Pin configuration on pxa{25x,27x} has now separated from generic GPIO
into dedicated mfp-pxa2xx.c by this patch. The name "mfp" is borrowed
from pxa3xx and is used here to alert the difference between the two
concepts: pin configuration and generic GPIOs. A GPIO can be called
a "GPIO" _only_ when the corresponding pin is configured so.
A pin configuration on pxa{25x,27x} is composed of:
- alternate function selection (or pin mux as commonly called)
- low power state or sleep state
- wakeup enabling from low power mode
The following MFP_xxx bit definitions in mfp.h are re-used:
- MFP_PIN(x)
- MFP_AFx
- MFP_LPM_DRIVE_{LOW, HIGH}
- MFP_LPM_EDGE_*
Selecting alternate function on pxa{25x, 27x} involves configuration
of GPIO direction register GPDRx, so a new bit and MFP_DIR_{IN, OUT}
are introduced. And pin configurations are defined by the following
two macros:
- MFP_CFG_IN : for input alternate functions
- MFP_CFG_OUT : for output alternate functions
Every configuration should provide a low power state if it configured
as output using MFP_CFG_OUT(). As a general guideline, the low power
state should be decided to minimize the overall power dissipation. As
an example, it is better to drive the pin as high level in low power
mode if the GPIO is configured as an active low chip select.
Pins configured as GPIO are defined by MFP_CFG_IN(). This is to avoid
side effects when it is firstly configured as output. The actual
direction of the GPIO is configured by gpio_direction_{input, output}
Wakeup enabling on pxa{25x, 27x} is actually GPIO based wakeup, thus
the device based enable_irq_wake() mechanism is not applicable here.
E.g. invoking enable_irq_wake() with a GPIO IRQ as in the following
code to enable OTG wakeup is by no means portable and intuitive, and
it is valid _only_ when GPIO35 is configured as USB_P2_1:
enable_irq_wake( gpio_to_irq(35) );
To make things worse, not every GPIO is able to wakeup the system.
Only a small number of them can, on either rising or falling edge,
or when level is high (for keypad GPIOs).
Thus, another new bit is introduced to indicate that the GPIO will
wakeup the system:
- MFP_LPM_WAKEUP_ENABLE
The following macros can be used in platform code, and be OR'ed to
the GPIO configuration to enable its wakeup:
- WAKEUP_ON_EDGE_{RISE, FALL, BOTH}
- WAKEUP_ON_LEVEL_HIGH
The WAKEUP_ON_LEVEL_HIGH is used for keypad GPIOs _only_, there is
no edge settings for those GPIOs.
These WAKEUP_ON_* flags OR'ed on wrong GPIOs will be ignored in case
that platform code author is careless enough.
The tradeoff here is that the wakeup source is fully determined by
the platform configuration, instead of enable_irq_wake().
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
two reasons:
1. GPIO namings and their mode definitions are conceptually not part
of the PXA register definitions
2. this is actually a temporary move in the transition of PXA2xx to
use MFP-alike APIs (as what PXA3xx is now doing), so that legacy
code will still work and new code can be added in step by step
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
MFP configurations after resume should be done before the GPIO registers
are restored. Move the mfp sysdev registeration to the same place where
GPIO and IRQ sysdev(s) are registered to better control the order.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The main issue here is that pxa3xx does not have GAFRx registers,
access directly to these registers should be avoided for pxa3xx:
1. introduce __gpio_is_occupied() to indicate the GAFRx and GPDRx
registers are already configured on pxa{25x,27x} while returns
0 always on pxa3xx
2. pxa_gpio_mode(gpio | GPIO_IN) is replaced directly with assign-
ment of GPDRx, the side effect of this change is that the pin
_must_ be configured before use, pxa_gpio_irq_type() will not
change the pin to GPIO, as this restriction is sane, esp. with
the new MFP framework
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
To further clean up the GPIO and IRQ structure:
1. pxa_init_irq_gpio() and pxa_init_gpio() combines into a single
function pxa_init_gpio()
2. assignment of set_wake merged into pxa_init_{irq,gpio}() as
an argument
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the code better organized and simplified a bit. The change
will lose a bit of performance when performing IRQ ack/mask/unmask,but
that's not too much after checking the result binary.
This patch also removes the ugly #ifdef CONFIG_PXA27x .. #endif by
carefully not to access those pxa{27x,3xx} specific registers, this
is done by keeping an internal IRQ number variable. The pxa-regs.h
is also modified so registers for IRQ > PXA_IRQ(31) are made public
even if CONFIG_PXA{27x,3xx} isn't defined (for pxa25x's sake)
The incorrect assumption in the original code that internal irq starts
from 0 is also corrected by comparing with PXA_IRQ(0).
"struct sys_device" for the IRQ are reduced into one single device on
pxa{27x,3xx}.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
by
1. wrapping long lines and making comments tidy
2. using IRQ_TYPE_* instead of migration macros __IRQT_*
3. introduce a pr_debug() for the commented printk(KERN_DEBUG ...)
stuff
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
by:
1. introduce dedicated pxa_{mask,unmask}_low_gpio()
2. remove set_irq_chip(IRQ_GPIO_2_x, ...) which has already been
initialized in pxa_init_irq()
3. introduce dedicated pxa_init_gpio_set_wake()
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
1. As David Brownell suggests, using ffs() is going to make the loop
a bit faster (by avoiding unnecessary shift and iteration)
2. Russell suggested find_{first,next}_bit() being used with the
gedr[] array
Signed-off-by: eric miao <eric.miao@marvell.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The AC97 clock rate on PXA3xx is generated with a configurable divider
from sys_pll.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Expose control of the PXA3xx 13MHz CLK_POUT pin via the clock API
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Johannes Weiner <hannes@saeurebad.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
If we fail to boot due to an unsupported processor ID, print the
processor ID as part of the failure message.
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
U-Boot puts an image at the load address specified in the uImage
header before jumping to the entry point.
In the CONFIG_ZBOOT_ROM case ZBOOT_ROM_TEXT is the right load
address.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
None of these files use any of the functionality promised by
asm/semaphore.h. It's possible that they rely on it dragging in some
unrelated header file, but I can't build all these files, so we'll have
fix any build failures as they come up.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
By default, this option was selected by the platform Kconfig. This
patch adds "depends on" to L2X0 so that it can be enabled/disabled
manually.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch enables the building of Linux for the PB1176 platform.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the base files for the PB1176 platform support.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the resource and device definitions for the compact
flash.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the PB11MPCore support to the corresponding Kconfig
and Makefile to enable building.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds the base files for the PB11MPCore platform support.
Signed-off-by: Bahadir Balban <bahadir.balban@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
The upcoming PB11MPCore and PB1176 have different memory maps and some
of the definitions in platform.h are no longer common. This patch
moves them to the board-eb.h file and updates their usage in
realview_eb.c.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Since the PB1176 has different UART base addresses, this patch moves
the definitions form platorm.h to board-eb.h. It also modifies
uncompress.h to detect the platform type at run-time.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the timer definitions from platform.h into board-eb.h
as they are different on PB11MPCore and PB1176. It also adds
timerX_va_base variables in core.c which are set by the
realview_eb_timer_init function before invoking realview_timer_init.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the patch definitions into board-eb.h and
realview_eb.c (from core.c) as they are different on the PB11MPCore
and PB1176 platforms.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This is in preparation for the RealView PB11MPCore and PB1176 patches
which have different base addresses for the GIC.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
RealView/EB revD platform comes with the SMSC LAN9118 Ethernet
chip. This patch allows either the smc91x or the smc911x drivers to be
used with the RealView/EB platform.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch moves the SCU initialisation from __v6_setup to the
smp_prepare_cpus() function as it relies on platform-specific
settings. Changes to get_core_count() are mainly for allowing cleaner
code with the upcoming PB11MPCore patches.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch implements Thumb-2 application support in Linux. Original
implementation by Paul Brook with fixes for VFP and Neon by Catalin
Marinas.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch adds a prefetch abort handler similar to the data abort one
and renames the latter for consistency. Initial implementation by Paul
Brook with some renaming by Catalin Marinas.
Signed-off-by: Paul Brook <paul@codesourcery.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Add the TinCanTools Hammer board to list of supported machines in the
arch/arm/mach-s3c2410 directory, as well as a default config entry. the
mach-tct_hammer.c file initializes basic i/o, clocks, irqs, as well as
the mtd flash layout if enabled in the kernel configuration.
Signed-off-by: David Anders <danders@amltd.com>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
There seems to be some problem with at-least the S3C2440 and
bus traffic during an reset. It is unlikely, but still possible
that the system will hang in such a way that the watchdog cannot
get the system out of the state it is in.
Change to making the code that calls the watchdog reset run from
cached memory so that instruction fetches have quiesced before the
watchdog fires.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All current Simtec designs source the DCLK outputs from
the UPLL. This means the DCLK's parent must be set to UPLL
so that anything enabling and disabling an UPLL sourced
clock does not shutdown the DCLK due to missing open counts.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the name of the S3C2412_CLKDIVN_ARMDIVN define.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Change GPA21 to output over reset so that nRSTOUT is not
asserted whilst suspended.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
From: Juergen Beisert <j.beisert@pengutronix.de>
This patch separates the current code into i.MX2 and i.MX3 and modifies
the Kconfig files to reflect this separation in the menus.
Things happend since last review:
- make i.MX3 compile again
- fix some structure names to be conform with all the shared/common
sources from i.MX1/i.MX2
Previous changes:
- stay conform to other Kconfig files (note from Russell King)
Signed-off-by: Juergen Beisert <j.beisert@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Simple gpio-connected LED driver for KS8695 platforms.
(Based on old AT91 LED driver)
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update AT91SAM9/CAP9 PIT driver to use generic time and clockevent
infrastructure:
- Clocksource gives sub-microsecond timestamp precision, assuming
memory is clocked at over 16 MHz. It's less than a 32 bit counter,
unless it's is also generating IRQs.
- Clockevent device supports periodic mode only; no oneshot
support from this hardware. No IRQs generated unless it's the
active clocksource.
Later, another timer (probably from a TC module) can provide a oneshot
clockevent device to get NO_HZ and High-Res-Timer behavior.
This also updates the timekeeping to use the actual master clock rate
on the system, instead of compile-time <asm/arch/timex.h> constants
matching what Atmel's EK boards use. (Product boards may well differ!)
Plus cleanup: rename "*_timer*" symbols to "*_pit*" (there are other
timers, but only one PIT); shorter lines; remove needless CPP stuff;
make several symbols static; etc.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
All the SAM9 boards supported by mainline and the AT91 patches have
been converted to the new-style UART initialization. Therefore drop
support for the old at91_init_serial() interface for SAM9.
at91_uarts[] array can also be marked as __initdata.
The warning that no serial-console is defined moved from
at91_set_serial_console() to at91_add_device_serial() since the whole
point is the board-specific file is not calling
at91_set_serial_console().
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the emQbit ECB_AT91 board.
<http://wiki.emqbit.com/free-ecb-at91>
Original patch from Nelson Castillo.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Olimex SAM9-L9260 board.
<http://www.olimex.com/dev/sam9-L9260.html>
Original patch from Ivan Vasilev.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Support for the Kwikbyte KB9260 (CAM60) board.
<http://www.kwikbyte.com/KB9260.html>
Original patch from Kwikbyte.
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Semaphores are no longer performance-critical, so a generic C
implementation is better for maintainability, debuggability and
extensibility. Thanks to Peter Zijlstra for fixing the lockdep
warning. Thanks to Harvey Harrison for pointing out that the
unlikely() was unnecessary.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Acked-by: Ingo Molnar <mingo@elte.hu>
d142b6e77d added clock source support,
now it's time for the clock event support.
Tested-by: Thomas Kunze <thommycheck@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
These changes is the result of the discussion with Paul Walmsley.
His ideas are included into this patch.
Remove DPLL output divider handling from DPLLs and CLKOUTX2 clocks,
and place it into specific DPLL output divider clocks (e.g., dpll3_m2_clk).
omap2_get_dpll_rate() now returns the correct DPLL rate, as represented
by the DPLL's CLKOUT output. Also add MPU and IVA2 subsystem clocks, along
with high-frequency bypass support.
Add support for DPLLs function in locked and bypass clock modes.
Signed-off-by: Roman Tereshonkov <roman.tereshonkov@nokia.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove old PRCM register access code that is no longer needed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use shared clock code and new register
access.
Note that patch adds some temporary OLD_CK defines to keep patch
more readable. These temporary defines will be removed in the next
patch. Also not all clocks are changed in this patch to limit the
size.
Also, the patch fixes few incorrect clock defines in clock24xx.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a common clock framework for 24xx and 34xx.
Note that this patch does not add it to Makefile until in
next patch. Some functions are modified from earlier 24xx
clock framework code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves clock.h to clock24xx.c to make room for
adding common clock code for 24xx and 34xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch moves clock.h to clock24xx.h to make room for
adding common clock code for 24xx and 34xx.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes old 24xx PM code that does not really work for sleep
states, and uses old power management register access. Working PM code
will be added later.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes 24xx to use new register access, except for clock
framework. Clock framework register access will get updates in the
next patch.
Note that board-*.c files change GPMC (General Purpose Memory Controller)
access to use gpmc_cs_write_reg() instead of accessing the registers
directly. The code also uses gpmc_fck instead of it's parent clock
core_l3_ck for GPMC clock.
The H4 board file also adds h4_init_flash() function, which specify the
flash start and end addresses.
Also note that sleep.S removes some unused registers addresses.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds register access for 34xx power and clock management.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds common register access for 24xx and 34xx power
and clock management in order to share code between 24xx and 34xx.
Only change USB platform init code to use new register access, other
access will be changed in later patches.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Misc clean-up for the mux code and remove some unnecessary
ifdefs. Patch changes debug function so it can be used on
both 24xx and 34xx.
Changes are mostly for omap2, but patch also cleans up some
omap1 and common mux code.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove MPU-timer based sched_clock() in favor of the common one based
on 32k sync timer which works across all OMAP1/2/3 platforms.
Using 32k based one also gives a valid sched_clock() very early in the
boot process.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
These are no longer used and similar conversions are provided
by the clocksource/clockevent code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Move now OMAP1-specific timer32k code to mach-omap1 since OMAP2/3 32k
timers are done in gptimer code.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Since 32k timer code is moving to OMAP1 specific dir, move the
32k-based sched_clock() into common code where it is based on the 32k
sync counter and can be used even when using MPU timer.
While moving, change the ticks-to-nsecs conversion to use the helper
functions provided by clocksource.h.
Also removed the unused ticks_to_usec, leaving only ticks_to_nsec.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
On OMAP2/3, the gp-timer code can be used for a 32kHz timer simply by
setting the source to be the 32k clock instead of sys_clk.
This patch uses the mach-omap2/timer-gp.c code for 32kHz timer on
OMAP2, moving the logic into mach-omap2/timer-gp.c, and not using
plat-omap/timer32k.c which, for OMAP2, is redundant with the timer-gp
code.
Also, if CONFIG_OMAP_32K_TIMER is enabled, the gptimer-based
clocksource is not used. Instead the default 32k sync counter is used
as the clocksource (see the clocksource in plat-omap/common.c.) This
is important for sleep/suspend so there is a valid counter during
sleep. Note that the suspend/sleep code needs fixing to check for
overflows of this counter.
In addition, the OMAP2/3 details are removed from timer32k.c leaving
that with only OMAP1 specifics. A follow-up patch will move it from
plat-omap common code to mach-omap1.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Use omap processor specific function depending on system type.
Based on an earlier patch by Klaus Pedersen <klaus.k.pedersen@nokia.com>.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch changes pin multiplexing init to allow registering
custom function. The omap_cfg_reg() func will be split into
omap processor specific functions in later patch.
This is done to make adding omap3 pin multiplexing easier.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Currently, the GPIO interrupt handling is duplicating some of the work
done by the generic IRQ handlers (handle_edge_irq, handle_level_irq)
such as detecting nesting, handling re-triggers etc. Remove this
duplication and use generic hooks based on IRQ type.
Using generic IRQ handlers ensures correct behavior when using
threaded interrupts introduced by the -rt patch.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The clearing was moved to the unmask hook because it is known to run
after the interrupt handler has actually run. Before this patch, if
interrupts are threaded, the clearing/unmasking of level triggered
interrupts would be done before the threaded handler actually ran.
Signed-off-by: Kevin Hilman <khilman@mvista.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Convert OSK board to use new tps65010 gpiolib support. This
includes moving its LED support from leds-osk to gpio-leds,
giving more trigger options and a net platform code shrink.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Start cleaning up GPIO handling for OMAP5912 OSK board:
- Initialize GPIOs using the cross-platform calls, not the old
OMAP-private ones.
- Move touchscreen setup out of ads7846 code into board-specfic
setup code, where it belongs.
This doesn't depend on the patches to update OMAP to use the
gpiolib implementation framework.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update OMAP to use the new GPIO implementation framework. This is just a
quick'n'dirty update ... more code could now be removed, ideally as part
of cleaning up the entire OMAP GPIO infrastructure ...
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This deprecates old set/reset_scoop_gpio interfacein favour of
support for generic gpio interface.
It requires gpiolib, so it depends on the previous patch
(gpiolib for SA-1100).
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds gpiolib support for the SA-1100 arch:
- Move all GPIO API functions from generic.c into gpio.c
- Convert all gpio functions into gpiolib callbacks.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Make scoop driver use generic purpose io routines: ioread16
and iowrite16 instead of direct writing to memory.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cleanup most errors errors reported by sparse:
declare IO space as __iomem,
use %p for address printing
make functions static
Use __devinit instead of __init for scoop_init
Make scoop_remove __devexit and use __devexit_p for referencing it.
Signed-off-by: Dmitry Baryshkov <dbaryshkov@gmail.com>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Buffalo Linkstation Pro/Live is the same hardware as the
Kurobox Pro but without the NAND flash. This patch adds a
second MACHINE_START macro to the Kurobox setup file to minimise
code duplication.
Signed-off-by: Byron Bradley <byron.bbradley@gmail.com>
Acked-by: Nicolas Pitre <nico@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Updates the CSB637 platform's D1/PB2 LED to use gpio-led by default.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the D1/PB2 LED to use the gpio-leds API and heartbeat trigger.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the CSB637 to the new-style UART initialization API.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Converts the CSB337 target to the new UART initialization API.
Signed-off-by: Bill Gatliff <bgat@billgatliff.com>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the default configuration for the following AT91-based boards:
Embest ATEB9200
Cogent CSB337
Cogent CSB637
Sperry-Sun KAFA
Picotux200
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the default configuration for the following AT91-based boards:
Atmel AT91RM9200 DK
Atmel AT91RM9200 EK
Atmel AT91SAM9260 EK
Atmel AT91SAM9261 EK
Atmel AT91SAM9263 EK
Atmel AT91SAM9RL EK
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The bootloader on ts209 Orion boards doesn't configure the right
ethernet MAC address into the GigE unit on boot. The only way to
get the MAC address is by parsing it from the 'NAS Config' flash
partition, which is an ext2 partition that contains a file which
holds the MAC address in plain text (format "xx:xx:xx:xx:xx:xx\n")
-- this patch does that.
Tested-by: Martin Michlmayr <tbm@cyrius.com>
Cc: Byron Bradley <byron.bbradley@gmail.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the GPIO-driven LEDs (using NEW_LEDS) on the Atmel
SAM9260-EK and SAM9261-EK boards.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for AT73C213 audio DAC on the Atmel SAM9260-EK and
SAM9261-EK boards.
Signed-off-by: Sedji Gaouaou <sedji.gaouaou@atmel.com>
Signed-off-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
