* 'upstream-linus' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/netdev-2.6: (116 commits)
sk98lin: planned removal
AT91: MACB support
sky2: version 1.12
sky2: add new chip ids
sky2: Yukon Extreme support
sky2: safer transmit timeout
sky2: TSO support for EC_U
sky2: use dev_err for error reports
sky2: add Wake On Lan support
fix unaligned exception in /drivers/net/wireless/orinoco.c
Remove unused kernel config option DLCI_COUNT
z85230: spinlock logic
mips: declance: Driver model for the PMAD-A
Spidernet: Rework RX linked list
NET: turn local_save_flags() + local_irq_disable() into local_irq_save()
NET-3c59x: turn local_save_flags() + local_irq_disable() into local_irq_save()
hp100: convert pci_module_init() to pci_register_driver()
NetXen: Added ethtool support for user level tools.
NetXen: Firmware crb init changes.
maintainers: add atl1 maintainers
...
This is the driver for the Toshiba TC86C001 GOKU-S PCI IDE controller,
completely reworked from the original brain-damaged Toshiba's 2.4 version.
This single channel UltraDMA/66 controller is very simple in programming,
yet Toshiba managed to plant many interesting bugs in it. The particularly
nasty "limitation 5" (as they call the errata) caused me to abuse the IDE
core in a possibly most interesting way so far. However, this is still
better than the #ifdef mess in drivers/ide/ide-io.c that the original
version included (well, it had much more mess)...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Driver for the PA Semi PWRficient on-chip Ethernet (1/10G)
Basic enablement, will be complemented with performance enhancements
over time. PHY support will be added as well.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch also adds symbolic defines for supported pci ids.
Signed-off-by: Alex Dubov <oakad@yahoo.com>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Support for these devices was broken for 2.6.18-rc1 and later by commit
146ad66eac, which added voltage level support.
This restores the previous behaviour for these devices by ensuring that when
the voltage is changed, only one write to set the voltage is performed.
It may be that both writes are needed if the voltage is being changed between
two non-zero values or that it's safe to ensure that only one write is done
if the hardware only supports one voltage; I don't know whether either is the
case nor can I test since I have only the one SD reader (1524:0550), and it
supports just the one voltage.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] Add new IDs to VIA AGP.
[AGPGART] Remove pointless assignment.
[AGPGART] Remove pointless typedef in ati-agp
[AGPGART] Prevent (unlikely) memory leak in amd_create_gatt_pages()
[AGPGART] intel_agp: restore graphics device's pci space early in resume
Culled from the VIA codedrop.
Also fixes up one ID used in amd64-agp to use the
VIA part number instead of the board name in its ID.
Signed-off-by: Dave Jones <davej@redhat.com>
This patch:
* Corrects the wrong device ID of PCI_DEVICE_ID_VIA_SATA_EIDE
from 0x0581 to 0x5324.
* Adds VIA CX700 and VT8237S support in drivers/ide/pci/via82cxxx.c
* Adds VIA VT8237S support in drivers/ata/pata_via.c
Signed-off-by: Josepch Chan <josephchan@via.com.tw>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] drivers/char/agp/sgi-agp.c: check kmalloc() return value
[AGPGART] Fix PCI-posting flush typo.
[AGPGART] fix detection of aperture size versus GTT size on G965
[AGPGART] Remove unnecessary flushes when inserting and removing pages.
[AGPGART] K8M890 support for amd-k8.
pci: add class codes for Wireless RF controllers
Add PCI codes to include/linux/pci_ids.h for RF controllers; first
batch of these devices seem to be the Ultra-Wide-Band and Wireless USB
controllers (WHCI spec).
Signed-off-by: Inaky Perez-Gonzalez <inaky@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change cloned experimental driver according to original 1.9.1 moxa driver.
Some int->ulong conversions, outb ~UART_IER_THRI constant. Remove commented
stuff.
I also added printk line with info, if somebody wants to test it, he may
contact me as I can potentially debug the driver with him or just to confirm
it works properly.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rename a poorly worded PCI ID for the Geode GX and CS5535 companion chips.
The graphics processor and host bridge actually live in the northbridge on
the integrated processor, not in the companion chip.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the parallel port (implemented as separate PCI function) on
the Oxford Semiconductor OX16PCI952.
Signed-off-by: Ryan Underwood <nemesis@icequake.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add Tg3_FLG2_IS_NIC flag to unambiguously determine whether the
device is NIC or onboard. Previously, the EEPROM_WRITE_PROT flag was
overloaded to also mean onboard. With the separation, we can
support some devices that are onboard but do not use eeprom write
protect.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add PCI ID and detection for 5709 copper and SerDes chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add pci device ids for the NVIDIA MCP67 chip.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This updated patch adds the Intel ICH9 LPC and SMBus Controller DID's.
Signed-off-by: Jason Gaston <jason.d.gaston@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
As per feature-removal-schedule.txt.
Signed-off-by: Yoichi Yuasa <yoichi_yuasa@tripeaks.co.jp>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
It was obesrved that at least one older PCI card predating the
requirement for the TRDY signal to respond within 16 clock ticks actually
does not meet this rule nor even the power-on defaults of the PCI bridges
found in development systems built around the Broadcom SiByte SOCs. Here
is a patch that bumps up the timeout to the highest finite value supported
by these chips, which is 255 clock ticks. The bridges affected are the
SiByte SOC itself and the SP1011.
This change does not effectively affect systems only having PCI option
cards installed that meet the TRDY requirement of the current PCI spec.
The rule was introduced with PCI 2.1, so any older card may make the
system affected. If this is the case, performance of the system will
suffer in return for the card working at all. If this is a concern, then
the solution is not to use such cards.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
---
MSI is defined to be 32-bit write. The 5706 does 64-bit MSI writes
with byte enables disabled on the unused 32-bit word. This is legal
but causes problems on the AMD 8132 which will eventually stop
responding after a while.
Without this patch, the MSI test done by the driver during open will
pass, but MSI will eventually stop working after a few MSIs are
written by the device.
AMD believes this incompatibility is unique to the 5706, and
prefers to locally disable MSI rather than globally disabling it
using pci_msi_quirk.
Update version to 1.4.45.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the new 5709 device. This is a new 10/100 Mbps chip.
The mailbox access and firmware interface are quite different from
all other tg3 chips.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add support for the temperature sensor(s) found in AMD K8 CPUs.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce msi_ht_cap_enabled() to check the MSI capability in the
Hypertransport configuration space.
It is used in a generic quirk quirk_msi_ht_cap() to check whether
MSI is enabled on hypertransport chipset, and a nVidia specific quirk
quirk_nvidia_ck804_msi_ht_cap() where two 2 HT MSI mappings have to
be checked.
Both quirks set the PCI_BUS_FLAGS_NO_MSI bus flag when MSI is disabled.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
New SiS south bridge device ID is 0x966.
Next coming product will be 0x968. (Will be released in Q4, this year)
We don't make any updates to the IDE controller.
Signed-off-by: David Wang <touch@sis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch to add VIA PCI quirk for Enhanced/Extended USB on VT8235
southbridge. It is needed in order to use EHCI/USB 2.0 with ACPI.
Without it IRQs are not routed correctly, you get an "Unlink after
no-IRQ?" error and the device is unusable.
I belive this could also be a fix for Bugzilla Bug 5835.
Signed-off-by: Mark Hindley <mark@hindley.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Here is a patch that adds support for the Instashield IS-200 2 port PCI
serial card.
Signed-off-by: Peter Horton <pdh@colonel-panic.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Unhide the SMBus controller on the Asus PU-DLS board.
This fixes bug #6763.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
arcmsr is a driver for the Areca Raid controller, a host based RAID
subsystem that speaks SCSI at the firmware level.
This patch is quite a clean up over the initial submission with
contributions from:
Randy Dunlap <rdunlap@xenotime.net>
Christoph Hellwig <hch@lst.de>
Matthew Wilcox <matthew@wil.cx>
Adrian Bunk <bunk@stusta.de>
Signed-off-by: Erich Chen <erich@areca.com.tw>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Add ids for SDHCI controllers so that they can be identified for quirks.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The patch below adds support for the TI PCIxx12 CardBus controllers.
This seems to be sufficient to detect the cardbus bridge on an HP nc6320
and works with an orinoco wifi card.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Partially revert 74d0a988d3:
[PATCH] PCI: Move various PCI IDs to header file
libata policy is to avoid use of named PCI device ID constants.
These are often single-use constants, which have little value over
direct numeric constants save for constant include/linux/pci_ids.h
patching/merging headaches.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the new nForce4 MCP51 (also known as nForce 410 or
430) and nForce4 MCP55 to the i2c-nforce2 driver. Some code changes
were required because the base I/O address registers have changed in
these versions. Standard BARs are now being used, while the original
nForce2 chips used non-standard ones.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch adds the ATI IXP southbridges support to i2c-piix4,
as it turned out those chips are compatible with it.
Signed-off-by: Rudolf Marek <r.marek@sh.cvut.cz>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The nVidia CK804 PCI-E chipset supports the AER extended capability
but sometimes fails to link it (with some BIOS or after a warm reboot).
It makes the AER cap invisible to pci_find_ext_capability().
The patch adds a quirk to set the missing bit that controls the
linking of the capability.
By the way, it removes the corresponding code in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Loic Prylli <loic@myri.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
