This stubs in clk_get_sys() from the ARM clkdev implementation.
Tentatively conver the clk_get() lookup code to use this, and once the
rest of the in-tree users are happy with this, it can replace the
fallback lookups.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The only user for this is the SH-Mobile r_clk, which is now added as a
root clock and can be kicked via propagate_rate() as usual. Given that,
there is no longer any need for the special clk_recalc_rate(), so we kill
it off.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This tidies up the set_rate hack that the on-chip clocks were abusing to
trigger rate propagation, which is now handled generically.
Additionally, now that CLK_ENABLE_ON_INIT is wired up where it needs to
be for these clocks, the clk_enable() can go away. In some cases this was
bumping up the refcount higher than it should have been.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This causes the generic clk_set_parent() implementation to be a bit more
intelligent. A clk_reparent() is added to move the clock over to the new
parent's sibling list, which then allows the generic rate propagation
code to succeed. This also becomes a nop if the new and old parents are
unchanged.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are a couple of instances where a clk_enable() can fail, which the
SH-Mobile code presently handles, but doesn't get reported all the way
back up. This fixes up the return type so the errors make it all the way
down to the drivers.
Additionally, we now also error out properly if the parent enable fails.
Prep work for aggressively turning off unused clocks on boot.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There is no real distinction here in behaviour, either a clock needs to
be enabled on initialiation or not. The ALWAYS_ENABLED flag was always
intended to only apply to clocks that were physically always on and could
simply not be disabled at all from software. Unfortunately over time this
was abused and the meaning became a bit blurry.
So, we kill off both of all of those paths now, as well as the newer
NEEDS_INIT flag, and consolidate on a CLK_ENABLE_ON_INIT. Clocks that
need to be enabled on initialization can set this, and it will purposely
enable them and bump the refcount up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This resyncs the rate propagation strategy with the scheme used by the
OMAP clock framework. Child clocks are tracked on a list under each
parent and propagation happens there specifically rather than constantly
iterating over the global clock list.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a followparent_recalc() helper for clocks that just follow the
parent's rate. Switch over the few CPUs that use this scheme for some of
their clocks.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7780. Both clockevent
and clocksource support is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Update intc tables and platform data to use one linux irq
per maskable interrupt source instead of keeping the one-to-one
mapping between vectors and linux irqs.
This fixes potential irq masking issues for sh7760 hardware
blocks such as DMAC/TMU2/REF.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7760. Both clockevent
and clocksource support is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh775x. Both clockevent
and clocksource support is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds the clock specifier to all of the SH-Mobile sh-sci ports.
Impacted CPUs are SH7343/SH7366/SH7722/SH7723/SH7724.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7723. Both clockevent
and clocksource support is enabled. While at it, adjust the
CMT clocksource rating to prioritize the TMU.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch enables the TMU clocksource on sh7722.
To prioritize TMU over CMT we also adjust the CMT
clock source rating.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch updates the clock framework use count code.
With this patch the enable() and disable() callbacks
only get called when counting from and to zero.
While at it the kref stuff gets replaced with an int.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds sh_tmu support to the SH-5 subtypes, which subsequently allows
us to kill off time_64.c and use the now generic time_32.c. As a bonus,
SH-5 now supports highres timers and tickless for the first time.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that the onchip_remap() mess is sorted out, the rtc-sh support code
for SH-5 can follow the same approach as the other CPUs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7785. Both clockevent
and clocksource support is enabled.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Make sure that clk->ops->init() only gets called once in
the case of CLK_ALWAYS_ENABLED. Without this patch the
init() callback may be called multiple times.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Presently this is special-cased for early initialization. While there are
situations where these static early initializations are still necessary,
with minor changes it is possible to use this for the regular ioremap
implementation as well. This allows us to kill off the special-casing for
the remap completely and to start tidying up all of the SH-5
special-casing in drivers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the SH timers use a roughly identical structure for platform data,
which presently is broken out for each block. Consolidate all of these
definitions, as there is no reason for them to be broken out in the first
place.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds TMU platform data for sh7722. Only clockevent
mode is enabled for now, clocksource requires this patch:
"clocksource: setup mult_orig in clocksource_enable()"
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds MTU2 platform data for the following cpus:
- sh7201 (3/5 channels)
- sh7203/sh7263 (2/4 channels)
- sh7206 (3/5 channels)
- MXG (3/5 channels)
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Impact: cleanup
Convert the last remaining users to struct irq_chip and remove the
define.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch adds 16-bit cmt platform data for the following cpus:
- sh7619 (2 channels)
- sh7203/sh7263 (2 channels)
- sh7206 (2 channels)
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The sh architecture has some code in the .text.init section, but it
does not reference that section in its linker scripts.
This change moves this code from the .text.init section to the
.init.text section, which is presumably where it belongs.
Signed-off-by: Tim Abbott <tabbott@mit.edu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Use plat_early_device_setup() to register Early Platform Data
for SuperH Mobile processors.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds uio_pdrv_genirq support for the VEU.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds uio_pdrv_genirq support for the VPU.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the SH-Mobile I2C controller on the SH7724.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH-Mobile R2R CPU.
Based on Rev 0.11 of the initial SH7724 hardware manual.
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This corrects a race with the PHY RST bit not being set properly if the
PLL status changes right before timeout. This resulted in it potentially
failing even if the device came up in time.
Special thanks to Mr. Juha Leppanen and Iwamatsu-san for reporting this
out and reviewing it.
Reported-by: Juha Leppanen <juha_motorsportcom@luukku.com>
Reviewed-by: Nobuhiro Iwamatsu <iwamatsu.nobuhiro@renesas.com>
Tested-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Kuninori Morimoto <morimoto.kuninori@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were a number of issues with the DSP context save/restore code,
mostly left-over relics from when it was introduced on SH3-DSP with
little follow-up testing, resulting in things like task_pt_dspregs()
referencing incorrect state on the stack.
This follows the MIPS convention of tracking the DSP state in the
thread_struct and handling the state save/restore in switch_to() and
finish_arch_switch() respectively. The regset interface is also updated,
which allows us to finally be rid of task_pt_dspregs() and the special
cased task_pt_regs().
Signed-off-by: Michael Trimarchi <michael@evidence.eu.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Forcing direct-mapped worked on certain older 2-way set associative
parts, but was always error prone on 4-way parts. As these are the
norm these days, there is not much point in continuing to support this
mode. Most of the folks that used direct-mapped mode generally just
wanted writethrough caching in the first place..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
