This patch adds the necessary core bus support used by device drivers
that sit on the IBM GX bus on modern pSeries machines like the Galaxy
infiniband for example. It provide transparent DMA ops (the low level
driver works with virtual addresses directly) along with a simple bus
layer using the Open Firmware matching routines.
Signed-off-by: Heiko J Schick <schickhj@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This cleanup patch speeds up the null syscall path on ppc64 by about 3%,
and brings the ppc32 and ppc64 code slightly closer together.
The ppc64 code was checking current_thread_info()->flags twice in the
syscall exit path; once for TIF_SYSCALL_T_OR_A before disabling
interrupts, and then again for TIF_SIGPENDING|TIF_NEED_RESCHED etc after
disabling interrupts. Now we do the same as ppc32 -- check the flags
only once in the fast path, and re-enable interrupts if necessary in the
ptrace case.
The patch abolishes the 'syscall_noerror' member of struct thread_info
and replaces it with a TIF_NOERROR bit in the flags, which is handled in
the slow path. This shortens the syscall entry code, which no longer
needs to clear syscall_noerror.
The patch adds a TIF_SAVE_NVGPRS flag which causes the syscall exit slow
path to save the non-volatile GPRs into a signal frame. This removes the
need for the assembly wrappers around sys_sigsuspend(),
sys_rt_sigsuspend(), et al which existed solely to save those registers
in advance. It also means I don't have to add new wrappers for ppoll()
and pselect(), which is what I was supposed to be doing when I got
distracted into this...
Finally, it unifies the ppc64 and ppc32 methods of handling syscall exit
directly into a signal handler (as required by sigsuspend et al) by
introducing a TIF_RESTOREALL flag which causes _all_ the registers to be
reloaded from the pt_regs by taking the ret_from_exception path, instead
of the normal syscall exit path which stomps on the callee-saved GPRs.
It appears to pass an LTP test run on ppc64, and passes basic testing on
ppc32 too. Brief tests of ptrace functionality with strace and gdb also
appear OK. I wouldn't send it to Linus for 2.6.15 just yet though :)
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Moved 83xx and QUICC Engine interrupt handling code into arch/powerpc
as a precursor of getting 83xx sub-arch building in arch/powerpc.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch merges, to some extent, the PPC32 and PPC64 kexec implementations.
We adopt the PPC32 approach of having ppc_md callbacks for the kexec functions.
The current PPC64 implementation becomes the "default" implementation for PPC64
which platforms can select if they need no special treatment.
I've added these default callbacks to pseries/maple/cell/powermac, this means
iSeries no longer supports kexec - but it never worked anyway.
I've renamed PPC32's machine_kexec_simple to default_machine_kexec, inline with
PPC64. Judging by the comments it might be better named machine_kexec_non_of,
or something, but at the moment it's the only implementation for PPC32 so it's
the "default".
Kexec requires machine_shutdown(), which is in machine_kexec.c on PPC32, but we
already have in setup-common.c on powerpc. All this does is call
ppc_md.nvram_sync, which only powermac implements, so instead make
machine_shutdown a ppc_md member and have it call core99_nvram_sync directly
on powermac.
I've also stuck relocate_kernel.S into misc_32.S for powerpc.
Built for ARCH=ppc, and 32 & 64 bit ARCH=powerpc, with KEXEC=y/n. Booted on
P5 LPAR and successfully kexec'ed.
Should apply on top of 493f25ef40.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch removes the EXPORT_SYMBOL'ed but completely unused variable
ucSystemType and removes the unneeded EXPORT_SYMBOL(_prep_type).
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Acked-by: Tom Rini <trini@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the ARM AMBA bus is used on MIPS as well as ARM, we need
to make the bus available for other architectures to use. Move
the AMBA include files from include/asm-arm/hardware/ to
include/linux/amba/
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Richard Purdie
Fix a gcc4 build error (incomplete element type) in the pxa SharpSL
PM code.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Many arches make shared objects for VDSOs. Generally exclude them.
Signed-off-by: Brian Gerst <bgerst@didntduck.org>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
This was harmless, but for the case of a device that had no irq
pre-defined we would incorrectly suggest that "usepirqmask" might make a
difference. It never would, and the message was just confusing people.
Reported in the dmesg of Etienne Lorrain.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Sanitize some s390 Kconfig options. We have ARCH_S390, ARCH_S390X,
ARCH_S390_31, 64BIT, S390_SUPPORT and COMPAT. Replace these 6 options by
S390, 64BIT and COMPAT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
New feature V=V qdio pass-through.
QDIO and HiperSockets processing in z/VM V=V guest environments (as well as
V=R with z/VM running in LPAR mode) requires shadowing of all QDIO
architecture queue elements. Especially the shadowing of SBALs and SLSBs
structures in the hypervisor, and the need to issue SIGA SYNC operations to
observe state changes, eventually causes significant CPU processing overhead
in the hypervisor.
The QDIO pass-through support for V=V guests avoids the shadowing of SBALs and
SLSBs. This significantly reduces the hypervisor overhead for QDIO based I/O.
Signed-off-by: Frank Pavlic <pavlic@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the hardware accelerated AES crypto algorithm.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add support for the hardware accelerated sha256 crypto algorithm.
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all references to z990 by s390 in the in-kernel crypto files in
arch/s390/crypto. The code is not specific to a particular machine (z990) but
to the s390 platform. Big diff, does nothing..
Signed-off-by: Jan Glauber <jan.glauber@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are some more places where the use of cputime_t instead of an integer
type and the associated macros is necessary for the virtual cputime accounting
on s390. Affected are the s390 specific appldata code and BSD process
accounting.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Check return code of do_sigaltstack and force a SIGSEGV if it is -EFAULT.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert __access_ok to an inline C function and change __get_user primitive to
avoid uaccess compiler warnings.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Hugh Dickins <hugh@veritas.com>
Fix the broken atomic_cmpxchg primitive. Add atomic_sub_and_test,
atomic64_sub_return, atomic64_sub_and_test, atomic64_cmpxchg,
atomic64_add_unless and atomic64_inc_not_zero. Replace old style
atomic_compare_and_swap by atomic_cmpxchg. Shorten the whole header by
defining most primitives with the two inline functions atomic_add_return and
atomic_sub_return.
In addition this patch contains the s390 related fixes of Hugh's "mm: fill
arch atomic64 gaps" patch.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Free the network IRQ when closing down the network devices at shutdown.
Delete the device from the opened devices list on close.
These prevent an -EBADF when later disabling SIGIO on all extant descriptors
and a complaint from free_irq about freeing the IRQ twice.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix up some bogus spacing in the mconsole driver. Also delete the
emacs formatting comment at the end.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass sysrq output back to the mconsole client using the mechanism
introduced for stack output.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The stack command now sends the printk output back to the mconsole client.
This is done by registering a special console for the mconsole driver. This
receives all printk output. Normally, it is ignored, but when a stack command
is issued, any printk output will be sent back to the client.
This will capture any printk output, whether it is stack output or not, since
we can't tell the difference.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is needed for the console output patch, since we have a possibly
non-NULL-terminated string there. So, the new interface takes a string and a
length, and the old interface calls strlen on its string and calls the new
interface with the length.
There's also a bit of whitespace cleanup.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Produce a compile-time error if both MODE_SKAS and MODE_TT are disabled.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Code cleanup - unregister_winch and winch_cleanup had some duplicate code.
This is now abstracted out into free_winch.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch cleans up the umid code:
- The only_if_set argument to get_umid is gone.
- get_umid returns an empty string rather than NULL if there is no umid.
- umid_is_random is gone since its users went away.
- Some printfs were turned into printks because the code runs late enough
that printk is working.
- Error paths were cleaned up.
- Some functions now return an error and let the caller print the error
message rather than printing it themselves. This eliminates the practice of
passing a pointer to printf or printk in, depending on where in the boot
process we are.
- Major tidying of not_dead_yet - mostly error path cleanup, plus a comment
explaining why it doesn't react to errors the way you might expect.
- Calls to os_* interfaces that were moved under os are changed back to
their native libc forms.
- snprintf, strlcpy, and their bounds-checking friends are used more often,
replacing by-hand bounds checking in some places.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
I reworked Gennady's umid OS abstraction patch because the code shouldn't
be moved entirely to os. As it turns out, I moved most of it anyway. This
patch is the minimal one needed to move the code and have it work.
It turns out that the concept of the umid is OS-independent, but
almost everything else about the implementation is OS-dependent.
This is code movement without cleanup - a follow-on patch tidies
everything up without shuffling code around.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for throttling and unthrottling input when the tty
driver can't handle it.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When the tty flip_buf is full, it's a good idea to delay the input processing
for a jiffy, rather than just scheduling the tasklet immediately.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch simplifies the opening and closing of host console devices and the
registration and deregistration of IRQs. The intent is to make it obvious
that an IRQ can't exist without an open file descriptor.
chan_enable will now open the channel, and when both opening and IRQ
registration are desired, this should be used. Opening only is done for the
initial console, so that interface still needs to exist.
The free_irqs_later interface is now gone. It was intended to avoid freeing
an IRQ while it was being processed. It did this, but it didn't eliminate the
possiblity of free_irq being called from an interrupt, which is bad. In its
place is a list of irqs to be freed, which is processed by the signal handler
just before exiting. close_one_chan now disables irqs.
When a host device disappears, it is just closed, and that disables IRQs.
The device id registered with the IRQ is now the chan structure, not the tty.
This is because the interrupt arrives on a descriptor associated with the
channel. This caused equivalent changes in the arguments to line_timer_cb.
line_disable is gone since it is not used any more.
The count field in the line structure is gone. tty->count is used instead.
The complicated logic in sigio_handler with freeing IRQs when necessary and
making sure its idea of the next irq is correct is now much simpler. The irq
list can't be rearranged underneath it, so it is now a simple list walk.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch changes when console devices are configured in order to prepare the
ground for the next patch.
parse_chan_pair is now done earlier, when initcalls are run, rather than when
the device is opened.
When a host device disappears, the channel list is closed, but not freed.
This is required by the previous change. line_config now takes the options
structure as an argument, and line_open doesn't.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
line_setup is changed to return the device which it set up, rather than just
success or failure. This will be important in the line-config patch.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some structure fields were being dynamically initialized when they could be
initialized at compile-time instead. This also makes some declarations static
(in the C sense).
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A bit of restructuring which eliminates the all_allowed argument (which is
mconsole-specific) to line_setup. That logic is moved to the mconsole
callback.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This removes a structure field which turned out to be pointless, and
references to it.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch replaces instances of "sizeof(foo)/sizeof(foo[0])" with
ARRAY_SIZE(foo), which expands to the same thing.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes a bunch of non-functional changes -
return(foo); becomes return foo;
some statements are broken across lines for readability
some trailing whitespace is cleaned up
open_one_chan took four arguments, three of which could be
deduced from the first. Accordingly, they were eliminated.
some examples of "} else {" had a newline added
some whitespace cleanup in the indentation
lines_init got some control flow cleanup
some long lines were broken
removed another emacs-specific C formatting comment
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There are a few functions which are declared to return something, but don't.
These are actually infinite loops which are forced to be declared as non-void.
This makes them all return 0.
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
There were a bunch of calls to uml_strdup dating from before kstrdup was
introduced. This changes those calls. It doesn't eliminate the definition
since there is still a couple of calls in userspace code (which should
probably call the libc strdup).
Signed-off-by: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Doesn't make much sense and unused.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Mikael Starvik <starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
mach_enable_irq/mach_disable_irq are never actually set, so let's remove
them.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch fixes cache memory parameter setting for the M32104 target. So
far, its performance seemed to have been degraded due to incorrect cache
parameter setting.
* arch/m32r/boot/setup.S: Set SFR(Special Fuction Registers) region
to be non-cachable explicitly.
* arch/m32r/mm/cache.c: Fix cache flushing routines not to switch off
the M32104 cache.
Signed-off-by: Hayato Fujiwara <fujiwara@linux-m32r.org>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Modify _port2addr*() routines in arch/m32r/kernel/io_*.c to use
NONCACHE_OFFSET instead of hard-coding of a constant address.
This modification is also required to support an M3A-ZA36 FPGA eva board in
case an MMU-less synthesizable m32r core is used.
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch is for supporting a new target platform, Renesas M32104UT
evaluation board.
The M32104UT is an eval board based on an uT-Engine specification. This board
has an MMU-less M32R family processor, M32104.
http://www-wa0.personal-media.co.jp/pmc/archive/te/te_m32104_e.pdf
This board is one of the most popular M32R platform, so we have ported
Linux/M32R to it.
Signed-off-by: Naoto Sugai <Sugai.Naoto@ak.MitsubishiElectric.co.jp>
Signed-off-by: Hirokazu Takata <takata@linux-m32r.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Kconfig tweaks and tons of deletions.
Signed-off-by: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Richard Henderson <rth@twiddle.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With physical CPU hotplug, the CPU is hot removed and it should not receive
any interrupts. Disabling interrupt is much safer. This basically is what we
do in ia64 & x86.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
o Currently, during kexec reboot, IOAPIC is re-programmed back to virtual
wire mode if there was an i8259 connected to it. This enables getting
timer interrupts in second kernel in legacy mode.
o After putting into virtual wire mode, IOAPIC delivers the i8259 interrupts
to CPU0. This works well for kexec but not for kdump as we might crash
on a different CPU and second kernel will not see timer interrupts.
o This patch modifies the redirection table entry to deliver the timer
interrupts to the cpu we are rebooting (instead of hardcoding to zero).
This ensures that second kernel receives timer interrupts even on a
non-boot cpu.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When we re-calibrate the frequency, it is likely that an interrupt (as for
example the main system clock) will be triggered by the system. Therefore
the calibration may not be accurate. This will also provide a fix to bug
#5266.
Many thanks to Larry Finger for helping resolving this issue.
Signed-off-by: Bruno Ducrot <ducrot@poupinou.org>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix screen blanking on BIOSes that return APM_NOT_ENGAGED when APM enabled
screen blanking is not turned on.
The original code only tried to set the state on device 0x100, and then
0x1FF, and I added 0x101 to the mix too.
- Clean up logic in apm_console_blank().
- Prevent the error message from printing out twice.
Cc: Jordan Crouse <jordan.crouse@amd.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Provide basic support for the AMD Geode GX and LX processors.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed the unused variable "rv".
Signed-off-by: Daniel Marjamaki <daniel.marjamaki@comhem.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Removed the unused variable "rv".
Signed-off-by: Daniel Marjamaki <daniel.marjamaki@comhem.se>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Missing newline in printk.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 'make rodata read-only' patch in -mm exposes a latent bug in the 32-bit
change_page_attr() function, which causes certain CPUs (Those with NX
basically) to reboot instantly after pages are marked read-only.
The same bug got fixed a while back on x86-64, but never got propagated to
i386.
Stuart Hayes from Dell also picked up on this last June, but it never got
fixed, as the only thing affected by it aparently was the nvidia driver.
Blatantly stealing description from his post..
"It doesn't appear to be fixed (in the i386 arch). The
change_page_attr()/split_large_page() code will still still set all the
4K PTEs to PAGE_KERNEL (setting the _PAGE_NX bit) when a large page
needs to be split.
This wouldn't be a problem for the bulk of the kernel memory, but there
are pages in the lower 4MB of memory that's free, and are part of large
executable pages that also contain kernel code. If change_page_attr()
is called on these, it will set the _PAGE_NX bit on the whole 2MB region
that was covered by the large page, causing a large chunk of kernel code
to be non-executable."
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Cc: <Stuart_Hayes@Dell.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we are using hotplug enabled kernel, then make bigsmp the default mode.
Signed-off-by: Ashok Raj <ashok.raj@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Allow SPARSEMEM to be enabled on non-numa x86 systems. This is made
dependant on EXPERIMENTAL also being set. When an in-tree user (such as
simulated numa) exists it should be made dependant on that.
The plan is to have no options and no selector as normal when
!EXPERIMENTAL. When EXPERIMENTAL we enable the FLATMEM and SPARSEMEM
options for X86_PC whilst maintaining DISCONTIGMEM and SPARSEMEM for NUMA.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Mark some key kernel datastructures readonly. This patch was previously
posted on Jun 28th but was back then not merged because nothing was enforcing
rodata anyway.. well that changed now :)
Patch by Christoph Lameter <christoph@lameter.com> and Dave Jones
<davej@redhat.com>
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86-64 specific parts to make the .rodata section read only
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Bug fix required for the .rodata work on x86-64:
when change_page_attr() and friends need to break up a 2Mb page into 4Kb
pages, it always set the NX bit on the PMD, which causes the cpu to consider
the entire 2Mb region to be NX regardless of the actual PTE perms. This is
fine in general, with one big exception: the 2Mb page that covers the last
part of the kernel .text! The fix is to not invent a new permission for the
new PMD entry, but to just inherit the existing one minus the PSE bit.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
x86 specific parts to make the .rodata section read only
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Andi Kleen <ak@muc.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the "temporary debugging check" which has managed to live for quite
some time, and is clearly unneeded. The mm can never be live at this point,
so clearly checking the LDT in the mm->context is redundant as well.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM BIOS code has a protective wrapper that runs it only on CPU zero. Thus,
no need to set APM BIOS segments in the GDT for other CPUs.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Stop deleting NT bit from EFLAGS. See arch/i386/kernel/head.S line 223, which
does something even better.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
PnP BIOS data, code, and 32-bit entry segments all have fixed limits as well;
set them in the GDT rather than adding more code. It would be nice to add
these fixups to the boot GDT rather than setting the GDT for each CPU; perhaps
I can wiggle this in later, but getting it in before the subsys init looks
tricky.
Also, make some progress on deprecating the ugly Q_SET_SEL macros.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The one remaining caller of set_limit, the PnP BIOS code, calls into the PnP
BIOS, passing kernel parameters in and out. These parameteres may be passed
from arbitrary kernel virtual memory, so they deserve strict protection to
stop a bad BIOS from smashing beyond the object size.
Unfortunately, the use of set_limit was badly botching this by setting the
limit in terms of pages, when it really should have byte granularity.
When doing this, I discovered my BIOS had the buggy code during the "get
system device node" call:
mov ax, es:[bx]
Which is harmless, but has a trivial workaround.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Since APM BIOS segment limits are now fixed, set them in head.S GDT and don't
use the complicated _set_limit() macro expansion.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
APM BIOSes have many bugs regarding proper representation of the appropriate
segment limits for calling the BIOS. By default, APM_RELAX_SEGMENTS is always
turned on to support running the APM BIOS on these buggy machines. Keeping
64k limits poses very little danger to the kernel, because the pages where the
APM BIOS is located will always be in low physical memory BIOS areas, which
should already be marked reserved, and only buggy BIOSes would possibly
overstep the segment bounds with writes to data anyway.
Since forcing stricter limits breaks many machines and is not default
behavior, it seems reasonable to deprecate the older code which may cause APM
BIOS to fault.
If you really have a badly enough broken APM BIOS that you have to turn off
APM_RELAX_SEGMENTS, seems like the best recourse here would be to disable the
APM BIOS and / or not compile it into your kernel to begin with, and / or add
your system to the known bad list.
The reason I want to deprecate this code is there is underlying brokenness
with the set_limit macros, and getting rid of many of the call sites rather
than rewriting them seems to be the simplest and most correct course of
action.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So some 486 processors do have CR4 register. Allow them to present it in
register dumps by using the old fault technique rather than testing processor
family.
Thanks to Maciej for noticing this.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Other than apparently commonly assumed, the bound instruction does not
require the corresponding IDT entry to have DPL 3.
Acked-by: "Seth, Rohit" <rohit.seth@intel.com>
Acked-by: Zachary Amsden <zach@vmware.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move some code unrelated to any dealing with hardware bugs from i386's
bugs.h to a more logical place.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than blindly re-enabling interrupts in die(), save their state
upon entry and then restore that state.
If the kernel is in really bad condition and faults with interrupts disabled,
re-enabling them in die() may cause even more trouble, implying more chances
of data corruption.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make GDT page aligned and page padded to support running inside of a
hypervisor. This prevents false sharing of the GDT page with other hot
data, which is not allowed in Xen, and causes performance problems in
VMware.
Rather than go back to the old method of statically allocating the GDT
(which wastes unneded space for non-present CPUs), the GDT for APs is
allocated dynamically.
Signed-off-by: Zachary Amsden <zach@vmware.com>
Cc: "Seth, Rohit" <rohit.seth@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch improves the signal handling:
(1) It makes do_signal() static as it isn't called from anywhere outside of
the arch code.
(2) It removes the regs argument to all the static functions within that file,
using __frame instead (which is the same thing held in a global register).
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch makes FRV signal handling work properly:
(1) After do_notify_resume() has been called, the work flags must be checked
again (there may be another signal to deliver or the process might require
rescheduling for instance).
(2) After the signal frame is set up on the userspace stack, ptrace() should
be given an opportunity to single-step into the signal handler.
(3) The error state from setting up a signal frame should be passed back up
the call chain.
(4) The segfault handler shouldn't be preemptively reset in the arch if we
fail to deliver a SEGV signal: force_sig() will take care of that.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The attached patch implements futex operations for the FRV architecture. The
operations are applicable to both MMU and no-MMU modes; though the EFAULT
handling will be a little bit of wasted space on the latter.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Commit 3e9e7c1d0b (ppc32: cleanup AMCC PPC40x
eval boards to support U-Boot) broke the kernel for ML300 / EP405.
It still compiles as there's a weak definition of the function in
misc-embedded.c, but the kernel crashes as the bd_t fixup isn't performed.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some custom cards might not need PCI, without this patch, compilation fails.
Signed-off-by: Roger Blofeld <blofeldus@yahoo.com>
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were counting on the bootloader to init some stuff, like get the bus out of
reset and enable accesses.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch takes care of an errata of the MPC5200 by avoiding 32 bits access
in type 1 configuration accesses. All others accesses are still 32 bits wide.
It also adds some mb() since the simple out_be(...) are not sufficient in
this case.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The mpc52xx_pci_fixup_resources is not only called at init but also when there
is a pci hotplug like when a cardbus card is plugged in. So that function is
needed after init too.
Thanks to Asier Llano Palacios for reporting this.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The current iomapping used MBAR_SIZE for the size argument of
io_block_mapping, resulting in a call to setbat with a size argument of 64k
which is invalid.
This patch correct this and maps the whole 0xf0000000->0xffffffff range so
that devices on the local bus are also included in the BAT mapping.
Thanks to Bernhard Kuhn from Metrowerks for pointing this out.
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
That file is a left-over of the 'old' OCP model that should have been erased
during the change to platform model but I forgot it ...
Signed-off-by: Sylvain Munaut <tnt@246tNt.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disable declaration of cpu variable in default_idle function when
building non-SMP kernels.
Signed-off-by: Otavio Salvador <otavio@debian.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Remove the not needed anymore "jumbo" member from ocp_func_emac_data.
Jumbo frame support is handled by PPC4xx EMAC driver internally now.
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Now that i2c_add_driver() doesn't need the module owner to be set by
hand, we can delete it from the drivers. This patch catches all of the
drivers that I found in the current tree (if a driver sets the .owner by
hand, it's not a problem, just not needed.)
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Jean Delvare <khali@linux-fr.org>
We should use the i2c_driver.driver's .name and .owner fields
instead of the i2c_driver's ones.
This patch updates the drivers for arm arch.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
CC: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make I2C_CLIENT_ALLOW_USE the default for all i2c clients. It doesn't
hurt if the usage count is actually never used for any given driver,
and allows for nice code simplifications in i2c-core.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Just about every i2c chip driver sets the I2C_DF_NOTIFY flag, so we
can simply make it the default and drop the flag. If any driver really
doesn't want to be notified when i2c adapters are added, that driver
can simply omit to set .attach_adapter. This approach is also more
robust as it prevents accidental NULL pointer dereferences.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Setting RF (resume flag) allows a debugger to resume execution after a
code breakpoint without tripping the breakpoint again. It is reset by
the CPU after execution of one instruction.
Requested by Stephane Eranian:
"I am trying to the user HW debug registers on i386 and I am running
into a problem with ptrace() not allowing access to EFLAGS_RF for
POKEUSER (see FLAG_MASK). [ ... ] It avoids the need to remove the
breakpoint, single step, and reinstall. The equivalent functionality
exists on IA-64 and is allowed by ptrace()"
Cc: Stephane Eranian <eranian@hpl.hp.com>
Signed-off-by: Chuck Ebbert <76306.1226@compuserve.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
