi clears some BAR for some
devices without reason, and kernel will need to allocate devices for
them. It then apparently hits some undocumented resource conflict,
resulting in non-working devices.
Try to increase alignment to get more safe range for unassigned devices.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Revert commit 575543347b
It caused following issues:
- On architectures where ARCH= setting is used to select between
32 and 64 bit this was no longer possible without "make mrproper"
- If ARCH was changed then kbuild refused to run "make mrproper"
because ARCH had changed
- When CROSS_COMPILE was changed people were asked to run "make mrproper"
but kbuild refused to run "make mrproper" because CROSS_COMPILE changed.
- Spaces in CROSS_COMPILE was not 'supported'
- If an non-existing ARCH= was used kbuild could get stuck
Lessons learned:
. Despite being simple and straghtforward people uses very different
approaches when building the kernel.
. CROSS_COMPILE is sometimes used for ccache despite cache being
only a CC frontend so one would have expected CC to be
used for this purpose.
. And obviously this was not tested widely enough.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
User applications frequently hit problems when they try to use
the kernel headers directly, rather than the exported headers.
This adds an explicit warning for this case, and points to
a URL holding an explanation of why this is wrong and what
to do about it.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
UTS_TRUNCATTE is simpler this way, and now editors idetify this as a
shell script.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Otherwise we get:
"dnsdomainname: Unknown host"
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
The Makefile.lib will call "echo -ne" to append uncompressed kernel size to
bzip2/lzma kernel image.
The "echo" here depends on the shell that /bin/sh pointing to.
On Ubuntu system, the /bin/sh is pointing to dash, which does not support
"echo -e" at all. Use /bin/echo instead of shell echo should always be safe.
Signed-off-by: Alek Du <alek.du@intel.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Alek reported that on Ubuntu, where dash is used, 'echo -e'
can't work, so let's use non-builtin echo in this case.
Reported-by: Alek Du <alek.du@intel.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
