This adds support for the Agere ET1011c PHY as found on the AMCC Taishan
board.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds BCM5248 and Marvell 88E1111 PHY support to NEW EMAC driver.
These PHY chips are used on PowerPC 440EPx boards.
The PHY code is based on the previous work by Stefan Roese <sr@denx.de>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
No need to convert to bytes and back - cleanup unneeded code.
Adapted from fix from 'Roel Kluin <12o3l@tiscali.nl>'
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The bnx2x module depends on the zlib_inflate functions. The
build will fail if ZLIB_INFLATE has not been selected manually
or by building another module that automatically selects it.
Modify BNX2X config option to 'select ZLIB_INFLATE' like BNX2
and others. This seems to fix it.
Signed-off-by: Lee Schermerhorn <lee.schermerhorn@hp.com>
Acked-by: Eliezer Tamir <eliezert@broadcom.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update GPIO mapping for T3C.
Update xgmac for T3C support.
Fix typo in mtu table.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fixes a race condition in module unload. Without this change,
workqueue events may fire while bonding data structures are partially
freed but before bond_close() is invoked by unregister_netdevice().
Update version to 3.2.3.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add new hash for balance-xor and 802.3ad modes. Originally
submitted by "Glenn Griffin" <ggriffin.kernel@gmail.com>; modified by
Jay Vosburgh to move setting of hash policy out of line, tweak the
documentation update and add version update to 3.2.2.
Glenn's original comment follows:
Included is a patch for a new xmit_hash_policy for the bonding driver
that selects slaves based on MAC and IP information. This is a middle
ground between what currently exists in the layer2 only policy and the
layer3+4 policy. This policy strives to be fully 802.3ad compliant by
transmitting every packet of any particular flow over the same link.
As documented the layer3+4 policy is not fully compliant for extreme
cases such as ip fragmentation, so this policy is a nice compromise
for environments that require full compliance but desire more than the
layer2 only policy.
Signed-off-by: "Glenn Griffin" <ggriffin.kernel@gmail.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: David Sterba <dsterba@suse.cz>
Use macros for comparing jiffies. Jiffies' wrap caused missed events and hangs.
Module reinsert was needed to make bonding work again.
Signed-off-by: David Sterba <dsterba@suse.cz>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
For consistency with the behaviour of the arp_ip_target option,
let /sys/class/net/bond0/bonding/xmit_hash_policy accept and report
current policy even if the bonding mode in effect does not use it.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
Adhere to coding style: break line after the if condition
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
Code for rendering multivalue sysfs files occurs three times
in this module. Rename 'buffer' to 'buf' in the first, for
the sake of consistency.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
The previous code returned '\n' (that is, a single empty line)
from most files, with one exception (xmit_hash_policy), where
it returned 'NA\n'. This patch consolidates each file to return
nothing at all if not applicable, not even a '\n'.
I find this behaviour more usual, more useful, more efficient
and shorter to code from both sides.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
From: Wagner Ferenc <wferi@niif.hu>
Also remove trailing spaces from multivalued files.
This fixes output like for example:
$ od -c /sys/class/net/bond0/bonding/slaves
0000000 e t h - l e f t e t h - r i g
0000020 h t \n \0
0000025
It mostly entails deleting '+1'-s after sprintf() calls: the return value
of sprintf is the number of characters printed, without the closing NUL,
ie. exactly what the sysfs interface requires. The three multivalue
cases are different, because they also have to swallow back a trailing
space.
Signed-off-by: Ferenc Wagner <wferi@niif.hu>
Acked-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The LED in the current driver will not be controlled correctly. During
a link change the carrier of the link is not available and the LED
will never turn on.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a field to the lro_mgr struct so that drivers can specify how much
padding is required to align layer 3 headers when a packet is copied
into a freshly allocated skb by inet_lro.c:lro_gen_skb(). Without
padding, skbs generated by LRO will cause alignment warnings on
architectures which require strict alignment (seen on sparc64).
Myri10GE is updated to use this field.
Signed-off-by: Andrew Gallatin <gallatin@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Lately I've got this nice badness on mdio bus removal:
Device 'e0103120:06' does not have a release() function, it is broken and must be fixed.
------------[ cut here ]------------
Badness at drivers/base/core.c:107
NIP: c015c1a8 LR: c015c1a8 CTR: c0157488
REGS: c34bdcf0 TRAP: 0700 Not tainted (2.6.23-rc5-g9ebadfbb-dirty)
MSR: 00029032 <EE,ME,IR,DR> CR: 24088422 XER: 00000000
...
[c34bdda0] [c015c1a8] device_release+0x78/0x80 (unreliable)
[c34bddb0] [c01354cc] kobject_cleanup+0x80/0xbc
[c34bddd0] [c01365f0] kref_put+0x54/0x6c
[c34bdde0] [c013543c] kobject_put+0x24/0x34
[c34bddf0] [c015c384] put_device+0x1c/0x2c
[c34bde00] [c0180e84] mdiobus_unregister+0x2c/0x58
...
Though actually there is nothing broken, it just device
subsystem core expects another "pattern" of resource managment.
This patch implement phy device's release function, thus
we're getting rid of this badness.
Also small hidden bug fixed, hope none other introduced. ;-)
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Eliminate an uninitialized variable warning. The code is correct, but
a pointer to the automatic variable 'addr' is passed to dma_alloc_coherent.
Since addr has never been initialized, and the compiler doesn't know
what dma_alloc_coherent will do with it, it complains.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turns out we're freeing the skb when we detect CRC error, but we're
not clearing out info->skb. We could either clear it and have the stack
reallocate it, or just leave it and the rx ring refill code will reuse
the one that was allocated.
Reusing a freed skb obviously caused some nasty crashes of various kind,
as reported by Brent Baude and David Woodhouse.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent deadlock in sky2 recovery logic. sky2_down calls napi_synchronize
which gets stuck if napi was already disabled.
Fix by rearranging slightly and not calling napi_disable until after
both ports are stopped. The napi_disable probably is being overly
paranoid, but it is safe now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The mpc5200 fec driver is corrupting memory. This patch fixes two bugs
where the wrong skb was being referenced.
Signed-off-by: Jon Smirl <jonsmirl@gmail.com>
Acked-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (27 commits)
[INET]: Fix inet_diag dead-lock regression
[NETNS]: Fix /proc/net breakage
[TEXTSEARCH]: Do not allow zero length patterns in the textsearch infrastructure
[NETFILTER]: fix forgotten module release in xt_CONNMARK and xt_CONNSECMARK
[NETFILTER]: xt_TCPMSS: remove network triggerable WARN_ON
[DECNET]: dn_nl_deladdr() almost always returns no error
[IPV6]: Restore IPv6 when MTU is big enough
[RXRPC]: Add missing select on CRYPTO
mac80211: rate limit wep decrypt failed messages
rfkill: fix double-mutex-locking
mac80211: drop unencrypted frames if encryption is expected
mac80211: Fix behavior of ieee80211_open and ieee80211_close
ieee80211: fix unaligned access in ieee80211_copy_snap
mac80211: free ifsta->extra_ie and clear IEEE80211_STA_PRIVACY_INVOKED
SCTP: Fix build issues with SCTP AUTH.
SCTP: Fix chunk acceptance when no authenticated chunks were listed.
SCTP: Fix the supported extensions paramter
SCTP: Fix SCTP-AUTH to correctly add HMACS paramter.
SCTP: Fix the number of HB transmissions.
[TCP] illinois: Incorrect beta usage
...
dma_addr_t is 64bit wide on some architectures (for example 64bit MIPS),
so it's not a good idea to use it for 32bit wide addresses in descriptors.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The VIA veloicty driver needs the following to allow changing MTU when down.
The buffer size needs to be computed when device is brought up, not when
device is initialized. This also fixes a bug where the buffer size was
computed differently on change_mtu versus initial setting.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This kind of sucks, and prevents the Fedora installer from using the
device for network installs...
[root@efika phy]# iwconfig eth0
Warning: Driver for device eth0 has been compiled with an ancient version
of Wireless Extension, while this program support version 11 and later.
Some things may be broken...
eth0 ESSID:off/any Nickname:""
NWID:0 Channel:0 Access Point: 00:00:BF:81:14:E0
Bit Rate:-1.08206e+06 kb/s Sensitivity=0/0
RTS thr:off Fragment thr:off
Encryption key:<too big>
Power Management:off
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This helps to allow the Fedora installer to use the built-in Ethernet on
the Efika for a network install.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x.h is a bit of a mess, not supporting any sort of generic
configuration. For the moment only ARCH_PXA and SH_MAGIC_PANEL_R2 have
suitable definitions, so we reflect this in the Kconfig also.
While there are other SH boards that will likely turn this on in the
2.6.25 time frame, it's not worth trying to stub around at the moment.
Fixes up the allmodconfig build, as noted by akpm.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't exit polling when we have not yet used our budget, this causes
the NAPI system to end up with a messed up poll list.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add workaround for issues FE+ (A0) transmit watermark.
This is copied verbatim from vendor driver sk98lin (10.22.4.3).
Don't have that chip version and no more information seems to be available.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using PCIE advanced error recovery stuff creates more user problems than it's worth.
The AER stuff depends on MMCONFIG and in many configurations it just doesn't work.
Plus it doesn't add any real functionality to the driver. The sky2
driver handles its own errors fine as is.
This reverts 555382cbfc
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using the hardware window into PCI config space is more reliable
and smaller/faster than using the pci_config routines. It avoids issues
with MMCONFIG etc.
Reverts: 167f53d05f
Please apply for 2.6.24
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
netif_rx_complete() should be called only
when work_done < budget.
Signed-off-by: Divy Le ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The patch ensures that a GSO skb has enough headroom
to push an encapsulating cpl_tx_pkt_lso header.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Extend the RGMII-Internal Delay specification case to include
TX-only and RX-only variants.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously, Internal Delay specification implied the delay be
applied to both TX and RX. This patch allows for separate TX/RX-only
internal delay specification.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Tested-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Acked-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The code to change MTU doesn't correctly handle all the chip variations
and requirements for restarting. On Genesis chips changing MTU would just
cause receiver to hang.
Use a simpler approach of just taking link down/up if needed.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
For compatiablity with sk98lin, make sure and set same values
in serial mode register.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Need to increase TX threshold when doing Jumbo frames on dual port board
to avoid underruns. (Code from sk98lin).
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver would not work over fibre if other end when down then
came back up (would require reloading driver). The correct way
to manage the link the same way for both TP and fibre.
Resloves problem described in: http://lkml.org/lkml/2007/11/6/395
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure and retry when shutting down the MAC. This code is copied
from sk98lin driver.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Receive FIFO overrun is not catastrophic condition, so don't flush when
it happens.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The calculation of usable FIFO RAM is wrong in the skge driver.
First, is doesn't take into account the reserved area on the original
SysKonnect Genesis boards. Second it has an off-by-one error because
hw->ports is either 1 or 2.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix the case when the card initialization fails on a mtu change and then
close is called (due to ifdown), which frees non existent rx buffers.
- Returning appropriate error codes in init_nic function.
- In s2io_close function s2io_card_down is called only when device is up.
- In s2io_change_mtu function return value of s2io_card_up function
is checked and returned if it failed.
Signed-off-by: Surjit Reang <surjit.reang@neterion.com>
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Ramkrishna Vepa <ram.vepa@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes iwl_mac_add_interface.
1. Currently only one interface is supported, instead of silently retuning
0 now it returns -EOPNOTSUPP (By Johannes Berg)
2. It enables changing mac address from user space (By Ian Schram)
Signed-off-by: Tomas Winkler <tomas@localhost.localdomain>
Cc: Zhu Yi <yi.zhu@intel.com>
Cc: Reinette Chatre <reinette.chatre@intel.com>
Cc: linux-wireless <linux-wireless@vger.kernel.org
Cc: Ian Schram <ischram@telenet.be>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
lbs_mac_event_disconnected() was called once and then never again
upon a hardware MAC event.
The reason was that the driver didn't clean the correct bit in the interrupt
cause register of the chip.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
I'm not sure why it was doing this, and I'm not sure I _want_ to know
why. But calling it NETIF_F_DYNALLOC doesn't change the fact that the
kernel believes it to be NETIF_F_IPV6_CSUM, and that IPv6 communication
is hence buggered.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix some left-over URLs and ifdefs in b43 and b43legacy drivers.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Saleem Abdulrasool <compnerd@compnerd.org>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
sungem's gem_reset_task() will unconditionally try to disable NAPI even
when it's called while the interface is not operating and hence the NAPI
struct isn't enabled. Make napi_disable() depend on gp->running.
Also removes a superfluous test of gp->running in the same function.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/iser: Add missing counter increment in iser_data_buf_aligned_len()
IB/ehca: Fix static rate regression
mlx4_core: Fix state check in mlx4_qp_modify()
IB/ipath: Normalize error return codes for posting work requests
IB/ipath: Fix offset returned to ibv_modify_srq()
IB/ipath: Fix error path in QP creation
IB/ipath: Fix offset returned to ibv_resize_cq()
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/net-2.6: (41 commits)
[XFRM]: Fix leak of expired xfrm_states
[ATM]: [he] initialize lock and tasklet earlier
[IPV4]: Remove bogus ifdef mess in arp_process
[SKBUFF]: Free old skb properly in skb_morph
[IPV4]: Fix memory leak in inet_hashtables.h when NUMA is on
[IPSEC]: Temporarily remove locks around copying of non-atomic fields
[TCP] MTUprobe: Cleanup send queue check (no need to loop)
[TCP]: MTUprobe: receiver window & data available checks fixed
[MAINTAINERS]: tlan list is subscribers-only
[SUNRPC]: Remove SPIN_LOCK_UNLOCKED
[SUNRPC]: Make xprtsock.c:xs_setup_{udp,tcp}() static
[PFKEY]: Sending an SADB_GET responds with an SADB_GET
[IRDA]: Compilation for CONFIG_INET=n case
[IPVS]: Fix compiler warning about unused register_ip_vs_protocol
[ARP]: Fix arp reply when sender ip 0
[IPV6] TCPMD5: Fix deleting key operation.
[IPV6] TCPMD5: Check return value of tcp_alloc_md5sig_pool().
[IPV4] TCPMD5: Use memmove() instead of memcpy() because we have overlaps.
[IPV4] TCPMD5: Omit redundant NULL check for kfree() argument.
ieee80211: Stop net_ratelimit/IEEE80211_DEBUG_DROP log pollution
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (56 commits)
Blackfin arch: fix bug when enable uart1 with uart0 disabled => no initial console
Blackfin arch: split apart dump_bfin_regs and merge/remove show_regs from process.c, which was largely duplicated
Blackfin arch: use common __INIT/__FINIT defines rather than setting the .section ourselves to .init.text
Blackfin arch: fix bug when sending signals with the wrong PC, cause gdb get confused
Blackfin arch: Ensure we printk out strings with the proper loglevel
Blackfin arch: Need to specify ax with the .init.text section,
Blackfin arch: Update Kconfig to latest Blackfin silicon datasheets
Blackfin arch: update defconfig files
Blackfin arch: Fix typo, and add ENDPROC - no functional changes
Blackfin arch: convert READY to DMA_READY as it causes build errors in common sound code otherwise
Blackfin arch: add defines for the on-chip L1 ROM of BF54x
Blackfin arch: cplb and map header file cleanup
Blackfin arch: cleanup the cplb declares
Blackfin arch: fix broken on BF52x, remove silly checks on processors for L1_SCRATCH defines
Blackfin arch: add support for working around anomaly 05000312
Blackfin arch: cleanup BF54x header file and add BF547 definition
Blackfin arch: fix building for BF542 processors which only have 1 TWI
Blackfin arch: rename _return_from_exception to _bfin_return_from_exception and export it
Blackfin arch: move EXPORT_SYMBOL() to C files where the symbol is actually defined
Blackfin arch: fix bug NOR Flash MTD mount fail
...
Plip passes a string "name" that is allocated on stack to
parport_register_device. parport_register_device holds the pointer to
"name" and when the registering function exits, it points nowhere.
On some machine, this bug causes bad names to appear in /proc, such as
/proc/sys/dev/parport/parport0/devices/T^/�X^/�, on others, the plip
proc node is completely missing.
The patch also fixes documentation to note this requirement.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
netif_rx is meant to be called from interrupts because it doesn't wake
up ksoftirqd. For calling from outside interrupts, netif_rx_ni exists.
This fixes plip to use netif_rx_ni. It fixes the infamous error "NOHZ:
local_softirq_panding 08" that happens on some machines with NOHZ and
plip --- it is caused by the fact that softirq is pending and ksoftirqd
is sleeping.
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Accidently I reversed the order of pci_save_state and
pci_set_power_state in .suspend()/.resume() callbacks
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
smc911x_set_multicast_list fails to fill out the multicast hash table
correctly; Bit 1 was used rather than bit 5 to decide if the lower or
upper register should be used.
The function is at the same time cleaned up by calling ether_crc rather
than using it's own bit reversal table.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Marvell Yukon XL chipset appears to have a hardware glitch
where it will repeat the checksum of the last packet. Of course, this is
timing sensitive and only happens sometimes...
More info: http://bugzilla.kernel.org/show_bug.cgi?id=9381
As a workaround just disable hardware checksumming by default on
this chip version. The earlier workaround for PCIX, dual port
was also on Yukon XL so don't need to disable checksumming there.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Prevent driver from brawly logging packet checksum errors.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Using own tx_packets counter instead of firmware counters.
Signed-off-by: Thomas Klein <tklein@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The smc911x_local pointer in smc911x_rcv is only used in the SMC_USE_DMA
case. Move it under the #ifdef so GCC doesn't generate a warning in the
non-DMA case.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
elif defined(CONFIG_*) should be used instead of elif CONFIG_*
so GCC doesn't give warnings about undefined symbols when the config
option is disabled.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The amd8111e network driver was broken by
bea3348eef, which makes the driver
call napi_enable() and napi_disable() even if the driver had been
configured without CONFIG_AMD8111E_NAPI, and thus
netif_napi_add() had not been called on initialization.
This triggers a BUG in napi_enable().
This patch fixes the problem. Please apply.
Signed-off-by: Jiri Bohac <jbohac@suse.cz>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A printk in the error handling code of dm9601.c was missing a newline.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a long boot delay in the forcedeth driver. During initialization, the
timeout for the handshake between mgmt unit and driver can be very long.
The patch reduces the timeout by eliminating a extra loop around the
timeout logic.
Addresses http://bugzilla.kernel.org/show_bug.cgi?id=9308
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Cc: Alex Howells <astinus@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch adds new device ids and features for mcp79 devices into the
forcedeth driver.
Signed-off-by: Ayaz Abdulla <aabdulla@nvidia.com>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
It's a bad idea to call flush_scheduled_work from within a
netdev->stop because the linkwatch will occasionally take the
rtnl lock from a workqueue context, and thus that can deadlock.
This reworks things a bit in that area to avoid the problem.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When checking the states passed in, mlx4_qp_modify() accidentally checks
cur_state twice rather than checking cur_state and new_state. Fix this
to make sure that both values are in-bounds.
Since these values may be passed in from userspace, this bug results in
userspace being able to trigger an oops.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Cc: stable <stable@kernel.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
The usb max packet size won't change during the
device's presence. We should store it in a
variable inside rt2x00dev and use that.
This should also fix a division error when the
device is being hot-unplugged while a frame is
being send out.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The virtio code never hooked through the ->remove callback. Although
noone supports device removal at the moment, this code is already
needed for module unloading.
This of course also revealed bugs in virtio_blk, virtio_net and lguest
unloading paths.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NETFILTER]: Fix NULL pointer dereference in nf_nat_move_storage()
[SUNHME]: VLAN support for sunhme
[CHELSIO]: Fix skb->dev setting.
[NETFILTER]: fix compat_nf_sockopt typo
[INET]: Fix potential kfree on vmalloc-ed area of request_sock_queue
[VIA_VELOCITY]: Don't oops on MTU change.
iwl4965: fix not correctly dealing with hotunplug
rt2x00: Fix chipset revision validation
iwl3945: place CCK rates in front of OFDM for supported rates
mac80211: Fix queuing of scan containing a SSID
This patch enables VLAN support on sunhme by increasing BMAC_TXMAX/BMAC_RXMAX
and allocating extra space via skb_put for the VLAN header.
Signed-off-by: Chris Poon <dev-null@telus.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
eth_type_trans() now sets skb->dev. Access skb->def after it gets
set.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 7fb7ac2411.
Heikki Orsila reports that it causes a regression:
"Doing
nc host port < /dev/zero
on a sending machine (not skge) to an skge machine that is receiving:
nc -l -p port >/dev/null
with ~60 MiB/s speed, causes the interface go malfunct. A slow
transfer doesn't cause a problem."
See
http://bugzilla.kernel.org/show_bug.cgi?id=9321
for some more information.
There is a workaround (also reported by Heikki):
"After some fiddling, I noticed that not changing the register write
order on patch:
+ skge_write32(hw, RB_ADDR(q, RB_END), end);
skge_write32(hw, RB_ADDR(q, RB_WP), start);
skge_write32(hw, RB_ADDR(q, RB_RP), start);
- skge_write32(hw, RB_ADDR(q, RB_END), end);
fixes the visible effect.. Possibly not the root cause of the
problem, but changing the order back fixes networking here."
but that has yet to be ack'ed or tested more widely, so the whole
problem-causing commit gets reverted until this is resolved properly.
Bisected-and-requested-by: Heikki Orsila <shdl@zakalwe.fi>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple mtu change when device is down.
Fix http://bugzilla.kernel.org/show_bug.cgi?id=9382.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
mlx4_core: Fix thinko in QP destroy (incorrect bitmap_free)
RDMA/cxgb3: Set the max_qp_init_rd_atom attribute in query_device
IB/ehca: Fix static rate calculation
IB/ehca: Return physical link information in query_port()
IB/ipath: Fix race with ACK retry timeout list management
IB/ipath: Fix memory leak in ipath_resize_cq() if copy_to_user() fails
mlx4_core: Fix possible bad free in mlx4_buf_free()
* 'master' of master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6:
[NET]: rt_check_expire() can take a long time, add a cond_resched()
[ISDN] sc: Really, really fix warning
[ISDN] sc: Fix sndpkt to have the correct number of arguments
[TCP] FRTO: Clear frto_highmark only after process_frto that uses it
[NET]: Remove notifier block from chain when register_netdevice_notifier fails
[FS_ENET]: Fix module build.
[TCP]: Make sure write_queue_from does not begin with NULL ptr
[TCP]: Fix size calculation in sk_stream_alloc_pskb
[S2IO]: Fixed memory leak when MSI-X vector allocation fails
[BONDING]: Fix resource use after free
[SYSCTL]: Fix warning for token-ring from sysctl checker
[NET] random : secure_tcp_sequence_number should not assume CONFIG_KTIME_SCALAR
[IWLWIFI]: Not correctly dealing with hotunplug.
[TCP] FRTO: Plug potential LOST-bit leak
[TCP] FRTO: Limit snd_cwnd if TCP was application limited
[E1000]: Fix schedule while atomic when called from mii-tool.
[NETX]: Fix build failure added by 2.6.24 statistics cleanup.
[EP93xx_ETH]: Build fix after 2.6.24 NAPI changes.
[PKT_SCHED]: Check subqueue status before calling hard_start_xmit
Declare mac using DECLARE_MAC_BUF for use when calling print_mac().
This fixes compile error where mac was undeclared.
Also, remove unused variable i.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
New (updated) version of ethernet driver for cris v10.
- First steps to simplify and make the MII code more similar
between the etrax100 and etraxfs ports.
- Start the transmit queue before enabling tx interrupts
to avoid race with the first frame.
- Flip the comparition statement to stick to physical addresses
to avoid phys_to_virt mapping a potential null pointer.
This was not an error but the change simplifies debugging
of address-space mappings.
- Made myPrevRxDesc local to e100_rx since it was only used there.
Fixed out of memory handling in e100_rx. If dev_alloc_skb() fails
persistently the system is hosed anyway but at least it won't
loop in an interrupt handler.
- Correct some code formatting issues.
- Add defines SET_ETH_ENABLE_LEDS, SET_ETH_DISABLE_LEDS
and SET_ETH_AUTONEG used in new cris v10 ethernet driver.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Acked-by: Mikael Starvik <starvik@axis.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The interrupt handler returns IRQ_NONE if it detects that the device
is gone. That's incorrect because the device may have raised the interrupt.
Not acknowledging it may trigger the spurious interrupt detection and kill
drivers sharing the interrupt line.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The validation of the chipset revision was broken
since for rt2500usb and rt73usb different registers
should be read. When rt2500usb was loaded for a rt73
device it would false think the chipset was correct
because the wrong register was read and validated.
This has been fixed by expanding the check to also
see if the first 4 bits of the revision is not-0
(When reading the wrong register offset the returned
value is usually 0 which can be interpreted as invalid)
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch fixes association failure (reason = 18) bug by arranging CCK
rates before OFDM rates. This patch will register with mac80211 the
modified rate arrangement with CCK rate first. Change rate scale algorithm
also to deal with rate change. Fix Txpower and rate Table commands to be
constructed correctly after rearrangement.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If fs_enet is build as module, on PPC_CPM_NEW_BINDING platforms
mii-fec/mii-bitbang should be build as module, as well. On other
platforms, mii-fec/mii-bitbang must be included into the main module.
Otherwise some symbols remain undefined. Additionally, fs_enet uses
libphy, so add a select PHYLIB.
Building modules, stage 2.
MODPOST 5 modules
ERROR: "fs_scc_ops" [drivers/net/fs_enet/fs_enet.ko] undefined!
make[1]: *** [__modpost] Error 1
make: *** [modules] Error 2
Signed-off-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix thinko in commit eaf559bf ("mlx4_core: Don't free special QPs in
QP number bitmap"). The old commit had the logic exactly backwards
and ended up freeing *only* special QPs, which not only left the
original bug in place but also introduced the problem that the QP
number bitmap would get full after a while.
Found by Dotan Barak of Mellanox.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
- Fixed memory leak by freeing MSI-X local entry memories when vector allocation
fails in s2io_add_isr.
- Added two utility functions remove_msix_isr and remove_inta_isr to eliminate
code duplication.
- Incorporated following review comments from Jeff
- Removed redundant stats->mem_freed and synchronize_irq call
- do_rem_msix_isr is renamed as remove_msix_isr
- do_rem_inta_isr is renamed as remove_inta_isr
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix bond_destroy and bond_free_all to not reference the struct
net_device after calling unregister_netdevice.
Bug and offending change reported by Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes no sense to enable interrupts if a device has been unplugged.
In addition if in doubt IRQ_HANDLED should be returned.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mii-tool can cause the driver to call msleep during nway reset,
bugzilla.kernel.org bug 8430. Fix by simply calling reinit_locked
outside of the spinlock, which is safe from ethtool, so it should be
safe from here.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by rmk from kautobuild output:
drivers/net/netx-eth.c: In function 'netx_eth_hard_start_xmit':
drivers/net/netx-eth.c:131: error: 'dev' undeclared (first use in this function)
drivers/net/netx-eth.c:131: error: (Each undeclared identifier is reported only once
drivers/net/netx-eth.c:131: error: for each function it appears in.)
drivers/net/netx-eth.c: In function 'netx_eth_receive':
drivers/net/netx-eth.c:158: error: 'dev' undeclared (first use in this function)
Signed-off-by: David S. Miller <davem@davemloft.net>
Reported by rmk from kautobuild output:
drivers/net/arm/ep93xx_eth.c:420: error: implicit declaration of function '__netif_rx_schedule_prep'
Signed-off-by: David S. Miller <davem@davemloft.net>
When mlx4_buf_free() is called from the error path of
mlx4_buf_alloc(), it may be passed a buffer structure that does not
have all pages filled in. Add a check for NULL to mlx4_buf_free() so
we avoid passing NULL to dma_free_coherent() (which will crash).
Signed-off-by: Ali Ayoub <ali@mellanox.co.il>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch reverts Eric's commit 2b008b0a8e
It diets .text & .data section of the kernel if CONFIG_NET_NS is not set.
This is safe after list operations cleanup.
Signed-of-by: Denis V. Lunev <den@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect length for strncat by replacing it with strlcat
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
With '<=' tick can be incremented up to 26, The last loop is redundant
since even when 'softstate' becomes 'STATE_READY', 'if (tick > 25)'
will still cause the function to return -1,
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch updates the version number to 3.86
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the PHY type reported through ethtool for copper
devices from MII to TP. The latter is more accurate.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the A1 revision of 5784, 5764, and 5761, and applies all
previous bugfixes. In places where the list of devices gets too long,
the patch uses a new TG3_FLG3_5761_5784_AX_FIXES flag instead.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previous devices hardcoded the PCI Maximum Read Request Size to 4K. To
better comply with the PCI spec, the hardware now defaults the MRRS to
512 bytes. This will yield poor driver performance if left untouched.
This patch increases the MRRS to 4K on driver initialization.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Internal hardware timers become inaccurate after link events. Clock
frequency switches performed by the CPMU fail to adjust timer
prescalers. The fix is to detect core clock frequency changes during
link events and adjust the timer prescalers accordingly.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most 5784 / 5764 LED modes do not work as expected because of a hardware
bug. This patch forces the LED mode to be in MAC LED mode.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
New CPMU devices contend with the GPHY for power management. The GPHY
autopowerdown feature is enabled by default in the PHY and thus needs to
be disabled after every PHY reset.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the LINK_SPEED mode to the list of CPMU modes that can
cause the loopback tests to fail. These bugs are planned to be fixed in
future revisions of the chip, so the patch qualifies the fixes as such.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Newer devices contain bootcode in the chip's private ROM area. This
bootcode is called selfboot. Selfboot can be patched in the device's
NVRAM and the patches can have several formats. In one particular
format, the checksum calculation needs to be slightly modified. This
patch adjusts the NVRAM test code for that case, and add support for the
missing formats.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5784 and 5764 devices lock up when the link speed is 10Mbps, the CPMU
link speed mode is enabled, and the MAC clock is running at 1.5Mhz. The
fix is to run the MAC clock at faster speeds.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch corrects a bug where the ENABLE_APE flag was tested against
the wrong flag variable.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
5784 and 5764 devices fail to link / pass traffic after one load /
unload cycle. This happens because of a hardware bug in the new CPMU.
During normal operation, the MAC depends on the PHY clock being
available. When the PHY is powered down, the clock the MAC depends on
is disabled. The fix is to switch the MAC clock to an alternate source
before powering down the PHY, and to restore the MAC clock to the PHY
source upon device resume.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When 5761 devices boot the machine using PXEboot, PXE leaves the device
active when it terminates. The tg3 driver has code to detect this
condition and resets the device during initialization. On 5761 devices,
device resets involve sending a driver state update message to the APE
on the 5761. However, during this initialization stage, communications
to the APE registers have not yet been set up. The driver then
dereferences a NULL pointer and crashes the machine. The fix is to move
the APE register access setup earlier in the initialization code to
cover this condition.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When I removed net-modules.txt because it only contained ancient
information I missed that many Kconfig entries pointed to this ancient
information.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit bea3348e (the NAPI changes) made sungem unconditionally enable
NAPI when resuming and unconditionally disable when suspending, this,
however, makes napi_disable() hang when suspending when the interface
was taken down before suspend because taking the interface down also
disables NAPI. This patch makes touching the napi struct in
suspend/resume code paths depend on having the interface up, thereby
fixing the hang on suspend.
The patch also moves the napi_disable() in gem_close() under the lock so
that the NAPI state is always modified atomically together with the
"opened" variable.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
fix sparse warnings "Using plain integer as NULL pointer"
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-virtio:
virtio: Force use of power-of-two for descriptor ring sizes
lguest: Fix lguest virtio-blk backend size computation
virtio: Fix used_idx wrap-around
virtio: more fallout from scatterlist changes.
virtio: fix vring_init for 64 bits
Prior to this patch, iwlwifi would always use the first
registered rate control algorithm which, depending on system
setup, could be anything. After the mac80211 patch to make
the simple algorithm built-in, it would always be simple.
This has always been a bug in iwlwifi.
This fixes it by requesting that mac80211 selects the right
rate control algorithm.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Oops.
The current code does not like being given an u16 with the highest
bit set as an argument to mdio_write. Let's enforce a correct range of
values for both the register address and value (resp. 5 and 16 bits).
The callers are currently left as-is.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
RTL_GIGA_MAC_VER_17 breaks as well.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Found a couple of more chips in the latest version of the vendor driver.
They are minor variations on existing chips.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ax88796: add superh to kconfig dependencies
This patch adds sh architecture support to the ax88796 kconfig.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Luckily, this wasn't reported or reproduced. The logical operation for
setting duplex had wrong grouping.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The link state machine requires access to some resources that
are shared with the iSCSI function on the chip. (See iSCSI
driver at drivers/scsi/qla4xxx) If the interface is being
up/downed at a rapid pace this driver may need to sleep
waiting to get access to the common resources. For this we
are moving the state machine to run as a work thread.
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure we don't feed packets with bad CRC up the network stack,
and discount the packet length as reported from the MAC for the CRC
field.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't use the "replace source address with local MAC address" bits, since
it causes problems on some variations of the hardware due to an erratum.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The standard validate_addr handler refuses to accept the all zeroes address
as valid. However, it's common historical practice for the bonding
master to be configured up prior to having any slaves, at which time the
master will have a MAC address of all zeroes.
Resolved by setting the dev->validate_addr to NULL. The master still can't
end up with an invalid address, as the set_mac_address function tests
for validity.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Looks like I incorrectly merged one of the rtnl lock changes,
so that one function, bonding_show_active_slave, held rtnl but didn't
release it, and another, bonding_store_active_slave, never held rtnl but
did release it.
Fixed so the first function doesn't mess with rtnl, and the
second correctly acquires and releases rtnl.
Bug reported by Moni Shoua <monis@voltaire.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Netpoll will only work on port 0 because of the restrictive
relationship between NAPI and netpoll.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PCMCIA needs an additional step to request the IRQ.
No need to add code to release the IRQ here, as that's done
automatically in pcmcia_disable_device().
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43legacy. If we call
b43legacy_wireless_core_stop(), it will set the status of the device to
INITIALIZED and the IRQ handler won't care any longer about IRQs, thus the
kernel will disable the IRQ if it's shared (unless we boot it with the
'irqpoll' option). So we must disable IRQs before changing the device
status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix an IRQ race condition in b43. If we call b43_stop_wireless_core(), it
will set the status of the device to INITIALIZED and the IRQ handler won't
care any longer about IRQs, thus the kernel will disable the IRQ if it's
shared (unless we boot it with the 'irqpoll' option). So we must disable
IRQs before changing the device status.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix possible buffer overrun.
The patch to b43 by Michael Buesch <mb@bu3sch.de> has been ported to
b43legacy.
Signed-off-by: Stefano Brivio <stefano.brivio@polimi.it>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The rfkill subsystem doesn't like code like that
rfkill_allocate();
rfkill_register();
rfkill_unregister();
rfkill_register(); /* <- This will crash */
This sequence happens with
modprobe b43
ifconfig wlanX up
ifconfig wlanX down
ifconfig wlanX up
Fix this by always re-allocating the rfkill stuff before register.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
wl->mutex might already be locked on initialization.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If i reaches zero, the loop ends, but the postfix decrement subtracts it to -1.
Testing for 'i == 0', later in the function, will not fulfill its purpose.
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fix section mismatch warning:
WARNING: vmlinux.o(.data+0x36fcc): Section mismatch: reference to .init.data:prism2_pci_id_table (between 'prism2_pci_drv_id' and 'prism2_pci_funcs')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rt2x00 is broken when it comes down to adhoc and master mode.
The main problem is the beaconing, which is completely failing.
Untill a solution has been found, both beacon requiring modes
must be disabled to prevent numerous bug reports.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Properly account for queue commands, this fixes a problem reported
by Holger Schurig when using the debugfs interface.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Incoming packets have to be aligned or the IP stack becomes upset.
Make sure to shift them two bytes to achieve this.
Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes for slow hardware.
Signed-off-by: Vitaly V. Bursov <vitalyvb@ukr.net>
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The Intel device supported by the hermes driver core is the IPW2011. The
"Intel PRO/Wireless" wording suggests the later Centrino devices and may
be confusing to some users.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Various symptoms depending on the .config options:
- the card stops working after some (short) time
- the card does not work at all
- the card disappears (nothing in lspci/dmesg)
A real power-off is needed to recover the card.
Signed-off-by: Mark Lord <mlord@pobox.com>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
The 8168c and the 8100e choke on it. I have not seen an indication
nor received a report that the TBI is being actively used on the
remaining 8168b and 8110. Let's disable it for now until someone
complains.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Matthias Winkler <m.winkler@unicon-ka.de>
Cc: Maarten Vanraes <maarten.vanraes@gmail.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This patch adds LAN91C111 ethernet interface support for zylonite
(a.k.a Marvell's PXA3xx Development Platform) with smc91x driver.
It would be better if a patch would support zylonite along with all
other PXA boards with a single binary of smc91x driver, but it looks
quite difficult for the moment, so ugly #ifdef is still used here.
Signed-off-by: Aleksey Makarov <amakarov@ru.mvista.com>
Acked-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCI AER support may not work for a couple of reasons.
It may not be configured into the kernel or there may be a BIOS
bug that prevents MMCONFIG from working. If MMCONFIG doesn't work
then the PCI registers that control AER will not be accessible via
pci_read_config functions; luckly there is another window to access
PCI space in the device, so use that.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IRQ's is already masked on shutdown, and on startup avoid
touching PHY until after phy_init().
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Don't need to change LED's after auto negotiation, the chip
sets them correctly.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Increse phy delay and handle I/O errors.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The D-Link PCI-X board (and maybe others) can lie about status
ring entries. It seems it will update the register for last status
index before completing the DMA for the ring entry. To avoid reading
stale data, zap the old entry and check.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some boards, PCI configuration space access is turned off by default.
The 2.6.24 driver doesn't turn it on, and should have.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We conciously make a change here - we permit mode and speed setting to
be done in things like SLIP mode. There isn't actually a technical
reason to disallow this. It's usually a silly thing to do but we can
do it and soemone might wish to do so.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All this USB_USBNET_MII trickery is simply not worth it considering how
few code it saves.
As a side effect, this also fixes the following compile error reported
by Toralf Frster:
<-- snip -->
...
LD .tmp_vmlinux1
drivers/built-in.o: In function `usbnet_set_settings':
(.text+0xf1876): undefined reference to `mii_ethtool_sset'
drivers/built-in.o: In function `usbnet_get_settings':
(.text+0xf1836): undefined reference to `mii_ethtool_gset'
drivers/built-in.o: In function `usbnet_get_link':
(.text+0xf18d6): undefined reference to `mii_link_ok'
drivers/built-in.o: In function `usbnet_nway_reset':
(.text+0xf18f6): undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It'd also be nice to mention "containers" somewhere in the help text
(I'm assuming that's what it's for?).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changes made on 18-sep to fix skb handling in the pppol2tp driver
broke the transmit and receive paths. Users are only running into this
now because distros are now using 2.6.23 and I must have messed up
when I tested the change.
For receive, we now do our own calculation of how much to pull from
the skb (variable length L2TP header) rather than using
skb_transport_offset(). Also, if the skb isn't a data packet, it must
be passed back to UDP with skb->data pointing to the UDP header.
For transmit, make sure skb->sk is set up because ip_queue_xmit()
needs it.
Signed-off-by: James Chapman <jchapman@katalix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It gets quite verbose to see every single PHY driver being registered
by default.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add PHY IDs for Marvell 88E1240. It seems to have close enough programming
models to 1111/1112 for basic support at least.
Also clean up whitespace in the ID list a bit.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
During booting of last vanilla kernel I got:
Trying to free nonexistent resource...
This because of if "ENABLE_APRICOT" is on we do:
request_region(ioaddr,...)
if (checksum test failed)
goto out1;
dev->base_addr = ioaddr;//<-here mistake
out1:
release_region(dev->base_addr,...)
This change fixes this bug for me.
Signed-off-by: Evgeniy Dushistov <dushistov@mail.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
A reasonably common problem with some devices is that they will
disable MSI generation when the INTX_DISABLE bit is set in the
PCI_COMMAND register.
Quirk this explicitly, guarding the pci_intx() calls in msi.c with
this quirk indication.
The first entries for this quirk are for 5714 and 5780 Tigon3 chips,
and thus we can remove the workaround code from the tg3.c driver.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Michael Chan <mchan@broadcom.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
* 'sg' of git://git.kernel.dk/linux-2.6-block:
[SG] Get rid of __sg_mark_end()
cleanup asm/scatterlist.h includes
SG: Make sg_init_one() use general table init functions
Not architecture specific code should not #include <asm/scatterlist.h>.
This patch therefore either replaces them with
#include <linux/scatterlist.h> or simply removes them if they were
unused.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
When testing the myri10ge driver with 2.6.24-rc1, I found
that the machine crashed under heavy load:
Unable to handle kernel paging request at 0000000000100108 RIP:
[<ffffffff803cc8dd>] net_rx_action+0x11b/0x184
The address corresponds to the list_move_tail() in
netif_rx_complete():
if (unlikely(work == weight))
list_move_tail(&n->poll_list, list);
Eventually, I traced the crashes to calling netif_rx_complete() with
work_done == budget. From looking at other drivers, it appears that
one should only call netif_rx_complete() when work_done < budget.
To fix it, I changed the test in myri10ge_poll() so that it refers
to to work_done rather than looking at the rx ring status. If
work_done is < budget, then that implies we have no more packets to
process. Any races will be resolved by the NIC when the write to
irq_claim is made.
In myri10ge_clean_rx_done(), if we ever exceeded our budget, it would
report a work_done one larger than was acutally done. This is because
the increment was done in the conditional, so work_done would be
incremented regardless of whether or not the test passed or failed.
This would lead to the WARN_ON_ONCE(work > weight); warning in
net_rx_action triggering. I've moved the increment of work_done
inside the loop. Note that this would only be a problem when we had
exceeded our budget.
Signed off by: Andrew Gallatin <gallatin@myri.com>
Andrew Gallatin Myricom Inc
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Driver shouldn't complain if the register range is larger than what
it expects. This works around failures with some device trees.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When not building an arch/powerpc kernel, the mpc5200 FEC driver depends
on some symbols which are not defined (BESTCOMM & BESTCOMM_FEC).
This patch flips around the dependancy logic so that it cannot be
selected unless BESTCOMM_FEC is selected first. Kconfig stops
complaining this way.
Also, the driver only works for arch/powerpc (not arch/ppc) anyway so
it should depend on PPC_MERGE also.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Finally, the zero_it argument can be completely removed from
the callers and from the function prototype.
Besides, fix the checkpatch.pl warnings about using the
assignments inside if-s.
This patch is rather big, and it is a part of the previous one.
I splitted it wishing to make the patches more readable. Hope
this particular split helped.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix links to files in Documentation/* in various Kconfig files
Signed-off-by: Dirk Hohndel <hohndel@linux.intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/netdev-2.6:
ixgb: fix TX hangs under heavy load
e1000e: Fix typo ! &
ixgbe: minor sparse fixes
e1000: sparse warnings fixes
ixgb: fix sparse warnings
e1000e: fix sparse warnings
mv643xx_eth: Fix MV643XX_ETH offsets used by Pegasos 2
Blackfin EMAC driver: Fix Ethernet communication bug (dupliated and lost packets)
DM9601: Support for ADMtek ADM8515 NIC
A merge error occurred where we merged the wrong block here
in version 1.0.120. The right condition for frags is slightly
different then for the skb, so account for the difference properly
and trim the TSO based size right.
Originally part of a fix reported by IBM to fix TSO hangs on
pSeries hardware.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make strings const if possible, and fix includes so forward definitions
are seen.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix sparse warnings and problems from e1000 driver.
Added a sparse fix for the module param array index
-- Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix sparse warnings in ixgb driver for net-2.6.24.
Added a sparse fix for invalid declaration using non-constant value
in ixgb_set_multi. Added a fix for the module param array index
and allows int params in the array. --Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix sparse warnings from e1000e driver in net-2.6.24.
Added a sparse fix for module param arrays which can have int values
but only the array index needs to be unsigned. --Auke
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix Ethernet communication bug(dupliated and lost packets)
in RMII PHY mode- dont call mac_disable and mac_enable during
10/100 REFCLK changes - mac_enable screws up the DMA descriptor chain
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add device ID for the ADMtek ADM8515 USB NIC to the DM9601 driver.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
(akpm: it's doing copy_to_user() inside spin_lock_irqsave(): this driver
appears to be beyond help).
Signed-off-by: Roel Kluin <12o3l@tiscali.nl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver for ethernet on mpc5200/mpc5200b SoCs (FEC).
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Acked-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
eHEA resources that are allocated via H_CALLs have a unique identifier each.
These identifiers are necessary to free the resources. A reboot notifier
is used to free all eHEA resources before the indentifiers get lost, i.e
before kexec starts a new kernel.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The legacy jumbo frame receive code is no longer needed since all
hardware can do packet split and we're no longer offering a bypass
kernel config option to disable packet split. Remove the unused code.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This workaround code performed software stripping instead of the
hardware which can do it much faster. None of the e1000e target
hardware has issues with this feature and should work fine. This
gives us some performance back on receive, and removes some
kludging stripping the 4 bytes.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Upon inspection the rx FIFO size calculation code was found to have
2 significant flaws: A superfluous minus sign resulting in the
wrong size to be used for jumbo frames on 82573 and ich9, as well
as that this code rewrote the read-only adapter->pba variable
resulting in different values at each run.
Without this patch jumbo's will work but performance will be
awkward since the TX size is not adequate for two whole frames.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix allocation and freeing of jumbo frames where several bugs
were recently introduced by cleanups after we forked this code
from e1000. This moves ps_pages to buffer_info where it really
belongs and makes it a dynamically allocated array. The penalty
is not that high since it's allocated outside of the buffer_info
struct anyway.
Without this patch all jumbo frames are completely broken and the
driver panics.
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
interrupt handlers return a return value these days.
Also, kill always-true test and unneeded void* cast.
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Fix for the error below while linking vmlinux:
[...]
drivers/built-in.o: In function `ipg_ioctl':
drivers/net/ipg.c:2148: undefined reference to `generic_mii_ioctl'
drivers/built-in.o: In function `ipg_get_settings':
drivers/net/ipg.c:2181: undefined reference to `mii_ethtool_gset'
drivers/built-in.o: In function `ipg_set_settings':
drivers/net/ipg.c:2193: undefined reference to `mii_ethtool_sset'
drivers/built-in.o: In function `ipg_nway_reset':
drivers/net/ipg.c:2205: undefined reference to `mii_nway_restart'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Avuton Olrich <avuton@gmail.com>
Cc: Jesse Huang <jesse@icplus.com.tw>
Cc: Sorbica Shieh <sorbica@icplus.com.tw>
Disabling napi polling early is well enough.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
Don't call napi_disable if not configured and make sure that any
misuse of napi_xxx in future fails with a compile error.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Cc: Edward Hsu <edward_hsu@realtek.com.tw>
This patch fixes the errors made in the users of the crypto layer during
the sg_init_table conversion. It also adds a few conversions that were
missing altogether.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is not safe to to place struct pernet_operations in a special section.
We need struct pernet_operations to last until we call unregister_pernet_subsys.
Which doesn't happen until module unload.
So marking struct pernet_operations is a disaster for modules in two ways.
- We discard it before we call the exit method it points to.
- Because I keep struct pernet_operations on a linked list discarding
it for compiled in code removes elements in the middle of a linked
list and does horrible things for linked insert.
So this looks safe assuming __exit_refok is not discarded
for modules.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fix the follwing for 3945:
1. Fix direct scan by make sure we set one_direct_scan only when the
mac80211 ask for direct scan.
2. Fix mac_stop and mac_remove_interface calles, we make sure we cancel any
scan and disassoc on these call
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following for 3945:
1. Make sure we cancel scan if RXON command is called.
2. Call scan abort on scan watchdog.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the following problems for 4965:
1. Fix direct scan by make sure we set one_direct_scan only when the
mac80211 ask for direct scan.
2. Fix mac_stop and mac_remove_interface calles, we make sure we cancel any
scan and disassoc on these call.
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fix the following:
1. make sure we are not scanning before we call REPLY_RXON
2. set RXON_FILTER_ASSOC_MSK only after we receive association response
3. call scan abort on scan watchdog instead of restart
Signed-off-by: Mohamed Abbas <mabbas@linux.intel.com>
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removeis TSF flag from probe request. TSF should be added only to
probe response.
Signed-off-by: Helmut Schaa <hschaa@suse.de>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch allows rtl8187 to receive multicast frames if requested.
Signed-off-by: Michael Wu <flamingice@sourmilk.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When rounding a relative timeout we need to use round_jiffies_relative().
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
[IPV4]: Explicitly call fib_get_table() in fib_frontend.c
[NET]: Use BUILD_BUG_ON in net/core/flowi.c
[NET]: Remove in-code externs for some functions from net/core/dev.c
[NET]: Don't declare extern variables in net/core/sysctl_net_core.c
[TCP]: Remove unneeded implicit type cast when calling tcp_minshall_update()
[NET]: Treat the sign of the result of skb_headroom() consistently
[9P]: Fix missing unlock before return in p9_mux_poll_start
[PKT_SCHED]: Fix sch_prio.c build with CONFIG_NETDEVICES_MULTIQUEUE
[IPV4] ip_gre: sendto/recvfrom NBMA address
[SCTP]: Consolidate sctp_ulpq_renege_xxx functions
[NETLINK]: Fix ACK processing after netlink_dump_start
[VLAN]: MAINTAINERS update
[DCCP]: Implement SIOCINQ/FIONREAD
[NET]: Validate device addr prior to interface-up
* 'sg' of git://git.kernel.dk/linux-2.6-block:
fix sg_phys to use dma_addr_t
ub: add sg_init_table for sense and read capacity commands
x86: pci-gart fix
blackfin: fix sg fallout
xtensa: dma-mapping.h is using linux/scatterlist.h functions, so include it
SG: audit of drivers that use blk_rq_map_sg()
arch/um/drivers/ubd_kern.c: fix a building error
SG: Change sg_set_page() to take length and offset argument
AVR32: Fix sg_page breakage
mmc: sg fallout
m68k: sg fallout
More SG build fixes
sg: add missing sg_init_table calls to zfcp
SG build fix
This patch makes the host RNDIS driver talk to RNDIS devices with an MTU
less than 1.5k, instead of refusing to talk to such a device.
Signed-Off-by: Thomas Sailer <t.sailer@alumni.ethz.ch>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
--
Hi Jeff,
are you the right person to send this to?
Nobody else seems to be wanting to forward this to Linus...
Thanks,
Tom
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use fixed_mdio_get_phydev for obtaining fixed phy instances and adopt to
changed fixed phy device naming.
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert cpmac to new napi_struct API introduced by
bea3348eef [NET]: Make NAPI polling independent
of struct net_device objects.
Only disable rx interrupts if napi actually has been scheduled.
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Switch to using DECLARE_MAC_BUF/print_mac() added by commit
0795af5729 [NET]: Introduce and use print_mac()
and DECLARE_MAC_BUF().
Signed-off-by: Eugene Konev <ejka@imfi.kspu.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Andrew Nelless <andrew@nelless.net> wrote:
> Hi,
>
> I booted up 2.6.24-rc1 this morning [Real early over a brew ;-)] and
> was having a problems with multiple ~5 second hangs on SATA/drive init
> (Something to do with "EH" something-or-other and resets but I'll
> email in separately about it later unless its fixed by the time I get
> the chance).
>
> Anyway, I went to fire up netconsole to get a decent log dump and hit
> across the following nasty. Netconsole works fine in 2.6.23.1 with a
> similar config and the same kernel parameters.
>
> A shot of the screen is the only method I could come up with to
> capture the log, I hope that is OK, it is pretty readable.
>
>
> The nasty:
> http://andotnet.nfshost.com/linux/2.6.24-rc1-netconsole-nullderef.jpg
the NULL dereference is here:
(gdb) list *0xffffffff804a9504
0xffffffff804a9504 is in natsemi_poll (drivers/net/natsemi.c:717).
712 return count;
713 }
714
715 static inline void __iomem *ns_ioaddr(struct net_device *dev)
716 {
717 return (void __iomem *) dev->base_addr;
718 }
719
which is this code from natsemi.c:
2227 struct net_device *dev = np->dev;
2228 void __iomem * ioaddr = ns_ioaddr(dev);
2229 int work_done = 0;
seems like the NAPI changes in -rc1 added an np->dev field but forgot to
initialize it ...
does the patch below fix the oops for you?
Ingo
-------------------->
Subject: natsemi: fix oops, link back netdevice from private-struct
From: Ingo Molnar <mingo@elte.hu>
this commit:
commit bea3348eef
Author: Stephen Hemminger <shemminger@linux-foundation.org>
Date: Wed Oct 3 16:41:36 2007 -0700
[NET]: Make NAPI polling independent of struct net_device objects.
added np->dev to drivers/net/natsemi.c's struct netdev_private, but
forgot to initialize that new field upon driver init. The result was
a predictable NULL dereference oops the first time the hardware
generated an interrupt.
Reported-by: Andrew Nelless <andrew@nelless.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
napi_disable / napi_enable must be applied on all ehea queues.
Signed-off-by: Jan-Bernd Themann <themann@de.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch contains the following cleanups:
- make ipg_nic_get_stats() static
- move DefaultPhyParam[] from ipg.h to ipg.c and make it static
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Most drivers need to set length and offset as well, so may as well fold
those three lines into one.
Add sg_assign_page() for those two locations that only needed to set
the page, where the offset/length is set outside of the function context.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Some are already declared in include/linux/netdevice.h, while
some others (xfrm ones) need to be declared.
The driver/net/rrunner.c just uses same extern as well, so
cleanup it also.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'irq-upstream' of master.kernel.org:/pub/scm/linux/kernel/git/jgarzik/misc-2.6:
[SPARC, XEN, NET/CXGB3] use irq_handler_t where appropriate
drivers/char/riscom8: clean up irq handling
isdn/sc: irq handler clean
isdn/act2000: fix major bug. clean irq handler.
char/pcmcia/synclink_cs: trim trailing whitespace
drivers/char/ip2: separate polling and irq-driven work entry points
drivers/char/ip2: split out irq core logic into separate function
[NETDRVR] lib82596, netxen: delete pointless tests from irq handler
Eliminate pointless casts from void* in a few driver irq handlers.
[PARPORT] Remove unused 'irq' argument from parport irq functions
[PARPORT] Kill useful 'irq' arg from parport_{generic_irq,ieee1284_interrupt}
[PARPORT] Consolidate code copies into a single generic irq handler
Update ALB mode monitor to hold correct locks (RTNL and nothing
else) when calling dev_set_promiscuity.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert more lock acquisitions to _bh flavor to avoid deadlock
with workqueue activity and add acquisition of RTNL in appropriate places.
Affects ALB mode, as well as core bonding functions and sysfs.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert locking-related activity to new & improved system.
Convert some lock acquisitions to _bh and rework parts of ALB mode, both
to avoid deadlocks with workqueue activity.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert mii (link state) monitor to acquire correct locks for
failover events. In particular, failovers generally require RTNL at a low
level (when manipulating device MAC addresses, for example) and no other
locks. The high level monitor is responsible for acquiring a known set
of locks, RTNL, the bond->lock for read and the slave_lock for write, and
the low level failover processing can then release appropriate locks as
needed. This patch provides the high level portion.
As it is undesirable to acquire RTNL for every monitor pass (which
may occur as often as every 10 ms), the miimon has been converted to
do conditional locking. A first pass inspects all slaves to determine
if any action is required, and if so, a second pass (after acquring RTNL)
is done to perform any actions (doing a complete rescan, as the situation
may have changed when all locks were released).
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change locking in balance-rr transmit processing to use a free
running counter to determine which slave to transmit on. Instead, a
free-running counter is maintained, and modulo arithmetic used to select
a slave for transmit.
This removes lock operations from the TX path, and eliminates
a deadlock introduced by the conversion to work queues.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert bonding timers to workqueues. This converts the various
monitor functions to run in periodic work queues instead of timers. This
patch introduces the framework and convers the calls, but does not resolve
various locking issues, and does not stand alone.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add missing &:
drivers/net/pasemi_mac.c: In function 'pasemi_mac_clean_rx':
drivers/net/pasemi_mac.c:553: warning: passing argument 1 of 'prefetch'
makes pointer from integer without a cast
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The dfx_bus_uninit() call is called from dfx_unregister() which is
__devexit and which is ultimately the ->remove call for the device.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
