Address the issue of EDAC/BIOS coexistence for the e752x chip-sets.
We have found a problem where the BIOS will start the system with the error
registers (dev0:fun1) hidden and assuming it has exclusive access to them.
The edac driver violates this assumption.
The workaround this patch offers is to honor the hidden-ness as an
indication that it is not safe to use those registers.
Signed-off-by: Mark Gross <mark.gross@intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC_752X uses pci_scan_single_device(), which is only available if
CONFIG_HOTPLUG is enabled, so limit this driver with HOTPLUG.
Signed-off-by: Randy Dunlap <rdunlap@xenotime.net>
Cc: Dave Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix a lot of typos. Eyeballed by jmc@ in OpenBSD.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Change all instances of EXPORT_SYMBOL() in the core EDAC module to
EXPORT_SYMBOL_GPL().
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Dave Jiang <djiang@mvista.com>: Fix EDAC e752x driver so it
outputs sysbus-specific error message when sysbus error detected.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Cosmetic indentation/formatting cleanup for EDAC code. Make sure we
are using tabs rather than spaces to indent, etc.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix EDAC code so EXPORT_SYMBOL comes after the function that is being
exported. This is to maintain consistency with the rest of the kernel.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add x86 dependency in drivers/edac/Kconfig for all current
platform-specific modules.
- Add PCI dependency to Radisys 82600 driver
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix code so we always hold mem_ctls_mutex while we are stepping
through the list of mem_ctl_info structures. Otherwise bad things
may happen if one task is stepping through the list while another
task is modifying it. We may eventually want to use reference
counting to manage the mem_ctl_info structures. In the meantime we
may as well fix this bug.
- Don't disable interrupts while we are walking the list of
mem_ctl_info structures in check_mc_devices(). This is unnecessary.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- After we unregister a kobject, wait for our kobject release method
to call complete(). This causes us to wait until the kobject
reference count reaches 0. Otherwise, a task accessing the EDAC
sysfs interface can hold the reference count above 0 until after the
EDAC module has been unloaded. When the reference count finally
drops to 0, this will result in an attempt to call our release
method inside the EDAC module after the module has already been
unloaded.
This isn't the best fix, since a process can get stuck sleeping forever
uninterruptibly if the user does the following:
rmmod my_module < /sys/my_sysfs/file
I'll go back and implement a better fix later. However this should
be ok for now.
- Call edac_remove_sysfs_mci_device() from edac_mc_del_mc() rather
than from edac_mc_free(). Since edac_mc_add_mc() calls
edac_create_sysfs_mci_device(), edac_mc_del_mc() should call
edac_remove_sysfs_mci_device().
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Remove calls to kobject_init(). These are unnecessary because
kobject_register() calls kobject_init().
- Remove extra calls to kobject_put(). When we call
kobject_unregister(), this releases our reference to the kobject.
The extra calls to kobject_put() may cause the reference count to
drop to 0 while a kobject is still in use.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is part 2 of a 2-part patch set.
Fix edac_mc_add_mc() so it cleans up properly if call to
edac_create_sysfs_mci_device() fails.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is part 1 of a 2-part patch set. The code changes are split into
two parts to make the patches more readable.
Move complete_mc_list_del() and del_mc_from_global_list() so we can
call del_mc_from_global_list() from edac_mc_add_mc() without forward
declarations. Perhaps using forward declarations would be better?
I'm doing things this way because the rest of the code is missing
them.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix xxx_probe1() functions so they call xxx_get_error_info() functions
to clear initial errors. This is simpler and cleaner than duplicating
the low-level code for accessing PCI config space.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Fix minor logic bug in e7xxx_remove_one().
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix i82875p_probe1() so it calls pci_get_device() instead of
pci_find_device().
- Fix i82875p_probe1() so it cleans up properly on failure.
- Fix i82875p_init() so it cleans up properly on failure.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Fix i82860_init() so it cleans up properly on failure.
- Fix i82860_exit() so it cleans up properly.
- Fix typo in comment (i.e. www.redhat.com.com).
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Add ctl_dev field to "struct e752x_dev_info". Then we can eliminate
ugly switch statement from e752x_probe1().
- Remove code from e752x_probe1() that clears initial PCI bus parity
errors. The core EDAC module already does this.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Eliminate unnecessary calls to pci_dev_get() and pci_dev_put() from
amd76x driver.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Perform the following name substitutions on all source files:
sed 's/BS_MOD_STR/EDAC_MOD_STR/g'
sed 's/bs_thread_info/edac_thread_info/g'
sed 's/bs_thread/edac_thread/g'
sed 's/bs_xstr/edac_xstr/g'
sed 's/bs_str/edac_str/g'
The names that start with BS_ or bs_ are artifacts of when the code
was called "bluesmoke".
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This implements the following idea:
On Monday 30 January 2006 19:22, Eric W. Biederman wrote:
> One piece missing from this conversation is the issue that we need errors
> in a uniform format. That is why edac_mc has helper functions.
>
> However there will always be errors that don't fit any particular model.
> Could we add a edac_printk(dev, ); That is similar to dev_printk but
> prints out an EDAC header and the device on which the error was found?
> Letting the rest of the string be user specified.
>
> For actual control that interface may be to blunt, but at least for people
> looking in the logs it allows all of the errors to be detected and
> harvested.
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch was originally posted by Christoph Hellwig (see
http://lkml.org/lkml/2006/2/14/331):
"Christoph Hellwig" <hch@lst.de> wrote:
> Use the kthread_ API instead of opencoding lots of hairy code for kernel
> thread creation and teardown, including tasklist_lock abuse.
>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: <dave_peterson@pobox.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- Disable the EDAC sysfs code. The sysfs interface that EDAC presents to
user space needs more thought, and is likely to change substantially.
Therefore disable it for now so users don't start depending on it in its
current form.
- Disable the default behavior of calling panic() when an uncorrectible
error is detected (since for now, there is no sysfs interface that allows
the user to configure this behavior).
Signed-off-by: David S. Peterson <dsp@llnl.gov>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Disable (via ugly #if 0's) the 3 sysfs files that I think by now we all
agree are very much wrong. These files shouldn't become part of the ABI by
the 2.6.16 release, so I rather have this minimal patch merged to disable
them for now, the real fix can then come during the 2.6.17 devel window.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
EDAC is still causing a few problems and the code is relatively green. Mark
it as experimental until thing settle down.
Also, provide some documentation pointers in Kconfig help.
Signed-off-by: Tim Small <tim@buttersideup.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
By including version.h edac_mc was rebuilding on every incremental build.
Which defeats the point of incremental builds.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The AMD76x chipsets aren't used in 64-bit, so don't offer the driver to the
user.
Signed-off-by: Dave Jones <davej@redhat.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is a subset of the bluesmoke project core code, stripped of the NMI work
which isn't ready to merge and some of the "interesting" proc functionality
that needs reworking or just has no place in kernel. It requires no core
kernel changes except the added scrub functions already posted.
The goal is to merge further functionality only after the core code is
accepted and proven in the base kernel, and only at the point the upstream
extras are really ready to merge.
From: doug thompson <norsk5@xmission.com>
This converts EDAC to sysfs and is the final chunk neccessary before EDAC
has a stable user space API and can be considered for submission into the
base kernel.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: doug thompson <norsk5@xmission.com>
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
