MTD internal API presently uses 32-bit values to represent
device size. This patch updates them to 64-bits but leaves
the external API unchanged. Extending the external API
is a separate issue for several reasons. First, no one
needs it at the moment. Secondly, whether the implementation
is done with IOCTLs, sysfs or both is still debated. Thirdly
external API changes require the internal API to be accepted
first.
Note that although the MTD API will be able to support 64-bit
device sizes, existing drivers do not and are not required
to do so, although NAND base has been updated.
In general, changing from 32-bit to 64-bit values cause little
or no changes to the majority of the code with the following
exceptions:
- printk message formats
- division and modulus of 64-bit values
- NAND base support
- 32-bit local variables used by mtdpart and mtdconcat
- naughtily assuming one structure maps to another
in MEMERASE ioctl
Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com>
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The patch fixes CFI issue with multipartitional devices leading to the
set of errors or even deadlock. The problem is CFI FL_SYNCING state race
with flash operations (e.g. erase suspend). It is reproduced by running
intensive writes on one JFFS2 partition and simultaneously performing
mount/unmount cycle on another partition of the same chip.
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Timeouts are currently given by the typical operation time times 8.
It works in the general well-behaved case but not when an erase block is
failing. For erase operations, it seems that a failing erase block will
keep the device state machine in erasing state until the vendor
specified maximum timeout period has passed. By this time the driver
would have long since timed out, left erasing state and attempted
further operations which all fail. This patch implements timeouts using
values from the CFI Query structure when available.
The patch also sets a longer timeout for locking operations. The current
value used for locking/unlocking given by 1000000/HZ microseconds is too
short for devices like J3 and J5 Strataflash which have a typical clear
lock-bits time of 0.5 seconds.
Signed-off-by: Anders Grafström <grfstrm@users.sourceforge.net>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
The kernel.h macro DIV_ROUND_UP performs the computation (((n) + (d) - 1) /
(d)) but is perhaps more readable.
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Existing CFI driver has problems with excessive writes during erase.
If CFI driver does many writes during one erase cycle we may face the
messages with -ETIMEO error on erase operation. It may cause the
following data corruption and kernel panics.
The reason of the issue is related to specifics of suspend operation:
if we write to flash during erase, suspend operation will cost some time
to erase procedure (for P30 it could be significant). In current version of
cfi driver the problem of many suspends is partially workarounded by adding
some time reserv to any operation (8xerase_time) but if we have many writes
during one erase the problem appears.
This patch detects the suspend and resets timer if suspend occured. It
has been well verified on different chips. No problems were found.
Could you please include the patch as it is simple and fixes bad issue.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Once upon a time, the MTD repository was using CVS.
This patch therefore removes all usages of the no longer updated CVS
keywords from the MTD code.
This also includes code that printed them to the user.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Add support for M50FLW080A and M50FLW080B revisions of LPC flash
devices.
Signed-off-by: Aaron Lindner <alindner@xes-inc.com>
Signed-off-by: Nate Case <ncase@xes-inc.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix typo in erase suspend while write fixup code leading to compile time
error if CMDSET0001_DISABLE_ERASE_SUSPEND_ON_WRITE was defined.
drivers/mtd/chips/cfi_cmdset_0001.c: In function 'fixup_intel_strataflash':
drivers/mtd/chips/cfi_cmdset_0001.c:212: error: 'struct cfi_pri_amdstd' has no member named 'SuspendCmdSupport'
Signed-off-by: Alexander Belyakov <abelyako@googlemail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Adding the ability to get a physical address from point() in addition
to virtual address. This physical address is required for XIP of
userspace code from flash.
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Reviewed-by: Jörn Engel <joern@logfs.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
collie seems to contain LH28F640BF flash chips. According to
http://sharp-world.com/products/device/flash/pdf/*FUM00701*@E.pdf
(page 83) if they have 0x51 of Extended Query Table (number of hardware
partitions) set to zero, they have a single fixed partition.
This patch makes those chips work.
Signed-off-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Untested, but shouldn't break anything... Makes MTD_XIP arch
independent. I guess this is why xip_iprefetch() was made for.
Signed-off-by: Paulius Zaleckas <paulius.zaleckas@teltonika.lt>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
THe CFI driver in 2.6.24 kernel is broken. Not so intensive read/write
operations cause incomplete writes which lead to kernel panics in JFFS2.
We investigated the issue - it is caused by bug in FL_SHUTDOWN parsing code.
Sometimes chip returns -EIO as if it is in FL_SHUTDOWN state when it should
wait in FL_PONT (error in order of conditions).
The following patch fixes the bug in state parsing code of CFI. Also I've
added comments to notify developers if they want to add new case in future.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Reviewed-by: Joern Engel <joern@logfs.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Patch for unlocking all Intel flash that has instant locking on power up.
The patch has been tested on Intel M18, P30 and J3D Strata Flash.
1. The automatic unlocking can be disabled for a particular partition
in the map or the command line.
a. For the bit mask in the map it should look like:
.mask_flags = MTD_POWERUP_LOCK,
b. For the command line parsing it should look like:
mtdparts=0x80000(bootloader)lk
2. This will only unlock parts with instant individual block locking.
Intel parts with legacy unlocking will not be unlocked.
Signed-off-by: Justin Treon <justin_treon@yahoo.com>
Signed-off-by: Jared Hulbert <jaredeh@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The bug causes corruptions of data read from flash.
The original code performs cache invalidation from "adr" to "adr + len"
in do_write_buffer(). Since len and adr could be updated in the code
before invalidation - it causes improper setting of cache invalidation
regions.
Signed-off-by: Massimo Cirillo <maxcir@gmail.com>
Signed-off-by: Giuseppe D'Eliseo <giuseppedeliseo@gmail.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Acked-by: Jörn Engel <joern@logfs.org>
Signed-off-by: David Woohouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
while running stress tests we have met cfi_cmdset_0001.c driver issue.
Working on multipartitional devices with erase suspend on write
feature enabled it is possible to get erase operation invoked on chip
with suspended erase. get_chip() looses information about earlier
suspended erase and new erase operation gets issued. New erase
operations report successful completion, but blocks remain dirty
causing, for example, JFFS2 error messages like:
...
Newly-erased block contained word 0x20031985 at offset 0x00200000
Newly-erased block contained word 0x20031985 at offset 0x00280000
Newly-erased block contained word 0x20031985 at offset 0x00240000
...
The patch below fixes that issue.
Signed-off-by: Alexander Belyakov <alexander.belyakov@intel.com>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Convert CFI tables from Atmel cmdset_0001 chips to Intel format and set
BufWrite timeouts to 0 for Atmel cmdset_0001 and cmdset_0002 chips.
Some chips may indicate support for buffered writes even though they
only support dual-word writes.
The CFI fixup must run before fixup_use_write_buffers for this to work.
Signed-off-by: Håvard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This patch solves kernel deadlock issue seen on JFFF2 simultaneous
operations. Detailed investigation of the issue showed that the kernel
deadlock is caused by tons of recursive get_chip calls.
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Acked-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we press ctrl-alt-del,kernel_restart_prepare will invoke
cfi_intelext_reboot which will set flash to read array mode, but later
when device_shutdown is invoked which may put current work queue to
sleep and other process may be scheduled to running and programming
flash in not FL_READY mode again. So we can't boot up if this flash is
used for bootloader.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The CFI probe routine is capable of detecting flash banks consisting of
identical chips mapped to physically discontiguous addresses. (One
common way this can occur is if a flash bank is populated with chips of
less capacity than the hardware was designed to support.) The CFI
point() routine currently ignores any such gaps. This patch fixes
the CFI point() routine so that it truncates any request that would
span a gap.
Signed-off-by: Andy Lowe <alowe@mvista.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Trivial fix of a spelling error in a comment in cfi_cmdset_0001.c
s/ships/chips/
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Use NULL instead of 0 for pointer:
drivers/mtd/chips/cfi_cmdset_0001.c:2258:43: warning: Using plain integer as NULL pointer
Other changes by inspection.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix sparse warnings generated from cfi_cmdset_0001.c.
drivers/mtd/chips/cfi_cmdset_0001.c:1783:5: warning: symbol 'cfi_intelext_erase_varsize' was not declared. Should it be static?
drivers/mtd/chips/cfi_cmdset_0001.c:2258:43: warning: Using plain integer as NULL pointer
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Auto unlock sectors on resume for auto locking flash on power up.
Signed-off-by: Rodolfo Giometti <giometti@enneenne.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Remove ugly and weird MTD_PROGREGION_CTRLMODE_VALID() and
MTD_PROGREGION_CTRLMODE_INVALID() macros. There is only one
user of them and they are used locally just for printing.
Anyway, this patch is a preparation for removing mtd->ecctype
and mtd->eccsize, but these macros use them. Fix this.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
In commit c172471b78 Nico switched to using
common code for polling for command completion. Unfortunately he also used
a common default timeout for both write and erase commands, despite the
fact that erases can take a _whole_ lot longer. Use a more sensible
default for erase timeout.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
When we sleep and wait for a suspended operation to be resumed, go
back and check until it's ready -- don't just continue after the first
time we're woken. This can cause file system corruption.
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During some testing with several samsung s3c24xx based
devices it was discovered that often the
cfi_cmdset_0001.c would not leave the chip in
read-array mode on suspend. this is an issue if the
same flash chip is used for the bootloader that needs
to be read on resume.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix of performance and stability issues on Intel NOR chips. It fixes:
1. Very low write performance on Sibley (perf tests demonstrated write
performance less than 100Kb/sec when it should be over 400Kb/sec).
2. Low erase performance. (perf tests on Sibleuy demonstrated erase
performance 246Kb/sec when it should be over 300Kb/sec).
3. Error on JFFS2 tests with CPU loading application when MTD returns
"block erase error: (status timeout)" To fix the issue it does the
following:
1. Removes the timeout tuning from inval_cache_and_wait_for_operation.
2. Waiting conditions in inval_cache_and_wait_for_operation now is
based on timer resolution
If timeout is lower than timer resolution then we do in cycle
"Checking the status"
udelay(1);
cond_resched();
If timeout is greater than timer resolution (probably erase
operation) We do the following
sleep for half of operation timeout and do in cycle the following
"Checking the status"
sleep for timer resolution
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Alexey Korolev <akorolev@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
o Add a flag MTD_BIT_WRITEABLE for devices that allow single bits to be
cleared.
o Replace MTD_PROGRAM_REGIONS with a cleared MTD_BIT_WRITEABLE flag for
STMicro and Intel Sibley flashes with internal ECC. Those flashes
disallow clearing of single bits, unlike regular NOR flashes, so the
new flag models their behaviour better.
o Remove MTD_ECC. After the STMicro/Sibley merge, this flag is only set
and never checked.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
At least two flashes exists that have the concept of a minimum write unit,
similar to NAND pages, but no other NAND characteristics. Therefore, rename
the minimum write unit to "writesize" for all flashes, including NAND.
Signed-off-by: Joern Engel <joern@wh.fh-wedel.de>
This allows for much better abstraction and separation of the XIP and
non-XIP cases with their own specific implementations. This fixes the
case where a timeout was tripped on in the XIP case by the code that
was meant for the non-XIP case only.
This also makes for a nice code reduction.
Signed-off-by: Nicolas Pitre <nico@cam.org>
CC: "Alexey, Korolev" <alexey.korolev@intel.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
The patch below fixes a potential starvation issue that can arise when
there is contention on a chip during a period when a process is
currently writing to it. The starvation is avoided by conditionally
rescheduling when the chip is left in a state usable by other processes.
Signed-off-by: Josh Boyer <jdub@us.ibm.com>
Signed-off-by: Tom Gall <tom_gall@vnet.ibm.com>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Fix a kernel oops for Intel P30 flashes, where the wait queue head was not
initialized for the flchip struct, which in turn caused a crash at the
first read operation.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I found an issue in cfi_cmdset0001.c. It is related to cache region
invalidation in the buffered write procedure.
The code performs cache invalidation from "cmd_addr" to "cmd_adr + len" in
do_write_buffer() while we modify region from "adr" to "adr+len".
This issue affects writes + reads of data by small chunks.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is the drivers/mtd part of the big kfree cleanup patch.
Remove pointless checks for NULL prior to calling kfree() in drivers/mtd/.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Acked-by: Joern Engel <joern@wohnheim.fh-wedel.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change to the extended cfi table parsing for Intel NOR flash that uses
the info in the extended table to 'walk' the table rather than using
hard coding for various primary extended query table version numbers.
From: Jared Hulbert <jaredeh@gmail.com>
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While this might be useful for all supported flash types, it is mandatory
for proper JFFS2 support with Sibley flash.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This updates the Primary Vendor-Specific Extended Query parsing to
version 1.4 in order to get the information about the Configurable
Programming Mode regions implemented in the Sibley flash, as well as
selecting the appropriate write command code.
This flash does not behave like traditional NOR flash when writing data.
While mtdblock should just work, further changes are needed for JFFS2 use.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
