Apparently, there is no sense in unmasking IRQ on the controller when you call
disable_irq_nosync() before doing this, set the nIEN bit afterwards, and then
unmask IRQ again after the command completion, hence 0 passed to SELECT_MASK()
before issuing the command in ide_config_drive_speed() is probably just a typo.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On user request (through sysfs), the IDLE IMMEDIATE command with UNLOAD
FEATURE as specified in ATA-7 is issued to the device and processing of
the request queue is stopped thereafter until the specified timeout
expires or user space asks to resume normal operation. This is supposed
to prevent the heads of a hard drive from accidentally crashing onto the
platter when a heavy shock is anticipated (like a falling laptop expected
to hit the floor). Port resets are deferred whenever a device on that
port is in the parked state.
v3:
Elias Oltmanns <eo@nebensachen.de> wrote:
[...]
> >> 1. Make sure that no negative value is being passed to
> >> jiffies_to_msecs() in ide_park_show().
> >> 2. Drop the superfluous variable hwif in ide_special_rq().
> >> 3. Skip initialisation of task and tf in ide_special_rq() if we are not
> >> handling a (un)park request.
> >
> > Well, #3 should have been done differently because we donn't want to
> > check for REQ_(UN)?PARK_HEADS more often than is necessary.
>
> While preparing the backport to 2.6.27, it has just occurred to me that
> we need to clear the IDE_DFLAG_PARKED flag in ide_disk_pre_reset()
> because this flag must not be set after *any* sort of access to the
> device.
v4:
Fix a memory leak due to a missing blk_put_request() in
issue_park_cmd(). Additionally, we should plug the queue when enqueueing
the unpark request because there is no guarantee that the park timeout
has not expired by then. Even though the chance for that to happen is
very slim, the request might end up hanging in the queue until the next
I/O operation is queued up. While at it, clean up the code a little:
- make issue_park_cmd() a function of type void since nobody cares for
the return value anyway;
- use blk_start_queueing() instead of __blk_run_queue() since we don't
have to worry about recursion;
- remove a superfluous pointer deference in task_no_data_intr().
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: Jeff Garzik <jeff@garzik.org>,
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Factor out reset error reporting from reset_pollfunc()
to ide_reset_report_error() helper.
While at it:
- fix KERN_* printk() levels
- remove 'switch ()'
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use 'drive->dn & 1' in ide_init_disk().
* remove [ata_]select_t.
While at it:
* Use ATA_DEVICE_OBS define in ide_port_init_devices_data().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add 'unsigned long dev_flags' to ide_drive_t and convert bitfields
to IDE_DFLAG_* flags.
While at it:
- IDE_DFLAG_ADDRESSING -> IDE_DFLAG_LBA48
- fixup some comments
- remove needless g->flags zeroing from ide*_probe()
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use optimized ATA version check from Sergei in ata_id_is_sata().
* ide_dev_is_sata() -> ata_id_is_sata()
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Include <linux/ata.h> directly in <linux/ide.h>
instead of through <linux/hdreg.h>.
* Include <linux/hdreg.h> only when needed.
Cc: Christoph Hellwig <hch@infradead.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Make ide_busy_sleep() take timeout value as a parameter
and also allow use of AltStatus Register if requested with
altstatus parameter. Update existing users accordingly.
* Convert ide_driveid_update() and actual_try_to_identify()
to use ide_busy_sleep().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
On Friday 25 July 2008, Linus Torvalds wrote:
>
> On Fri, 25 Jul 2008, Ben Dooks wrote:
> >
> > personally, i would much prefer to see the loop being less evil
> > like:
> >
> > for (p = s; p < end; p += 2)
> > be16_to_cpus((u16 *)p);
>
> Well, in this case, the code actually depends on 'p' being back at the
> start of the buffer by the end of it all, so it would need some more
> changes than that.
>
> But yes, I applied David's patch, but I _also_ suspect that we would be
> better off without code that does horrid things like casts and assignments
> inside the function arguments.
>
> So it would be nice to re-code that loop to be more readable. But due to
> the reliance of 'p' being 's' after the loop, the minimal patch would be
> something like the appended.
>
> Bartlomiej - take this or not, I'm not going to commit it - I haven't
> tested it, nor do I even have any machines that would trigger it. So this
> is more a "maybe something like this" than anything else.
From: Linus Torvalds <torvalds@linux-foundation.org>
CC: Ben Dooks <ben-linux@fluff.org>
Cc: David Miller <davem@davemloft.net>
Cc: harvey.harrison@gmail.com
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ATA_CMD_* defines instead of WIN_* ones.
While at it:
* EXABYTE_ENABLE_NEXT -> ATA_EXABYTE_ENABLE_NEST
* SETFEATURES_{EN,DIS}_WCACHE -> SETFEATURES_WC_{ON,OFF}
* SETFEATURES_{EN,DIS}_AAM -> SETFEATURES_AAM_{ON,OFF}
* SMART_* -> ATA_SMART_*
* Remove stale comment from ide-proc.c.
Partially based on earlier work by Chris Wedgwood.
Acked-by: Chris Wedgwood <cw@f00f.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Factor out HDIO_[OBSOLETE,GET]_IDENTITY ioctls handling
to ide_get_identity_ioctl().
* Use temporary buffer in ide_get_identity_ioctl() instead
of accessing drive->id directly.
* Add ide_id_to_hd_driveid() inline to convert raw id into
struct hd_driveid format (needed on big-endian).
* Use ide_id_to_hd_driveid() in ide_get_identity_ioctl(),
cleanup ide_fix_driveid() and switch ide to use use raw id.
* Remove no longer needed drive->driveid.
This leaves us with 3 users of struct hd_driveid in tree:
- arch/um/drivers/ubd_kern.c
- drivers/block/xsysace.c
- drivers/usb/storage/isd200.c
While at it:
* Use ata_id_u{32,64}() and ata_id_has_{dma,lba,iordy}() macros.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make drive->id an unnamed union so id can be accessed either by using
'u16 *id' or 'struct hd_driveid *driveid'. Then convert all existing
drive->id users accordingly (using 'u16 *id' when possible).
This is an intermediate step to make ide 'struct hd_driveid'-free.
While at it:
- Add missing KERN_CONTs in it821x.c.
- Use ATA_ID_WORDS and ATA_ID_*_LEN defines.
- Remove unnecessary checks for drive->id.
- s/drive_table/table/ in ide_in_drive_list().
- Cleanup ide_config_drive_speed() a bit.
- s/drive1/dev1/ & s/drive0/dev0/ in ide_undecoded_slave().
v2:
Fix typo in drivers/ide/ppc/pmac.c. (From Stephen Rothwell)
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Fix byte-swapping for id->words161_175[], id->words206_254[]
and id->words206_254[].
Luckily all words previously left in little-endian byte-order
are marked as reserved so this fix shouldn't affect user-space
applications.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add struct ide_tp_ops for transport methods.
* Add 'const struct ide_tp_ops *tp_ops' to struct ide_port_info
and ide_hwif_t.
* Set the default hwif->tp_ops in ide_init_port_data().
* Set host driver specific hwif->tp_ops in ide_init_port().
* Export ide_exec_command(), ide_read_status(), ide_read_altstatus(),
ide_read_sff_dma_status(), ide_set_irq(), ide_tf_{load,read}()
and ata_{in,out}put_data().
* Convert host drivers and core code to use struct ide_tp_ops.
* Remove no longer needed default_hwif_transport().
* Cleanup ide_hwif_t from methods that are now in struct ide_tp_ops.
While at it:
* Use struct ide_port_info in falconide.c and q40ide.c.
* Rename ata_{in,out}put_data() to ide_{in,out}put_data().
v2:
* Fix missing convertion in ns87415.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Lets remove dead Virtual DMA support for now so it doesn't clutter
core IDE code (it can be bring back when there is a need for it):
* Remove IDE_HFLAG_VDMA host flag.
* Remove ide_drive_t.vdma flag.
* cs5520.c: remove stale FIXMEs, cs5520_dma_host_set() and cs5520_dma_ops
(also there is no longer a need to set IDE_HFLAG_NO_ATAPI_DMA).
There should be no functional changes caused by this patch.
Cc: TAKADA Yoshihito <takada@mbf.nifty.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer needed ->INB, ->OUTB and ->OUTBSYNC methods.
Then:
* Remove no longer used default_hwif_[mm]iops() and ide_[mm_]outbsync().
* Cleanup SuperIO handling in ns87415.c.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_read_bcount_and_ireason() helper and use it instead of ->INB
in {cdrom_newpc,ide_pc}_intr().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add IDE_TFLAG_IN_FEATURE taskfile flag for reading Feature
register and handle it in ->tf_read.
* Convert ide_read_error() to use ->tf_read instead of ->INB,
then uninline and export it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert SELECT_DRIVE() to use ->tf_load instead of ->OUTB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Convert ide_config_drive_speed() to use ->tf_load instead of ->OUTB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Write ATA Feature register before ATA Sector Count register as
a preparation to use ->tf_load in ide_config_drive_speed().
This change shouldn't affect anything (just an usual paranoia).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->set_irq method for setting nIEN bit of ATA Device Control
register and use it instead of ide_set_irq().
While at it:
* Use ->set_irq in init_irq() and do_reset1().
* Don't use HWIF() macro in ide_check_pm_state().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_read_altstatus() inline helper.
* Add ->read_altstatus method for reading ATA Alternate Status
register and use it instead of ->INB.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove ide_read_status() inline helper.
* Add ->read_status method for reading ATA Status register
and use it instead of ->INB.
While at it:
* Don't use HWGROUP() macro.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->exec_command method for writing ATA Command register
and use it instead of ->OUTBSYNC.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ->dma_base + offset instead of ->dma_{status,command}
and remove no longer needed ->dma_{status,command}.
While at it:
* Use ATA_DMA_* defines.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ->read_sff_dma_status method for reading DMA Status register
and use it instead of ->INB.
While at it:
* Use inb() directly in ns87415.c::ns87415_dma_end().
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Make sure that each error condition during the execution of an
HDIO_DRIVE_RESET ioctl is actually reported to the calling process.
Also, unify the exit path of reset_pollfunc() when returning ide_stopped
since the need of ->port_ops->reset_poll() to be treated specially has
vanished (way back, it seems).
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Currently, the code path executing an HDIO_DRIVE_RESET ioctl is broken
in various ways. Most importantly, it is treated as an out of band
request in an illegal way which may very likely lead to system lock ups.
Use the drive's request queue to avoid this problem (and fix a locking
issue for free along the way).
Signed-off-by: Elias Oltmanns <eo@nebensachen.de>
Cc: "Alan Cox" <alan@lxorguk.ukuu.org.uk>
Cc: "Randy Dunlap" <randy.dunlap@oracle.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Remove drive->ctl (it is always equal to 0x08 after init time).
While at it:
* Use ATA_DEVCTL_OBS define.
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Move IRQ unmasking out from ->tf_load method to its users.
There should be no functional changes caused by this patch
(SELECT_MASK() is NOP except for hpt366, icside and sgiioc4).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always call SELECT_MASK(..., 0) in ide_tf_load() (needs to be done
to match ide_set_irq(..., 1)) and then remove IDE_TFLAG_NO_SELECT_MASK
taskfile flag.
This change should only affect hpt366 and icside host drivers since
->maskproc(..., 0) for sgiioc4 is equivalent to ide_set_irq(..., 1).
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Since ide_driveid_update() uses polling to execute the IDENTIFY DEVICE command
but clears nIEN bit in the control register and doesn't mask the IDE interrupt,
the latter does happen and lead to the corresponding message to appear:
ide0: unexpected interrupt, status=0x58, count=1
when e.g. running hdparm with option -X with a non-PCI IDE driver...
Signed-off-by: Mikhail Cherkashin <mcherkashin@ru.mvista.com>
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
SELECT_MASK() can now become static.
[bart: remove space between function name and open parenthesis]
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Skip "VLB sync" in ata_{in,out}put_data() if host uses MMIO.
* Use I/O ops directly in ata_vlb_sync() an drop no longer needed
'ide_drive_t *drive' argument.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Remove no longer used ->INW and ->OUTW methods.
While at it:
* scc_pata.c: scc_ide_{out,in}w() is called only in scc_tf_{load,read}()
so inline it there.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Add ->tf_load and ->tf_read methods to ide_hwif_t and set the default
methods in default_hwif_transport().
* Use ->tf_{load,read} instead o calling ide_tf_{load,read}() directly.
* Make ide_tf_{load,read}() static.
There should be no functional changes caused by this patch.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Add ide_execute_pkt_cmd() helper for executing PACKET command,
then convert ATAPI device drivers to use it.
As a nice side-effect this fixes ide-{floppy,tape,scsi} w.r.t.
ide_lock taking (ide-cd was OK).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Always use ->OUTBSYNC method for executing commands so the posting is done
if needed (this affects only pmac and scc_pata host drivers at the moment).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Use ins{w,l}()/outs{w,l}() and __ide_mm_ins{w,l}()/__ide_mm_outs{w,l}()
directly in ata_{in,out}put_data() (by using IDE_HFLAG_MMIO host flag to
decide which I/O ops are required).
* Remove no longer needed ->INS{W,L} and ->OUTS{W,L} methods (ide-h8300,
au1xxx-ide and scc_pata implement their own ->{in,out}put_data methods).
There should be no functional changes caused by this patch.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* Merge ->atapi_{in,out}put_bytes and ->ata_{in,out}put_data methods
into new ->{in,out}put_data methods which take number of bytes to
transfer as an argument and always do padding.
While at it:
* Use 'hwif' or 'drive->hwif' instead of 'HWIF(drive)'.
There should be no functional changes caused by this patch (all users
of ->ata_{in,out}put_data methods were using multiply-of-4 word counts).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
