printk should use KERN_* levels.
CC: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch moves the subsystem ID and subsystem vendor ID check from probing
function to the PCI generic function by describing subsystem IDs in
pci_device_id table. This enables to add new PCI IDs to a device driver pci_ids
table at runtime by new_id file in sysfs pci driver tree.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removing two bugs to improve sensitivity for DiB7070 and Dib7000P with MT2266.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Here is a patch for Hauppage Nova-T-Stick and Nova-T-500 users. It
sets the MT2060 IF1 frequency according to the calibration values
stored in the EEPROM.
It is supposed to enhance the signal quality, but, hey, there is no
guarantee. Feedbacks would be much appreciated, to know whether it
deserves being applied.
Signed-off-by: Olivier DANET <odanet at caramail.com>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was a mistake in the way how to start the streaming in the dib0700. This patch fixes that.
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The attached patch solves all my vdr tuning problems on a dib7000p
nova-t stick as far as I could check within the last weekend.
It disables streaming while tuning, like that the number of faulty TS
packets is reduced.
Signed-off-by: Soeren Moch <Soeren.Moch@stud.uni-hannover.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Here's a roll-up which provides support for both this and the myTV.t.
Signed-off-by: Darren Salt <linux@youmustbejoking.demon.co.uk>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for WinTV Nova-T-CE driver
Signed-off-by: Tim Taubert <ttmails@gmx.de>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch fix autoserach in the Hauppauge NOVA-T 500.
Signed-off-by: Jose Alberto Reguero <jareguero@telefonica.net>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adding support for ASUS My Cinema U3000 Mini DVBT Tuner
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
Signed-off-by: Patrick Boettcher <pb@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Marcos Melero (marcosmelero at gmail.com) reported he could make
his dvb-t usb stick work with the af9005 driver by changing the device
ids (10b9:6000).
The stick is branded "Ansonic" (one of the brands of a spanish chain of
supermarkets) with no other identification of the model.
Since neither Marcos nor me know the OEM for the stick, in the attached
patch I used Ansonic for the ids/description.
Signed-off-by: Luca Olivetti <luca@ventoso.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Call analog_ops.standby during tda18271_set_params, to put the tda8295
in tri-state when tuning digital channels. Otherwise the tda8295 will
interfere with the signal coming from the tda18271 into the digital
demodulator.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Correctly set the atatch structures, enable IR, configure the
xc5000 tuner includes.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
xc5000: Small amount of cleanup and commenting, just for clarification.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
From Zhang: This an updated patch that adds analog support for
the xc5000 tuner driver. it was tested on a Pinnacle PCTV HD 800i
card (patches to follow).
Patch commited as-is, cleanup to follow ... Steve.
Signed-off-by: Chaogui Zhang <czhang1974@gmail.com>
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Parallel support was not working with the s5h1409 and the Pinnacle HD800i.
This patch fixes the demodulator driver and ensures that all existing
s5h1409 based products configure the demodulator correctly.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This module option variable is only handled within the file tda18271-fe.c -
Declare this variable as static.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If module option "cal" is set to 1, the ~22 sec rf tracking filter calibration
sequence will be invoked on startup. Otherwise, the calibration will take
place during the first tune.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Test RF_CAL_OK to see if we need to perform the RF tracking filter
calibration after returning from standby.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add function, tda18271_set_standby_mode.
During sleep, enter standby mode with slave tuner output enabled,
loop through on and xtal oscillator on.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If not it impacts on analog tuner quality.
Signed-off-by: Steven Toth <stoth@hauppauge.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We don't usually want to see the calibration debug messages, but sometimes
it is useful. Assign it to a separate debug mask.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Store last tuned frequency & bandwidth after successful tune.
Clean up tune functions -- remove pointer to tune function in
state structure, instead call tune function based on priv->id.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Always initialize registers during attach.
Perform IR Calibration during init if needed.
Perform RF Calibration during init if needed for C2, only.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
An earlier patch, "tda18271: fail table lookups if frequency is out of range"
broke analog support on certain hardware. This patch fixes that problem, by
allowing the RF_CAL byte to be set to the maximum value, in cases of the
frequency being out of range.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Store IF Frequency in a u16 instead of a u32. Multiply by 1000 before use.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow drivers to pass device-specific configuration parameters during attach.
If these parameters are omitted, default values will be used.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Move some common code to a new file to make this easier to look at.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Tested successfully with QAM256 digital cable.
Analog television is limping, needs more work.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
make set_analog_params function look consistent with set_params function
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Break out the following new functions from tda18271_tune:
tda18271_calc_bp_filter
tda18271_calc_km
tda18271_calc_rf_band
tda18271_calc_gain_taper
tda18271_calc_ir_measure
tda18271_calc_rf_cal
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We don't need to do a dbg_info during tda18271_attach anymore, since
the tda18271_get_id function will call dbg_info with the same information
and more.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
