Expand comment explaining MAC address selection for replicated IGMP
frames transmitted in bonding mode 1 (active-backup). Also, a small
whitespace cleanup.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Add "HasHltClk" flag for RTL-8100B/8139D hardware in order to fix
problems resuming from suspend-to-RAM.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
work_done is overwritten each time through the rx_action loop in
epic_poll. This screws-up the NAPI accounting if the loop is executed
more than once.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Get rid of the mdelay call in rhine_disable_linkmon. The function
is called from the via-rhine versions of mdio_read and mdio_write.
Those functions are indirectly called from rhine_check_media and
rhine_tx_timeout, both of which can be called in interrupt context.
So, create tx_timeout_task and check_media_task as instances of struct
work_struct inside of rhine_private. Then, change rhine_tx_timeout to
invoke schedule_work for tx_timeout_task (i.e. rhine_tx_timeout_task),
moving the work to process context. Also, change rhine_error (invoked
from rhine_interrupt) to invoke schedule_work for check_media_task
(i.e. rhine_check_media_task), which simply calls rhine_check media
in process context. Finally, add a call to flush_scheduled_work in
rhine_close to avoid any resource conflicts with pending work items.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/net/e1000/e1000_main.c: In function `e1000_intr':
drivers/net/e1000/e1000_main.c:3156: error: `i' undeclared (first use in this function)
drivers/net/e1000/e1000_main.c:3156: error: (Each undeclared identifier is reported only once
drivers/net/e1000/e1000_main.c:3156: error: for each function it appears in.)
This function is foul.
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
These should really be addresses obtained with ioremap() or some
bus-specific backend, but for now...
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/declance.c | 4 ++--
1 files changed, 2 insertions(+), 2 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
o Add support for DP83847 MII.
o remove unused variable.
o Add some initialisations so even an unknown MII won't result in a crash.
o Correct error message to "no known MIIs found".
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/au1000_eth.c | 13 +++++--------
1 files changed, 5 insertions(+), 8 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
problem:
id[53-58] might be changed after initializing device CHS settings.
changes:
- call ata_dev_reread_id() to reread the identify device info,
after initializing device CHS settings.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
move the initialization of taskfile LBA flags
"ATA_TFLAG_LBA" and "ATA_TFLAG_LBA48 flags"
to the SCSI translation functions
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
If .owner isn't set the module can be unloaded even while still active.
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
SMACK (Stuttgart Modified Amateurradio CRC KISS) is a KISS variant that
uses CRC16 checksums to secure data transfers between the modem and host.
It's also used to communicate over a pty to applications such as Wampes.
Patches for Linux 2.4 by Thomas Osterried DL9SAU, upgraded to the latest
mkiss 2.6 mkiss driver by me.
Signed-off-by: Thomas Osterried DL9SAU <thomas@x-berg.in-berlin.de>
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From Suzanne Wood <suzannew@cs.pdx.edu>:
Clarify RCU implementation in bpqether.c.
Because bpq_new_device() calls list_add_rcu() and bpq_free_device() calls
list_del_rcu(), substitute list_for_each_entry_rcu() for
list_for_each_entry() in bpq_get_ax25_dev() and in bpq_seq_start().
Add rcu dereference protection in bpq_seq_next().
The rcu_read_lock()/unlock() in bpq_device_event() are removed because
netdev event handlers are called with RTNL locking in place.
FYI: bpq_free_device() calls list_del_rcu() which, per list.h, requires
synchronize_rcu() which can block or call_rcu() or call_rcu_bh() which
cannot block. Herbert Xu notes that synchronization is done here by
unregister_netdevice(). This calls synchronize_net() which in turn uses
synchronize_rcu().
Signed-off-by: Ralf Baechle DL5RB <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch fixes the following bugs with offline diagnostics
code(run with "ethtool -t").
1. After running offline diagnostics, adapter would report
corrupted packets on receive. This was because of adapter not
being brought out of "RLDRAM test mode".
2. Current EEPROM test works only for Xframe I. Since Xframe II
uses different interface(SPI), support for this interface has
been added. Also, since SPI supports write access to all areas
of EEPROM, negative testing is done only for Xframe I.
3. Return values from subfunctions of offline diagnostics have
been corrected.
4. In register test, expected value from rx_queue_cfg register
is made to depend on adapter type.
5. After the test, need to restore values at EEPROM offsets
0x4F0 and 0x7F0. These locations were modified as part of test.
6. Use macro SPECIAL_REG_WRITE for write access to mc_rldram_test_ctrl
register. Also, couple of unnecessary writes to mc_rldram_test_ctrl
have been removed.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Reported by: Bob Tracy <rct@gherkin.frus.com>
"...I've got a Toshiba notebook (730XCDT -- Pentium 150MMX) for which
I'm using the Vesa FB driver. When the machine has been idle for some
time and the driver attempts to powerdown the display, rather than the
display going blank, it goes gray with several strange lines. When I
hit the "shift" key or other-wise wake up the display, the old video
state is not fully restored..."
vesafb recently added a blank method which has only 2 states, powerup and
powerdown. The powerdown state is used for all blanking levels, but in his
case, powerdown does not work correctly for higher levels of display
powersaving. Thus, for intermediate power levels, use software blanking,
and use only hardware blanking for an explicit powerdown.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This still leaves driver and architecture-specific subdirectories alone,
but gets rid of the bulk of the "generic" generated files that we should
ignore.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Only signal completion after marking request slot as free, otherwise other
processor can free request structure before we finish using it.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix -EIO on /proc/acpi/events after suspends. This actually breaks
suspending by power button in many setups.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since Revision 1.10 was released the n_r3964 module wasn't able to receive any
data. The reason for that behavior is because there were some wrong calls of
mod_timer(...) in the function receive_char (...). This patch should fix this
problem and was successfully tested with talking to some kuka industrial
robots.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change makes quirk_intel_ide_combined() dependent on the precise
conditions under which it is needed:
* IDE is built in
* IDE SATA option is not set
* ata_piix or ahci drivers are enabled
This fixes an issue where some modular configurations would not cause
the quirk to be enabled.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus torvalds <torvalds@osdl.org>
During the development of an USB device I found a bug in the handling of
Highspeed HID devices in the kernel.
What happened?
Highspeed HID devices are correctly recognized and enumerated by the
kernel. But even if usbhid kernel module is loaded, no HID reports are
received by the kernel.
The output of the hardware USB analyzer told me that the host doesn't
even poll for interrupt IN transfers (even the "interrupt in" USB
transfer are polled by the host).
After some debugging in hid-core.c I've found the reason.
In case of a highspeed device, the endpoint interval is re-calculated in
driver/usb/input/hid-core.c:
line 1669:
/* handle potential highspeed HID correctly */
interval = endpoint->bInterval;
if (dev->speed == USB_SPEED_HIGH)
interval = 1 << (interval - 1);
Basically this calculation is correct (refer to USB 2.0 spec, 9.6.6).
This new calculated value of "interval" is used as input for
usb_fill_int_urb:
line 1685:
usb_fill_int_urb(hid->urbin, dev, pipe, hid->inbuf, 0,
hid_irq_in, hid, interval);
Unfortunately the same calculation as above is done a second time in
usb_fill_int_urb in the file include/linux/usb.h:
line 933:
if (dev->speed == USB_SPEED_HIGH)
urb->interval = 1 << (interval - 1);
else
urb->interval = interval;
This means, that if the endpoint descriptor (of a high speed device)
specifies e.g. bInterval = 7, the urb->interval gets the value:
hid-core.c: interval = 1 << (7-1) = 0x40 = 64
urb->interval = 1 << (interval -1) = 1 << (63) = integer overflow
Because of this the value of urb->interval is sometimes negative and is
rejected in core/urb.c:
line 353:
/* too small? */
if (urb->interval <= 0)
return -EINVAL;
The conclusion is, that the recalculaton of the interval (which is
necessary for highspeed) should not be made twice, because this is
simply wrong. ;-)
Re-calculation in usb_fill_int_urb makes more sense, because it is the
most general approach. So it would make sense to remove it from
hid-core.c.
Because in hid-core.c the interval variable is only used for calling
usb_fill_int_urb, it is no problem to remove the highspeed
re-calculation in this file.
Signed-off-by: Christian Krause <chkr@plauener.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Increased use of scatter-gather by usb-storage driver after 2.6.13 has
exposed a buggy codepath in isp116x-hcd, which was probably never
visited before: bug happened only for those urbs, for which
URB_SHORT_NOT_OK was set AND short transfer occurred.
The fix attached was tested in 2 ways: (a) it fixed failing
initialization of a flash drive with an embedded hub; (b) the fix was
tested with 'usbtest' against a modified g_zero driver (on top of
net2280), which generated short bulk IN transfers of various lengths
including multiples and non-multiples of max_packet_length.
Signed-off-by: Olav Kongas <ok@artecdesign.ee>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch from Eric fixes handling of the phy identifiers in mptsas.
I've split it up from his bigger patch as it should go into 2.6.14
still.
Signed-off-by: Eric Moore <Eric.Moore@lsil.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The patch below should make the Pioneer DRM-624X automatically
be set up with all 6 "drives". (6 slot SCSI CD changer)
Signed-off-by: Karl Magnus Kolst <karl.kolsto@uib.no>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix the fact that the svideo input will only give input in black/white in
some circumstances. Reason is that in the PCI controller driver (zr36067),
after setting input, we reset norm, which overwrites the input register
with the default. This patch makes it always set the correct value for the
input when changing norm.
Signed-off-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug #5404 in kernel bugzilla.
It basically updates the vpx3220 initialization tables with some newer
values that we've had in CVS for a while (and that, for some reason, never
ended up in the kernel... must've gotten lost). Those fix a ~16 pixels
noise at the top of the picture in at least SECAM, although (now that I
think about it) PAL was probably affected, also.
Signed-off-by: Ronald S. Bultje <rbultje@ronald.bitfreak.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix bug 5441.
I didn't know about messy programs like svgatextmode... Couldn't this be
integrated in some linux/drivers/video/console/svgacon.c ?... So because
of the existence of the svgatextmode program, the kernel is not supposed to
touch to CRT_OVERFLOW/SYNC_END/DISP/DISP_END/OFFSET ?
Disabling the check in vgacon_resize() might help indeed, but I'm really
not sure whether it will work for any chipset: in my patch, CRT registers
are set at each console switch, since stty rows/cols apply to consoles
separately...
The attached solution is to keep the test, but if it fails, we assume that
the caller knows what it does (i.e. it is svgatextmode) and then disable
any further call to vgacon_doresize. Svgatextmode is usually used to
_expand_ the display, not to shrink it. And it is harmless in the case of
a too big stty rows/cols: the display will just be cropped. I tested it on
my laptop, and it works fine with svgatextmode.
A better solution would be that svgatextmode explicitely tells the kernel
not to care about video timing, but for this an interface needs be defined
and svgatextmode be patched.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a request is deferred in scsi_init_io because the sg table could not
be allocated, the associated scsi_cmnd is not released and the request is
not marked with REQ_DONTPREP. When the command is retried, if
scsi_prep_fn decides to kill it then the scsi_cmnd will never be released.
This patch (as573) changes scsi_init_io so that it calls scsi_put_command
before deferring a request.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Juan was kind enough to linger on site, and work on a production
machine, to try the parameter to make the system stable. He discovered
that reducing the maximum transfer size issued to the adapter to 128KB
stabilized his system. This is related to an earlier change for the
2.6.13 tree resulting from Martin Drab's testing where the transfer size
was reduced from 4G to 256KB; we needed to go still further in scaling
back the request size.
Here is the patch that tames this regression.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Fix 12 undefined preprocessor identifier warnings (4 each in 3 driver builds):
drivers/scsi/NCR5380.c:2744:16: warning: undefined preprocessor identifier 'NDEBUG_ABORT'
drivers/scsi/NCR5380.c:2744:16: warning: "NDEBUG_ABORT" is not defined
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The modem is said to work with belows addition to pnp_dev_table[]:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=296011
Signed-off-by: maximilian attems <janitor@sternwelten.at>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Kernel version 2.6.13 introduced a regression in the generic USB
serial converter driver (usbserial.o, drivers/usb/serial/generic.c).
The bug manifests, as far as I can tell, whenever you attempt to write
to the device -- the write will never complete (write() returns 0, or
blocks).
Signed-off-by: Randall Nortman <oss@wonderclown.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Argument does not agree.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
drivers/built-in.o: In function `w1_alloc_dev': undefined reference to `netlink_kernel_create'
drivers/built-in.o: In function `w1_alloc_dev': undefined reference to `sock_release'
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While doing some testing of error cases I ran into this bug. In some cases
the reset handler can exit with the host_lock still held.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The aironet PCI driver has a build dependency on ISA that prevent the
driver to compile on systems that doesn't support ISA, like x86_64. The
driver really doesn't depend on ISA, it does some ISA stuff in the
initialization code, since the driver supports both ISA and PCI cards. So
the driver should depend on ISA_DMA_API to build on all systems, and this
will not hurt PCI at all.
Signed-off-by: Matteo Croce <3297627799@wind.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes depenencies of collie keyboard.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes wrong comments, non-working debug subsystem, and some
potentially dangerous macros.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This fixes compilation with CPU_FREQ disabled.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These days, in 2.6.x, even INQUIRY commands are sent using
scatter gather lists.
Bug reported by Tom 'spot' Callaway.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Richard Purdie
Correct the right shift key entry in the spitz keyboard driver.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Lothar Wassmann
The function serial_pxa_set_termios() is calling uart_update_timeout()
with the baud rate divisor as third parameter, while
uart_update_timeout() expects the baud rate in this place.
This results in a bogus port->timeout which is proportional to the
baud rate.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The s3c2410 serial driver is missing static declerations
on several functions that are not exported, and have no
need of being exported outside the driver
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the current dell_rbu code ver 2.0 the packet update mechanism makes the
user app dump every individual packet in to the driver.
This adds in efficiency as every packet update makes the
/sys/class/firmware/dell_rbu/loading and data files to disappear and reappear
again. Thus the user app needs to wait for the files to reappear to dump
another packet. This slows down the packet update tremendously in case of
large number of packets. I am submitting a new patch for dell_rbu which will
change the way we do packet updates;
In the new method the user app will create a new single file which has already
packetized the rbu image and all the packets are now staged in this file.
This driver also creates a new entry in
/sys/devices/platform/dell_rbu/packet_size ; the user needs to echo the packet
size here before downloading the packet file.
The user should do the following:
create one single file which has all the packets stacked together.
echo the packet size in to /sys/devices/platform/dell_rbu/packet_size.
echo 1 > /sys/class/firmware/dell_rbu/loading
cat the packetfile > /sys/class/firmware/dell_rbu/data
echo 0 > /sys/class/firmware/dell_rbu/loading
The driver takes the file which came through /sys/class/firmware/dell_rbu/data
and takes chunks of paket_size data from it and place in contiguous memory.
This makes packet update process very efficient and fast. As all the packet
update happens in one single operation. The user can still read back the
downloaded file from /sys/devices/platform/dell_rbu/data.
Signed-off-by: Abhay Salunke <abhay_salunke@dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Search for a disconnect ccw_device on the ccw bus rather than on the css
bus (was a typo in patch I did for the klist conversion). A cast to an
embedding ccw_device from an embedded device in a struct subchannel will
lead us to oopses.
Signed-off-by: Cornelia Huck <cohuck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
for certain NICs
Reverting 685fac63f5:
> [PATCH] e100: CPU cycle saver microcode
>
>
> Add cpu cycle saver microcode to 8086:{1209/1229} other than ICH devices.
>
> Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
> Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
> Signed-off-by: John Ronciak <john.ronciak@intel.com>
> Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Incorrect uart_write_wakeup() calls cause reference to a
NULL tty pointer in sunsab and sunzilog serial drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
All the same issues - we can't just save the pointer to the thread, we
must save the pid/uid/euid combination.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If a process issues an URB from userspace and (starts to) terminate
before the URB comes back, we run into the issue described above. This
is because the urb saves a pointer to "current" when it is posted to the
device, but there's no guarantee that this pointer is still valid
afterwards.
In fact, there are three separate issues:
1) the pointer to "current" can become invalid, since the task could be
completely gone when the URB completion comes back from the device.
2) Even if the saved task pointer is still pointing to a valid task_struct,
task_struct->sighand could have gone meanwhile.
3) Even if the process is perfectly fine, permissions may have changed,
and we can no longer send it a signal.
So what we do instead, is to save the PID and uid's of the process, and
introduce a new kill_proc_info_as_uid() function.
Signed-off-by: Harald Welte <laforge@gnumonks.org>
[ Fixed up types and added symbol exports ]
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Nicolas Pitre
drivers/mfd/ucb1x00-core.c: In function 'ucb1x00_probe':
drivers/mfd/ucb1x00-core.c:482: error: 'ucb1x00_class' undeclared (first use in this function)
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The logic in ide_do_request() doesn't guarantee that both drives will be
serviced after a call. It may "forget" to service one in some
circumstances, including when one of the drive is suspended (it will
eventually fail to service the slave when the master is suspended for
example). This prevents the wakeup requests that gets queued on wakeup
from sleep from beeing serviced in some cases when 2 drives are sharing
an IDE bus.
The problem is deep enough in the way this code works (and there are
probably a few other problematic but rare corner cases) and fixing it
would require some major rethinking of the way IDE decides which channel
to service. This is not 2.6.14 material. However, in the meantime,
Bart has accepted this simple workaround that will fix the crash on
wakeup from sleep since this specific corner case is actually hitting
users to get into 2.6.14.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The pccardd thread has a race in it that it can shutdown in the
TASK_INTERRUPTIBLE state.
Make sure we mark ourselves runnable again as we remove ourselves from
the wait queue.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Ben Dooks
Initialise the driver's .owner field so that
the device driver can be referenced to the
module that owns it
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
Add initialisation of .owner field so that
the device driver can be referenced to the
module that owns it.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds support for sil_3131 and sil_3531. Both are
identical to 3124 except that they have only one port. Bits 30 and 31
of ata_port_info->host_flags is used to encode available port numbers.
Version number is bumped to 0.22.
Edward Falk supplied all the necessary information and preliminary
patch.
Signed-off-by: Tejun Heo <htejun@gmail.com>
- change "xlat" and "fill" actors in libata-scsi so
they are responsible for SCSI status and sense data
when they return 1. This allows GOOD status or a
specialized error to be set.
- yield an error for mode sense requests for saved
values [sat-r06]
- remove static inlines for ata_bad_scsiop() and
ata_bad_cdb() which are no longer used
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add extern ata_scsi_set_sense() to build SCSI
fixed sense data and corresponding SCSI status
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- added typedef unsigned int __nocast gfp_t;
- replaced __nocast uses for gfp flags with gfp_t - it gives exactly
the same warnings as far as sparse is concerned, doesn't change
generated code (from gcc point of view we replaced unsigned int with
typedef) and documents what's going on far better.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should not be warning about commands that we allow, even if they are
unknown. So move the if-root-allow check up a notch.
Signed-off-by: Jens Axboe <axboe@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(struct pcmcia_socket).tune_bridge only exists if CONFIG_CARDBUS is set
but building yenta_socket without CardBus is valid.
Signed-off-by: David Vrabel <dvrabel@arcom.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch fixes the p9100 framebuffer so that text is viewable
(not black on black, like it was before the patch). The linux logo
displays for a very short period of time, then is replaced by a grey
box. This leads me to believe that this framebuffer would have problems
in X, but since there hasn't been a weitek driver for X in several
millennia, this isn't something that I can confirm or deny.
But this patch does get color console working on my SPARCbook 3TX.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Hello, guys.
This patch implements ->tf_read callback for sil24. It didn't use to
be necessary but new ata_gen_fixed_sense now makes use of ->tf_read
callback. This patch is taken from Edward Falk's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
drivers/mfd/ucb1x00-core.c:555: error: static declaration of 'ucb1x00_class' follows non-static declaration
drivers/mfd/ucb1x00.h:109: error: previous declaration of 'ucb1x00_class' was here
Since ucb1x00_class isn't used by anything, remove the extern
declaration and the symbol export.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
03_sil24_add-tf-reading.patch
This patch implements proper TF register reading back and
caching and bumps up version to 0.22. This is taken from
Edward's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 50 +++++++++++++++++++++++++++++++++++++++++++++-----
1 file changed, 45 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
01_sil24_ignore-non-error-exception-irqs.patch
Do not error-finish commands for non-error exception irqs -
just ignore them. This is taken from Edward's driver.
Signed-off-by: Tejun Heo <htejun@gmail.com>
sata_sil24.c | 11 ++++++++++-
1 file changed, 10 insertions(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This should fix up lockups that people were seeing due to
improper spinlock placement. Also, the start/stop DMA routines put
guarded trust in the cached state of DMA.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
1) note urgent bug, that completes command twice
2) only fix up INQUIRY data if the SCSI version is zero (typically
indicates ATAPI MMC-ish device)
3) if there is a problem on the ATA bus, don't bother with REQUEST
SENSE, just directly handle the error based on Status/Error registers.
Fix implicit nocast warnings in connector code:
drivers/connector/connector.c:102:24: warning: implicit cast to nocast type
drivers/connector/connector.c:114:45: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix implicit nocast warnings in bonding code:
drivers/net/bonding/bond_main.c:1302:49: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix implicit nocast warnings in atm code:
net/atm/atm_misc.c:35:44: warning: implicit cast to nocast type
drivers/atm/fore200e.c:183:33: warning: implicit cast to nocast type
Also use kzalloc() instead of kmalloc().
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The orinoco driver can send uninitialized data exposing random pieces of
the system memory. This happens because data is not padded with zeroes
when its length needs to be increased.
Reported by Meder Kydyraliev <meder@o0o.nu>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
On several failure exits in ibmtr we end up doing kfree() on dev->priv,
with dev allocated by alloc_trdev() and ->priv never reassigned.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
megaraid_sas depends on arch-specific indirect includes pulling
fs.h in; on alpha they do not.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CONFIG_SGI_MBCS is enabled in generic kernels, but the driver may
oops some other platforms. Check whether we are running on sn2
and bail out if we are not before doing anything dangerous.
Acked-by: Bruce Losure <blosure@americas.sgi.com>
Signed-off-by: Greg Edwards <edwardsg@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This redoes the n_ports logic I proposed before as a bitmask.
ata_pci_init_native_mode is now used with a mask allowing for mixed mode
stuff later on. ata_pci_init_legacy_port is called with port number and
does one port now not two. Instead it is called twice by the ata init
logic which cleans both of them up.
There are stil limits in the original code left over
- IRQ/port mapping for legacy mode should be arch specific values
- You can have one legacy mode IDE adapter per PCI root bridge on some systems
- Doesn't handle mixed mode devices yet (but is now a lot closer to it)
Replicate IGMP frames across all slaves in activebackup mode. This
ensures fail-over is rapid for multicast traffic as well. Otherwise,
multicast traffic will be lost until the next IGMP membership report
poll timeout.
This is conceptually similar to the treatment of IGMP traffic in
bond_alb_xmit. In that case, IGMP traffic transmitted on any slave
is re-routed to the active slave in order to ensure that multicast
traffic continues to be directed to the active receiver.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Use the size of the target array for the length argument to strncpy
instead of the size of the source or a magic number.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Cisco Aironet doesn't resume properly from swsusp, because the resume
method confuses a PM_EVENT_* for a PCI power state. It thinks that it is
resuming from PCI_D1 and doesn't do the necessary initialization of the
card.
Signed-off-by: Michal Schmidt <xschmi00@stud.feec.vutbr.cz>
Flush shadow RAM to save updates to ASF related bits for 82573 controllers.
These bits are past the first 63 words of NVM.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
added msleep_interruptible delay right before returning from diag_test to allow
the phy to recover from reset
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fixes for packet split related issues
* On platforms where PAGE_SIZE > 4K, driver will use only required number of
pages compared to always using 3 pages.
* Packet split won't be used if the PAGE_SIZE is > 16K
* Adds a statistics counter to splits.
* Setting the non Null ptr to zero sized buffers to solve packet split
receive descriptor error
* When the no of pages needed is calculated, the header buffer is not
included for a given MTU.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Enable custom configuration bits for 82571/2 controllers. The bits are
required for correct functionality of these controllers.
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
defines/modifies data structures, function prototypes and changes to the
driver rendering it capable of handling <n> tx/rx queues
Signed-off-by: Mallikarjuna R Chilakala <mallikarjuna.chilakala@intel.com>
Signed-off-by: Ganesh Venkatesan <ganesh.venkatesan@intel.com>
Signed-off-by: John Ronciak <john.ronciak@intel.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for MSI/MSI-X feature to the driver. It is
a runtime parameter(for now, loadable parameter). Default is INTA.
Patch has been tested on IA64 platform with Xframe II adapter,
both of which support MSI-X feature. An improvement of about 7%
in throughput(both Tx and Rx) was observed and a reduction by 7%
in CPU utilization during Tx test.
Signed-off-by: Ravinandan Arakali <ravinandan.arakali@neterion.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix nocast sparse warnings in sungen:
drivers/net/sungem.h:1040:45: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix implicit nocast warnings in ns83820 code, including __nocast:
drivers/net/ns83820.c:603:46: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Unfortunately, [your patch] might address the crash but doesn't address
the real problem. It turns out that the problem is one of padding
(the firmware cksum engine works only on 32-bit chunks, yuck), so
the special casing for length == 1 wasn't sufficient anyway.
This patch addresses the issue, as well the other issue of i386 +
CONFIG_HIGHMEM being broken. It is pretty much the same workaround
that Adaptec themselves used in their Windows driver. I have yet to
check if it fixes the problem when the skb is non-linear, but this
patch _will_ solve the problem for 99% of the users out there (those
not using sendfile).
Signed-off-by: Ion Badulescu <ionut@badula.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch changes pocket and parallel adaptors to depend on PARPORT
instead of ISA in order to get the option in newer SuperIO based systems.
Signed-off-by: Grant Coady <gcoady@gmail.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support to the ibm_emac driver for platform-specific
unsupported PHY features.
The patch attempts to determine the highest speed and duplex when
autonegotiation is unsupported.
Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The patch below is necessary to allow my Digital DS21143 Tulip rev 48
ethernet interface to work in a 10Mbit Half Duplex network. Without
it, the driver keeps retrying other modes in an endless loop. It seems
like someone already had the same problem with a rev 65 board :)
Signed-off-by: Philippe De Muyter <phdm@macqel.be>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
David S. Miller <davem@davemloft.net> wrote:
>I think removing support for older ifenslave binaries is
>the least painful solution to this problem.
This patch removes backwards compatibility for old ifenslave
binaries (ifenslave prior to verison 1.0.0).
I did not similarly modify ifenslave itself; with sysfs on the
horizon, I don't see that as being worthwhile.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is my libata compatible low level driver for the Marvell SATA
family. Currently it runs in DMA mode on a 6081 chip.
The 5xxx series parts are not yet DMA capable in this driver because
the registers have differences that haven't been accounted for yet.
Basically, I'm focused on the 6xxx series right now. I apologize for
those seeing problems on the 5xxx series, I've not had a chance to
look at those problems yet.
For those curious, the previous bug causing the SCSI timeout and
subsequent panics was caused by an improper clear of hc_irq_cause in
mv_host_intr().
This version is running well in my environment (6081 chips,
with/without SW raid1) and is showing equal or better performance
compared to the Marvell driver (mv_sata) in my initial tests (timed
dd's of reads/writes to/from memory/disk).
I still need to look at the causes of occasional problems such as this:
ata11: translating stat 0x35 err 0x00 to sense
ata11: status=0x35 { DeviceFault SeekComplete CorrectedError Error }
SCSI error : <10 0 0 0> return code = 0x8000002
Current sda: sense key Hardware Error
end_request: I/O error, dev sda, sector 3155010
and this, seen at init time:
ATA: abnormal status 0x80 on port 0xE093911C
but they aren't showstoppers.
Signed-off-by: Brett Russ <russb@emc.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch introduces new feature in qeth:
qeth enhancement provides the device driver support for
the Communication Controller for Linux on System z9 and zSeries
(CCL), which is software that enables running the Network Control
Program (NCP) on a zSeries machine. The OSA CDLC support is based
on a new IBM mainframe CHPID type called Open Systems Adaper for
NCP (OSN). In case of OSN qeth communicates with the type-OSN
OSA-card on one hand, and with the CCL-kernel-component Network
Device Handler (NDH) on the other.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
From: Peter Tiedemann <ptiedem@de.ibm.com>
From: Frank Pavlic <pavlic@de.ibm.com>
minor qeth fixes:
- free old skb in qeth_realloc_headroom after duplicating skb
- disable IPV6 support for Hipersockets devices
- call ccw_device_set_offline on every channel regardless
of the return value of the prior ccw_device_set_offline calls
- allocate qdio structures in DMA-area
- schedule recovery of appropriate card
when cable has been inserted again.
- add missing initialization of card->lock
- write sequence number in skb->cb for SNA protocol which
requires strictly serialized packets.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
diffstat:
qeth.h | 2 ++
qeth_main.c | 37 +++++++++++++++++--------------------
2 files changed, 19 insertions(+), 20 deletions(-)
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The smc91c92_cs multicast does not work
if the count of multicast address is 1.
Signed-off-by: <komurojun-mbn@nifty.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Fix implicit nocast warnings in ns83820 code:
drivers/net/ns83820.c:603:46: warning: implicit cast to nocast type
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Unregister all netdevs before freeing local data. I was unable to
trigger any crashes without this change when running busy loops for
driver operations when ejecting a Prism2 PC Card. Anyway, should there
be a race condition with this, better make it less likely to happen by
unregistering the netdevs first.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
local->hw_priv was being freed and set to NULL just before calling
prism2_free_local_data(). However, this may expose a race condition in
which something ends up trying to use hw_priv during shutdown. I
haven't noticed this happening, but better be safe than sorry, so
let's postpone hw_priv freeing to happen only after
prism2_free_local_data() has returned.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
The debug version of I/O functions in hostap_pci had not survived the
change to start using hw_priv pointer, so let's fix them to actually
define the local hw_priv variable.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Host AP driver used hardware model specific dev_open/close handlers
that were called on dev_open/close if the hardware driver had
registered the handler. These were only used for hostap_cs and only
for tracking whether any of the netdevs were UP. This information is
already available from local->num_dev_open, so there is not need for
the special open/close handler.
Let's get rid of these handlers. In addition to cleaning up the code,
this fixes a module refcounting issue for hostap_cs where ejecting the
card while any of the netdevs were open did not decrement refcount
properly.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Skge driver was bringing link up/down when changing mac
address. This doesn't work in the bonding environment, and is
more effort than needed.
Fixes-bug: http://bugzilla.kernel.org/show_bug.cgi?id=5271
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Since our max_lun is unconditionally set to 1, we might as well
hardcode a LUN 0 probe, rather than a wildcard LUN scan.
The ide-scsi driver sets max_lun to a value greater than under
certain conditions:
if ((drive->id->last_lun & 0x7) != 7)
host->max_lun = (drive->id->last_lun & 0x7) + 1;
else
host->max_lun = 1;
last_lun is Word 126 of IDENTIFY PACKET DEVICE, marked as obsolete
and undocumented in non-ancient specs. We'll leave it out for now.
Should the need arise to support multi-LUN ATAPI devices, we'll
probably want to add the above code.
Finally, there have been reports of REPORT LUNS commands locking up
ATAPI drives. Eliminating the wildcard LUN scan could help reduce
the trouble from problematic drives.
The lock is not held when calling this function, so we
shouldn't drop then reacquire it.
Based upon a report from Jim MacBaine.
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch renames __in_dev_get() to __in_dev_get_rtnl() and
introduces __in_dev_get_rcu() to cover the second case.
1) RCU with refcnt should use in_dev_get().
2) RCU without refcnt should use __in_dev_get_rcu().
3) All others must hold RTNL and use __in_dev_get_rtnl().
There is one exception in net/ipv4/route.c which is in fact a pre-existing
race condition. I've marked it as such so that we remember to fix it.
This patch is based on suggestions and prior work by Suzanne Wood and
Paul McKenney.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Test for VIA K8T800 north bridge instead of AMD K8 HyperTransport
bridge based on new information from Andi Kleen. The AMD
HyperTransport interface is not responsible for PCI transactions
and so the re-ordering is more likely done by the VIA north bridge.
This code is subject to change if we get more information from AMD
or VIA.
PCI Express devices are excluded from doing the read flush since all
chipsets in the write_reorder list are PCI chipsets.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace SCSI's legacy "bang at the door" method of probing with one
directly controlled by the underlying ATA transport layer.
We now only call scsi_scan_target() for devices we find, rather than
probing every possible channel/id within a certain range.
Some Legacy megaraid cards can't actually cope with the scatter/gather
version of the READ CAPACITY command (which is what we now send them
since altering all SCSI internal I/O to go via the block layer). Fix
this (and a few other broken megaraid driver assumptions) by sending
the non-sg version of the command if the sg list only has a single
element.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In these drivers, scsi_remove_host() is called too late, at the point
it is called, the driver has already shut down too far to accept any
I/O that the shutdown might generate. Any generated I/O actually
triggers a panic.
Fix this by calling scsi_remove_host() as early as possible and not
calling scsi_host_put() until just before we kfree the ahc_softc.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's a problem in our host release in that it calls
scsi_proc_hostdir_rm(). However, if you hold a reference to the host as
you remove the module, the host template (which proc uses) will be freed
and the system will panic when the host device is finally released.
Fix this by moving scsi_proc_hostdir_rm() to where it should be: in
scsi_remove_host().
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Arrange for the initialisation printks to happen after we've
registered the network interface, so we know what name the
device is. Also, check the link every 500ms (and use
msecs_to_jiffies.)
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds suspend support for the Radeon M11 chip in 12" iBooks
manufactured after July 2005. I don't know if the new 14" iBooks also
have that chip, so they might also be supported.
The chip identifies itself as "RV350 NV" (pci id 0x4e56), revision 0x80.
Apple calls it "Snowy", xfree86 names it "ATI FireGL Mobility T2 (M11)
NV (AGP)". So, we seem to be lucky here: The suspend-code for the M10
(which also is a "RV350 NV") works flawless for that chip.
Signed-off-by: Sven Henkel <shenkel@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Vincent Sanders
When building the mx1ads ARM platforms the serial driver fails to compile
with GCC 4.01 due to extern/static ambiguity.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tone down the r8169 driver
As an alternative, people can use the boot time 'debug' option and/or use
'ethtool -s ethX msglvl xyz'. The different messages are listed at:
http://www.zoreil.com/~romieu/r8169/doc/msglvl.txt
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remember to free the multicast group context memory table.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
less noise in dmesg
Signed-off-by: Ben Collins <bcollins@debian.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
amdtp, dv1394, raw1394, video1394:
Delete legacy module aliases. The macros did not work and the aliases are not
needed nowadays.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@debian.org>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Work around limitation in rawiso routines. Required with 1394b cards on
architectures where PAGE_SIZE is 4096. Based on a previous patch by Ben
Collins.
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
trivial edits of a few comments
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@debian.org>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Use of time_before() macro, defined at linux/jiffies.h, which deal with
wrapping correctly and are nicer to read.
Signed-off-by: Marcelo Feitoza Parisi <marcelo@feitoza.com.br>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Ben Collins <bcollins@debian.org>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix debug code so it prints the correct speed (was defaulting to 100, so
anything > 400 showed only 100).
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Ben Collins <bcollins@debian.org>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Skip a superfluous pause that occured when the config ROM of a node was
scanned unsuccessfully. This also occurs if a node without link wrongly
enables its "link active" self ID flag. A GWCTech 6-port hub does this.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Units were not detected if the local IRM performed a bus reset. ("The root
node is not cycle master capable; selecting a new root node and resetting...",
often seen with iPods and other SBP-2 devices). Rearrange the order of IRM
duties and node scanning. TODO: Audit the ROM caching and parsing code for
underlying issues.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Set serialize_io=1 by default. This is safer and required by seemingly more
and more hardware. It causes little or no performance loss for S400 devices.
Performance of S800 1394b devices may drop by 25...30%. Therefore make the
parameter's description and dmesg message clearer about performance impact.
Update description of the max_speed parameter too. IEEE1394_SPEED_MAX is
currently S800.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fixes for deadlocks of the ieee1394 and scsi subsystems and long delays in
futile error recovery attempts when SBP-2 devices are removed or drivers are
unloaded.
- Complete commands quickly with DID_NO_CONNECT if the 1394 node is gone or if
the 1394 low-level driver was unloaded.
- Skip unnecessary work in the eh_abort_handler and eh_device_reset_handler if
the node or 1394 low-level driver is gone.
- Let scsi's high-level shut down gracefully when sbp2 is being unloaded or
detached from the 1394 unit. A call to scsi_remove_device is added for this
purpose, which requires us to store a scsi_device pointer.
- scsi_device pointer is obtained from slave_alloc hook and cleared by
slave_destroy. This avoids usage of the pointer after the scsi device was
deleted e.g. by the user via scsi_mod's sysfs interface.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Jody McIntyre <scjody@steamballoon.com>
Cc: Ben Collins <bcollins@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This change removes a bogus error message from the IOC4 serial driver
interrupt handler.
This error message is bogus for two reasons. First, it can never occur
given that current code takes care to initialize IOC4 in such a way that
these "unknown" interrupts could never occur. Second, this code fails to
take into account that other drivers can share the IOC4 interrupt mechanism
through SA_SHIRQ, and thus this driver is not in-fact "all-knowing".
Finally, this error message triggers every time some "unknown" interrupt
occurs -- it's not rate limited or repetition limited in any way, thereby
effectively denying use of the console device. Given its bogosity in the
first place, it's best to just get rid of it entirely.
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
GPIO fix for the composite and tv mute states of bt8xx card #135: DViCO
FusionHDTV5 Lite. Without this patch, selecting one of these states could
produce unexpected behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
the free_irq() in USB suspend breaks resume on some setups where USB
(ohci/ehci) shares the interrupt with an other device.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The driver does a readl() on DEVICE_ID which is 2-byte aligned and
2-bytes in size. It's doing this read just to flush write buffers.
Create IN16() and OUT16() macros, and use the former to do this I/O
load.
Signed-off-by: David S. Miller <davem@davemloft.net>
The SMU driver has a small mistake in the locking of the interrupt code,
if polled access and interrupt access race, interrupt may take a lock
and return without releasing it. This fixes it. With that patch, the
driver is rock solid with my experimental thermal control (which bangs
it pretty hard) racing with real time clock and cpufreq handling.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The function s3c2410fb_activate_var does not return
a value, therefore it should be declared void.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Workaround for the ioremap patch that produces a blank display on some
chipsets
- Make hwcursor = 0 the default. The hardware cursor does not work with all
hardware.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- use nonseekable_open() instead of messing with
if (*ppos != file->f_pos)
return -EISPIPE
in ->write() (->read is NULL).
- trivial __user annotations
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- print pointers with %p
- casting pointer structure field to int and printing it with %d...
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bunch of create_proc_dir_entry() calls creating directories had crept
in since the last sweep; converted to proc_mkdir().
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
* Clean-up control status code (use control status defines +
change pcipcwd_clear_status)
* Clean-up boot-code (move card info to pcipcwd_show_card_info() )
Signed-off-by: Wim Van Sebroeck <wim@iguana.be>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since asm/hardware.h's only reason for existing is to include
asm/arch/hardware.h, it's completely pointless to include both.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix warning:
drivers/video/pxafb.h:119:5: warning: "DEBUG" is not defined
by removing the whole
#if DEBUG
#define DPRINTK(fmt, args...) printk...etc...
#else
#define DPRINTK(fmt, args...)
#endif
stuff - we have pr_debug() for this.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rename IPoIB driver's path_lookup() to ipoib_path_lookup() to avoid a
clashes with the kernel global path_lookup(). We don't hit this with
the current kernel source, but some external patches seem to trigger
this, and it's cleaner to avoid clashing with global names anyway.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
refs/heads/for-linus
Only start up nonstatic sockets if both IO and MEM resources are available.
Thanks to Russell King and Matthew Wilcox for tracking this down.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Changes:
s/PIO_ST_/HSM_ST_/ and s/pio_task_state/hsm_task_state/.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
When creating a multipath device, if the queue_if_no_path parameter is
specified it gets ignored.
While the queue_if_no_path variable is correctly set to 1, the
saved_queue_if_no_path gets set to 0. When the device is subsequently made
live (resumed), the saved value (0) always overwrites the live value (1) so
the option *always* gets turned off.
The fix adds a parameter to the queue_if_no_path() function to indicate
whether the previous value should be preserved or not - if not, as when the
device is being set up, the saved value is set to the new value (1).
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If anything is waiting on a device's table when the device is removed, we
must first wake it up so it will release its reference. Otherwise the
table's reference count will not drop to zero and the table will not get
removed.
Signed-Off-By: Alasdair G Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Latest wireless extensions moved a field from netdev -> wireless_handlers.
The WE core will now printk a warning on every call to get_wireless_stats()
on a driver that still uses the old field. This patch fixes orinoco.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Put the IPMI poweroff_powercycle parameter into sysfs. This field is
dynamically settable and is valuable to have in sysfs.
Signed-off-by: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Ralph Metzler wrote:
> AFAIR, there is a bug in tda10021.c in tda10021_readreg() which
> references state->frontend.dvb->num
> This is fatal if the frontend is not at the probed address and thus
> not yet registered (no dvb entry set yet -> NULL pointer ...).
The attached patch should get rid of the oops.
Signed-off-by: Jon Burgess <jburgess@uklinux.net>
Cc: Johannes Stezenbach <js@linuxtv.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Written by Adrian Sun (asun@darksunrising.com).
Ported to 2.6.x by Tom 'spot' Callaway <tcallawa@redhat.com>.
Further cleaned up and integrated by David S. Miller
Signed-off-by: David S. Miller <davem@davemloft.net>
The IB spec defines the field to be 32 bits, not 16 bits.
Signed-off-by: Jack Morgenstein <jackm@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Fix interrupt test handler by adding check for IRQ assertion in
PCI_STATE register in addition to the status block updated bit.
Add test for valid ethernet address in tg3_set_mac_addr().
Add tg3_bus_string() to setup the PCI bus speed/width string for all
PCI/PCIX/PCI Express devices. This is used to print the bus type
during init_one().
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix 5780 PHY related problems:
1. MAC_RX_MODE reset must be done before setting up the MAC_MODE
register on 5705_PLUS chips or the chip will stop receiving after
a while. The MAC_RX_MODE reset is needed to prevent intermittently
losing the first receive packet on serdes chips.
2. Skip MAC loopback test on 5780 because of hardware errata. Normal
traffic including PHY loopback is not affected by the errata.
3. PHY loopback fails intermittently on 5708S and this is fixed by
putting the PHY in loopback mode first before programming the MAC
mode register. A MAC_RX_MODE reset is also added.
4. Return -EINVAL in tg3_nway_reset() if device is in TBI mode. Allow
nway_reset if 5780S is in parallel detect mode.
5. Add missing PHY IDs in KNOWN_PHY_ID() macro.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating a table for mem-free HCA context, don't assume that
obj_size * nobj is an even multiple of MTHCA_TABLE_CHUNK_SIZE. In
particular, make sure we allocate at least one slot even if the table
is smaller than MTHCA_TABLE_CHUNK_SIZE.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Received from Mark Salyzyn from Adaptec.
High Priority Queues have *never* been used in the entire history of the
aac based adapters. Associated with this, aac_insert_entry can be
removed, SavedIrql can be removed & padding variable can be removed.
With the movement of SavedIrql out & replaced with an automatic variable
qflags, the locking can be refined somewhat. The sparse warnings did not
catch the need for byte swapping in the 'dprintk' debugging print
macros, so fixed this up when this code was moved outside of the now
refined locking.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
The size of the command packet's scatter gather list maximum size was
miscalculated in the low range leading to the driver initialization
limiting the maximum i/o size that could go to the Adapter. There were
no negative operational side effects resulting from this bad math, only
a subtle limit in performance of the Adapter at the top end of the
range.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
In the rare instances where the adapter, or the motherboard, is
misbehaving; driver initialization or shutdown becomes problematic. By
introducing a 3 minute timeout on the first interrupt driven command
during initialization, or the issuance of the adapter shutdown command
during driver unload, we can resolve the lockup problems induced by
common (but rare) hardware misbehaviors.
The timeout during initialization, should it occur, is accompanied by a
message presented to the console and the logs indicating that the user
should inspect and resolve problems with interrupt routing.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This patch adds some additional error return checking and error return
value propagation during initialization. Also, the deprecation of
pci_module_init with pci_register_driver along with the change in return
values.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
Hotplug sniffs the AIFs (events) from the adapter and if a container
change resulting in the device going offline (container zero), online
(container zero completed) or changing capacity (morph) it will take
actions by calling the appropriate API.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Recevied from Mark Salyzyn from Adaptec.
Aif pre-allocation is used to pull the kmalloc outside of the locks.
Applies to the scsi-misc-2.6 git tree.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Received from Mark Salyzyn from Adaptec.
There are a few adapters that are capable of creating devices with this large
of a capacity, but now that we have the large fib support in, the management
applications will be capable of generating them. The problem is, once they are
created, the driver will not be able to access the devices correctly without
this patch.
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If input message rate from userspace is too high, do not drop them,
but try to deliver using work queue allocation.
Failing there is some kind of congestion control.
It also removes warn_on on this condition, which scares people.
Signed-off-by: Evgeniy Polyakov <johnpol@2ka.mipt.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
Al Viro pointed out that the current IB userspace verbs interface
allows userspace to cause mischief by closing file descriptors before
we're ready, or issuing the same command twice at the same time. This
patch closes those races, and fixes other obvious problems such as a
module reference leak.
Some other interface bogosities will require an ABI change to fix
properly, so I'm deferring those fixes until 2.6.15.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The loop in mthca_map_cmd() would fill one entry past the end of the
mailbox buffer before calling the firmware command.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
We should use the first word of the clear interrupt register if
the bit we're after is < 32, not < 31.
Signed-off-by: Michael S. Tsirkin <mst@mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
If we allocate a bunch of doorbell records and then free them, we'll
end up with completely empty pages, which we then free. However, when
we come back to allocate more doorbell pages, we have to reallocate
those empty pages rather than always trying to take a slot that we've
never used. If we don't, we eventually use up every slot and fail to
allocate a doorbell record, even though we have plenty of free space.
Signed-off-by: Roland Dreier <rolandd@cisco.com>
Christian Zoz reported there are multiple NinjaATA devices all sharing the
second product ID string, but not the first one.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Adds better support for the CB-710, CB-712, CB-720 and CB-722 bridges from EnE
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Add new ID to serial_cs.c; the CIS fimware override is available by the
manufacturer at http://www.sierrawireless.com . Remember to name the CIS
binary SW_7xx_SER.cis and to put it into /lib/firmware/
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Support some more TI cardbus bridges. most of them are multifunction
devices which adds 1394 controllers, smartcard readers etc. this could
also help with the various problems with the XX21 controllers seen on the
linux-pcmcia list.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
TCIC depends on ISA. It is used with ISA-bus system only.
Signed-off-by: komurojun-mbn@nifty.com
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
pci_set_power_state is not needed, as we call pci_enable_device() somewhere
else. Also, the resource we write to PCI_BASE_ADDRESS_0 needs to be converted
to bus-centric view first.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
In interrupt probing (both ISA and PCI) the bridge control register is used
to change interrupt routing to ISA or PCI by changing bit 7. But this bit
only controls the routing of card functional interrupts, not the CSC
interrupts which are used for interrupt probing.
A bad side effect of messing with this register in yenta_probe_irq() is
that it can lead to irq storms if a card is inserted and already powered by
the BIOS.
Usage in yenta_sock_init() and yenta_config_init() seem to be fishy as well.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Echo Audio cardbus products are known to be incompatible with EnE bridges.
in order to maybe solve the problem a EnE specific test bit has to be set,
another cleared...but other setups have a good chance to break when just
forcing the bits. so do the whole thingy automatically.
The patch adds a hook in cb_alloc() that allows special tuning for the
different chipsets. for ene just match the Echo products and set/clear the
test bits, defaults to do the same thing as w/o the patch to not break
working setups.
Signed-off-by: Daniel Ritz <daniel.ritz@gmx.ch>
Cc: Linus Torvalds <torvalds@osdl.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Brown paperbag bug: sas_rphy_delete was ordered completely
wrong. Fix it up to be the same order as sas_phy_delete or
fc_rport_terminate and fix rphy objects that leaked after module
removal.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Patch from Ben Dooks
Fix the following warnings produced from
drivers/char/s3c2410.c.
drivers/serial/s3c2410.c:757: warning: 'clk' may be used uninitialized
drivers/serial/s3c2410.c:756: warning: 'clksrc' may be used uninitialized
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch fixes a hole in the rport unblock handling when processing
fabric events via the ADISC/PLOGI device state machine. Original code
would not properly 'unblock' the port upon the port reloging into the
fabric.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Currently we just ignore the device, which means there are a few
arrays out there that we don't find.
This patch updates the scsi_report_lun_scan() to take a target instead
of a device so it can be called on a return of
SCSI_SCAN_TARGET_PRESENT, which is what a PQ 3 device returns.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The wwitch bitmap was added to input_device_id structure and we should
check it when matching handlers and input devices.
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that we are compiling with -fno-strict-aliasing (this is the
kernel default), we can drop the following kludge for
iwe_stream_add_event().
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This patch adds support for WE-19 to the HostAP driver. One of
the major change is the use of an explicit flag to tell if iwstat is
in dBm or not.
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
hostap_pci and hostap_plx drivers still use PCI driver names
"prism2_pci" and "prism2_plx" respectively. This is unfriendly to
linux-wlan-ng, which uses the same names. So, if e.g. hostap_pci and
prism2_pci are loaded, they will "share" /sys/bus/pci/drivers/prism2_plx
directory.
Change PCI driver names of hostap_pci and hostap_plx to be equal to
their module names.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Jouni Malinen <jkmaline@cc.hut.fi>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
This is one of those workarounds sucked over from sk98lin driver.
The skge driver needs to detect the Yukon-Lite A0 chip properly,
and turn of Rx FIFO Flush.
Signed-off-by: Stephen Hemminger <shemminger@osdl.org>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
I found an inconsistent spin_lock usage in ipmi_smi_msg_received.
Signed-off-by: Hironobu Ishii <hishii@soft.fujitsu.com>
Cc: Corey Minyard <minyard@acm.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix this:
drivers/video/aty/xlinit.c: In function `atyfb_xl_init':
drivers/video/aty/xlinit.c:256: warning: ISO C90 forbids mixed declarations and code
- repair some kooky coding style
- Use ARRAY_SIZE()
Cc: Tom 'spot' Callaway <tcallawa@redhat.com>
Cc: "Antonino A. Daplas" <adaplas@pol.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
usb_unlink_urb is always async now, so URB_ASYNC_UNLINK was removed from
core USB and we must do as well.
Signed-off-by: Karsten Keil <kkeil@suse.de>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I believe the change that broke things is introduction of
pci_fixup_parent_subordinate_busnr().
The patch here does two things:
- hunk #1 should fix the problems you've seen when you boot without
additional "pci" kernel options;
- hunk #2 supposedly fixes boot with "pci=assign-busses" option which
otherwise hangs Acer TM81xx machines as reported.
Please try this with and without "pci=assign-busses". If it boots,
I'd like to see 'lspci -vvx' for both cases.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
While this is true, E8390_CMD is zero on i386, and thus there should be no
effect for these machines. Machines like Mac, Amiga etc. which use Alan's
clever register mapping may have a non-zero E8390_CMD and result in bogus
"transmitter busy" type messages from this bug.
Fixes BUG# 3991.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Read only needed data in __orinoco_ev_txexc().
Don't read the 802.11 header beyond addr1. The rest of the frame is not
used currently.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Annotate endianess of variables and structure members.
Don't reuse variables for both host-endian and little-endian data.
Minor comment changes in affected structures.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Remove unneeded forward declarations.
Also reorder struct pcmcia_driver initialization to keep attach and
detach together.
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
