pci_enable_msi failure is a normal event so we should not print any error.
Going over the code I spotted a missing pci_disable_msi() leak when irq
allocation fails. The whole code also needed a cleanup, so I combined the
two different calls to pci_request_irq into a single call making this
look a lot better. All #ifdef CONFIG_PCI_MSI's have been removed.
Compile tested with both CONFIG_PCI_MSI enabled and disabled.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pci_enable_msi calls can fail for normal operational reasons. Driver
should not print an error message in that case. Fix a leak that leaves
msi enabled if pci_request_irq fails. We can remove CONFIG_PCI_MSI
ifdefs alltogether
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Fix for driver on System-p
This patch will fix a ping issue on system-p
Signed-off by: Milan Bag <mbag@netxen.com>
Signed-off by: Adhiraj Joshi <adhiraj@netxen.com>
Signed-by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Spidernet was the driver I original did all the node-aware netdevice
allocation for, but after a year it still hasn't hit mainline.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Linas Vepstas <linas@austin.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The hardware must not see that is given ownership of a buffer until it is
completely written, and when the driver receives ownership of a buffer,
it must ensure that any other reads to the buffer reflect its final
state. Thus, I/O barriers are added where required.
Without this patch, I have observed GCC reordering the setting of
bdp->length and bdp->status in gfar_new_skb. Hardware reordering
was also theoretically possible.
Signed-off-by: Scott Wood <scottwood@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix link speed detection change.
Thanks to Stefan Roese <sr@denx.de> for finding this bug.
CC: Stefan Roese <sr@denx.de>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Original patch is from Jeff Haran <jharan@brocade.com> with my minor style
fixes. His comments follow:
The first problem was in the function that configures the PHY for
autonegotiation, genmii_setup_aneg(). The original code does a
read/modify/write of the autonegotiation advertizement register (reg 4),
followed by a read/modify/write of the control register (reg 0). While
the original code follows the proper procedure as per reading the IEEE
specs, what I found is that on at least one PHY model (National DP83843)
the read of the control register comes back with the soft reset bit set
(bit 15). Because of the read/modify/write operation, this causes the
write to write a 1 back to the reset bit, which initiates a software
reset of the PHY. This software reset causes the PHY to return to its
power up state which advertizes all modes of operation, thus negating
the write to the autoneg advertizement register. The modification is to
spin reading the control register until the soft reset bit is clear
before doing the modify/write.
The second problem was in the function that configures the PHY for
forced operation, genmii_setup_forced(). The original code initiates a
software reset operation via a write of a 1 to bit 15 of the control
register (reg 0), but then proceeds to do a second write to that same
register without waiting until that reset bit is cleared by the PHY
itself (which according to the IEEE specs indicates that the PHY reset
is complete). This is a violation of how one is supposed to use this
software reset feature of these PHYs and I believe was the cause of
mysterious, difficult to reproduce link failures that we've observed on
some of our systems that use this driver. The fix is to modify the
function so that it spins waiting for the reset bit to clear after doing
the soft reset and before doing the subsequent write.
Signed-off-by: Jeff Haran <jharan@brocade.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Eugene Surovegin <ebs@ebshome.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do some memory barrier changes for safety/perfomance:
Don't need read after update to index, mmiowb() followed by read at end
of irq is sufficient.
Signed-off-by: Stephn Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This workaround was added to deal with NAPI core and how
it affected dual port shared polling. It turned out not to
be necessary. Stopping device 0 only doesn't stop NAPI from
working completely after that.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make sure that if we ever get a MIB counter overflow interrupt (normally
masked off), that the IRQ is cleared.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When driver can't allocate receive buffer it drops incoming
packet. Keep a counter.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Align the PHY setup of the sky2 driver with the vendor sk98lin (10.0.4.3)
driver. The PHY register settings are mostly black magic, even with access
to the documentation it isn't clear what the right values are. The changes
are mostly comments, the code change only affects the Yukon FE (100 mbit only)
version.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The problems with Gigabyte motherboards are system configuration dependent.
Since it works fine for some users, it doesn't make sense to deprive
them.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
It was agreed that phy-connection-type was a better name for
the interface-type property, so this patch renames it.
Also, the max-speed property name was determined too generic,
and is therefore eliminated in favour of phy-connection-type
derivation logic.
includes corrections to copyright text.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Looks like the new version of this patch has been overlooked,
so I'm resending it.
It just adapts the driver to the new IRQ API
according to what Russell has pointed out.
drivers/net/smc911x.c | 6 ++----
1 files changed, 2 insertions(+), 4 deletions(-)
Signed-off-by: Vitaly Wool <vitalywool@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Turns out we have an old version of firmware that stores the mac address
in 'mac-address' as a string instead of a byte array. All versions that
use local-mac-address should have it as byte array, so no need to do
string parsing for that case.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This caused some very interesting behaviour depending on what happened to
be built at the same time. Add terminating empty entry to the list of IDs.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Interrupt ack fixes
Fix the packet count resets at interrupt time, using the cacheable
packet count status to set number of processed/received packets, since
the ack count is the cumulative number of packets processed, and not
incremental.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some shift values were obviously wrong. Fix them to correspond with
the masks.
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* 'for-linus' of master.kernel.org:/pub/scm/linux/kernel/git/roland/infiniband:
IPoIB/cm: Optimize stale connection detection
IB/mthca: Set cleaned CQEs back to HW ownership when cleaning CQ
IB/mthca: Fix posting >255 recv WRs for Tavor
RDMA/cma: Add check to validate that cm_id is bound to a device
RDMA/cma: Fix synchronization with device removal in cma_iw_handler
RDMA/cma: Simplify device removal handling code
IB/ehca: Disable scaling code by default, bump version number
IB/ehca: Beautify sysfs attribute code and fix compiler warnings
IB/ehca: Remove _irqsave, move #ifdef
IB/ehca: Fix AQP0/1 QP number
IB/ehca: Correctly set GRH mask bit in ehca_modify_qp()
IB/ehca: Serialize hypervisor calls in ehca_register_mr()
IB/ipath: Shadow the gpio_mask register
IB/mlx4: Fix uninitialized spinlock for 32-bit archs
mlx4_core: Remove unused doorbell_lock
net: Trivial MLX4_DEBUG dependency fix.
CONFIG_MLX4_DEBUG works out to a def_bool y for those that have
CONFIG_EMBEDDED set. Make it depend on MLX4_CORE.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Roland Dreier <rolandd@cisco.com>
This patch creates platform_device entries for the Marvell mv64x60
ethernet controller ports, based on information contained in the
device tree.
This driver (like the other mv64x60 drivers) are unusual in that it
works on both the MIPS and PowerPC architectures. Because of that,
the drivers do not support the normal PowerPC of_platform_bus_type.
They support platform_bus_type instead.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Distinguish between the Davicom DM9161A PHY and the DM9161E.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use DMI to add a blacklist of broken boards (so far only one).
Hopefully, the problems will be solved later, and the the whole
blacklist can disappear.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The driver is not ready to support 88e8071 chip.
If this chip is present, system will hang on boot.
So remove it from PCI device id's for now.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If device is not fails during module startup (like unsupported chip
version) then driver would crash dereferencing a null pointer, on shutdown
or suspend/resume.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If the device is fails during module startup for some reason like
unsupported chip version then the driver would crash dereferencing a
null pointer, on shutdown or suspend/resume.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
drivers/net/netxen/netxen_nic_main.c: In function 'netxen_nic_open':
drivers/net/netxen/netxen_nic_main.c:738: warning: 'deprecated_irq_flag' is deprecated (declared at include/linux/interrupt.h:66)
drivers/net/netxen/netxen_nic_main.c:738: warning: 'deprecated_irq_flag' is deprecated (declared at include/linux/interrupt.h:66)
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Change Kconfig objects from "menu, config" into "menuconfig" so
that the user can disable the whole feature without having to
enter the menu first.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use menuconfigs instead of menus, so the whole menu can be disabled at once
instead of going through all options.
Signed-off-by: Jan Engelhardt <jengelh@gmx.de>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Added statistics for link up/down, last link up/down.
2. Statistics for memory allocated/freed.
3. Changed level of some DBG_PRINTs.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
1. Added code to count the number of memory failures.
2. Added watchdog_timer counter.
3. Changed debug level for some DBG_PRINTS.
Signed-off-by: Sreenivasa Honnur <sreenivasa.honnur@neterion.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
made debugfs.c sparse-clean, found an unused function that way
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove the static definition of SUPPORT_BOOT_COMMAND.
Signed-off-by: Holger Schurig <hs4233@mail.mn-solutions.de>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
