- Move ATAPI check-condition handling out of the timeout handler
- Use multi-qc-issue feature to issue REQUEST SENSE ATAPI PACKET
command upon receiving an ATAPI check-condition.
This cleans things up a lot, and eliminates a nasty recursion bug.
scsi_wait_req does not exist any more in the SCSI layer. This patch
makes it so libata can compile again.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
A lot of power packed into a little patch.
This change eliminates the sharing between our controller-wide spinlock
and the SCSI core's Scsi_Host lock. As the locking in libata was
already highly compartmentalized, always referencing our own lock, and
never scsi_host::host_lock.
As a side effect, this change eliminates a deadlock from calling
scsi_finish_command() while inside our spinlock.
The second argument to ata_qc_complete() was being used for two
purposes: communicate the ATA Status register to the completion
function, and indicate an error. On legacy PCI IDE hardware, the latter
is often implicit in the former. On more modern hardware, the driver
often completely emulated a Status register value, passing ATA_ERR as an
indication that something went wrong.
Now that previous code changes have eliminated the need to use drv_stat
arg to communicate the ATA Status register value, we can convert it to a
mask of possible error classes.
This will lead to more flexible error handling in the future.
- move default mode pages to the front of libata-scsi.c
so various functions can access them
- partial annotation of these pages, point out divergence
from sat-r06
- replace various mode page magic numbers with defines
- strengthen MODE SENSE command decoding: handle DBD
bit in cdb, yield block descriptor (per sat-r06) and
handle mode sub pages
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- merge ata_prot_to_cmd() and ata_dev_set_protocol() as
ata_rwcmd_protocol()
- pave road for read/write multiple support
- remove usage of pre-cached command and protocol values and call
ata_rwcmd_protocol() instead
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
==============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
move the initialization of taskfile LBA flags
"ATA_TFLAG_LBA" and "ATA_TFLAG_LBA48 flags"
to the SCSI translation functions
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
=============
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- change "xlat" and "fill" actors in libata-scsi so
they are responsible for SCSI status and sense data
when they return 1. This allows GOOD status or a
specialized error to be set.
- yield an error for mode sense requests for saved
values [sat-r06]
- remove static inlines for ata_bad_scsiop() and
ata_bad_cdb() which are no longer used
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
- add extern ata_scsi_set_sense() to build SCSI
fixed sense data and corresponding SCSI status
Signed-off-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: Jeff Garzik <jgarzik@pobox.com>
1) note urgent bug, that completes command twice
2) only fix up INQUIRY data if the SCSI version is zero (typically
indicates ATAPI MMC-ish device)
3) if there is a problem on the ATA bus, don't bother with REQUEST
SENSE, just directly handle the error based on Status/Error registers.
Since our max_lun is unconditionally set to 1, we might as well
hardcode a LUN 0 probe, rather than a wildcard LUN scan.
The ide-scsi driver sets max_lun to a value greater than under
certain conditions:
if ((drive->id->last_lun & 0x7) != 7)
host->max_lun = (drive->id->last_lun & 0x7) + 1;
else
host->max_lun = 1;
last_lun is Word 126 of IDENTIFY PACKET DEVICE, marked as obsolete
and undocumented in non-ancient specs. We'll leave it out for now.
Should the need arise to support multi-LUN ATAPI devices, we'll
probably want to add the above code.
Finally, there have been reports of REPORT LUNS commands locking up
ATAPI drives. Eliminating the wildcard LUN scan could help reduce
the trouble from problematic drives.
Replace SCSI's legacy "bang at the door" method of probing with one
directly controlled by the underlying ATA transport layer.
We now only call scsi_scan_target() for devices we find, rather than
probing every possible channel/id within a certain range.
ATAPI is getting close to being ready. To increase exposure, we enable
the code in the upstream kernel, but default it to off (present
behavior). Users must pass atapi_enabled=1 as a module option (if
module) or on the kernel command line (if built in) to turn on
discovery of their ATAPI devices.
- changes license of all code from OSL+GPL to plain ole GPL
- except for NVIDIA, who hasn't yet responded about sata_nv
- copyright holders were already contacted privately
- adds info in each driver about where hardware/protocol docs may be
obtained
- where I have made major contributions, updated copyright dates
Fix bugs for unlikely edge cases noticed by Douglas Gilbert:
- When READ(6)/WRITE(6) sector count == 0, treat it as 256 sectors
- For other READ(x)/WRITE(x), when sector count == 0, error.
We don't support successfully completing zero-length transfers at
this time.
