As Nicolas and Russell pointed out, CLOCK_TICK_RATE is no more
a constant on PXA when multiple processors and platforms are
selected, change TIMER_FREQ in rtc-sa1100.c into a variable.
Since the code to decide the clock tick rate is re-used from
timer.c, introduce a common get_clock_tick_rate() for this.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Changes made as suggested by Eric Miao (including fix to map_io
silly mistake!).
Originally designed by Intel, now sold by Crossbow (www.xbow.com).
Very little actually on board. The patch includes sensors and
similar as found on commonly occurring daughter boards.
Some of the drivers are not in mainline as yet as they are either
part of the IIO subsystem or need a lot of work before submission.
What is the position wrt to putting them in i2c board configs etc?
Support for these boards has been maintained outside the kernel
for a long time, but now that there is a good da9030 pmic driver
available the last major hurdle no longer exists.
All comments welcomed.
The Imote2's big brother (stargate2) will follow once any problems
with this one have been cleaned up and a few bits and bobs have
been added to the da903x driver. Hopefully the cc2420 driver will
get cleaned up and submitted in the not too distant future as
well.
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
I2C platform data setups.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Matrix and single key setups for all phones.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Antonio Ospite <ospite@studenti.unina.it>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Pin configs for different generations and phones.
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Our bootloader now supports ATAGS_MEM
Signed-off-by: Daniel Ribeiro <drwyrm@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Some smart panel requires a delay between command sequences, while PXA
LCD controller didn't provide such one, let's emulate this by software.
A software delay marker can be inserted into the command sequence, once
pxafb_smart_queue() detects this, it flushes the previous commands and
delay for a specified number of milliseconds.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
For smart panels (LCD panel with internal framebuffer), the following
LCCR3 register bits have different meanings than the parallel one:
LCCR3_PCP - controls the L_PCLK_WR polarity
LCCR3_HSP - controls the L_LCLK_A0 polarity
LCCR3_VSP - controls the L_FCLK_RD polarity
To keep minimum change to the original parallel timing, the .lcd_conn
flags and 'pxafb_mode_info.sync' are re-used to reflect this:
LCD_PCLK_EDGE_{RISE,FALL} - configures LCCR3_PCP
sync & FB_SYNC_{HOR,VERT}_HIGH_ACT - configures LCCR3_{HSP,VSP}
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patchset provides support for the TMIO based IO controller used in the
Toshiba e-series PDAs.
Signed-off-by: Ian Molton <spyro@f2s.com>
Acked-by: Samuel Ortiz <sameo@openedhand.com>
Acked-by: Eric Miao <eric.y.miao@gmail.com>
Fix kernel-doc notation to use correct syntax. Even though this should be
moved to where the function is actually implemented...
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
drivers/built-in.o: In function `pci_set_consistent_dma_mask':
hid-quirks.c:(.text+0x2664): multiple definition of `pci_set_consistent_dma_mask'
drivers/built-in.o: In function `pci_set_dma_mask':
hid-quirks.c:(.text+0x42c4): multiple definition of `pci_set_dma_mask'
because drivers/pci/pci.c was not seeing the definition disabling these
functions.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The gpio setup for AM200 specific GPIO pins should be done in the AM200
code rather than in generic gumstix code.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch adds HP iPAQ h5000's (h5400, h5500) basic definitions.
Kernel will able to boot, work via serial console, mount filesystems
placed on flashes and run USB gadgets (g_ether by default).
Other device drivers (frame buffer, LCD, touchscreen, backlight,
bluetooth, w1/battery, ...) are depend on SAMCOP and MediaQ
SoCs/MFDs, drivers to which will be submitted too, after massive
cleanups.
This machine will be used as "real user" for these new drivers.
This is an updated version of the patch, which contains fixes proposed on
linux-arm-kernel mailing list.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Milan Plzik <milan.plzik@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add mapping for system ROM using physmap-flash mapping.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add platform data necessary to support tmiofb on tosa.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Take advantage of the newly created wm97xx battery driver
and remove useless code in mioa701 board code. Add also the
ac connection detect capability after the matching gpio was
discovered.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The charger enable gpio is straight (1 means draw from USB
Vbus, 0 mean do not draw). The USB Vbus sensing is inverted
(1 means no Vbus voltage sensed, 0 means Vbus voltage
present).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Change the halt and reboot method from gpio based to "jump
to ROM IPL beginning". This gives control back to IPL, which
without PowerOn key pressed, will put the device into deep
sleep until PowerOn is pressed for 1 second.
But this has the benefit of keeping the RTC registers across
reboots, which is good for OS change.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add GPIO configuration and platform specific declarations
to make Mitac Mio A701 camera chip work. The chip is a
Micron MT9M111 CMOS sensor, based on PXA QIF interface and
I2C bus for sensor control.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Since mioa701 board has migrated to the mfp architecture,
low power gpio setup is now correctly handled even when gpio
led driver is not loaded, and leds and vibrator don't stay
activated in suspend mode (especially vibrator).
Remove the not needed anymore dependency.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Add IO memory and IRQ ressources for pxa based SoC to be
able to use the new rtc-pxa driver.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch implements Eric Miao's idea to detect the correct value of
sdram_rows by inspecting the MDCNFG register settings.
It is only tested on two pxa27x devices with 64MB RAM (magician and
hx4700) so far.
Signed-off-by: Philipp Zabel <philipp.zabel@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Following the removal of the "->policy" usage for PXA255 in patch
459fc208ab (cpufreq: remove
policy->governor setting in drivers initialization), this patch
introduces an option (called "pxa255_turbo_table") to select either
the "run" or "turbo" frequency table.
It also cures the runtime warning that was printed each time the
frequency was changed.
Got rid of all references to CPUFREQ_POLICY_* for pxa255, and sticked
with the run/turbo thing.
Tested on an Arcom/Eurotech Viper.
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
GPIO3/GPIO4 are a bit special on pxa27x, since it depends on PCFR/PI2C_EN
bit, add their definitions here with comments.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Let's put these devices into a central place even if they are now
processor specific, as they might be re-used in later processors.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The optimal change would be to move the AC97 register definitions into
the AC97 driver, unfortunately, the registers are shared between several
files. Move them into a dedicated regs-ac97.h first.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
There two are internal registers that are used to control the power
management of the Internal Memory (i.e. Internal SRAM). They are
referenced nowhere and removed here to simplify pxa-regs.h a bit.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
We now have generic PWM API for PXA, the PWM registers definitions are
now used nowhere, and it is not encouraged to manipulate them directly
by driver code.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
pxa_gpio_{get,set}_value() are not used anymore, remove them from hardware.h.
Declaration of pxa_gpio_mode() is still being referenced and thus moved into
pxa2xx-gpio.h
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Original patch from Marek Vasut, the problems with PXA26x are:
1. there are additional 4 GPIOs 86,87,88,89 have their direction bits
inverted in GPDR2, as well as their alternate function bits being
'1' for their GPIO functionality in GAFRx
2. there is no easy way to decide if the processor is a pxa26x or a
pxa250/pxa255 at run-time, so the assumption here is the pxa26x
will be treated as one of the pxa25x variants, and board code
should have a better knowledge of the processor it is featured
Introduce pxa26x_init_irq() for the second purpose, and treat the
additional GPIOs > 85 on PXA25x specially.
Kconfig option CONFIG_CPU_PXA26x is introduced to optimize the code
a bit when PXA26x support isn't needed. Board config options have
to select this to enable the support for PXA26x.
__gpio_is_inverted() will be optimized way when CONFIG_CPU_PXA26x
isn't selected.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit da1a3dc0eb.
The originally proposed way in the above commit is incorrect. And
there is no easy way to distinguish between pxa25x and pxa26x at
run-time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The 'gpio_nr' can really be inferred by 'pxa_last_gpio', and since we
already have that variable, remove the unnecessary 'gpio_nr' now.
Also, fix the incorrect GPIO number passed in pxa27x_init_irq().
Note: pxa_last_gpio should be initialized earlier, and this is true
since it's been assigned in machine_desc->init_irq().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
PXA SoC have several GPIOs muxed on only one wakeup source.
Add support for these wakeup sources which were missing
in mfp core support.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Both of these symbols should be defined by a platform, or neither
should be defined. Ensure that all platforms conform.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
As Al did for Versatile in 2ad4f86b60,
add a typesafe __io implementation for platforms to use. Convert
platforms to use this new simple typesafe implementation.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When ISA_DMA_API is unset, we're not implementing the ISA DMA API,
so there's no point in publishing the prototypes via asm/dma.h, nor
including the machine dependent parts of that API.
This allows us to remove a lot of mach/dma.h files which don't contain
any useful code. Unfortunately though, some platforms put their own
private non-ISA definitions into mach/dma.h, so we leave these behind
and fix the appropriate #include statments.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Avoid unnecessarily pollution of the kernel's namespace by avoiding
mach/hardware.h. Include this header file where necessary.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Let's provide an overridable default instead of having every machine
class define __virt_to_bus and __bus_to_virt to the same thing. What
most platforms are using is bus_addr == phys_addr so such is the default.
One exception is ebsa110 which has no DMA what so ever, so the actual
definition is not important except only for proper compilation. Also
added a comment about the special footbridge bus translation.
Let's also remove comments alluding to set_dma_addr which is not
(and should not) be commonly used.
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Where devices only have one consumer, passing a consumer clock ID
has no real benefit. Remove it.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Rather than:
config CPU_BLAH
bool
depends on ARCH_FOO || MACH_BAR
default y if ARCH_FOO || MACH_BAR
arrange for ARCH_FOO and MACH_BAR to select CPU_BLAH directly.
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Acked-by: Brian Swetland <swetland@google.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Acked-by: Nicolas Bellido <ml@acolin.be>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
0 is a valid GPIO number, use a negative number to specify, that this camera
doesn't have a GPIO for bus-width switching.
Signed-off-by: Guennadi Liakhovetski <lg@denx.de>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
The G3IPL expects the value at RAM address 0xa020b020 to be
exactly 1 to setup the bluetooth GPIOs properly. The actual
code got a value from gpio_get_value() which was not 1, but
a "not equal to 0" integer.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
In the resume bootstrap, the early disable address is wrong.
Fix it to RAM address 0xa020b000 instead of 0xa0200000, and
make it consistent with RESUME_ENABLE_ADDR in mioa701.c.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This patch makes do_hw_reset the default reboot behavior when nothing
else matches. This restores reboot functionality on gumstix basix
devices where reboot=cold is the default boot argument.
Signed-off-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Acked-by: Eric Miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The original incorrect configuration caused GPIO79_nCS_3 being overriden,
thus resulted in the NAND flash not being detected. The real PSKTSEL pin
is on GPIO104 instead of GPIO79.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
this patch adds asoc audio driver for pxa27x based Palm PDAs. I tested it for
palmtx, t5 and ld, it should work with palmz72 as well (slapin, please test).
I sent it here some time ago, but now I got to fixing bugs in it. It should
be somehow mostly ok and ready for applying.
[Converted to use snd_soc_dapm_nc_pin() and bool Kconfig -- broonie]
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Finally move registration of sharpsl-nand device to board-specific code.
sharpsl nand driver is now clean and simple.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
corgi_lcd has symbol conflict with corgi_bl driver.
Fix it by renaming common symbol in new corgi_lcd driver.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Eric Miao <eric.miao@marvell.com>
* 'for-linus' of master.kernel.org:/home/rmk/linux-2.6-arm:
[ARM] pxa: corgi backlight driver should not select ssp drivers
[ARM] 5321/1: Kirkwood: fix typo in Makefile
[ARM] 5320/1: fix assembly constraints in implementation of do_div()
[ARM] 5318/1: Swap the PRRR and NMRR values in proc-v7.S
[ARM] 5316/1: AT91: oops (regression) fix on gpio irq
[ARM] msm: vreg interface to msm7k pmic
[ARM] msm: dma: various basic dma improvements and bugfixes
[ARM] msm: clock: provide clk_*() api support for
[ARM] msm: clean up iomap and devices
[ARM] msm: add proc_comm support, necessary for clock and power control
[ARM] msm: rename ARCH_MSM7X00A to ARCH_MSM
[ARM] pxa/spitz: fix unbalance parenthesis in header file spitz.h
[ARM] pxa: update {corgi,spitz}_defconfig to favor SPI-based drivers
[ARM] pxa: fix the corgi_ssp.c dependency issue in {corgi,spitz}_defconfig
Revert "[ARM] pxa/corgi: remove now unused corgi_ssp.c and corgi_lcd.c"
* 'for-linus' of git://git.o-hand.com/linux-rpurdie-backlight:
backlight: Add driver for Tabletkiosk Sahara TouchIT-213 Tablet PC
backlight: da903x: Add backlight driver for DA9030/DA9034
tosa: add support for bl/lcd driver
backlight: add support for Sharp SL-6000 LCD and backlight drivers
Separate building of corgi_ssp.c, and introduce a new hidden config option
CONFIG_CORGI_SSP_DEPRECATED for this. Aslo mark corgi_ts.c and corgi_bl.c
as deprecated.
This unbreaks the legacy configs in {corgi,spitz}_defconfig, however, SPI
based ADS7846 touchscreen driver and a new SPI-based corgi_lcd.c driver
with integrated backlight support are recommended.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
This reverts commit 68677ab3d0.
A smoother migration path would be making corgi_ts.c and other drivers
depending on corgi_ssp.c and corgi_lcd.c to depend on BROKEN instead,
and still allows those to exist around for some time.
Signed-off-by: Eric Miao <eric.miao@marvell.com>
On Sharp SL-6000 lcd/backlight is a bit complex, so add two drivers
one for lcd-driving chip, other one for dac regulating the backlight
LEDS.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
