These were previous littered around tlb-nommu.c and pg-nommu.c, though at
this point there are more stubs than are strictly TLB or page op related,
so just consolidate them in a single nommu.c.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This builds in the newly created cache.c (renamed from pg-mmu.c) for both
MMU and NOMMU configurations. The kmap_coherent() stubs and alias
information recorded by each CPU family takes care of doing the right
thing while enabling the code to be commonly shared.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This plugs in kmap_coherent() for the non-SH4 cases to permit the
pg-mmu.c bits to be used generically across all CPUs. SH-5 is still in
the TODO state, but will move over to fixmap and the generic interface
gradually.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out the SH-4 __flush_xxx_region() functions and defines them
as weak symbols. This allows us to provide optimized versions without
having to ifdef cache-sh4.c to death.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the SH-4 page clear/copy ops are generic, they can be used for
all platforms with CONFIG_MMU=y. SH-5 remains the odd one out, but it too
will gradually be converted over to using this interface.
SH-3 platforms which do not contain aliases will see no impact from this
change, while aliasing SH-3 platforms will get the same interface as
SH-4.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This wires up clear_user_highpage() on SH-4 and subsequently converts the
SH7705 32kB cache mode over to using it. Now that the SH-4 implementation
handles all of the dcache purging directly in the aliasing case, there is
no need to do this in the default clear_page() implementation.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for extended ASIDs (up to 16-bits) on newer SH-X3 cores
that implement the PTAEX register and respective functionality. Presently
only the 65nm SH7786 (90nm only supports legacy 8-bit ASIDs).
The main change is in how the PTE is written out when loading the entry
in to the TLB, as well as in how the TLB entry is selectively flushed.
While SH-X2 extended mode splits out the memory-mapped U and I-TLB data
arrays for extra bits, extended ASID mode splits out the address arrays.
While we don't use the memory-mapped data array access, the address
array accesses are necessary for selective TLB flushes, so these are
implemented newly and replace the generic SH-4 implementation.
With this, TLB flushes in switch_mm() are almost non-existent on newer
parts.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This provides a method for supporting fixed PMB mappings inherited from
the bootloader, as an alternative to the dynamic PMB mapping currently
used by the kernel. In the future these methods will be combined.
P1/P2 area is handled like a regular 29-bit physical address, and local
bus device are assigned P3 area addresses.
Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the sh64 /proc/asids entry to debugfs and enables it for
all SH parts that have debugfs enabled.
On MMU systems this can be used to determine which processes are using
which ASIDs which in turn can be used for finer grained cache tag
analysis.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the PMB enabled, only P1SEG and up are covered by the PMB mappings,
meaning that situations where out-of-bounds physical addresses are read
from will lead to TLB reset after the PMB miss, allowing for use cases
like dd if=/dev/mem to reset the TLB.
Fix this up to make sure the reference is between __MEMORY_START (phys)
and __pa(high_memory). This is coherent across all variants of sh/sh64
with and without MMU, though the PMB bug itself is only applicable to
SH-4A parts.
Reported-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
