It was set as an NMI, but the NMI bit always forces an interrupt
to end up at vector 2. So it was never used. Remove.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix
CC arch/x86_64/kernel/nmi.o
linux/arch/x86_64/kernel/nmi.c: In function ???check_nmi_watchdog???:
linux/arch/x86_64/kernel/nmi.c:155: warning: statement with no effect
on Uniprocessor builds.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch uses a static PDA array early at boot and reallocates processor PDA
with node local memory when kmalloc is ready, just before pda_init.
The boot_cpu_pda is needed since the cpu_pda is used even before pda_init for
that cpu is called (to set the static per-cpu areas offset table etc)
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch enables early intialization of cpu_to_node.
apicid_to_node is built by reading the SRAT table, from acpi_numa_init with
ACPI_NUMA and k8_scan_nodes with K8_NUMA.
x86_cpu_to_apicid is built by parsing the ACPI MADT table, from acpi_boot_init.
We combine these two tables and setup cpu_to_node.
Early intialization helps the static per_cpu_areas in getting pages from
correct node.
Change since last release:
Do not initialize early init_cpu_to_node for faking node cases.
Patch tested on TYAN dual core 4P board with K8 only, ACPI_NUMA.
Tested on EM64T NUMA. Also tested with numa=off, numa=fake, and running
a kernel compiled with NUMA on a regular EM64 2 way SMP.
Signed-off-by: Alok N Kataria <alokk@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Passing random input values in eax to cpuid is not a good idea
because the CPU will GPF for unknown ones.
Use the correct x86-64 version that exists for a longer time too.
This also adds a memory barrier to prevent the optimizer from
reordering.
Cc: tigran@veritas.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The real vsyscall .text addresses are not mapped when the alternative()
replacement runs early, so use some black magic to access them using
the direct mapping.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They already do this in hardware and the Linux algorithm
actually adds errors.
Cc: mingo@elte.hu
Cc: rohit.seth@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Apic id is in most significant 8 bits of APIC_ID register. Current code
is trying to write apic id to least significant 8 bits. This patch fixes
it.
o This fix enables booting uni kdump capture kernel on a cpu with non-zero
apic id.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove exports that are already exported from the object's source file.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
These functions are inlines and shouldn't be exported.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove optimization for old B stepping Opteron
- Make the fast path for copies with a multiple of eight length faster.
- Minor instruction rearrangement to hopefully avoid a pipeline
stall or two.
- Add comment about errata to consider.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
AK: I hacked Muli's original patch a lot and there were a lot
of changes - all bugs are probably to blame on me now.
There were also some changes in the fall back behaviour
for swiotlb - in particular it doesn't try to use GFP_DMA
now anymore. Also all DMA mapping operations use the
same core dma_alloc_coherent code with proper fallbacks now.
And various other changes and cleanups.
Known problems: iommu=force swiotlb=force together breaks
needs more testing.
This patch cleans up x86_64's DMA mapping dispatching code. Right now
we have three possible IOMMU types: AGP GART, swiotlb and nommu, and
in the future we will also have Xen's x86_64 swiotlb and other HW
IOMMUs for x86_64. In order to support all of them cleanly, this
patch:
- introduces a struct dma_mapping_ops with function pointers for each
of the DMA mapping operations of gart (AMD HW IOMMU), swiotlb
(software IOMMU) and nommu (no IOMMU).
- gets rid of:
if (swiotlb)
return swiotlb_xxx();
- PCI_DMA_BUS_IS_PHYS is now checked against the dma_ops being set
This makes swiotlb faster by avoiding double copying in some cases.
Signed-Off-By: Muli Ben-Yehuda <mulix@mulix.org>
Signed-Off-By: Jon D. Mason <jdmason@us.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Broken BIOS on Iwill 8way systems reports these and it causes the bootmem
allocator to crash. Add a sanity check if all the PXMs in the
SRAT table cover all memory as reported by e820. If the sanity
check fails the SRAT is rejected and the code will fall back
to discover the NUMA topology using the K8 northbridge registers
when applicable.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adds a new notifier chain that is called with IDLE_START
when a CPU goes idle and IDLE_END when it goes out of idle.
The context can be idle thread or interrupt context.
Since we cannot rely on MONITOR/MWAIT existing the idle
end check currently has to be done in all interrupt
handlers.
They were originally inspired by the similar s390 implementation.
They have a variety of applications:
- They will be needed for CONFIG_NO_IDLE_HZ
- They can be used for oprofile to fix up the missing time
in idle when performance counters don't tick.
- They can be used for better C state management in ACPI
- They could be used for microstate accounting.
This is just infrastructure so far, no users.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix off by one when checking if the machine has enougn memory to need IOMMU
This caused the IOMMUs to be needlessly enabled for mem=4G
Based on a patch from Jon Mason
Signed-off-by: jdmason@us.ibm.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whenever we see that a CPU is capable of C3 (during ACPI cstate init), we
disable local APIC timer and switch to using a broadcast from external timer
interrupt (IRQ 0).
Patch below adds the code for x86_64.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Whenever we see that a CPU is capable of C3 (during ACPI cstate init), we
disable local APIC timer and switch to using a broadcast from external timer
interrupt (IRQ 0). This is needed because Intel CPUs stop the local
APIC timer in C3. This is currently only enabled for Intel CPUs.
Patch below adds the code for i386 and also the ACPI hunk.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the finer control of local APIC timer. We cannot provide a sub-jiffy
control like this when we use broadcast from external timer in place of
local APIC. Instead of removing this only on systems that may end up using
broadcast from external timer (due to C3), I am going the
"I'm feeling lucky" way to remove this fully. Basically, I am not sure about
usefulness of this code today. Few other architectures also don't seem to
support this today.
If you are using profiling and fine grained control and don't like this going
away in normal case, yell at me right now.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I would like to throw out a suggestion for a possible change in the way that
the debug register traps are handled in do_debug() when the trap occurs
in kernel-mode.
In the x86_64 version of do_debug(), the code will skip around sending
a SIGTRAP to the current task if the trap occurred while in kernel mode.
On the i386-side of things, if the access happens to occur in kernel mode
(say during a read(2) of user's buffer that matches the address of a
debug register trap), then the do_debug() routine for i386 will go ahead
and call send_sigtrap() and send the SIGTRAP signal. The send_sigtrap()
code will also set the info.si_addr to NULL in this case (even though I
don't understand why, since the SIGTRAP siginfo processing doesn't use
the si_addr field...).
So I would like to suggest that the x86_64 do_debug() routine also
follow this type of behavior and have it go ahead and send the
SIGTRAP signal to the current task, even if the debug register trap
happens to have occurred in kernel mode. I have taken a stab at
a patch for this change below. (It includes the i386-ish change
for setting si_addr to NULL when the trap occurred in kernel mode.)
It seems like a useful feature to be able to 'watch' a user location that
might also be modified in the kernel via a system service call, and have the
debugger report that information back to the user, rather than to just
silently ignore the trap.
Additionally, I realize that users that pull in a kernel debugger such as
KGDB into their kernel might want to remove this change below when they add
in KGDB support. However, they could alternatively look at the current
task's thread.debugreg[] values to see if the trap occurred due to KGDB
or instead because of a user-space debugger trap, and still honor the
user SIGTRAP processing (instead of the KGDB breakpoint processing)
if the trap matches up with the thread.debugreg[] registers.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Much better to deal with these than with the magic numbers.
And remove the comment describing the bits - kernel source
is no replacement for an architecture manual.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Don't need to do the vmalloc check for the module range because its
PML4 is shared with the kernel text.
Also removed an unnecessary TLB flush.
Pointed out by Jan Beulich
Cc: jbeulich@novell.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is on the same lines as Zachary Amsden's i386 GDT page alignemnt
patch in -mm, but for x86_64.
Patch to align and pad x86_64 GDT on page boundries.
[AK: some minor cleanups and fixed incorrect TLS initialization
in CPU init.]
Signed-off-by: Nippun Goel <nippung@calsoftinc.com>
Signed-off-by: Ravikiran Thirumalai <kiran@scalex86.org>
Signed-off-by: Shai Fultheim <shai@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This might help on distributions that use a 32bit biarch compiler.
First pass -m64 by default.
Secondly add some more .code32s because at least the Ubuntu biarch
32bit as called by gcc doesn't seem to handle -m64 -m32 as generated
by the Makefile without such assistance.
And finally make sure the linker script can be preprocessed
with a 32bit cpp.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attempt to avoid overflow in __delay caused varying precision
on different CPUs depending on differences in the CPU speed.
We should be able to do this multiplication with out overflowing
provided the
cpu is running at less than about 128 GHz. xloops < 20000 * 0x10c6.
loops_per_jiffy * HZ <= cpu_clock_speed. So if the cpu clock speed
< 2^64/(20000 * 0x10c6) = 2^64/ 51E6CC0 < 2^64/2^27 = 2^37 = 128G we
will not overflow the calculation.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we don't know the node a PCI bus is connected to return -1.
This matches the generic code.
Noticed by Ravikiran G Thirumalai <kiran@scalex86.org>
Cc: Ravikiran G Thirumalai <kiran@scalex86.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of Opteron BIOS just pass 10 in all SLIT entries (10 is the
normalized unit). This is actually worse than the default heuristic
because it leads to pci_distance not knowing the difference between
local and remote nodes anymore. This messes up some NUMA
heuristics in generic code.
In this case it's better to fall back to the default heuristic
which just does nodea == nodeb ? 10 : 20.
This patch does some basic sanity checking on the SLIT and only accepts
the SLIT when it passes.
Invariants enforced are:
- Node to itself shall be 10
- Any other distance shouldn't be 10
- Distances smaller than 10 are illegal
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some people need it now on 64bit so reuse the i386 code for
x86-64. This will be also useful for future bug workarounds.
It is a bit simplified there because there is no need
to do it very early on x86-64. This means it doesn't need
early ioremap et.al. We run it as a core initcall right now.
I hope it's not needed for early setup.
I added a general CONFIG_DMI symbol in case IA64 or someone
else wants to reuse the code later too.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This was a backup file that somehow made it into the official
tree. Never used for anything. Remove.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The introduction of call_softirq switching to the interrupt stack several
releases earlier resulted in a problem with the code in show_trace, which
assumes that it can pick the previous stack pointer from the end of the
interrupt stack.
Cc: Andi Kleen <ak@muc.de>
Cc: Arjan van de Ven <arjanv@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Be more careful with TF handling to fix some copy protection codes in wine
patch originally for i386 by Linus, then ported to x86_64 by Andi Kleen
see: [PATCH] x86_64: Some fixes for single step handling
commit: be61bff789
But it was never applied to the ia32 emulation code which breaks some
copy-protection schemes under wine when running on x86_64.
Signed-off-by: Peter Beutner <p.beutner@gmx.net>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So why are we calling smp_send_stop from machine_halt?
We don't.
Looking more closely at the bug report the problem here
is that halt -p is called which triggers not a halt but
an attempt to power off.
machine_power_off calls machine_shutdown which calls smp_send_stop.
If pm_power_off is set we should never make it out machine_power_off
to the call of do_exit. So pm_power_off must not be set in this case.
When pm_power_off is not set we expect machine_power_off to devolve
into machine_halt.
So how do we fix this?
Playing too much with smp_send_stop is dangerous because it
must also be safe to be called from panic.
It looks like the obviously correct fix is to only call
machine_shutdown when pm_power_off is defined. Doing
that will make Andi's assumption about not scheduling
true and generally simplify what must be supported.
This turns machine_power_off into a noop like machine_halt
when pm_power_off is not defined.
If the expected behavior is that sys_reboot(LINUX_REBOOT_CMD_POWER_OFF)
becomes sys_reboot(LINUX_REBOOT_CMD_HALT) if pm_power_off is NULL
this is not quite a comprehensive fix as we pass a different parameter
to the reboot notifier and we set system_state to a different value
before calling device_shutdown().
Unfortunately any fix more comprehensive I can think of is not
obviously correct. The core problem is that there is no architecture
independent way to detect if machine_power will become a noop, without
calling it.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I noticed that some lowlevel send_IPI_mask helpers had a hotplug/preempt
race whereupon the cpu_online_map was read before disabling preemption;
...
cpumask_t mask = cpu_online_map;
int cpu = get_cpu();
cpu_clear(cpu, mask);
...
But then i realised that there is no need for these lowlevel functions to
be going through all this trouble when all the callers are already made
hotplug/preempt safe.
Signed-off-by: Zwane Mwaikambo <zwane@arm.linux.org.uk>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is one CPU here whose MCE bank count is 6. This patch increases
x86_64's MCE bank count.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following is probably a good idea given that the atomic_set() isn't
a barrier here either.
Signed-off-by: Benjamin LaHaise <benjamin.c.lahaise@intel.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This
- switches the INT3 handler to run on an IST stack (to cope with
breakpoints set by a kernel debugger on places where the kernel's
%gs base hasn't been set up, yet); the IST stack used is shared with
the INT1 handler's
[AK: this also allows setting a kprobe on the interrupt/exception entry
points]
- allows nesting of INT1/INT3 handlers so that one can, with a kernel
debugger, debug (at least) the user-mode portions of the INT1/INT3
handling; the nesting isn't actively enabled here since a kernel-
debugger-free kernel doesn't need it
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Print bits for RDTSCP, SVM, CR8-LEGACY.
Also now print power flags on i386 like x86-64 always did.
This will add a new line in the 386 cpuinfo, but that shouldn't
be an issue - did that in the past too and I haven't heard
of any breakage.
I shrunk some of the fields in the i386 cpuinfo_x86 to chars
to make up for the new int "x86_power" field. Overall it's
smaller than before.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
They previously tried to figure this out on their own.
Suggested by Venkatesh.
Cc: venkatesh.pallipadi@intel.com
Cc: davej@redhat.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Define it for i386 too.
This is a synthetic flag that signifies that the CPU's TSC runs
at a constant P state invariant frequency.
Fix up the logic on x86-64/i386 to set it on all known CPUs.
Use the AMD defined bit to set it on future AMD CPUs.
Cc: venkatesh.pallipadi@intel.com
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Was only used by the floppy driver to work around some ancient
hardware bug that should never occur on any 64bit system.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Most users don't need it so no need to waste memory.
This means an user has to specify the appropiate number of
hotplug CPUs on the command line with additional_cpus=...
or fix their BIOS to follow the convention in
Documentation/x86-64/cpu-hotplug-spec
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Adjust page fault protection error check before considering it to be
a vmalloc synchronization candidate.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make sure no iret can fault without attached recovery code.
Cannot happen in the normal case, but might be useful
with kernel debuggers
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since a double fault always implies that kernel data structures are
corrupt, this fault should neither be handed to user mode handling,
nor should the handler allow resuming the faulting code stream (since
architecturally this isn't a fault, but an abort).
Note that this slightly depends on the previously submitted patch
adjusting the prototype of notify_die() (a compiler warning will result
without that other patch).
AK: Removed obsolete CONFIG_CHECKING code, added comments
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This adjusts things so that handlers of the die() notifier will have
sufficient information about the trap currently being handled. It also
adjusts the notify_die() prototype to (again) match that of i386.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Other than apparently commonly assumed, the bound instruction does not
require the corresponding IDT entry to have DPL 3.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
As a follow-up to the introduction of CONFIG_UNWIND_INFO, this
separates the generation of frame unwind information for x86-64 from
that of full debug information.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Based on the documentation recently posted by Richard Brunner.
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Frame unwind information was still incorrect for ia32_ptregs_common
(sorry, my fault), and could be improved for some of the other entry
points.
Signed-Off-By: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch: Use <linux/capability.h> where capable() is used.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There is a window where a probe gets removed right after the probe is hit
on some different cpu. In this case probe handlers can't find a matching
probe instance related to break address. In this case we need to read the
original instruction at break address to see if that is not a break/int3
instruction and recover safely.
Previous code had a bug where we were not checking for the above race in
case of reentrant probes and the below patch fixes this race.
Tested on IA64, Powerpc, x86_64.
Signed-off-by: Anil S Keshavamurthy <anil.s.keshavamurthy@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The HDIO_GETGEO patch left an unused variable in the UML block driver. This
gets rid of it.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The debug-stub patch was broken on x86_64 because it thinks the frame size
there is 168 words. In reality, it is 168 bytes, and using HOST_FRAME_SIZE,
which is expressed in consistent units across architectures, fixes this.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
CON_PRINTBUFFER was a bad idea for the mconsole console. It causes the boot
output to be printed twice.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Undo the previous no-modes patch since Adrian Bunk sent in a kbuild way of
doing the same thing.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The MODE_TT help was a little outdated. This updates it in light of the
existence of skas0 mode. It's also turned off by default since it is mostly
obsoleted by skas0 mode.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2.6.15-mm1 caused kernel-offsets.c to stop compiling with a syntax error in a
header. The problem was with KBUILD_BASENAME, which didn't get a definition
with the by-hand compilation in the main UML Makefile.
This was OK before since the expansion was syntactically the same as the
KBUILD_BASENAME token. With -mm1, the expansion is now a quote-delimited
string, so there needs to be a definition of it.
Since kernel-offsets.c is basically the same as other arches' asm-offsets.c,
and those seem to build OK, this patch turns kernel-offsets.c into
asm-offsets.c. kernel-offsets.c is in arch/um/sys-$(SUBARCH), i.e. sys-i386
and sys-x86_64, while kbuild expects it to be in arch/um/kernel.
kernel-offsets.c is moved to
arch/um/include/sysdep-$(SUBARCH)/kernel-offsets.h, which is included by
arch/um/kernel/asm-offsets.c. With that, include/asm-um/asm-offsets.h is
generated automatically. kernel-offsets.h continues to exist because it needs
to be accessible to userspace UML code, and include/asm-um isn't. So, a
symlink is made from arch/um/include/kernel-offsets.h to
include/asm-um/asm-offsets.h.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes a typo in the dependencies of HUGETLB_PAGE_SIZE_64K.
It might be more logical to rename the HUGETLB_PAGE_SIZE_*K
dependencies to HUGETLB_PAGE_SIZE_*KB, but let's fix this bug first.
This bug was reported by Jean-Luc Leger <reiga@dspnet.fr.eu.org>.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let's switch mutex_debug_check_no_locks_freed() to take (addr, len) as
arguments instead, since all its callers were just calculating the 'to'
address for themselves anyway... (and sometimes doing so badly).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
arch/powerpc/kernel/crash.c isn't safe for PPC32 (yet?), so don't build it.
Built with CONFIG_KEXEC=y for pmac32_defconfig, pseries_defconfig,
and g5_defconfig.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
clean-files was being set twice rather than being appended to.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Removing the dependency on the boot image build was good, but it also
meant that the $< expansion by make needed to be done explicitly.
Noted by Stephen Hemminger.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
iSeries doesn't need to set the htab_address explicitly, htab_initialize()
will do it for us later.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
To make iSeries just a teensy bit less special, create ibm,pft-size properties
in the iSeries device tree. We can then rely on htab_dt_scan_pftsize() to set
ppc64_pft_size for us.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated Kconfig & Makefiles in prep for adding support for the Freescale
MPC83xx family of processors to arch/powerpc. Moved around some config
options that are more globally applicable to other PowerPC processors.
Added a temporary config option (83xx) to match existing arch/ppc support
for the MPC83xx line.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The SPE Book IV indicates that MFC DMA operations must be
suspended and restored on SPU context switch (in Step 8).
This patch adds that operation, which is missing from the
current spufs implementation.
Signed-off-by: Masato Noguchi <Masato.Noguchi@jp.sony.com>
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Acked-by: Arnd Bergmann <arndb@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the compilation error (shown below) when CONFIG_SMP=n.
arch/powerpc/kernel/crash.c: In function `crash_kexec_prepare_cpus':
arch/powerpc/kernel/crash.c:236: error: implicit declaration of
function `smp_release_cpus'
Signed-off-by: Haren Myneni <haren@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The current ppc64 per cpu data implementation is quite slow. eg:
lhz 11,18(13) /* smp_processor_id() */
ld 9,.LC63-.LCTOC1(30) /* per_cpu__variable_name */
ld 8,.LC61-.LCTOC1(30) /* __per_cpu_offset */
sldi 11,11,3 /* form index into __per_cpu_offset */
mr 10,9
ldx 9,11,8 /* __per_cpu_offset[smp_processor_id()] */
ldx 0,10,9 /* load per cpu data */
5 loads for something that is supposed to be fast, pretty awful. One
reason for the large number of loads is that we have to synthesize 2
64bit constants (per_cpu__variable_name and __per_cpu_offset).
By putting __per_cpu_offset into the paca we can avoid the 2 loads
associated with it:
ld 11,56(13) /* paca->data_offset */
ld 9,.LC59-.LCTOC1(30) /* per_cpu__variable_name */
ldx 0,9,11 /* load per cpu data
Longer term we can should be able to do even better than 3 loads.
If per_cpu__variable_name wasnt a 64bit constant and paca->data_offset
was in a register we could cut it down to one load. A suggestion from
Rusty is to use gcc's __thread extension here. In order to do this we
would need to free up r13 (the __thread register and where the paca
currently is). So far Ive had a few unsuccessful attempts at doing that :)
The patch also allocates per cpu memory node local on NUMA machines.
This patch from Rusty has been sitting in my queue _forever_ but stalled
when I hit the compiler bug. Sorry about that.
Finally I also only allocate per cpu data for possible cpus, which comes
straight out of the x86-64 port. On a pseries kernel (with NR_CPUS == 128)
and 4 possible cpus we see some nice gains:
total used free shared buffers cached
Mem: 4012228 212860 3799368 0 0 162424
total used free shared buffers cached
Mem: 4016200 212984 3803216 0 0 162424
A saving of 3.75MB. Quite nice for smaller machines. Note: we now have
to be careful of per cpu users that touch data for !possible cpus.
At this stage it might be worth making the NUMA and possible cpu
optimisations generic, but per cpu init is done so early we have to be
careful that all architectures have their possible map setup correctly.
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds Kconfig entries to control the early debugging options,
currently in setup_64.c.
Doing this via Kconfig rather than #defines means you can have one source tree,
which is buildable for multiple platforms - and you can enable the correct
early debug option for each platform via .config.
I made udbg_early_init() a static inline because otherwise GCC is to daft to
optimise it away when debugging is off.
Now that we have udbg_init_rtas() we can make call_rtas_display_status* static.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Connect iSeries up to the standard early debugging infrastructure.
To actually use this you need to enable the iSeries early debugging
in setup_64.c. Then after the messages are logged hit Ctrl-x Ctrl-x on
your console to dump the Hypervisor console buffer.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The RPAPHP hoplug driver will not build as a module, because it calls
on a pcibios routine which is not exported. This exports the symbol.
Problem reported by Olaf Hering <olh@suse.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Cleanup vmlinux.lds.S by using STABS_DEBUG macro from vmlinux.lds.h
instead of repeating the sections.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fix Dino reporting on J2240. This particular machine thought it
had a Cujo. Also add J2240 Dino chip to the hp_hardware_list.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
max_low_pfn was not being set in arch/parisc/mm/init.c, causing severe
problems whenever anything tried to use BLK_BOUNCE_HIGH. Set it to
max_pfn like other similar architectures do.
Signed-off-by: Grant Grundler <grundler@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make knapps work with its 64MB gfx card. I probably just broke another
machine in the process, but assuming 64MB when 64MB aligned is probably
safer than assuming 32MB all the time.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Fixup ioremap a bit. It seems to work on 32-bit kernels, but fails
miserably on the first ioremapped access on 64-bit kernels. Also, having
STI enabled causes it to fail. Probably because we're passing an ioremapped
region to a real-mode STI call...
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Make flush_data_cache_local, flush_instruction_cache_local and
flush_tlb_all_local take a void * so they don't have to be cast
when using on_each_cpu(). This becomes a problem when on_each_cpu
is a macro (as it is in current -mm).
Also move the prototype of flush_tlb_all_local into tlbflush.h and
remove its declaration from .c files.
Signed-off-by: Matthew Wilcox <willy@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
Flag a whole bunch of things as __read_mostly on parisc. Also flag a few
branches as unlikely() and cleanup a bit of code.
Signed-off-by: Helge Deller <deller@parisc-linux.org>
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
