Fix intelfb trying to free a non-existent resource in its error path.
Signed-off-by: Antonino Daplas <adaplas@pol.net>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The g5 thermal control for liquid cooled machines has a small bug, when
the temperatures gets too high, it boosts all fans to the max, but
incorrectly sets the liquids pump to the min instead of the max speed,
thus causing the overtemp condition not to clear and the machine to shut
down after a while. This fixes it to set the pumps to max speed instead.
This problem might explain some of the reports of random shutdowns that
some g5 users have been reporting in the past.
Many thanks to Marcus Rothe for spending a lot of time trying various
patches & sending log logs before I found out that typo. Note that
overtemp handling is still not perfect and the machine might still
shutdown, that patch should reduce if not eliminate such occcurences in
"normal" conditions with high load. I'll implement a better handling
with proper slowing down of the CPUs later.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The CPM2 interrupt handler does not return success to the IRQ subsystem, which
causes it to kill the IRQ line after 100,000 interrupts.
Signed-off-by: Edson Seabra <Edson.Seabra@cyclades.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since we don't restore the volatile registers in the syscall exit
path, we need to make sure we don't leak any potentially interesting
values from the kernel to userspace. This was already the case for
all except r11. This makes it use r11 for an MSR value, so r11 will
have an (uninteresting) MSR value in it on return to userspace.
Signed-off-by: Paul Mackerras <paulus@samba.org>
When mixing -olock and -onolock mounts on the same client, we have to
check that fl->fl_u.nfs_fl.owner is set before dereferencing it.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
gss_create_upcall() should not error just because rpc.gssd closed the
pipe on its end. Instead, it should requeue the pending requests and then
retry.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
Ensure we call unmap_mapping_range() and sync dirty pages to disk before
doing an NFS direct write.
Signed-off-by: Trond Myklebust <Trond.Myklebust@netapp.com>
I had thought that keeping the reported tail level clearly different
from the module name was a good idea, but I've changed my mind.
'raid5' is better and probably less confusing than 'RAID-5'.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is just a basic cleanup. No change in functionality.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Skip the memory 0xb50 to 0x1000 during "ethtool -t" memory test.
Overwriting memory in this region can cause ASF problems.
Update version and release date.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tw32_f() function (register write with immediate read flush) can
hang when used on some registers to switch clock frequencies and
power. A new tw32_wait_f() is added for such registers with the
delay before the read and after the read.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add some missing workarounds in tg3_set_power_state():
1. Workaround to prevent overdrawing current on 5714.
2. Do not power down 5700's PHY because of hw limitation.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Locate the pdev_peer for dual port 5714 NIC devices in addition to
5704 devices. The name is also changed to tg3_find_peer() from
tg3_find_5704_peer(). It is also necessary to call netdev_priv() to
get to the peer's private tg3 structure.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On sparc and sparc64, the rtc driver doesn't compile with PCI support
disabled.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make sctp_writeable() use sk_wmem_alloc rather than sk_wmem_queued to
determine the sndbuf space available. It also removes all the modifications
to sk_wmem_queued as it is not currently used in SCTP.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we insert a new xfrm_state which potentially
subsumes an existing one, make sure all cached
bundles are flushed so that the new SA is used
immediately.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Nicolas Pitre
Strictly speaking, the NPTL kernel helpers are required for pre ARMv6
only. They are available on ARMv6+ as well for obvious compatibility
reasons. However there are cases where extra memory barriers are needed
when using an SMP ARMv6 machine but not on pre-ARMv6.
This patch adds a memory barrier kernel helper that glibc can use as
needed for pre-ARMv6 binaries to be forward compatible with an SMP
kernel on ARMv6, as well as the necessary dmb instructions to the
cmpxchg helper.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Acked-by: Daniel Jacobowitz <dan@codesourcery.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The route expiration time is stored in rt6i_expires in jiffies.
The argument of rt6_route_add() for adding a route is not the
expiration time in jiffies nor in clock_t, but the lifetime
(or time left before expiration) in clock_t.
Because of the confusion, we sometimes saw several strange errors
(FAILs) in TAHI IPv6 Ready Logo Phase-2 Self Test.
The symptoms were analyzed by Mitsuru Chinen <CHINEN@jp.ibm.com>.
Signed-off-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
A typo caused some bridged IPv6 packets to get dropped randomly,
as reported by Sebastien Chaumontet. The patch below fixes this
(using skb->nh.raw instead of raw) and also makes the jumbo packet
length checking up-to-date with the code in
net/ipv6/exthdrs.c::ipv6_hop_jumbo.
Signed-off-by: Bart De Schuymer <bdschuym@pandora.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
I reported a problem and gave hints to the solution, but nobody seemed
to react. So I prepared a patch against 2.6.14.4.
Tested on 2.6.14.4 with "ip monitor addr" and with the program
attached, while adding and removing IPv6 address. Both programs didn't
receive any messages. Tested 2.6.14.4 + this patch, and both programs
received add and remove messages.
Signed-off-by: Kristian Slavov <kristian.slavov@nomadiclab.com>
Acked-by: Jamal Hadi salim <hadi@cyberus.ca>
ACKed-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
IP6_NF_TARGET_NFQUEUE depends on IP6_NF_IPTABLES, not IP_NF_IPTABLES.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noticed by Phil Oester, the GRE NAT protocol helper is initialized
before the NAT core, which makes registration fail.
Change the linking order to make NAT be initialized first.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Tuner 100 is the TUNER_PHILIPS_FMD1216ME_MK3, not TUNER_ABSENT. This
was causing the tuner module to be skipped, and rendered boards with this
value in the eeprom (like the HVR1100) unable to tune
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@brturbo.com.br>
Also renamed in honor of Portland being snowed in and everybody sliding
around on the highways like greased pumpkins.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This (and the three subsequent patches) is working well on OMAP H4 with
2.6.15-rc4 kernel and passes the LTP fs test.
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a typo which breaks radeon drm compilation with gcc 2.95.3.
The offending line was added back in 2.6.11-rc3, but was harmless
back then. A recent addition nearby changed it into a compilation
breaker: commit 281ab031a8.
The doubled semi-colon ends up being an empty instruction, and the
variable declaration thus ends up being in the middle of "code".
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mark M. Hoffman <mhoffman@lightlink.com>
Cc: Paul Mackerras <paulus@samba.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
UML skas0 stub has been miscompiling for many people (incidentally not
the authors), depending on the used GCC versions.
I think (and testing on some GCC versions shows) this patch avoids the
fundamental issue which is behind this, namely gcc using the stack when
we have just replaced it, behind gcc's back. The remapping and storage
of the return value is hidden in a blob of asm, hopefully giving gcc no
room for creativity.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
So you may have seen the miniconfig stuff wander by, which means that my
build script exits if there's a .config error, and we have this:
fs/Kconfig:1749:warning: 'select' used by config symbol 'CIFS_UPCALL'
refer to undefined symbol 'CONNECTOR'
This makes it shut up.
Signed-off-by: Rob Landley <rob@landley.net>
[ Verified it makes sense. ]
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
The current UML build assumes that on x86-64 systems, /lib is a symlink
to /lib64, but in some distributions (like PLD and CentOS) they are
separate directories, so the 64 bit library loader isn't found. This
patch inserts /lib64 at the start of the rpath on x86-64 UML builds.
Signed-off-by: Rob Landley <rob@landley.net>
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Duplicated code - the patch adding it was probably applied twice without
enough care.
Signed-off-by: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Miquel van Smoorenburg <miquels@cistron.nl> forwarded me this fix to
resolve a deadlock condition that occurs due to the API change in
2.6.13+ kernels dropping the host locking when entering the error
handling. They all end up calling adpt_i2o_post_wait(), which if you
call it unlocked, might return with host_lock locked anyway and that
causes a deadlock.
Signed-off-by: Mark Salyzyn <aacraid@adaptec.com>
Cc: James Bottomley <James.Bottomley@steeleye.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When dpt_i2o is loaded first, i2o being loaded would cause it to call
pci_device_disable, thus breaking dpt_i2o's use of the device. Based on
similar usage of pci_disable_device in other drivers.
Signed-off-by: Ben Collins <bcollins@ubuntu.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
scsi_reap_target() was desgined to be called from any context.
However it must do a device_del() of the target device, which may only
be called from user context. Thus we have to reimplement
scsi_reap_target() via a workqueue.
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
