Check for ACPI resource conflicts in hwmon drivers. I've included
all Super-I/O and PCI drivers.
I've voluntarily left out:
* Vendor-specific drivers: if they conflicted on any system, this would
pretty much mean that they conflict on all systems, and we would know
by now.
* Legacy ISA drivers (lm78 and w83781d): they only support chips found
on old designs were ACPI either wasn't supported or didn't deal with
thermal management.
* Drivers accessing the I/O resources indirectly (e.g. through SMBus):
the checks are already done where they belong, i.e. in the bus drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Acked-by: David Hubbard <david.c.hubbard@gmail.com>
Allow it87.c to handle IT8720 chipset like IT8718 in order to
retrieve voltage, temperatures and fans speed from sensors
tools. Also updating the related documentation.
Signed-off-by: Jean-Marc Spaggiari <jean-marc@spaggiari.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it87 driver doesn't follow the standard sensor type values as
documented in Documentation/hwmon/sysfs-interface. It uses value 2 for
thermistors instead of value 4. This causes "sensors" to tell the user
that the chip is setup for a transistor while it is actually setup for
a thermistor.
Using value 4 for thermistors solves the problem. For compatibility
reasons, we still accept value 2 but emit a warning message so that
users update their configuration files.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <hdegoede@redhat.com>
On the Shuttle SN68PT, FAN_CTL2 is apparently not connected to a fan,
but to something else. One user has reported instant system power-off
when changing the PWM2 duty cycle, so we disable it.
I use the board name string as the trigger in case the same board is
ever used in other systems.
This closes lm-sensors ticket #2349:
pwmconfig causes a hard poweroff
http://www.lm-sensors.org/ticket/2349
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The IT8712F v0.9.1 datasheet applies to revisions >= 0x8 (J).
The driver was incorrectly attempting to enable 16-bit fan
readings on rev 0x7 (I) which led to incorrect RPM values.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Tested-by: John Gumb <john.gumb@tandberg.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it8705 chip supports 16-bit fan tachometers in revisions at least
>= 0x03 (Version G). This patch enables 16-bit fan readings on all
revisions >= 0x03 just like the it8712, it8716, and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
The it8712 chip supports 16-bit fan tachometers in revisions >= 0x07.
Revisions >= 0x08 dropped support for 8-bit fan divisor registers. The
patch enables 16-bit fan readings on all revisions >= 0x07 just like
the it8716 and it8718 chips.
Signed-off-by: Andrew Paprocki <andrew@ishiboo.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
In commit f8d0c19a93 I forgot to delete
the pwmN_freq files on driver removal, here's the fix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Riku Voipio <riku.voipio@movial.fi>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
While it is possible to force SMBus-based hardware monitoring chip
drivers to drive a not officially supported device, we do not have this
possibility for Super-I/O-based drivers. That's unfortunate because
sometimes newer chips are fully compatible and just forcing the driver
to load would work. Instead of that we have to tell the users to
recompile the kernel driver, which isn't an easy task for everyone.
So, I propose that we add a module parameter to all Super-I/O based
hardware monitoring drivers, letting advanced users force the driver
to load on their machine. The user has to provide the device ID of a
supposedly compatible device. This requires looking at the source code or
a datasheet, so I am confident that users can't randomly force a driver
without knowing what they are doing. Thus this should be relatively safe.
As you can see from the code, the implementation is pretty simple and
unintrusive.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The IT8705F and related parts are Super I/O controllers that contain
many separate devices.
Some BIOSes describe IT8705F I/O port usage under a motherboard device
(PNP0C02) with overlapping regions, e.g., 0x290-0x29f and 0x290-0x294.
The it87 driver supports only the Environment Controller, which requires
only two ISA ports, but it used to request an eight-port range. If that
range exceeds a range reported by the BIOS, as 0x290-0x297 would, the
request fails, and the it87 driver cannot claim the device.
This patch makes the it87 driver request only the two ports used for the
Environment Controller device.
Systems where this problem has been reported:
Gigabyte GA-K8N Ultra 9
Gigabyte M56S-S3
Gigabyte GA-965G-DS3
Kernel bug reports:
http://bugzilla.kernel.org/show_bug.cgi?id=9514http://lkml.org/lkml/2007/12/4/466
Related change:
http://git.kernel.org/?p=linux/kernel/git/torvalds/linux-2.6.git;a=commitdiff;h=a7839e960675b549f06209d18283d5cee2ce9261
The patch above increases the number of PNP port resources we support.
Prior to this patch, we ignored some port resources, which masked the
it87 problem.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
The VRM value is not read from chip registers, so there's no need
to update the device data cache before exporting the VRM value to
user-space.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Hans de Goede <j.w.r.degoede@hhs.nl>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for the IT8716F and IT8718F fan4 and fan5. The late
revisions of the IT8712F have these too but support is harder to add
and nobody asked for it yet, so I didn't include it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Convert from class_device to device for hwmon_device_register/unregister
Signed-off-by: Tony Jones <tonyj@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
On Sun, 22 Jul 2007 00:30:56 +0200, Gabriel C wrote:
> I noticed this warnings on current git:
>
> drivers/hwmon/pc87360.c:1082: warning: 'pc87360_remove' defined but not used
> drivers/hwmon/sis5595.c:580: warning: 'sis5595_remove' defined but not used
> drivers/hwmon/smsc47m1.c:608: warning: 'smsc47m1_remove' defined but not used
> drivers/hwmon/via686a.c:648: warning: 'via686a_remove' defined but not used
> drivers/hwmon/vt8231.c:755: warning: 'vt8231_remove' defined but not used
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
This is the patch for converting it87 to a platform driver (and remove i2c-isa).
Signed-off-by: Corentin LABBE <corentin.labbe@geomatys.fr>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mark M. Hoffman <mhoffman@lightlink.com>
Add support for IT8726F chip driver, which is just same as
IT8716F with additional glue logic for AMD power sequencing.
Signed-off-by: Rudolf Marek <r.marek@assembler.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Many hardware monitoring drivers use two different mutexes, one to
protect their per-device data structure, and one to protect the
access to the device registers. These mutexes are essentially
redundant, as the drivers are transfering values between the device
registers and the data cache, so they almost always end up holding
both mutexes at the same time. Using a single mutex will make the
code more simple and faster.
I am changing only two of the affected drivers here, the authors
of the other affected drivers are welcome to submit similar patches
if they want.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Let the user select the base PWM frequency when using the it87
hardware monitoring driver. Different frequencies can give better
control on some fans.
Also update the documentation to mention the PWM frequency control
files, with misc cleanups to the PWM section.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
This interface was useless as the LPC ISA-like interface is always
available, is faster, and is more reliable. This cuts the driver
size by some 20%.
This change is also required to later convert the it87 driver to a
platform driver, so that we can get rid of i2c-isa in a near future.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
hwmon: Fix unchecked return status, batch 5
Fix up some hwmon drivers so that they no longer ignore return status
from device_create_file().
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Copyright update
I think my contributions to the it87 driver over the past two
years qualify me as a co-author of this driver.
Also drop old comments of dubious usefulness.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Overwrite broken default limits
Some IT8716F chips where seen with unreasonable defaults for low
voltage and high temperature limits. Overwrite them with sane defaults
so as to not generate meaningless alarms.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Add support for the IT8718F
The IT8718F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8716F, so adding support to the
it87 driver was pretty straightforward. The most significant difference
is that the IT8718F has up to 8 VID pins, instead of 6 for the older
chips.
For the IT8718F, the VID value can only be read from Super-I/O space.
Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Cleanup set_fan_div
We only change one fan clock divider at a time, so there is only one
fan min which needs to be saved and restored.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Prevent overflow on fan clock divider write
The highest possible clock divider for fan1 and fan2 is 128.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: No sysfs files for disabled fans
Only create the fan attributes for enabled fan tachometers. Some
motherboards have a nice BIOS which only enables the fan inputs which
are wired to a fan header on the board. This makes the configuration
easier for the user.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
it87: Add support for the IT8716F
The IT8716F is a Super-I/O chip with integrated hardware monitoring
functions. It is very similar to the IT8712F, so adding support to the
it87 driver was pretty straightforward. The most significant change here
is that the IT8716F has 16-bit fan speed counters, so the user no more
needs to tweak the fan clock dividers to get the best readings.
Userspace support is already in lm_sensors SVN (to be soon released
as 2.10.1.)
Thanks to Stian Oksavik, Olivier Nicolas, Prakash Punnoor and
Juergen Kilb for testing the early versions of this patch.
Thanks also to ITE for providing datasheets and answering my questions.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c-isa: Restore driver owner
Commit 2b48716d1d back in January
2006 was a bit overzealous. It removed .owner from all i2c drivers,
including i2c-isa ones, while they still need it.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
"register" is a reserved keyword so using it as a parameter name
can confuse some compilers, most notably ICC.
The patch below just renames all occurences to reg which fits the actual
function declarations.
Signed-off-by: Darren Jenkins <darrenrjenkins@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
convert drivers/hwmon/*.c semaphore use to mutexes.
the conversion was generated via scripts, and the result was validated
automatically via a script as well.
all affected hwmon drivers were build-tested.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix an oops on it87 module removal when no supported hardware was
found.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Only scan I2C address 0x2d. This is the default address and no IT87xxF
chip was ever seen on I2C at a different address. These chips are
better accessed through their ISA interface anyway.
This fixes bug #5889, although it doesn't address the whole class
of problems. We'd need the ability to blacklist arbitrary I2C addresses
on systems known to contain I2C devices which behave badly when probed.
Plan the I2C interface for removal as well. If nobody complains within
a year, it will confirm my impression that the I2C interface isn't
actually needed by anyone.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the hwmon drivers.
Signed-off-by: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix a bug where setting the low fan speed limits will not work if no
data was ever read through the sysfs interface and the fan clock
dividers have not been explicitely set yet either. The reason is that
data->fan_div[nr] may currently be used before it is initialized from
the chip register values. The fix is to explicitely initialize
data->fan_div[nr] before using it.
Bug reported, and fix tested, by Nicolas Mailhot.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixup functions that have been declared static
and then actually defined without the static on.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Use kzalloc instead of kmalloc+memset in all hardware monitoring
drivers.
Signed-off-by: Deepak Saxena <dsaxena@plexity.net>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drop legacy ISA address support from the it87 driver. All supported
chips are Super-I/O chips, so the device ISA address can be safely read
from Super-I/O space rather than blindly assumed.
Two nearby inaccurate documentation statements have been fixed as well:
* The IT8705F doesn't have an SMBus interface.
* The SiS950 doesn't have a distinct prefix.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only part left in i2c-sensor is the VRM/VRD/VID handling code.
This is in no way related to i2c, so it doesn't belong there. Move
the code to hwmon, where it belongs.
Note that not all hardware monitoring drivers do VRM/VRD/VID
operations, so less drivers depend on hwmon-vid than there were
depending on i2c-sensor.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The only thing left in i2c-sensor.h are module parameter definition
macros. It's only an extension of what i2c.h offers, and this extension
is not sensors-specific. As a matter of fact, a few non-sensors drivers
use them. So we better merge them in i2c.h, and get rid of i2c-sensor.h
altogether.
Signed-off-by: Jean Delvare <khali@linux-fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
i2c_probe and i2c_detect now do the exact same thing and operate on
the same data structure, so we can have everyone call i2c_probe.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Super-I/O find functions in hardware monitoring drivers can be tagged
__init as they are only called from functions themselves tagged __init.
Two of them (smsc47b397 and w83627ehf) already do, but the other four
of them (it87, pc87360, smsc47m1 and w83627hf) did not.
This saves a few bytes of memory after the drivers are loaded, 192 in
the case of the it87 driver.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
We could refactor the error message 34 different i2c drivers print if
i2c_detach_client() fails in this function itself. Saves quite a few
lines of code. Documentation is updated to reflect that change.
Note that this patch should be applied after Rudolf Marek's w83792d
patches.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
