Add PPU event-based and cycle-based profiling support to Oprofile for Cell.
Oprofile is expected to collect data on all CPUs simultaneously.
However, there is one set of performance counters per node. There are
two hardware threads or virtual CPUs on each node. Hence, OProfile must
multiplex in time the performance counter collection on the two virtual
CPUs.
The multiplexing of the performance counters is done by a virtual
counter routine. Initially, the counters are configured to collect data
on the even CPUs in the system, one CPU per node. In order to capture
the PC for the virtual CPU when the performance counter interrupt occurs
(the specified number of events between samples has occurred), the even
processors are configured to handle the performance counter interrupts
for their node. The virtual counter routine is called via a kernel
timer after the virtual sample time. The routine stops the counters,
saves the current counts, loads the last counts for the other virtual
CPU on the node, sets interrupts to be handled by the other virtual CPU
and restarts the counters, the virtual timer routine is scheduled to run
again. The virtual sample time is kept relatively small to make sure
sampling occurs on both CPUs on the node with a relatively small
granularity. Whenever the counters overflow, the performance counter
interrupt is called to collect the PC for the CPU where data is being
collected.
The oprofile driver relies on a firmware RTAS call to setup the debug bus
to route the desired signals to the performance counter hardware to be
counted. The RTAS call must set the routing registers appropriately in
each of the islands to pass the signals down the debug bus as well as
routing the signals from a particular island onto the bus. There is a
second firmware RTAS call to reset the debug bus to the non pass thru
state when the counters are not in use.
Signed-off-by: Carl Love <carll@us.ibm.com>
Signed-off-by: Maynard Johnson <mpjohn@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a cpufreq backend driver to enable frequency scaling on cell.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds a module that registers sysfs attributes to CPU and SPU
containing the temperature of the CBE.
They can be found under
/sys/devices/system/spu/cpuX/thermal/temperature[0|1]
/sys/devices/system/spu/spuX/thermal/temperature
The temperature is read from the on-chip temperature sensors.
Signed-off-by: Christian Krafft <krafft@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Reintroduce NODES_SPAN_OTHER_NODES for powerpc
Revert "[PATCH] Remove SPAN_OTHER_NODES config definition"
This reverts commit f62859bb68.
Revert "[PATCH] mm: remove arch independent NODES_SPAN_OTHER_NODES"
This reverts commit a94b3ab7ea.
Also update the comments to indicate that this is still required
and where its used.
Signed-off-by: Andy Whitcroft <apw@shadowen.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Mike Kravetz <kravetz@us.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Mel Gorman <mel@csn.ul.ie>
Acked-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Cc: Christoph Lameter <clameter@sgi.com>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The default configuration file for the MPC8349E-mITX reference board,
mpc834x_itx_defconfig, did not include support for DOS partition table types.
This support is necessary because the hard drive that comes with the ITX
is formatted with this partition table type. Without this config option,
no partitions on the drive can be mounted.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This updates the Maple defconfig to 4 CPUs (along with current defaults)
to support the "tigerwood" 970MP evaluation board.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This make sure that an iseries_defconfig does not inlude
other platforms.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Since the ipr driver now supports SATA and depends on libata,
enable libata to get built.
Signed-off-by: Brian King <brking@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This adds defaults for new configuration options added since
2.6.18 and it enables the option for 64kb pages by default.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
The patch adds MPC8360EMDS board support.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Yin Olivia <hong-hua.yin@freescale.com>
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update defconfig files after libata .config breakage
sed -i 's/CONFIG_SCSI_SATA_/CONFIG_SATA_/;s/CONFIG_SCSI_SATA/CONFIG_ATA/' arch/powerpc/configs/*g
Signed-off-by: Olaf Hering <olaf@aepfle.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
update mpc8349_itx_defconfig and turn off some debug settings
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This makes the 8560 evaluation board fully supported under arch/powerpc,
as the first board with CPM2 SoC peripherals. The brand new devicetree
nodes are introduced (intending to be a subset of the QuiccEngine-equipped
models, with dts sources placed into the kernel according to the new convention.
Assuming all the preceding stuff applied (PAL+fs_enet related+ CPM_UART
update), the both TSEC eth ,FCC Eths, and both SCC UARTs are
working. The relevant drivers are still capable to drive users in ppc,
which was verified with 8272ADS (SCC uart+FCC eth).
This is also verified on mpc8540 and actually make it work (PCI stuff
working as well)
Signed-off-by: Vitaly Bordug <vbordug@ru.mvista.com>
This fixes MPC834x MDS (formerly SYS) and ITX platform code to get IRQ data (including PCI) from the device tree, and to use the new IPIC code.
renamed defconfig (sys -> mds), left one redundant NULL assignment in mpc83xx_pcibios_fixup to keep the compiler happy.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updating the defconfigs for iseries, pseries, and G5. Sticking with
the defaults, with the following exceptions: I've turned off HW_RANDOM
for all three configs. For G5, I've enabled SND_AOA and friends as
modules; this includes the FABRIC_LAYOUT, ONYX, TAS, TOONIE and
SOUNDBUS* config options.
Signed-off-by: Will Schmidt <will_schmidt@vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
I think that most people who use maple_defconfig are doing so for a JS21,
so it might make sense to turn Tigon3 support on by default.
Built and booted on a JS21.
Signed-off-by: Amos Waterland <apw@us.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch fixes the front-LED Kconfig issues I introduced while
creating it. Apparently having a dependency isn't enough to have the
select not evaluated or something like that.
The patch also changes the default configuration for pmac32 select the
default for the LED to be the IDE trigger. While I was at it, I
completely updated the defconfig and also added snd-aoa to it.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Provide default configuration for the Freescale MPC8349E-mITX board, including
the on-board 16MB flash.
Signed-off-by: Kim Phillips <kim.phillips@freescale.com>
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Now that we have the udbg callbacks we can enable XMON by default.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Creates new config variables PPC_CELL_NATIVE and PPC_IBM_CELL_BLADE.
The existing CONFIG_PPC_CELL is now used to denote the generic
Cell processor support.
PPC_CELL = make descends into platforms/cell
PPC_CELL_NATIVE = add bare metal support
PPC_IBM_CELL_BLADE = add blade device drivers, etc.
Also renames spu_priv1.c to spu_priv1_mmio.c.
Signed-off-by: Geoff Levand <geoffrey.levand@am.sony.com>
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable some of the most requested features in defconfig
and refresh with the latest powerpc.git Kconfig files.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This is a first version of support for the Cell BE "Reliability,
Availability and Serviceability" features.
It doesn't yet handle some of the RAS interrupts (the ones described in
iic_is/iic_irr), I'm still working on a proper way to expose these. They
are essentially a cascaded controller by themselves (sic !) though I may
just handle them locally to the iic driver. I need also to sync with
David Erb on the way he hooked in the performance monitor interrupt.
So that's all for 2.6.17 and I'll do more work on that with my rework of
the powerpc interrupt layer that I'm hacking on at the moment.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Haiying Wang <Haiying.Wang@freescale.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Some updates to the pmac32_defconfig to make it more useful:
- Enable LSF (large single files) since we enable LBD (large block devices)
- Enable IPSEC related options
- Enable remaining raid/dm options as modules
- Disable eth1394, I doubt any has that hardware and it has a nasty habit of
auto loading first and skewing network device numbering
- Enable dummy and tun as modules, always useful to have them around
- Enable EHCI, no wonder my usb2 disk was so slow
- Enable USB storage
- Enable ext3 acls
- Disable autofs and enable autofsv4 instead
- Enable nfs v3/v4 client and server. Dont want to be left in the dark ages
of pre v3
- Enable all crypto as modules, things like cryptsetup want some of them
I havent enabled the BCM43xx, perhaps we should now?
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
reflect the changes to Kconfig since the last update.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
This patch adds support for 85xx CDS support to arch/powerpc
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
When we build for the MPC8540 ADS produce a uImage by default.
Updated the defconfig to reflect this as well.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The default configuration in mainline got a little out of
sync with what we use internally.
Signed-off-by: Arnd Bergmann <arnd.bergmann@de.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Enable the onboard IDE driver for p610, p615 and p630.
They have the CD connected to this card. All other RS/6000 systems with this
controller have no connectors and dont need this option.
Signed-off-by: Olaf Hering <olh@suse.de>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Update defconfigs for g5, pseries and generic ppc64. Default choices
for everything, with the following exceptions:
* Enable WINDFARM_PM112 on g5 and ppc64.
* Increase CONFIG_NR_CPUS to 4 in g5_defconfig
* CONFIG_TIGON3=y instead of =m in g5_defconfig
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Updated patch for support for mpc8540_ads in arch/powerpc with a
flat OF device tree. This patch does not yet support PCI or I2C.
Signed-off-by: Becky Bruce <becky.bruce@freescale.com>
Signed-off-by: Jon Loeliger <jdl@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Paul Mackerras <paulus@samba.org>
