Kevin Winchester reported a GART related direct rendering failure against
linux-next-20080611, which shows up via these log entries:
PCI: Using ACPI for IRQ routing
PCI: Cannot allocate resource region 0 of device 0000:00:00.0
agpgart: Detected AGP bridge 0
agpgart: Aperture conflicts with PCI mapping.
agpgart: Aperture from AGP @ e0000000 size 128 MB
agpgart: Aperture conflicts with PCI mapping.
agpgart: No usable aperture found.
agpgart: Consider rebooting with iommu=memaper=2 to get a good aperture.
instead of the expected:
PCI: Using ACPI for IRQ routing
agpgart: Detected AGP bridge 0
agpgart: Aperture from AGP @ e0000000 size 128 MB
Kevin bisected it down to this change in tip/x86/gart:
"x86: checking aperture size order".
agp check is using request_mem_region(), and could fail if e820 is reserved...
change it back to e820_any_mapped().
Reported-and-bisected-by: "Kevin Winchester" <kjwinchester@gmail.com>
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Tested-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
General Software writes their own VSA2 module for their version
of the Geode BIOS, which returns a different ID then the standard
VSA2. This was causing the framebuffer driver to break for most
GSW boards.
Signed-off-by: Jordan Crouse <jordan.crouse@amd.com>
Cc: tglx@linutronix.de
Cc: linux-geode@lists.infradead.org
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch uses the BOOTMEM_EXCLUSIVE for crashkernel reservation also for
i386 and prints a error message on failure.
The patch is still for 2.6.26 since it is only bug fixing. The unification
of reserve_crashkernel() between i386 and x86_64 should be done for 2.6.27.
Signed-off-by: Bernhard Walle <bwalle@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: <stable@kernel.org>
Booting 2.6.26-rc6 on my 486 DX/4 fails with a "BUG: Int 6"
(invalid opcode) and a kernel halt immediately after the
kernel has been uncompressed. The BUG shows EIP pointing
to an rdtsc instruction in native_read_tsc(), invoked from
native_sched_clock().
(This error occurs so early that not even the serial console
can capture it.)
A bisection showed that this bug first occurs in 2.6.26-rc3-git7,
via commit 9ccc906c97:
>x86: distangle user disabled TSC from unstable
>
>tsc_enabled is set to 0 from the command line switch "notsc" and from
>the mark_tsc_unstable code. Seperate those functionalities and replace
>tsc_enable with tsc_disable. This makes also the native_sched_clock()
>decision when to use TSC understandable.
>
>Preparatory patch to solve the sched_clock() issue on 32 bit.
>
>Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The core reason for this bug is that native_sched_clock() gets
called before tsc_init().
Before the commit above, tsc_32.c used a "tsc_enabled" variable
which defaulted to 0 == disabled, and which only got enabled late
in tsc_init(). Thus early calls to native_sched_clock() would skip
the TSC and use jiffies instead.
After the commit above, tsc_32.c uses a "tsc_disabled" variable
which defaults to 0, meaning that the TSC is Ok to use. Early calls
to native_sched_clock() now erroneously try to use the TSC on
!cpu_has_tsc processors, leading to invalid opcode exceptions.
My proposed fix is to initialise tsc_disabled to a "soft disabled"
state distinct from the hard disabled state set up by the "notsc"
kernel option. This fixes the native_sched_clock() problem. It also
allows tsc_init() to be simplified: instead of setting tsc_disabled = 1
on every error return, we just set tsc_disabled = 0 once when all
checks have succeeded.
I've verified that this lets my 486 boot again. I've also verified
that a Core2 machine still uses the TSC as clocksource after the patch.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Patrick McHardy reported a crash:
> > I get this oops once a day, its apparently triggered by something
> > run by cron, but the process is a different one each time.
> >
> > Kernel is -git from yesterday shortly before the -rc6 release
> > (last commit is the usb-2.6 merge, the x86 patches are missing),
> > .config is attached.
> >
> > I'll retry with current -git, but the patches that have gone in
> > since I last updated don't look related.
> >
> > [62060.043009] BUG: unable to handle kernel NULL pointer dereference at
> > 000001ff
> > [62060.043009] IP: [<c0102a9b>] __switch_to+0x2f/0x118
> > [62060.043009] *pde = 00000000
> > [62060.043009] Oops: 0002 [#1] PREEMPT
Vegard Nossum analyzed it:
> This decodes to
>
> 0: 0f ae 00 fxsave (%eax)
>
> so it's related to the floating-point context. This is the exact
> location of the crash:
>
> $ addr2line -e arch/x86/kernel/process_32.o -i ab0
> include/asm/i387.h:232
> include/asm/i387.h:262
> arch/x86/kernel/process_32.c:595
>
> ...so it looks like prev_task->thread.xstate->fxsave has become NULL.
> Or maybe it never had any other value.
Somehow (as described below) TS_USEDFPU is set but the fpu is not
allocated or freed.
Another possible FPU pre-emption issue with the sleazy FPU optimization
which was benign before but not so anymore, with the dynamic FPU allocation
patch.
New task is getting exec'd and it is prempted at the below point.
flush_thread() {
...
/*
* Forget coprocessor state..
*/
clear_fpu(tsk);
<----- Preemption point
clear_used_math();
...
}
Now when it context switches in again, as the used_math() is still set
and fpu_counter can be > 5, we will do a math_state_restore() which sets
the task's TS_USEDFPU. After it continues from the above preemption point
it does clear_used_math() and much later free_thread_xstate().
Now, at the next context switch, it is quite possible that xstate is
null, used_math() is not set and TS_USEDFPU is still set. This will
trigger unlazy_fpu() causing kernel oops.
Fix this by clearing tsk's fpu_counter before clearing task's fpu.
Reported-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
attached is a no-brainer that makes kernel correctly report
NR_BANKS for MCE. We are right now limited to NR_BANKS==6, but the
error message will use the available number of banks instead of the
defined maximum.
For a Nehalem based system it will print:
"MCE: warning: using only 9 banks"
while the correct message would be
"MCE: warning: using only 6 banks"
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jbarnes/pci-2.6:
PCI: fixup write combine comment in pci_mmap_resource
x86: PAT export resource_wc in pci sysfs
x86, pci-dma.c: don't always add __GFP_NORETRY to gfp
suspend-vs-iommu: prevent suspend if we could not resume
x86: pci-dma.c: use __GFP_NO_OOM instead of __GFP_NORETRY
pci, x86: add workaround for bug in ASUS A7V600 BIOS (rev 1005)
PCI: use dev_to_node in pci_call_probe
PCI: Correct last two HP entries in the bfsort whitelist
Recently (around 2.6.25) I've noticed that RTC no longer works for me. It
turned out this is because I use pnpacpi=off kernel option to work around
the parport_pc bugs. I always did so, but RTC used to work fine in the
past, and now it have regressed.
The patch fixes the problem by creating the platform device for the RTC
when PNP is disabled. This may also help running the PNP-enabled kernel
on an older PCs.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Cc: David Brownell <david-b@pacbell.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Adam Belay <ambx1@neo.rr.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Alessandro Suardi reported:
> Recently upgraded my FC6 desktop to Fedora 9; with the
> latest nautilus RPM updates my VNC session went nuts
> with nautilus pegging the CPU for everything that breathed.
>
> I now reverted to an earlier nautilus package, but during
> the peak CPU period my kernel spat this:
>
> [314185.623294] ------------[ cut here ]------------
> [314185.623414] WARNING: at kernel/lockdep.c:2658 check_flags+0x4c/0x128()
> [314185.623514] Modules linked in: iptable_filter ip_tables x_tables
> sunrpc ipv6 fuse snd_via82xx snd_ac97_codec ac97_bus snd_mpu401_uart
> snd_rawmidi via686a hwmon parport_pc sg parport uhci_hcd ehci_hcd
> [314185.623924] Pid: 12314, comm: nautilus Not tainted 2.6.26-rc5-git2 #4
> [314185.624021] [<c0115b95>] warn_on_slowpath+0x41/0x7b
> [314185.624021] [<c010de70>] ? do_page_fault+0x2c1/0x5fd
> [314185.624021] [<c0128396>] ? up_read+0x16/0x28
> [314185.624021] [<c010de70>] ? do_page_fault+0x2c1/0x5fd
> [314185.624021] [<c012fa33>] ? __lock_acquire+0xbb4/0xbc3
> [314185.624021] [<c012d0a0>] check_flags+0x4c/0x128
> [314185.624021] [<c012fa73>] lock_acquire+0x31/0x7d
> [314185.624021] [<c0128cf6>] __atomic_notifier_call_chain+0x30/0x80
> [314185.624021] [<c0128cc6>] ? __atomic_notifier_call_chain+0x0/0x80
> [314185.624021] [<c0128d52>] atomic_notifier_call_chain+0xc/0xe
> [314185.624021] [<c0128d81>] notify_die+0x2d/0x2f
> [314185.624021] [<c01043b0>] do_int3+0x1f/0x4d
> [314185.624021] [<c02f2d3b>] int3+0x27/0x2c
> [314185.624021] =======================
> [314185.624021] ---[ end trace 1923f65a2d7bb246 ]---
> [314185.624021] possible reason: unannotated irqs-off.
> [314185.624021] irq event stamp: 488879
> [314185.624021] hardirqs last enabled at (488879): [<c0102d67>]
> restore_nocheck+0x12/0x15
> [314185.624021] hardirqs last disabled at (488878): [<c0102dca>]
> work_resched+0x19/0x30
> [314185.624021] softirqs last enabled at (488876): [<c011a1ba>]
> __do_softirq+0xa6/0xac
> [314185.624021] softirqs last disabled at (488865): [<c010476e>]
> do_softirq+0x57/0xa6
>
> I didn't seem to find it with some googling, so here it is.
>
> I was incidentally ltracing that process to try and find out
> what was gulping down that much CPU (sorry, no idea
> whether ltrace and the WARNING happened at the same
> time or which came first) and:
Yeah, this is extremely likely to be the source of the warning.
The warning should be harmless, however.
> Box is my trusty noname K7-800, 512MB RAM; if there's
> anything else useful I might be able to provide, just ask.
It would be interesting to see where the int3 comes from. Too bad,
lockdep doesn't provide the register dump. The stacktrace also doesn't
go further than the int3(), I wonder if this int3 came from userspace?
The ltrace readme says "software breakpoints, like gdb", so I guess
this is the case. Yep, seems like it.
This looks relevant:
| commit fb1dac909d
| Author: Peter Zijlstra <a.p.zijlstra@chello.nl>
| Date: Wed Jan 16 09:51:59 2008 +0100
|
| lockdep: more hardirq annotations for notify_die()
I'm attaching a similarly-looking patch for this case (DO_VM86_ERROR),
though I suspect it might be missing for the other cases
(DO_ERROR/DO_ERROR_INFO) as well.
Reported-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This reverts commit 6e908947b4.
Németh Márton reported:
| there is a problem in 2.6.26-rc3 which was not there in case of
| 2.6.25: the CPU wakes up ~90,000 times per sec instead of ~60 per sec.
|
| I also "git bisected" the problem, the result is:
|
| 6e908947b4 is first bad commit
| commit 6e908947b4
| Author: Ingo Molnar <mingo@elte.hu>
| Date: Fri Mar 21 14:32:36 2008 +0100
|
| x86: fix ioapic bug again
the original problem is fixed by Maciej W. Rozycki in the tip/x86/apic
branch (confirmed by Márton), but those changes are too intrusive for
v2.6.26 so we'll go for the less intrusive (repeated) revert now.
Reported-and-bisected-by: Németh Márton <nm127@freemail.hu>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Mon, May 19, 2008 at 04:10:02PM -0700, Linus Torvalds wrote:
> It also causes these warnings on 32-bit PAE:
>
> AS arch/x86/kernel/head_32.o
> arch/x86/kernel/head_32.S: Assembler messages:
> arch/x86/kernel/head_32.S:225: Warning: left operand is a bignum; integer 0 assumed
> arch/x86/kernel/head_32.S:609: Warning: left operand is a bignum; integer 0 assumed
>
> and I do not see why (the end result seems to be identical).
Fix head_32.S gcc bignum warnings when CONFIG_PAE=y.
arch/x86/kernel/head_32.S: Assembler messages:
arch/x86/kernel/head_32.S:225: Warning: left operand is a bignum; integer 0 assumed
arch/x86/kernel/head_32.S:609: Warning: left operand is a bignum; integer 0 assumed
The assembler was stumbling over the 64-bit constant 0x100000000 in the
KPMDS #define.
Testing: a cmp(1) on head_32.o before and after shows the binary is unchanged.
Signed-off-by: Joe Korty <joe.korty@ccur.com
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Theodore Tso <tytso@mit.edu>
Cc: Gabriel C <nix.or.die@googlemail.com>
Cc: Keith Packard <keithp@keithp.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: "Siddha Suresh B" <suresh.b.siddha@intel.com>
Cc: bugme-daemon@bugzilla.kernel.org
Cc: airlied@linux.ie
Cc: "Barnes Jesse" <jesse.barnes@intel.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The checking 'if nmi_watchdog > 0' (ie NMI_NONE) is quite fast but it
has a side effect - it's taken even if nmi_watchdog = NMI_DISABLED.
Nowadays nmi_watchdog is set up to NMI_NONE by default so this condition
is properly taken most the time but we better show this explicitly.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If GART IOMMU is used on an AMD64 system, the northbridge registers
related to it should be restored during resume so that memory is not
corrupted. Make gart_resume() handle that as appropriate.
Ref. http://lkml.org/lkml/2008/5/25/96 and the following thread.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Starting with commit 8d4a430085 (x86:
cleanup PAT cpu validation) the PAT CPU feature flag is not cleared
anymore. Now the error message
"PAT enabled, but CPU feature cleared"
in pat_init() is misleading.
Furthermore the current code does not check for existence of the PAT
CPU feature flag if a CPU is whitelisted in validate_pat_support.
This patch clears pat_wc_enabled if boot CPU has no PAT feature flag
and adapts the paranoia check.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If PAT support is advertised it should just work. No errata known.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
more unification. Should cause no change in functionality.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
cpuid(0x05) provides extended information about MWAIT in EDX when bit
0 of ECX is set. Bit 4-7 of EDX determine whether MWAIT is supported
for C1. C1E enabled CPUs have these bits set to 0.
Based on an earlier patch from Andi Kleen.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simplify code: no need to do a cpuid(1) again. The cpuinfo structure
has all necessary information already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Rename the "MSR_K8_ENABLE_C1E" MSR to INT_PENDING_MSG, which is the
name in the data sheet as well. Move the C1E mask to the header file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
default_idle is selected in cpu_idle(), when no other idle routine is
selected. Select it in select_idle_routine() when mwait is not
selected.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently arch/x86/kernel/pci-dma.c always adds __GFP_NORETRY
to the allocation flags, because it wants to be reasonably
sure not to deadlock when calling alloc_pages().
But really that should only be done in two cases:
- when allocating memory in the lower 16 MB DMA zone.
If there's no free memory there, waiting or OOM killing is of no use
- when optimistically trying an allocation in the DMA32 zone
when dma_mask < DMA_32BIT_MASK hoping that the allocation
happens to fall within the limits of the dma_mask
Also blindly adding __GFP_NORETRY to the the gfp variable might
not be a good idea since we then also use it when calling
dma_ops->alloc_coherent(). Clearing it might also not be a
good idea, dma_alloc_coherent()'s caller might have set it
on purpose. The gfp variable should not be clobbered.
[ mingo@elte.hu: converted to delta patch ontop of previous version. ]
Signed-off-by: Miquel van Smoorenburg <miquels@cistron.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
need to call early_reserve_e820() to preallocate mptable for 32bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
... so it could fall back to normal numa and we'd reduce the impact of the
NUMAQ subarch.
NUMAQ depends on GENERICARCH
also decouple genericarch numa from acpi.
also make it fall back to bigsmp if apicid > 8.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
a multi-socket test-system with 3 or 4 ioapics, when 4 dualcore cpus or
2 quadcore cpus installed, needs to switch to bigsmp or physflat.
CPU apic id is [4,11] instead of [0,7], and we need to check max apic
id instead of cpu numbers.
also add check for 32 bit when acpi is not compiled in or acpi=off.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix:
arch/x86/kernel/built-in.o: In function `proc_nmi_enabled':
: undefined reference to `nmi_watchdog_default'
arch/x86/kernel/built-in.o: In function `native_smp_prepare_cpus':
: undefined reference to `nmi_watchdog_default'
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch does check if CPU is being recongnized
before call the unreserve(). Since enable_lapic_nmi_watchdog()
does have such a check the same is make sense here too
in a sake of code consistency (but nothing more).
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: mingo@redhat.com
Cc: hpa@zytor.com
Cc: macro@linux-mips.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
64bit mode bootstrap code does set nmi_watchdog to NMI_NONE
by default and doing the same on 32bit mode is safe too.
Such an action saves us from several #ifdef.
Btw, my previous commit
commit 19ec673ced
Author: Cyrill Gorcunov <gorcunov@gmail.com>
Date: Wed May 28 23:00:47 2008 +0400
x86: nmi - fix incorrect NMI watchdog used by default
did not fix the problem completely, moreover it
introduced additional bug - nmi_watchdog would be
set to either NMI_LOCAL_APIC or NMI_IO_APIC
_regardless_ to boot option if being enabled thru
/proc/sys/kernel/nmi_watchdog. Sorry for that.
Fix it too.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: mingo@redhat.com
Cc: hpa@zytor.com
Cc: macro@linux-mips.org
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch adds linked list of struct setup_data supported for i386.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch extracts the common part of head32.c and head64.c into head.c.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch reserves the EFI memory map with reserve_early(). Because EFI
memory map is allocated by bootloader, if it is not reserved by
reserved_early(), it may be overwritten through address returned by
find_e820_area().
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes early reserved highmem pages become reserved
pages. This can be used for highmem pages allocated by bootloader such
as EFI memory map, linked list of setup_data, etc.
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch clean up reserve_early() family functions by extracting the
common part of reserve_early(), free_early() and bad_addr() into
find_overlapped_early().
Signed-off-by: Huang Ying <ying.huang@intel.com>
Cc: andi@firstfloor.org
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If
fix == 0, aper_enabled == 1, gart_fix_e820 == 0
if (!fix && !aper_enabled)
return;
if (gart_fix_e820 && !fix && aper_enabled) {
if (e820_any_mapped(aper_base, aper_base + aper_size,
E820_RAM)) {
/* reserve it, so we can reuse it in second kernel */
printk(KERN_INFO "update e820 for GART\n");
add_memory_region(aper_base, aper_size, E820_RESERVED);
update_e820();
}
return;
}
/* different nodes have different setting, disable them all atfirst*/
we'll fall back here and disable all the settings, even when they were
all consistent.
What about this? (I hope it compiles...)
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hi!
void __init early_gart_iommu_check(void)
contains
for (num = 24; num < 32; num++) {
if (!early_is_k8_nb(read_pci_config(0, num, 3, 0x00)))
continue;
loop, with very similar loop duplicated in
void __init gart_iommu_hole_init(void)
. First copy of a loop seems to be buggy, too. It uses 0 as a "nothing
set" value, which may actually bite us in last_aper_enabled case
(because it may be often zero).
(Beware, it is hard to test this patch, because this code has about
2^8 different code paths, depending on hardware and cmdline settings).
Plus, the second loop does not check for consistency of
aper_enabled. Should it?
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
should use right shift
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Jürgen Mell reported an FPU state corruption bug under CONFIG_PREEMPT,
and bisected it to commit v2.6.19-1363-gacc2076, "i386: add sleazy FPU
optimization".
Add tsk_used_math() checks to prevent calling math_state_restore()
which can sleep in the case of !tsk_used_math(). This prevents
making a blocking call in __switch_to().
Apparently "fpu_counter > 5" check is not enough, as in some signal handling
and fork/exec scenarios, fpu_counter > 5 and !tsk_used_math() is possible.
It's a side effect though. This is the failing scenario:
process 'A' in save_i387_ia32() just after clear_used_math()
Got an interrupt and pre-empted out.
At the next context switch to process 'A' again, kernel tries to restore
the math state proactively and sees a fpu_counter > 0 and !tsk_used_math()
This results in init_fpu() during the __switch_to()'s math_state_restore()
And resulting in fpu corruption which will be saved/restored
(save_i387_fxsave and restore_i387_fxsave) during the remaining
part of the signal handling after the context switch.
Bisected-by: Jürgen Mell <j.mell@t-online.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Jürgen Mell <j.mell@t-online.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
iommu/gart support misses suspend/resume code, which can do bad stuff,
including memory corruption on resume. Prevent system suspend in case we
would be unable to resume.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Tested-by: Patrick <ragamuffin@datacomm.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix the math emulation that got broken with the recent lazy allocation of FPU
area. init_fpu() need to be added for the math-emulation path aswell
for the FPU area allocation.
math emulation enabled kernel booted fine with this, in the presence
of "no387 nofxsr" boot param.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Cc: hpa@zytor.com
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
for http://bugzilla.kernel.org/show_bug.cgi?id=10613
BIOS bug, APIC version is 0 for CPU#0! fixing up to 0x10. (tell your hw vendor)
v2: fix 64 bit compilation
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Gabriel C <nix.or.die@googlemail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
this way 32-bit is more similar to 64-bit, and smarter e820 and numa.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
It looks good to move bugs_64.c to cpu/bugs_64.c.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
on 64-bit we only get valid max_pfn_mapped after init_memory_mapping().
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
on 32-bit in head_32.S after initial page table is done, we get initial
max_pfn_mapped, and then kernel_physical_mapping_init will give us
a final one.
We need to use that to make sure find_e820_area will get valid addresses
for boot_map and for NODE_DATA(0) on numa32.
XEN PV and lguest may need to assign max_pfn_mapped too.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
make mptable to be consistent with acpi routing, so we could:
1. kexec kernel with acpi=off
2. work around BIOSes where acpi routing is working, but mptable is
not right, so can use kernel/kexec to start other OSes that don't have
good acpi support.
command line: update_mptable
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
we don't need to call memory_present that early.
numa and sparse will call memory_present later and might
even fail, it will call memory_present for the full range.
also for sparse it will call alloc_bootmem ... before we set up bootmem.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
iommu/gart support misses suspend/resume code, which can do bad stuff,
including memory corruption on resume. Prevent system suspend in case we
would be unable to resume.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Tested-by: Patrick <ragamuffin@datacomm.ch>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Update the UV address macros to better describe the
fields of UV physical addresses. Improve comments
in the header files. Add additional MMR definitions.
Signed-off-by: Jack Steiner <steiner@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
On Wed, 2008-05-28 at 04:47 +0200, Andi Kleen wrote:
> > So... why not just remove the setting of __GFP_NORETRY? Why is it
> > wrong to oom-kill things in this case?
>
> When the 16MB zone overflows (which can be common in some workloads)
> calling the OOM killer is pretty useless because it has barely any
> real user data [only exception would be the "only 16MB" case Alan
> mentioned]. Killing random processes in this case is bad.
>
> I think for 16MB __GFP_NORETRY is ok because there should be
> nothing freeable in there so looping is useless. Only exception would be the
> "only 16MB total" case again but I'm not sure 2.6 supports that at all
> on x86.
>
> On the other hand d_a_c() does more allocations than just 16MB, especially
> on 64bit and the other zones need different strategies.
Okay, so how about this then ?
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Introduce IRQx_VECTOR on 32-bit, so that #ifdef noise is kept
down. There should be no object code change.
[ mingo@elte.hu: merged to x86/irq not x86/i8259 due to x86/irq having
restructured the vector code into asm-x86/irq_vectors.h, which this
patch touches. ]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch implements PCI extended configuration space access for
AMD's Barcelona CPUs. It extends the method using CF8/CFC IO
addresses. An x86 capability bit has been introduced that is set for
CPUs supporting PCI extended config space accesses.
Signed-off-by: Robert Richter <robert.richter@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
on two node system (16g RAM) with numa config I got this crash:
get_memcfg_from_srat: assigning address to rsdp
RSD PTR v0 [ACPIAM]
ACPI: Too big length in RSDT: 92
failed to get NUMA memory information from SRAT table
NUMA - single node, flat memory mode
Node: 0, start_pfn: 0, end_pfn: 153
Setting physnode_map array to node 0 for pfns:
0
...
Pid: 0, comm: swapper Not tainted 2.6.26-rc4 #4
[<80b41289>] hlt_loop+0x0/0x3
[<8011efa0>] ? alloc_remap+0x50/0x70
[<8079e32e>] alloc_node_mem_map+0x5e/0xa0
[<8012e77b>] ? printk+0x1b/0x20
[<80b590f6>] free_area_init_node+0xc6/0x470
[<80b588fc>] ? __alloc_bootmem_node+0x2c/0x50
[<80b58ad8>] ? find_min_pfn_for_node+0x38/0x70
[<8012e77b>] ? printk+0x1b/0x20
[<80b597c4>] free_area_init_nodes+0x254/0x2d0
[<80b544d7>] zone_sizes_init+0x97/0xa0
[<80b48a03>] setup_arch+0x383/0x530
[<8012e77b>] ? printk+0x1b/0x20
[<80b41aa4>] start_kernel+0x64/0x350
[<80b412d8>] i386_start_kernel+0x8/0x10
=======================
this patch increases the acpi table limit to 32.
Also match early_ioremap() with early_iounmap().
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
reserve early numa kva, so it will not clash with new RAMDISK
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
introduce init_pg_table_start, so xen PV could specify the value.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Create a separate centaur_64.c file in the cpu/ dir for
the useful parts to live in.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Create a separate intel_64.c file in the cpu/ dir for
the useful parts to live in.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Create a separate amd_64.c file in the cpu/ dir for
the useful parts to live in.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
arch/x86/kernel/mmconf-fam10h_64.c is missing the prototypes, which
are decalred in arch/x86/kernel/setup_64.c. Move the prototypes and
the inline stubs to the appropriate header file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The commit
commit 4b82b27770
Author: Cyrill Gorcunov <gorcunov@gmail.com>
Date: Sat May 24 19:36:35 2008 +0400
set nmi_watchdog to NMI_IO_APIC as by default. This causes hangs on some
machines with buggy watchdogs. Fix it - i.e. restore old behaviour.
Thanks to Sitsofe Wheeler and Adrian Bunk for catching the problem
and Maciej W. Rozycki for explanation what is going on there.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
CC: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Some small cleanups for aperture_64.c; they should not really change
any code.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
remove extra -1 in reseve_early calling
panic if can not find space for new RAMDISK
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add pte_flags() to extract the flags from a pte. This is a special
case of pte_val() which is only guaranteed to return the pte's flags
correctly; the page number may be corrupted or missing.
The intent is to allow paravirt implementations to return pte flags
without having to do any translation of the page number (most notably,
Xen).
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since cpu_online_map is touched (by for_each_online_cpu)
at moment when cpu_callin_map is already filled up we can
get rid of its checking at all
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: hpa@zytor.com
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
apic_write_around will be expanded to apic_write in 64bit mode
anyway. Only a few CPUs (well, old CPUs to be precise) requires
such an action. In general it should not hurt and could be cleaned
up for apic_write (just in case)
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: hpa@zytor.com
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
traps_32.c already holds these functions so do the same for traps_64.c
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: hpa@zytor.com
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make 64bit die_nmi() to produce the same message as 32bit mode has
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: hpa@zytor.com
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
By slightly changing 32bit mode die_nmi() we may unify the
interface and make it common for both (32/64bit) modes
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: hpa@zytor.com
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
UP builds with LOCAL_APIC=y and IO_APIC=n fail with a missing
reference to mp_bus_not_pci. Distangle the mpparse code some more and
move the ioapic specific bus check into a separate function.
This code needs sume urgent un#ifdef surgery all over the place.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This pushes the lock a fair way down and the final kill looks like it
should be an easy project for someone who wants to have a shot at it.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: mingo@redhat.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
and make e820_mark_nosave_regions to take limit_pfn to use max_low_pfn
for 32bit and end_pfn for 64bit
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Sitsofe Wheeler reported boot problems on linux-next.
It looks like the same issue as found by Soeren Sandman in 7575217f656a93,
"x86: initialize all fields of mp_irqs[mp_irq_entries]".
But his fix is also not complete, as dstapic is used before it assigned.
Reported-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Bisected-by: Sitsofe Wheeler <sitsofe@yahoo.com>
Signed-off-by: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit "x86: make config_irqsrc not MPspec specific" introduced some uses
of uninitialized fields in mp_config_acpi_legacy_irqs(). I need the
following patch to get sched-devel/master to boot.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
the new output is:
MPTABLE: OEM ID: SUN
MPTABLE: Product ID: 4600 M2
MPTABLE: APIC at: 0x
instead of it all in one line with <6> and double Product ID...
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
use find_e820_area to find addess for new RAMDISK, instead of using ram blindly
also print out low ram and bootmap info
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add to the kernels boot memory map 'memmap' entries found in
the EFI memory descriptors passed in from the BIOS.
On EFI systems, up to E820MAX == 128 memory map entries can
be passed via the legacy E820 interface (limited by the size
of the 'zeropage'). These entries can be duplicated in the
EFI descriptors also passed from the BIOS, and possibly more
entries passed by the EFI interface, which does not have the
E820MAX limit on number of memory map entries.
This code doesn't worry about the likely duplicate, overlapping
or (unlikely) conflicting entries between the EFI map and the
E820 map. It just dumps all the EFI entries into the memmap[]
array (which already has the E820 entries) and lets the existing
routine sanitize_e820_map() sort the mess out.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Elaborate on the comment for sanitize_e820_map(), epxlaining more what
it does, what it inputs, and what it returns. Rearrange the placement of
this comment to fit kernel conventions, before the routine's code rather
than buried inside it.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The map size counter passed into, and back out of, sanitize_e820_map(),
was an eight bit type (char or u8), as derived from its origins in
legacy BIOS E820 structures. This patch changes that type to an 'int',
to allow this sanitize routine to also be used on larger maps (larger
than the 256 count that fits in a char). The legacy BIOS E820 interface
of course does not change; that remains at 8 bits for this count, holding
up to E820MAX == 128 entries. But the kernel internals can handle more
when those additional memory map entries are passed from the BIOS via
EFI interfaces.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Extend internal boot time memory tables to allow for up to
three entries per node, which may be larger than the 128 E820MAX
entries handled by the legacy BIOS E820 interface. The EFI
interface, if present, is capable of passing memory map
entries for these larger node counts.
This patch requires an earlier patch that rewrote code depending
on these array sizes from using E820MAX explicitly to size loops,
to instead using ARRAY_SIZE() of the applicable array.
Another patch following this one will provide the code to pick
up additional memory entries passed via the EFI interface from
the BIOS and insert them in the following, now enlarged, arrays.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch is motivated by a subsequent patch which will allow for more
memory map entries on EFI supported systems than can be passed via the x86
legacy BIOS E820 interface. The legacy interface is limited to E820MAX ==
128 memory entries, and that "E820MAX" manifest constant was used as the
size for several arrays and loops over those arrays.
The primary change in this patch is to change code loop sizes over those
arrays from using the constant E820MAX, to using the ARRAY_SIZE() macro
evaluated for the array being looped. That way, a subsequent patch can
change the size of some of these arrays, without breaking this code.
This patch also adds a parameter to the sanitize_e820_map() routine,
which had an implicit size for the array passed it of E820MAX entries.
This new parameter explicitly passes the size of said array. Once again,
this will allow a subsequent patch to change that array size for some
calls to sanitize_e820_map() without breaking the code.
As part of enhancing the sanitize_e820_map() interface this way, I further
combined the unnecessarily distinct x86_32 and x86_64 declarations for
this routine into a single, commonly used, declaration.
This patch in itself should make no difference to the resulting kernel
binary.
[ mingo@elte.hu: merged to -tip ]
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Standardize a few pointer declarations to not have the
extra space after the '*' character.
Signed-off-by: Paul Jackson <pj@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
disable the noisy print out.
also use the one the less spare mtrr reg.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
there is a typo in the mask value, need to remove that extra 0,
to avoid 4bit clearing.
Signed-off-by: Yinghal Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
otherwise fixed MTRR for family 10h may not be changed.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Loop through mtrr chunk_size and gran_size from 1M to 2G to find out
the optimal value so user does not need to add mtrr_chunk_size and
mtrr_gran_size to the kernel command line.
If optimal value is not found, print out all list to help select less
optimal value.
Add mtrr_spare_reg_nr= so user could set 2 instead of 1, if the card
need more entries.
v2: find the one with more spare entries
v3: fix hole_basek offset
v4: tight the compare between range and range_new
loop stop with 4g
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Gabriel C <nix.or.die@googlemail.com>
Cc: Mika Fischer <mika.fischer@zoopnet.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
v9: address format change requests by Ingo
more case handling in range_to_var_with_hole
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
v2: process hole then end_pfn
fix update_memory_range with whole cover comparing
Signed-off-by: Yinghai Lu <yinghai.lu@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
converting MTRR layout from continous to discrete, some time could run out of
MTRRs. So add gran_sizek to prevent that by dumpping small RAM piece less than
gran_sizek.
previous trimming only can handle highest_pfn from mtrr to end_pfn from e820.
when have more than 4g RAM installed, there will be holes below 4g. so need to
check ram below 4g is coverred well.
need to be applied after
[PATCH] x86: mtrr cleanup for converting continuous to discrete layout v7
Signed-off-by: Yinghai Lu <yinghai.lu@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
some BIOS like to use continus MTRR layout, and X driver can not add
WB entries for graphical cards when 4g or more RAM installed.
the patch will change MTRR to discrete.
mtrr_chunk_size= could be used to have smaller continuous block to hold holes.
default is 256m, could be set according to size of graphics card memory.
mtrr_gran_size= could be used to send smallest mtrr block to avoid run out of MTRRs
v2: fix -1 for UC checking
v3: default to disable, and need use enable_mtrr_cleanup to enable this feature
skip the var state change warning.
remove next_basek in range_to_mtrr()
v4: correct warning mask.
v5: CONFIG_MTRR_SANITIZER
v6: fix 1g, 2g, 512 aligment with extra hole
v7: gran_sizek to prevent running out of MTRRs.
v8: fix hole_basek caculation caused when removing next_basek
gran_sizek using when basek is 0.
need to apply
[PATCH] x86: fix trimming e820 with MTRR holes.
right after this one.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The x86_64 code has centralized the memory setup code in
e820_64.c. This patch copies that approach to i386:
- early_param("mem", ...) parsing is moved from
setup_32.c to e820_32.c.
- setup_memory_map() and finish_e820_parsing() are
factored out from setup_arch(), and declarations
are added to e820_32.h.
- print_memory_map() is made static and removed from
e820_32.h.
- user_defined_memmap is marked as __initdata.
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kernel/cpu/mtrr/generic.c:216:12: warning: symbol 'lo' shadows an earlier one
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Remove the not longer used handlers for reserved vectors.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Just moved trailing statements to the next line, removed space before
open/close parenthesis, wrapped long lines.
Signed-off-by: Miklos Vajna <vmiklos@frugalware.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We should better use already defined flags from processor-flags.h instead
of defining own ones
[>>> object code check >>>]
original
md5sum: 9cfa6dbf045a046bb5dfb85f8bcfe8c4 arch/x86/kernel/head_64.o
text data bss dec hex filename
37361 4432 8192 49985 c341 arch/x86/kernel/head_64.o
patched
md5sum: 9cfa6dbf045a046bb5dfb85f8bcfe8c4 arch/x86/kernel/head_64.o
text data bss dec hex filename
37361 4432 8192 49985 c341 arch/x86/kernel/head_64.o
[<<< object code check <<<]
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch contains the following cleanups:
- make the following needlessly global code static:
- dma_alloc_pages()
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
arch/x86/kernel/mmconf-fam10h_64.c is missing the prototypes, which
are decalred in arch/x86/kernel/setup_64.c. Move the prototypes and
the inline stubs to the appropriate header file.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
sparse mutters:
arch/x86/kernel/vsmp_64.c:126:5: warning: symbol 'is_vsmp_box' was not declared. Should it be static?
arch/x86/kernel/vsmp_64.c:145:13: warning: symbol 'vsmp_init' was not declared. Should it be static?
Include the appropriate headers.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/tsc_64.c:245:13: warning: constant 0x100000000 is so big it is long
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
LAPIC interrupts, which don't go through the generic interrupt handling
code, aren't accounted for in /proc/stat. Hence this patch adds a
mechanism architectures can use to accordingly adjust the statistics.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
.. allowing it to be write-protected just as other read-only data
under CONFIG_DEBUG_RODATA.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-tip:
x86: prevent PGE flush from interruption/preemption
x86: use explicit copy in vdso_gettimeofday()
namespacecheck: automated fixes
x86/xen: fix arbitrary_virt_to_machine()
x86: don't read maxlvt before checking if APIC is mapped
x86: disable TSC for sched_clock() when calibration failed
x86: distangle user disabled TSC from unstable
x86: fix setup of cyc2ns in tsc_64.c
The leftovers of the i8259 unification have nothing to do with i8259
at all. They contain interrupt init code and the i8259_xx name is just
misleading now.
Rename them to irqinit_32/64.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove #ifdefs where the only difference is formatting of comments.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: macro@ds2.pg.gda.pl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove #ifdefs around includes; including too much should be always
safe.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: macro@ds2.pg.gda.pl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make conversion of i8259 very mechanical -- i8259 was generated by
diff -D, with too different parts left in i8259_32 and
i8259_64.c. Only "by hand" changes were removal of #ifdef from middle
of the comment (prevented compilation) and removal of one static to
allow splitting into files.
Of course, it will need some cleanups now, and those will follow.
Signed-of-by: Pavel Machek <pavel@suse.cz>
The leftovers of the i8259 unification have nothing to do with i8259
at all. They contain interrupt init code and the i8259_xx name is just
misleading now.
Rename them to initirq_32/64.c
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove #ifdefs where the only difference is formatting of comments.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: macro@ds2.pg.gda.pl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Remove #ifdefs around includes; including too much should be always
safe.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Cc: macro@ds2.pg.gda.pl
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A check for unmapped apic was added before reading maxlvt but the early
read of maxlvt wasn't removed.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Cc: Andi Kleen <ak@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
When the TSC calibration fails then TSC is still used in
sched_clock(). Disable it completely in that case.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
tsc_enabled is set to 0 from the command line switch "notsc" and from
the mark_tsc_unstable code. Seperate those functionalities and replace
tsc_enable with tsc_disable. This makes also the native_sched_clock()
decision when to use TSC understandable.
Preparatory patch to solve the sched_clock() issue on 32 bit.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the TSC is calibrated against the PIT due to the nonavailability
of PMTIMER/HPET or due to SMI interference then the setup of the per
CPU cyc2ns variables is skipped. This is unlikely to happen but it
would definitely render sched_clock() unusable.
This was introduced with commit 53d517cdba
x86: scale cyc_2_nsec according to CPU frequency
Update the per CPU cyc2ns variables in all exit pathes of tsc_calibrate.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Unconditionally enable PAT support on Centaur and Transmeta CPUs.
All known models that advertise PAT have no known errata.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
[PATCH] return to old errno choice in mkdir() et.al.
[Patch] fs/binfmt_elf.c: fix wrong return values
[PATCH] get rid of leak in compat_execve()
[Patch] fs/binfmt_elf.c: fix a wrong free
[PATCH] avoid multiplication overflows and signedness issues for max_fds
[PATCH] dup_fd() part 4 - race fix
[PATCH] dup_fd() - part 3
[PATCH] dup_fd() part 2
[PATCH] dup_fd() fixes, part 1
[PATCH] take init_files to fs/file.c
The longrun cpufreq module reports a false minimum frequency 3MHz on
300-600MHz Crusoe processor. This may be due to a calculation bug
in the module.
Original patch from Kaz Sasayama <kazssym@hypercore.co.jp>
submitted as http://bugs.debian.org/468149 patch ported to x86
Cc: Kaz Sasayama <kazssym@hypercore.co.jp>
Signed-off-by: maximilian attems <max@stro.at>
Signed-off-by: Dave Jones <davej@redhat.com>
The most common error with powernow-k8 is an ACPI _PSS error
caused either by failure to load the ACPI processor module
or a bad parse of the _PSS object. Make the error message
returned to the user in these situations more straightforward
and easier to understand.
-Mark Langsdorf
Operating System Research Center
AMD
Signed-off-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Dave Jones <davej@redhat.com>
The previous revert of 0c07ee38c9 left
out the mwait disable condition for AMD family 10H/11H CPUs.
Andreas Herrman said:
It depends on the CPU. For AMD CPUs that support MWAIT this is wrong.
Family 0x10 and 0x11 CPUs will enter C1 on HLT. Powersavings then
depend on a clock divisor and current Pstate of the core.
If all cores of a processor are in halt state (C1) the processor can
enter the C1E (C1 enhanced) state. If mwait is used this will never
happen.
Thus HLT saves more power than MWAIT here.
It might be best to switch off the mwait flag for these AMD CPU
families like it was introduced with commit
f039b75471 (x86: Don't use MWAIT on AMD
Family 10)
Re-add the AMD families 10H/11H check and disable the mwait usage for
those.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Vegard Nossum reports:
| powertop shows between 200-400 wakeups/second with the description
| "<kernel IPI>: Rescheduling interrupts" when all processors have load (e.g.
| I need to run two busy-loops on my 2-CPU system for this to show up).
|
| The bisect resulted in this commit:
|
| commit 0c07ee38c9
| Date: Wed Jan 30 13:33:16 2008 +0100
|
| x86: use the correct cpuid method to detect MWAIT support for C states
remove the functional effects of this patch and make mwait unconditional.
A future patch will turn off mwait on specific CPUs where that causes
power to be wasted.
Bisected-by: Vegard Nossum <vegard.nossum@gmail.com>
Tested-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The user_regset_view table for the 32-bit regsets on the 64-bit build had
the wrong sizes for the FP regsets. This bug had no user-visible effect
(just on kernel modules using the user_regset interfaces and the like).
But the fix is trivial and risk-free.
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix this symbol export problem:
Building modules, stage 2.
MODPOST 193 modules
ERROR: "csum_partial" [fs/reiserfs/reiserfs.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
This is due to a known weakness of symbol exports: if a symbol's
only in-core user is an EXPORT_SYMBOL from a lib-y section, the
symbol is not linked in.
The solution is to move the export to x8664_ksyms_64.c - but the real
solution would be to fix kbuild.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
arch/x86/kernel/setup_64.c:954: warning: passing argument 2 of 'set_bit' from incompatible pointer type
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After resume on a 2cpu laptop, kernel builds collapse with a sed hang,
sh or make segfault (often on 20295564), real-time signal to cc1 etc.
Several hurdles to jump, but a manually-assisted bisect led to -rc1's
d2bcbad5f3 x86: do not zap_low_mappings
in __smp_prepare_cpus. Though the low mappings were removed at bootup,
they were left behind (with Global flags helping to keep them in TLB)
after resume or cpu online, causing the crashes seen.
Reinstate zap_low_mappings (with local __flush_tlb_all) for each cpu_up
on x86_32. This used to be serialized by smp_commenced_mask: that's now
gone, but a low_mappings flag will do. No need for native_smp_cpus_done
to repeat the zap: let mem_init zap BSP's low mappings just like on UP.
(In passing, fix error code from native_cpu_up: do_boot_cpu returns a
variety of diagnostic values, Dprintk what it says but convert to -EIO.
And save_pg_dir separately before zap_low_mappings: doesn't matter now,
but zapping twice in succession wiped out resume's swsusp_pg_dir.)
That worked well on the duo and one quad, but wouldn't boot 3rd or 4th
cpu on P4 Xeon, oopsing just after unlock_ipi_call_lock. The TLB flush
IPI now being sent reveals a long-standing bug: the booting cpu has its
APIC readied in smp_callin at the top of start_secondary, but isn't put
into the cpu_online_map until just before that unlock_ipi_call_lock.
So native_smp_call_function_mask to online cpus would send_IPI_allbutself,
including the cpu just coming up, though it has been excluded from the
count to wait for: by the time it handles the IPI, the call data on
native_smp_call_function_mask's stack may well have been overwritten.
So fall back to send_IPI_mask while cpu_online_map does not match
cpu_callout_map: perhaps there's a better APICological fix to be
made at the start_secondary end, but I wouldn't know that.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The latest rev of Intel doc AP-485 details a new cache
descriptor that we don't yet support.
A 6MB 24-way assoc L2 cache.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
use per_cpu for per CPU data.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cleanup gart handling on amd64 a bit: move common code into
enable_gart_translation , and use symbolic register names where
appropriate.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
we can use free_bootmem() directly.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
1. use symbolic register names where appropriate.
2. num to bus or slot changing
3. handle for new opteron for bus other than 0
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
because we try to reserve dma32 early, so we have chance to get aperture
from 64M.
with some sequence aperture allocated from RAM, could become E820_RESERVED.
and then if doing a kexec with a big kernel that uncompressed size is above
64M we could have a range conflict with still using gart.
So allocate gart aperture from 512M instead.
Also change the fallback_aper_order to 5, because we don't have chance to get
2G or 4G aperture.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
some systems are using 32M for gart and agp when memory is less than 4G.
Kernel will reject and try to allcate another 64M that is not needed,
and we will waste 64M of perfectly good RAM.
this patch adds a workaround by checking aper_base/order between NB and
agp bridge. If they are the same, and memory size is less than 4G, it
will allow it.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
while looking at Rafael J. Wysocki's system boot log,
I found a funny printout:
Node 0: aperture @ de000000 size 32 MB
Aperture too small (32 MB)
AGP bridge at 00:04:00
Aperture from AGP @ de000000 size 4096 MB (APSIZE 0)
Aperture too small (0 MB)
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
...
agpgart: Detected AGP bridge 20
agpgart: Aperture pointing to RAM
agpgart: Aperture from AGP @ de000000 size 4096 MB
agpgart: Aperture too small (0 MB)
agpgart: No usable aperture found.
agpgart: Consider rebooting with iommu=memaper=2 to get a good aperture.
it means BIOS allocated the correct gart on the NB and AGP bridge, but
because a bug in the silicon (the agp bridge reports the wrong order,
it wants 4G instead) the kernel will reject that allocation.
Also, because the size is only 32MB, and we try to get another 64M for gart,
late fix_northbridge can not revert that change because it still reads
the wrong size from agp bridge.
So try to double check the order value from the agp bridge, before calling
aperture_valid().
[ mingo@elte.hu: 32-bit fix. ]
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move symbolic constants into gart.h, and use them instead of hardcoded
constant.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the 4KSTACKS related code to one place. This allows to un#ifdef
do_IRQ() and share the executed on stack for the stack overflow printk
and the softirq call.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add KERN_WARNING to the printk as this could not be done in the
original patch, which allegedly only moves code around.
Un#ifdef do_IRQ.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Previously the reporting printk would run on the process stack, which risks
overflow an already low stack. Instead execute it on the interrupt stack.
This makes it more likely for the printk to make it actually out.
It adds one not taken test/branch more to the interrupt path when
stack overflow checking is enabled. We could avoid that by duplicating
more code, but that seemed not worth it.
Based on an observation by Eric Sandeen.
v2: Fix warnings in some configs
Signed-off-by: Andi Kleen <andi@firstfloor.org>
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fixes the build error introduced by my FIRST_SYSTEM_VECTOR patch
Signed-off-by: Alan Mayer <ajm@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The SGI UV system needs several more system vectors than a vanilla
x86_64 system. Rather than burden the other archs with extra system
vectors that they don't use, change FIRST_SYSTEM_VECTOR to a variable,
so that it can be dynamic.
Signed-off-by: Alan Mayer <ajm@sgi.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The interrupt vector defines are copied 4 times around with minimal
differences. Move them all into asm-x86/irq_vectors.h
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Eliminate the 6 bank restriction in 64 bit mce reporting code. This
restriction is artificial (due to static creation of sysfs files) and 32
bit code does not have any such restriction.
This change helps in reporting the details of machine checks on a
machine check exception with errors in bank 6 and above on CPUs that
support those banks. Without the patch, machine check errors in those
banks are not reported.
We still have 128 (MCE_EXTENDED_BANK) bank restriction instead of max
256 supported in hardware. That is not changed in the patch below as it
will have some user level mcelog utility dependency, with bank 128 being
used for thermal reporting currently.
The patch below does not create sysfs control (bankNctl) for banks
higher than 6 as well. That needs some pre-cleanup in /sysfs mce layout,
removal of per cpu /sysfs entries for bankctl as they are really global
system level control today. That change will follow. This basic change
is critical to report the detailed errors on banks higher than 6.
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We have a lot of HPET quirks available which might force enable HPET
even when the BIOS does not enable it. Some of those quirks depend on
the command line option "hpet=force".
Andrew pointed out that hoping that the user will find out about this
boot option is not really helpful.
Emit a kernel info which informs the user about the "hpet=force" boot
option when we enter a quirk which depends on this option and the user
did not provide it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add quirk to allow forced usage of HPET on ATI SB400.
I stumbled over machines where HPET is enabled but not reported
by BIOS. This patch configures the HPET base address and makes
it known to the OS.
Signed-off-by: Andreas Herrmann <andreas.herrmann3@amd.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
While reading through the HPET code I realized that the
computation of .mult variables could be done with less
lines of code, resulting in a 1.6% text size saving
for hpet.o
So I propose the following patch, which applies against
today's Linus -git tree.
>From 0c6507e400e9ca5f7f14331e18f8c12baf75a9d3 Mon Sep 17 00:00:00 2001
From: Carlos R. Mafra <crmafra@ift.unesp.br>
Date: Mon, 5 May 2008 19:38:53 -0300
The computation of clocksource_hpet.mult
tmp = (u64)hpet_period << HPET_SHIFT;
do_div(tmp, FSEC_PER_NSEC);
clocksource_hpet.mult = (u32)tmp;
can be streamlined if we note that it is equal to
clocksource_hpet.mult = div_sc(hpet_period, FSEC_PER_NSEC, HPET_SHIFT);
Furthermore, the computation of hpet_clockevent.mult
uint64_t hpet_freq;
hpet_freq = 1000000000000000ULL;
do_div(hpet_freq, hpet_period);
hpet_clockevent.mult = div_sc((unsigned long) hpet_freq,
NSEC_PER_SEC, hpet_clockevent.shift);
can also be streamlined with the observation that hpet_period and hpet_freq are
inverse to each other (in proper units).
So instead of computing hpet_freq and using (schematically)
div_sc(hpet_freq, 10^9, shift) we use the trick of calling with the
arguments in reverse order, div_sc(10^6, hpet_period, shift).
The different power of ten is due to frequency being in Hertz (1/sec)
and the period being in units of femtosecond. Explicitly,
mult = (hpet_freq * 2^shift)/10^9 (before)
mult = (10^6 * 2^shift)/hpet_period (after)
because hpet_freq = 10^15/hpet_period.
The comments in the code are also updated to reflect the changes.
As a result,
text data bss dec hex filename
2957 425 92 3474 d92 arch/x86/kernel/hpet.o
3006 425 92 3523 dc3 arch/x86/kernel/hpet.o.old
a 1.6% reduction in text size.
Signed-off-by: Carlos R. Mafra <crmafra@ift.unesp.br>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To allow linker to catch sections overlapping we have to declare
them in appropriate order.
Signed-off-by: Cyrill Gorcunov <gorcunov@gmail.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The phys_cpu_present_map is an expected symbol in the SMP harness.
Unfortunately, x86 recently moved this and a few others to
kernel/setup.c where it doesn't quite work because voyager has to
define its own. Use CONFIG_X86_LOCAL_APIC to isolate these
definitions and fix up another area in setup.c where CONFIG_X86_SMP
should be used instead of CONFIG_SMP.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Cc: WANG Cong <xiyou.wangcong@gmail.com>
Cc: toralf.foerster@gmx.de
Cc: Mike Travis <travis@sgi.com>
Cc: Alexey Starikovskiy <astarikovskiy@suse.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Rene Herman reported:
> commit 8779f2fc3b
>
> "x86: don't try to allocate from DMA zone at first"
>
> breaks all of ISA DMA. Or all of ALSA ISA DMA at least. All
> ISA soundcards are silent following that commit -- no error
> messages, everything appears fine, just silence.
That patch is buggy. We had an implicit assumption that
dev = NULL for ISA devices that require 24bit DMA.
The recent work on x86 dma_alloc_coherent() breaks the ISA DMA buffer
allocation, which is represented by "dev = NULL" and requires 24bit
DMA implicitly.
Bisected-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Tested-by: Rene Herman <rene.herman@keyaccess.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: rdc: leds build/config fix
x86: sysfs cpu?/topology is empty in 2.6.25 (32-bit Intel system)
x86: revert commit 709f744 ("x86: bitops asm constraint fixes")
x86: restrict keyboard io ports reservation to make ipmi driver work
x86: fix fpu restore from sig return
x86: remove spew print out about bus to node mapping
x86: revert printk format warning change which is for linux-next
x86: cleanup PAT cpu validation
x86: geode: define geode_has_vsa2() even if CONFIG_MGEODE_LX is not set
x86: GEODE: cache results from geode_has_vsa2() and uninline
x86: revert geode config dependency
On some of our (single board computer) boards (x86) we are using an
IPMI controller that uses I/O ports 0x62 and 0x66 for a KCS (keyboard
controller style) IPMI system interface.
Trying to load the openipmi driver fails, because the ports
(0x62/0x66) are reserved for keyboard. keyboard reserves the full
range 0x60-0x6F while it doesn't need to.
Reserve only ports 0x60 and 0x64 for the legacy PS/2 i8042 keyboad
controller instead of 0x60-0x6F to allow the openipmi driver to work.
[ tglx: added 64bit fixup ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
If the task never used fpu, initialize the fpu before restoring the FP
state from the signal handler context. This will allocate the fpu
state, if the task never needed it before.
Reported-and-bisected-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Tested-by: Eric Sesterhenn <snakebyte@gmx.de>
Cc: Frederik Deweerdt <deweerdt@free.fr>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the scattered checks for PAT support to a single function. Its
moved to addon_cpuid_features.c as this file is shared between 32 and
64 bit.
Remove the manipulation of the PAT feature bit and just disable PAT in
the PAT layer, based on the PAT bit provided by the CPU and the
current CPU version/model white list.
Change the boot CPU check so it works on Voyager somewhere in the
future as well :) Also panic, when a secondary has PAT disabled but
the primary one has alrady switched to PAT. We have no way to undo
that.
The white list is kept for now to ensure that we can rely on known to
work CPU types and concentrate on the software induced problems
instead of fighthing CPU erratas and subtle wreckage caused by not yet
verified CPUs. Once the PAT code has stabilized enough, we can remove
the white list and open the can of worms.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This moves geode_has_vsa2 into a .c file, caches the result we get from
the VSA virtual registers, and causes the function to no longer be inline.
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Andres Salomon <dilinger@debian.org>
Cc: Jordan Crouse <jordan.crouse@amd.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
fix pcspkr dependancies: make the pcspkr platform
drivers to depend on a platform device, and
not the other way around.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
CC: Vojtech Pavlik <vojtech@suse.cz>
CC: Michael Opdenacker <michael-lists@free-electrons.com>
[fixed for 2.6.26-rc1 by tiwai]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix x86 setup printk format warming:
next-20080430/arch/x86/kernel/setup.c:172: warning: format '%lu' expects type 'long unsigned int', but argument 2 has type 'ssize_t'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Cc: mingo@elte.hu
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
http://bugzilla.kernel.org/show_bug.cgi?id=10547
Newer Dell OptiPlex 745s hang before rebooting after 'sudo reboot'.
A patch for some versions of the OptiPlex was proposed here --
http://lkml.org/lkml/2007/6/5/59 -- and is included in 2.6.23 and
later kernels, according to
http://lxr.linux.no/linux+v2.6.23/arch/i386/kernel/reboot.c . However,
the DMI_BOARD_NAME ("0WF810") is too restrictive. Newer OptiPlex
machines have a DMI_BOARD_NAME of "0RF703". I therefore suggest
adding another clause to reboot.c, similar to the one in the original
patch, but matching a DMI_BOARD_NAME of "0RF703".
On further inspection, it seems that there are other DMI_BOARD_NAMEs
for this same machine. They seem to change from time to time, which
means that the current code is fragile. Moreover, using bios reboot
should not break non-SFF OptiPlex 745s, and so a reasonable fix is to
simply drop the match on DMI_BOARD_NAME.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch makes the needlessly global additional_cpus static.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In kernel/acpi/realmode/Makefile use the 'always'
variable to say that wakeup.bin should always
be made.
In acpi/Makefile we then do not need to specify the
requested target and we avoid the message from make:
`arch/x86/kernel/acpi/realmode/wakeup.bin' is up to date.
Add wakeup.lds to list af targets to avoid rebuilding
wakeup.bin - from Roland McGrath.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@suse.cz>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the pv_apic_ops are only present if CONFIG_X86_LOCAL_APIC is compiled
in, kvmclock failed to build without this option. This patch fixes this.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This replaces the duplicated arch-specific versions of "sys_pipe()" with
one unified implementation. This removes almost 250 lines of duplicated
code.
It's marked __weak, so that *if* an architecture wants to override the
default implementation it can do so by simply having its own replacement
version, since many architectures use alternate calling conventions for
the 'pipe()' system call for legacy reasons (ie traditional UNIX
implementations often return the two file descriptors in registers)
I still haven't changed the cris version even though Linus says the BKL
isn't needed. The arch maintainer can easily do it if there are really
no obstacles.
Signed-off-by: Ulrich Drepper <drepper@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Don't warn in read_apic_id() when preemptible but only one CPU online.
Signed-off-by: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The .asciz directive takes any number of strings, but each one is zero-
terminated, and string pasting is not done as in C. That results in only the
first line being output.
Replace .asciz with multiple .ascii directives and terminate with .asciz.
Signed-off-by: Vegard Nossum <vegard.nossum@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The iommu_sac_force variable is needlessly defined global,
and this patch makes it static. Additionally, this variable
needs not be explicitly initialized.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch fixes one sparse warning by including the appropriate
header for the reboot_force symbol.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
the 'reboot_force' flag is a notion that non-PC subarchitectures do
not have.
also, unify the X86_BIOS_REBOOT option between 32-bit and 64-bit
and get rid of a few unnecessary Kconfig and Makefile complications
that way.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Al Viro pointed out that there's a missing readl() of timer->hpet_config,
found by Sparse.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (179 commits)
ACPI: Fix acpi_processor_idle and idle= boot parameters interaction
acpi: fix section mismatch warning in pnpacpi
intel_menlo: fix build warning
ACPI: Cleanup: Remove unneeded, multiple local dummy variables
ACPI: video - fix permissions on some proc entries
ACPI: video - properly handle errors when registering proc elements
ACPI: video - do not store invalid entries in attached_array list
ACPI: re-name acpi_pm_ops to acpi_suspend_ops
ACER_WMI/ASUS_LAPTOP: fix build bug
thinkpad_acpi: fix possible NULL pointer dereference if kstrdup failed
ACPI: check a return value correctly in acpi_power_get_context()
#if 0 acpi/bay.c:eject_removable_drive()
eeepc-laptop: add hwmon fan control
eeepc-laptop: add backlight
eeepc-laptop: add base driver
ACPI: thinkpad-acpi: bump up version to 0.20
ACPI: thinkpad-acpi: fix selects in Kconfig
ACPI: thinkpad-acpi: use a private workqueue
ACPI: thinkpad-acpi: fluff really minor fix
ACPI: thinkpad-acpi: use uppercase for "LED" on user documentation
...
Fixed conflicts in drivers/acpi/video.c and drivers/misc/intel_menlow.c
manually.
Replace TIF_RESTORE_SIGMASK with TS_RESTORE_SIGMASK and define our own
set_restore_sigmask() function. This saves the costly SMP-safe set_bit
operation, which we do not need for the sigmask flag since TIF_SIGPENDING
always has to be set too.
Signed-off-by: Roland McGrath <roland@redhat.com>
Cc: Oleg Nesterov <oleg@tv-sign.ru>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86-bigbox-pci:
x86: add pci=check_enable_amd_mmconf and dmi check
x86: work around io allocation overlap of HT links
acpi: get boot_cpu_id as early for k8_scan_nodes
x86_64: don't need set default res if only have one root bus
x86: double check the multi root bus with fam10h mmconf
x86: multi pci root bus with different io resource range, on 64-bit
x86: use bus conf in NB conf fun1 to get bus range on, on 64-bit
x86: get mp_bus_to_node early
x86 pci: remove checking type for mmconfig probe
x86: remove unneeded check in mmconf reject
driver core: try parent numa_node at first before using default
x86: seperate mmconf for fam10h out from setup_64.c
x86: if acpi=off, force setting the mmconf for fam10h
x86_64: check MSR to get MMCONFIG for AMD Family 10h
x86_64: check and enable MMCONFIG for AMD Family 10h
x86_64: set cfg_size for AMD Family 10h in case MMCONFIG
x86: mmconf enable mcfg early
x86: clear pci_mmcfg_virt when mmcfg get rejected
x86: validate against acpi motherboard resources
Fixed up fairly trivial conflicts in arch/x86/pci/{init.c,pci.h} due to
OLPC support manually.
