Now that it's June, it's about time to update
the copyright notices of files that have changed.
Signed-off-by: John Gregor <john.gregor@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This centralizes the use of the abort functionality, removes the
unneeded buffer cancel (abort does the same thing), sets up to ignore
launch errors after abort, same as cancel. We need abort on exit from
freeze mode to avoid having buffers stuck in the busy state, if a user
process happened to complete the send while we were in freeze mode
doing the recovery.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Define pkt rcvd 'type' in a way consistent with HW spec and chips.
The hardware considers received packets of type 0 to be expected, and
type 1 to be eager. The driver was calling the ipath_f_put_tid
functions using a variable called 'type' set to 0 for eager and to 1
for expected packets. Worse, the iba6110 and iba6120 drivers used
those values inconsistently. This was quite confusing. Now
everything is consistent with the hardware.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Recognize IBA 6110 Revision 4: same feature set, etc. as earlier revisions.
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We currently track various errors, now we enhance that capability by
logging some of them to EEPROM. We also now log a cumulative "active"
time defined by traffic though the InfiniPath HCA beyond the normal SM
traffic.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The new LED blinking interface adds more contention for the
unprotected GPIO pins that were already shared, though not commonly at
the same time. We add locks to the accesses to these pins so that
Read-Modify-Write is now safe. Some of these locks are added at
interrupt context, so we shadow the registers which drive and inspect
these pins to avoid the mmio read/writes. This mitigates the effects
of the locks and hastens us through the interrupt.
Add locking and always use shadows for registers controlling GPIO pins
(ExtCtrl and GPIOout). The use of shadows implies doing less I/O,
which can make I2C operation too fast on some platforms. An explicit
udelay(1) in SCL manipulation fixes that.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
When we want to find an InfiniPath HCA in a rack of nodes, it is often
expeditious to blink the status LEDs via a userspace /sys file.
A write-only led_override "file" is published per device. Writes to
this file are interpreted as (string form) numbers, and the resulting
value sent to ipath_set_led_override(). The upper eight bits are
interpretted as a 4.4 fixed-point "frequency in Hertz", and the bottom
two 4-bit values are alternately (D0..3, then D4..7) used by the
board-specific LED-setting function to override the normal state.
Signed-off-by: Michael Albaugh <michael.albaugh@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If the chip is no longer usable, LEDs should be turned off so system
can be found easily in the cluster.
Also some minor reorganizing so both chips print hardware error
message at same point and only if there were unrecovered errors
Signed-off-by: Dave Olson <dave.olson@qlogic.com>
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Correct mis-spellings of "algorithm", "appear", "consistent" and
(shame, shame) "kernel".
Signed-off-by: Robert P. J. Day <rpjday@mindspring.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Remove variables that are set but then never looked at in the ipath
driver. These cleanups came from David Binderman's list of "set but
never used" warnings from icc.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Eric's changes to the htirq infrastructure require corresponding
modifications to the ipath HT driver code so that interrupts are still
delivered properly.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Cc: Eric W. Biederman <ebiederm@xmission.com>
Cc: Roland Dreier <rdreier@cisco.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We can sometimes trigger parity errors due to processor speculative
reads to our write-combined memory (mostly seen on Woodcrest). Add a
stats counter for these.
Factored out the sendbuffererror buffer cancellation code so it can be
used in the new handling; suppress likely subsequent error messages if
within two jiffies of the cancellation.
Also restore 2 dropped TXE lines on hwe_bitsextant noticed while
debugging.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The system must be powercycled to clear a HT CRC error; reloading the
driver is not enough.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Prior to this change, the driver was not able to support a HT and PCIE
card simultaneously present in the same machine.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
0x08 is the HT capability, while PCI_CAP_ID_HT_IRQCONF would be
the subtype 0x80 that mpic_scan_ht_pic() uses.
Rename PCI_CAP_ID_HT_IRQCONF into PCI_CAP_ID_HT.
And by the way, use it in the ipath driver instead of defining its
own HT_CAPABILITY_ID.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Also added the word "Hardware" after "Fatal" to make it more obvious
that it's hardware, not software.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch only renames files, fixes product names, and updates
comments.
Signed-off-by: Bryan O'Sullivan <bryan.osullivan@qlogic.com>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
