Bringup 3 ports GC(5G)+SAP(2.4G ACS mode)+SAP(2.4G ACS mode) in
sequence, the second SAP can't get pcl channel, it's wrong.
Fix is to add GC+SAP+SAP configuration items definition to
pm_third_connection_pcl_dbs_2x2_table and
pm_next_action_three_connection_dbs_2x2_table.
Change-Id: I943ed7cdff0bd0920953b60fcb2cfa1f5bf79dc2
CRs-Fixed: 2627832
The Qtime offset derived with a connected AP (master) are not
cleared on disconnect. This leads to storage of stale offset
values. So clear the stale Qtime offset values on disconnection.
Currently there is no information in ftm_time_sync sysfs entry
regarding which BSSID the Qtime offset values are derived.
Add the BSSID info in the sysfs entry.
Change-Id: Iac47bccffae005602469a658e5ca0bc9008ac4b4
CRs-Fixed: 2629822
Add ini support for DFS Channel Ageout Time, the time upto which
DFS channel information such as beacon found is remembered.
This ini is used to set the ageout timer value from host to FW.
If not set, FW will disable ageout time.
This value is sent as a WMI_PDEV_PARAM_SET_DFS_CHAN_AGEOUT_TIME
as part of WMI_PDEV_SET_PARAM_CMDID.
Change-Id: I99553fa87a4025f03c52b4b387a414ba06c2c457
CRs-Fixed: 2625996
Glitches seen after the STA disconnection because of the roam scan
triggered on a heartbeat failure ( beacon miss ).STA does a partial
scan followed by full scan causing the DUT to go off-channel from
the STA and P2P home channel, causing the music BLIP.
Fix is to disable roaming irrespective of data traffic present
or not on P2P interface and enabled again once P2P is disconnected.
Change-Id: I5ddf946adbfbe99d5b20c23c46b2b4ac0bfac47f
CRs-Fixed: 2632939
Currently in net dev cleanup of ipa host interface if the
ipa interface does not exist for that particular net dev,
last ipa iface reference is passed. This may lead to invalid
access. So fix by validating the iface context before clean
up of host ipa interface.
Change-Id: I753c922b5c82c676a318df87552051fdd74c983c
CRs-Fixed: 2632382
There are various entry and exit prints present in DSC that are not
necessary for any debugging purpose.
Cleanup these extra logs
Change-Id: I0f2f5b03ddc3e4535cc352fd13782eac1a235121
CRs-Fixed: 2616198
ignore_fw_reg_offload_ind is used to ignore regdb offload
indication from FW and regulatory is treated as non offload.
Change-Id: Ic9a47fe3ec49cf1fa9cbf7ab166decdc4ece0511
CRs-Fixed: 2630994
Introduce ini for roaming_triggers to enable/disable specific
roaming triggers. This will be the master ini to control roaming
triggers. If this ini is set to zero, roaming will not be enabled
on the sta interface unless its enabled via vendor command.
A new roaming trigger - Sta kickout roaming is introduced in
firmware, include this bit support also in the ini.
The value of this ini will be sent over the wmi command
WMI_ROAM_ENABLE_DISABLE_TRIGGER_REASON_CMDID during RSO start.
Reset this value to 0 during RSO stop if RSO stop is due to
disconnect or roam synch failure.
Change-Id: I02f207cdde9d8fb68cd91fab07572baa9e7ac50d
CRs-Fixed: 2631712
Introduce an INI "enable_roam_reason_vsie" to inidicate fw to
include/exculde roam reason vsie in reassoc frame
Change-Id: I4d2a44812d8b11a19b0d7d31eb31c826aaeda79d
CRs-Fixed: 2627472
Currently, if roaming happens roam reason is not sent to AP. AP will
not able to know why roaming happened. As roaming is offloaded to
firmware, firmware will include roam reason vsie based on driver
indication by vdev param
WMI_VDEV_PARAM_ENABLE_DISABLE_ROAM_REASON_VSIE based on
below conditions:
Parse the QCA attribute CONFIG_ROAM_REASON to control
inclusion/exculsion of roam reason vsie dynamically. Vendor subcommand
QCA_NL80211_VENDOR_SUBCMD_SET_WIFI_CONFIGURATION can control roam
reason vsie inclusion using QCA atrribute CONFIG_ROAM_REASON.
Different operations required to implement this feature can be
specified in QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON, so driver parses
CONFIG_ROAM_REASON, updates enable_roam_reason_vsie and indicates to
firmware by updating vdev param.
a.) If Userspace wants the firmware to include roam reason in reassoc
frame, it can send QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON with
value 1 and driver will update enable_roam_reason_vsie to 1.
Driver will update vdev parameter
WMI_VDEV_PARAM_ENABLE_DISABLE_ROAM_REASON_VSIE, so that firmware
can include roam reason vsie in reassoc frame during roaming.
b.) If this command is not issued, the default behavior of the
firmware is not to include err reason code in beacon report
response. Driver will send default value of
enable_roam_reason_vsie to firmware which is 0.
c.) The userspace requests the firmware to stop roam reason vsie
reporting when roam reason is not required for AP anymore. If
userspace doesn't want the roam reason inclusion, userspace can
send QCA_WLAN_VENDOR_ATTR_CONFIG_ROAM_REASON with value 0 and
driver will update enable_roam_reason_vsie and notify firmware to
exclude roam reason.
If userspace requests the driver to get the status of
enable_roam_reason_vsie , to check whether firmware includes roam
reason vsie or not, driver will fill CONFIG_ROAM_REASON attribute and
will update to userspace.
Change-Id: I063c822e99fd6908bd4188b429ffa6a2031cee5d
CRs-Fixed: 2624713
When dynamic channel switch is enabled, trigger acs and switch to best
channel if wlan interference is found in 5g mac.
Change-Id: I56661f5c42a233a0dc0a6400d75cb8f5c0019706
CRs-Fixed: 2599176
ARP/NS offload cannot be executed in NaN mode, but currently there is no
check on vdev for opmode so it is still trying to execute. Add an if
check for opmode of vdev and return QDF_STATUS_E_INVAL if in NaN mode.
Change-Id: I89accfef625c2a1eae944662acdff5d3fdd6ea9d
CRs-Fixed: 2630329
Extend radiotap header to append ACK status and tx retry count
for packets sent to virtual mon interface.
Change-Id: If110a7de736c3efc0d477617089669104c6f1690
CRs-Fixed: 2627707
For the MON Interface, sometimes Mgmt Tx Pkts are captured after Rx
Pkts get captured in tcpdump. This is happening because Tx Pkts are
sent to mon after waiting for Tx completion.
Now Mgmt Tx frames are sent twice to MON interface, one without
waiting for Tx completion with magic number as status field, so
that the Tx Pkts get captured in tcpdump before Rx Pkts and normal
Tx Pkts get captured, which is after Tx completion will remain same.
Change-Id: Idfc65087bd62cd8ef64306501b600caec424ba02
CRs-Fixed: 2627716
For packet capture mode, record the channel number on
which STA vdev is operating on.
Change-Id: Id52536b5b238dc1e4fe4c612a651c6fe8ddc17d3
CRs-Fixed: 2627713
Currently the driver waits for cancel roc request in the
API p2p_cleanup_param which gets executed in the scheduler context.
Scan cancel requests also executes in the scheduler context, so
the wait would fail as the scheduler thread is waiting for
the message to get processed which it would only process, which
would in turn cause a latency in P2P connection.
Fix is to remove the wait which is mentioned above.
Change-Id: I12a1a7e4896ecf3a9c6e8f138e18637690cbd049
CRs-Fixed: 2622051
Add the sysfs entry ftm_time_sync in STA mode to show the offset
derived for the STA(slave) with respect to connected AP(master).
Change-Id: I05b16ccdb983c53fb86eeb14ba98bd3cc9a2dce6
CRs-Fixed: 2621152
Improve logging in driver by avoiding unnecessary error prints
and combining logs.
Change-Id: Ibab9067aa1bce992f36fca22a5aed88e8d85ba25
CRs-Fixed: 2627549
Clear sae_single_pmk info while processing del/flush pmk command
from supplicant, if required.
Change-Id: Idd974822ef0426461cd9971e54d8244d64b246b5
CRs-Fixed: 2616036
Requirement is to allow station to just keeps only one
PMK1 and PMKID1 which gets derived while first connection
and re-use it for roaming to other AP which has some
specific VSIE.
To support this feature, STA should Set new flag in 11i
params during RSO start/update when initial connection is
completed based on the VSIE in AP beacon/probe response
frame. This flag will allow fw to roam to AP(s) which has
VSIE with single PMK.
Update PMK info in RSO start command with
sae_single_pmk info if initial connection is completed
with AP contains VSIE.
Change-Id: I839b48da48f92f24444e69405d87560186d7f986
CRs-Fixed: 2616029
Requirement is to allow station to just keeps only one
PMK1 and PMKID1 which gets derived while first connection
and re-use it for roaming to other AP which has some
specific VSIE.
To support this feature, STA should:
1. Set new flag in 11i params during RSO start/update when
initial connection is completed based on the VSIE in AP
beacon/probe response frame. This flag will allow fw to roam
to AP(s) which has VSIE with single PMK.
2. STA should dynamically enable this feature if below
vendor specific IE on AP’s Beacon or Probe Response at
the first connection:
Category Data
Type 0xDD
Length 0x05
OUI 0x00 40 96
Type 0x03
Data Don’t care
(EX, 0x05)
Maintain a separate pmk information structure to support sae
roaming using single pmk.
Change-Id: I0aac7659cecd4d8aaff86c9715e512cf46f22615
CRs-Fixed: 2616035
AP isolation a.k.a intra-bss forwarding is a per AP attribute. Issue in
current IPA implementation is that it does not support per AP control.
In a SAP-SAP configuration, latter SAP configuration will always overwrite
first SAP's isolation configuration.
Fix is to add vdev id parameter from protocol layer so that IPA component
could configure AP isolation on a per AP basis.
Change-Id: I9c96cdcda03eb10b4c2984a757e52d77b5bf6790
CRs-Fixed: 2624757
Currently the TDLS module prints the peer info
every defined time interval which leads to too
much of information even when no rx tx is
ongoing with the peer which leads to excessive
logging.
Fix is to limit the logs and print only when there
is activity going on.
Change-Id: I6c1bf5a1ce8a858dfe895168178154a6c8b49c1f
CRs-Fixed: 2625632
Optimize logs after connect complete i.e roam offload params
and tdls state etc.
Change-Id: I5df7eb236ef1c7369f4d996c4f0eda7225652f12
CRs-Fixed: 2627694
Userspace expects the assoc request IEs of a disconnected station
to derive 11kv capabilities. Send the same in STA_INFO as part
of remote station info.
Change-Id: Iab5f39de833cd06e814e83f0149a0d21caf59b9f
CRs-Fixed: 2624922
Introduce a compile time flag SAE_SINGLE_PMK and new INI
"sae_same_pmk_feature_enabled" to enable/disable SAE
Roaming with same PMK/PMKID feature.
Change-Id: Ifca8ec8bcf6e9a2f1d8409b35390bfee0033bd30
CRs-Fixed: 2616025
FTM time sync feature is triggered when connection takes place
in case of STA and bss starts in case of SAP. The feature is
stopped when STA disconnects and bss stops.
Change-Id: I963b0134b7432c9827c2fb3d9dce7c81a8666d4d
CRs-Fixed: 2621144
Add ini config required for FTM time sync feature.
"enable_time_sync_ftm"- ini to enable/disable the feature.
"time_sync_ftm_mode" - ini to configure the burst/aggregated mode.
In burst mode the offset derived for each RTT frame is sent by
firmware, in aggregated mode only one offset is sent by firmware.
"time_sync_ftm_role" - ini to configure slave(STA)/master(SAP) role.
Change-Id: I6a06d6fdc4c7556c32ab2d28f1cbaa936b98a85b
CRs-Fixed: 2618654
Register tx and rx ops to send packet capture mode command and
to receive mgmt offload handler for packet capture component.
Change-Id: I70da00feff29399b98c5916eec17e26b62285db3
CRs-Fixed: 2619321
If resume and fw wakeup happens at the same time.
psoc_ctx->lock maybe doing bottom half operation for resume,
then wakeup interrupt comes on same cpu, the interrupt
handler will also acquire psoc_ctx->lock in
pmo_core_update_wow_initial_wake_up, which cause dead lock.
Using atomic for wow_initial_wake_up, so the interrupt handler
can avoid using spin_lock.
Change-Id: Id0e963a0924415e9660c57a1c1b776d3e609213d
CRs-Fixed: 2624899
Add support for the following NAN messages in kmsg:-
1. NAN enable status
2. NAN, NDP match events
3. NDP channel info.
etc.
Change-Id: Icbf8f4ed05a7bd181a076d526dd2e01d70be6b05
CRs-Fixed: 2618835
Enhance logs in policy mgr module to remove duplicate
or unwanted prints and keep only useful logs to debug.
Change-Id: Ifd585256955aceec29286d82838be0c588228c32
CRs-Fixed: 2614763
Process management Tx and Rx frames for packet capture mode
and post frames to the mon thread.
Change-Id: I14c0a1cf8a8aa4d4a4e16ad6200715b875611c81
CRs-Fixed: 2619317
Send vdev param command to FW for STA vdev to set the packet
capture mode. Send the command only if packet capture support
is enabled.
Change-Id: Ifed2431882b1f7d2869771e812daa5bcd5dc17e9
CRs-Fixed: 2619314
During CU and low rssi based roam triggers, consider AP as roam candidate
only if its roam score is better than connected AP score by at least
min_roam_score_delta.
User configures this candidate minimum roam score delta value using
"min_roam_score_delta" INI. User can set candidate minimum score delta
value between 0 to 10000 and default value is 1850.
Firmware will trigger roaming only if roam score of candidate AP is
greater than "min_roam_score_delta" & "roam_score_delta" values of
connected AP.
Change-Id: I180e769b5629aa405dbd89ed73e39e228adf92db
CRS-Fixed: 2614117
Add the function to parse the FTM timesync start/stop and offset
events received from target and populate them in ftm timsync
priv vdev structure.
Change-Id: Ibdcf97bb0a04fc6490c6bd2c26701036df92c5d4
CRs-Fixed: 2618646
