I have never seen a use of SLAB_DEBUG_INITIAL. It is only supported by
SLAB.
I think its purpose was to have a callback after an object has been freed
to verify that the state is the constructor state again? The callback is
performed before each freeing of an object.
I would think that it is much easier to check the object state manually
before the free. That also places the check near the code object
manipulation of the object.
Also the SLAB_DEBUG_INITIAL callback is only performed if the kernel was
compiled with SLAB debugging on. If there would be code in a constructor
handling SLAB_DEBUG_INITIAL then it would have to be conditional on
SLAB_DEBUG otherwise it would just be dead code. But there is no such code
in the kernel. I think SLUB_DEBUG_INITIAL is too problematic to make real
use of, difficult to understand and there are easier ways to accomplish the
same effect (i.e. add debug code before kfree).
There is a related flag SLAB_CTOR_VERIFY that is frequently checked to be
clear in fs inode caches. Remove the pointless checks (they would even be
pointless without removeal of SLAB_DEBUG_INITIAL) from the fs constructors.
This is the last slab flag that SLUB did not support. Remove the check for
unimplemented flags from SLUB.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since freezable workqueues are broken in 2.6.21-rc
(cf. http://marc.theaimsgroup.com/?l=linux-kernel&m=116855740612755,
http://marc.theaimsgroup.com/?l=linux-kernel&m=117261312523921&w=2)
it's better to change the only user of them, which is XFS, to use "normal"
nonfreezable workqueues.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: David Chinner <dgc@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The semantic effect of insert_at_head is that it would allow new registered
sysctl entries to override existing sysctl entries of the same name. Which is
pain for caching and the proc interface never implemented.
I have done an audit and discovered that none of the current users of
register_sysctl care as (excpet for directories) they do not register
duplicate sysctl entries.
So this patch simply removes the support for overriding existing entries in
the sys_sysctl interface since no one uses it or cares and it makes future
enhancments harder.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: David Howells <dhowells@redhat.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Corey Minyard <minyard@acm.org>
Cc: Neil Brown <neilb@suse.de>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: Jan Kara <jack@ucw.cz>
Cc: Trond Myklebust <trond.myklebust@fys.uio.no>
Cc: Mark Fasheh <mark.fasheh@oracle.com>
Cc: David Chinner <dgc@sgi.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
After Al Viro (finally) succeeded in removing the sched.h #include in module.h
recently, it makes sense again to remove other superfluous sched.h includes.
There are quite a lot of files which include it but don't actually need
anything defined in there. Presumably these includes were once needed for
macros that used to live in sched.h, but moved to other header files in the
course of cleaning it up.
To ease the pain, this time I did not fiddle with any header files and only
removed #includes from .c-files, which tend to cause less trouble.
Compile tested against 2.6.20-rc2 and 2.6.20-rc2-mm2 (with offsets) on alpha,
arm, i386, ia64, mips, powerpc, and x86_64 with allnoconfig, defconfig,
allmodconfig, and allyesconfig as well as a few randconfigs on x86_64 and all
configs in arch/arm/configs on arm. I also checked that no new warnings were
introduced by the patch (actually, some warnings are removed that were emitted
by unnecessarily included header files).
Signed-off-by: Tim Schmielau <tim@physik3.uni-rostock.de>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Many struct inode_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't hide buffer_unwritten behind buffer_delay() and remove the hack that
clears unexpected buffer_unwritten() states now that it can't happen.
Signed-off-by: Dave Chinner <dgc@sgi.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Cc: Timothy Shimmin <tes@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently, XFS uses BH_PrivateStart for flagging unwritten extent state in a
bufferhead. Recently, I found the long standing mmap/unwritten extent
conversion bug, and it was to do with partial page invalidation not clearing
the unwritten flag from bufferheads attached to the page but beyond EOF. See
here for a full explaination:
http://oss.sgi.com/archives/xfs/2006-12/msg00196.html
The solution I have checked into the XFS dev tree involves duplicating code
from block_invalidatepage to clear the unwritten flag from the bufferhead(s),
and then calling block_invalidatepage() to do the rest.
Christoph suggested that this would be better solved by pushing the unwritten
flag into the common buffer head flags and just adding the call to
discard_buffer():
http://oss.sgi.com/archives/xfs/2006-12/msg00239.html
The following patch makes BH_Unwritten a first class citizen.
Signed-off-by: Dave Chinner <dgc@sgi.com>
Acked-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
kmap() is inefficient and does not scale well. kmap_atomic() is a better
choice. Use the generic wrapper function instead of open coding the
kmap-memset-dcache flush-kunmap stuff.
SGI-PV: 960904
SGI-Modid: xfs-linux-melb:xfs-kern:28041a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Patch provided by Eric Sandeen (sandeen@sandeen.net).
SGI-PV: 960897
SGI-Modid: xfs-linux-melb:xfs-kern:28038a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
It makes it incrementally clearer to read the code when the top of a macro
spaghetti-pile only receives the 3 arguments it uses, rather than 2 extra
ones which are not used. Also when you start pulling this thread out of
the sweater (i.e. remove unused args from XFS_BTREE_*_ADDR), a couple
other third arms etc fall off too. If they're not used in the macro, then
they sometimes don't need to be passed to the function calling the macro
either, etc....
Patch provided by Eric Sandeen (sandeen@sandeen.net).
SGI-PV: 960197
SGI-Modid: xfs-linux-melb:xfs-kern:28037a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
xfs_mac.h and xfs_cap.h provide definitions and macros that aren't used
anywhere in XFS at all. They are left-overs from "to be implement at some
point in the future" functionality that Irix XFS has. If this
functionality ever goes into Linux, it will be provided at a different
layer, most likely through the security hooks in the kernel so we will
never need this functionality in XFS.
Patch provided by Eric Sandeen (sandeen@sandeen.net).
SGI-PV: 960895
SGI-Modid: xfs-linux-melb:xfs-kern:28036a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Fixes a few small issues (mostly cosmetic) that were picked up during the
review cycle for the last set of freeze path changes.
SGI-PV: 959267
SGI-Modid: xfs-linux-melb:xfs-kern:28035a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The firstblock argument to xfs_bmap_finish is not used by that function.
Remove it and cleanup the code a bit.
Patch provided by Eric Sandeen.
SGI-PV: 960196
SGI-Modid: xfs-linux-melb:xfs-kern:28034a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Use the the generic VFS attr flags where appropriate instead of open
coding them to the same values.
Patch provided by Eric Sandeen.
SGI-PV: 960868
SGI-Modid: xfs-linux-melb:xfs-kern:28033a
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
wake_up's implementation does an implicit memory barrier so the explicit
memory barrier is not needed in vfs_sync_worker.
Patch provided by Ralf Baechle.
SGI-PV: 960867
SGI-Modid: xfs-linux-melb:xfs-kern:28032a
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
Removes unneeded sysctl insert at head behaviour. Cleans up sysctl
definitions to use C99 initialisers. Patch provided by Eric W. Biederman.
SGI-PV: 960192
SGI-Modid: xfs-linux-melb:xfs-kern:28031a
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The problem is the two callers of xfs_iozero() are rounding out the range
to be zeroed to the end of a fsb and in some cases this extends past the
new eof. The call to commit_write() in xfs_iozero() will cause the Linux
inode's file size to be set too high.
SGI-PV: 960788
SGI-Modid: xfs-linux-melb:xfs-kern:28013a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
record.
The current Linux XFS freeze code is a mess. We flush the metadata buffers
out while we are still allowing new transactions to start and then fail to
flush the dirty buffers back out before writing the unmount and dummy
records to the log.
This leads to problems when the frozen filesystem is used for snapshots -
we do log recovery on a readonly image and often it appears that the log
image in the snapshot is not correct. Hence we end up with hangs, oops and
mount failures when trying to mount a snapshot image that has been created
when the filesystem has not been correctly frozen.
To fix this, we need to move th metadata flush to after we wait for all
current transactions to complete in teh second stage of the freeze. This
means that when we write the final log records, the log should be clean
and recovery should never occur on a snapshot image created from a frozen
filesystem.
SGI-PV: 959267
SGI-Modid: xfs-linux-melb:xfs-kern:28010a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Donald Douwsma <donaldd@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
When writing less than a filesystem block of data into an unwritten extent
via buffered I/O, __xfs_get_blocks fails to set the buffer new flag. As a
result, the generic code will not zero either edge of the block resulting
in garbage being written to disk either side of the real data. Set the
buffer new state on bufferd writes to unwritten extents to ensure that
zeroing occurs.
SGI-PV: 960328
SGI-Modid: xfs-linux-melb:xfs-kern:28000a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
After filesystem recovery the superblock is re-read to bring in any
changes. If the per-cpu superblock counters are not re-initialized from
the superblock then the next time the per-cpu counters are disabled they
might overwrite the global counter with a bogus value.
SGI-PV: 957348
SGI-Modid: xfs-linux-melb:xfs-kern:27999a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
SGI-PV: 956323
SGI-Modid: xfs-linux-melb:xfs-kern:27940a
Signed-off-by: Kevin Jamieson <kjamieson@bycast.com>
Signed-off-by: David Chatterton <chatz@sgi.com>
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The block reservation mechanism has been broken since the per-cpu
superblock counters were introduced. Make the block reservation code work
with the per-cpu counters by syncing the counters, snapshotting the amount
of available space and then doing a modifcation of the counter state
according to the result. Continue in a loop until we either have no space
available or we reserve some space.
SGI-PV: 956323
SGI-Modid: xfs-linux-melb:xfs-kern:27895a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The free block modification code has a 32bit interface, limiting the size
the filesystem can be grown even on 64 bit machines. On 32 bit machines,
there are other 32bit variables in transaction structures and interfaces
that need to be expanded to allow this to work.
SGI-PV: 959978
SGI-Modid: xfs-linux-melb:xfs-kern:27894a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Tim Shimmin <tes@sgi.com>
functions, but they
a) ignore the flags parameter completely, and b) are never called
directly, only via the flag-less defines anyway
So, drop the #define indirection, and rename mraccessf to mraccess, etc.
SGI-PV: 959138
SGI-Modid: xfs-linux-melb:xfs-kern:27711a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The existing per-cpu superblock counter code uses the global superblock
spin lock when we approach ENOSPC for global synchronisation. On larger
machines than this code was originally tested on this can still get
catastrophic spinlock contention due increasing rebalance frequency near
ENOSPC.
By introducing a sleeping lock that is used to serialise balances and
modifications near ENOSPC we prevent contention from needlessly from
wasting the CPU time of potentially hundreds of CPUs.
To reduce the number of balances occuring, we separate the need rebalance
case from the slow allocate case. Now, a counter running dry will trigger
a rebalance during which counters are disabled. Any thread that sees a
disabled counter enters a different path where it waits on the new mutex.
When it gets the new mutex, it checks if the counter is disabled. If the
counter is disabled, then we _know_ that we have to use the global counter
and lock and it is safe to do so immediately. Otherwise, we drop the mutex
and go back to trying the per-cpu counters which we know were re-enabled.
SGI-PV: 952227
SGI-Modid: xfs-linux-melb:xfs-kern:27612a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
gcc-4.1 and more recent aggressively inline static functions which
increases XFS stack usage by ~15% in critical paths. Prevent this from
occurring by adding noinline to the STATIC definition.
Also uninline some functions that are too large to be inlined and were
causing problems with CONFIG_FORCED_INLINING=y.
Finally, clean up all the different users of inline, __inline and
__inline__ and put them under one STATIC_INLINE macro. For debug kernels
the STATIC_INLINE macro uninlines those functions.
SGI-PV: 957159
SGI-Modid: xfs-linux-melb:xfs-kern:27585a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: David Chatterton <chatz@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The {test,set,clear}_bit() operations take a bit index for the bit to
operate on. The XBT_* flags are defined as bit fields which is incorrect,
not to mention the way the bit fields are enumerated is broken too. This
was only working by chance.
Fix the definitions of the flags and make the code using them use the
{test,set,clear}_bit() operations correctly.
SGI-PV: 958639
SGI-Modid: xfs-linux-melb:xfs-kern:27565a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The message buffer used by cmn_err() is only 256 bytes and some CXFS
messages were exceeding this length. Since we were using vsprintf() and
not checking for buffer overruns we were clobbering memory beyond the
buffer. The size of the buffer has been increased to 1024 bytes so we can
capture these larger messages and we are now using vsnprintf() to prevent
overrunning the buffer size.
SGI-PV: 958599
SGI-Modid: xfs-linux-melb:xfs-kern:27561a
Signed-off-by: Lachlan McIlroy <lachlan@sgi.com>
Signed-off-by: Geoffrey Wehrman <gwehrman@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
At the last stage of a freeze, we flush the buftarg synchronously over and
over again until it succeeds twice without skipping any buffers.
The delwri list flush skips pinned buffers, but tries to flush all others.
It removes the buffers from the delwri list, then tries to lock them one
at a time as it traverses the list to issue the I/O. It holds them locked
until we issue all of the I/O and then unlocks them once we've waited for
it to complete.
The problem is that during a freeze, the filesystem may still be doing
stuff - like flushing delalloc data buffers - in the background and hence
we can be trying to lock buffers that were on the delwri list at the same
time. Hence we can get ABBA deadlocks between threads doing allocation and
the buftarg flush (freeze) thread.
Fix it by skipping locked (and pinned) buffers as we traverse the delwri
buffer list.
SGI-PV: 957195
SGI-Modid: xfs-linux-melb:xfs-kern:27535a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Tim Shimmin <tes@sgi.com>
The XFS quiet mount logic was inverted making quiet mounts noisy and vice
versa. Fix it.
SGI-PV: 958469
SGI-Modid: xfs-linux-melb:xfs-kern:27520a
Signed-off-by: David Chinner <dgc@sgi.com>
Signed-off-by: Eric Sandeen <sandeen@sandeen.net>
Signed-off-by: Tim Shimmin <tes@sgi.com>
XFS appears to call clear_page_dirty to get the mapping tree dirty tag
set correctly at the same time the page dirty flag is cleared. I note
that this can be done by set_page_writeback() if we clear the dirty flag
on the page first when we are writing back the entire page.
Hence it seems to me that the XFS call to clear_page_dirty() could
easily be substituted by clear_page_dirty_for_io() followed by a call to
set_page_writeback() to get the mapping tree tags set correctly after
the page has been marked clean.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The only time it is safe to call aio_complete() is when the ->ki_retry
function returns -EIOCBQUEUED to the AIO core. direct_io_worker() has
historically done this by relying on its caller to translate positive return
codes into -EIOCBQUEUED for the aio case. It did this by trying to keep
conditionals in sync. direct_io_worker() knew when finished_one_bio() was
going to call aio_complete(). It would reverse the test and wait and free the
dio in the cases it thought that finished_one_bio() wasn't going to.
Not surprisingly, it ended up getting it wrong. 'ret' could be a negative
errno from the submission path but it failed to communicate this to
finished_one_bio(). direct_io_worker() would return < 0, it's callers
wouldn't raise -EIOCBQUEUED, and aio_complete() would be called. In the
future finished_one_bio()'s tests wouldn't reflect this and aio_complete()
would be called for a second time which can manifest as an oops.
The previous cleanups have whittled the sync and async completion paths down
to the point where we can collapse them and clearly reassert the invariant
that we must only call aio_complete() after returning -EIOCBQUEUED.
direct_io_worker() will only return -EIOCBQUEUED when it is not the last to
drop the dio refcount and the aio bio completion path will only call
aio_complete() when it is the last to drop the dio refcount.
direct_io_worker() can ensure that it is the last to drop the reference count
by waiting for bios to drain. It does this for sync ops, of course, and for
partial dio writes that must fall back to buffered and for aio ops that saw
errors during submission.
This means that operations that end up waiting, even if they were issued as
aio ops, will not call aio_complete() from dio. Instead we return the return
code of the operation and let the aio core call aio_complete(). This is
purposely done to fix a bug where AIO DIO file extensions would call
aio_complete() before their callers have a chance to update i_size.
Now that direct_io_worker() is explicitly returning -EIOCBQUEUED its callers
no longer have to translate for it. XFS needs to be careful not to free
resources that will be used during AIO completion if -EIOCBQUEUED is returned.
We maintain the previous behaviour of trying to write fs metadata for O_SYNC
aio+dio writes.
Signed-off-by: Zach Brown <zach.brown@oracle.com>
Cc: Badari Pulavarty <pbadari@us.ibm.com>
Cc: Suparna Bhattacharya <suparna@in.ibm.com>
Acked-by: Jeff Moyer <jmoyer@redhat.com>
Cc: <xfs-masters@oss.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change all the uses of f_{dentry,vfsmnt} to f_path.{dentry,mnt} in the xfs
filesystem.
Signed-off-by: Josef "Jeff" Sipek <jsipek@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make the workqueues used by XFS freezeable, so their worker threads don't
submit any I/O after the suspend image has been created.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Cc: David Chinner <dgc@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
