- hrtimers did not use the hrtimer_restart enum and relied on the implict
int representation. Fix the prototypes and the functions using the enums.
- Use seperate name spaces for the enumerations
- Convert hrtimer_restart macro to inline function
- Add comments
No functional changes.
[akpm@osdl.org: fix input driver]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Hook up to hwmon
* show sensor attributes only if hwmon is present
* ... and the board's reference voltage is known
* otherwise be just a touchscreen
- Report voltages per hwmon convention
* measure in millivolts
* voltages are named in[0-8]_input (ugh)
* for 7846 chips, properly range-adjust vBATT/in1_input
Battery measurements help during recharge monitoring. On OSK/Mistral,
the measured voltage agreed with a multimeter to several decimal places.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
We can't depend on the pressure value to determine when the pen was
lifted, so use the GPIO line state instead. This also helps with
chips (like ads7843) that don't have pressure sensors.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Talk to ADS7846 chip using SPI mode 1, which is what the chip
supports: writes on falling clock edge, reads on rising.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Use hrtimer instead of the normal timer, since it provides better
sampling resolution. This will:
- avoid a problem where we have a 1 jiffy poll period and
dynamic tick on
- utilize high resolution HW clocks when they are added to
the hrtimer framework
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
On some LCDs leaving the Vref on provides much better readings.
Signed-off-by: Jarkko Oikarinen <jarkko.oikarinen@nokia.com>
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some LCDs like the LS041Y3 require a customized filtering
logic for reliable readings, so make the filtering function
replacable through platform specific hooks.
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
This improves accuracy of the touchscreen and hwmon sensor readings,
addressing an issue noted by Imre Deak: there's an extra bit written before
the sample (12 bits) gets written out.
It also catches up to various comments, and makes the /proc/interrupts
entry sensible again.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Imre Deak <imre.deak@nokia.com>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Providing more accurate coordinates for thumb press requires additional
steps in the filtering logic:
- Ignore samples found invalid by the debouncing logic, or the ones that
have out of bound pressure value.
- Add a parameter to repeat debouncing, so that more then two consecutive
good readings are required for a valid sample.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
X touchscreen drivers that don't interpret the designated pen up message
assume a pen up event from a pressure value 0. For these we generate a
pressure 0 message along with the pen up message.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Acked-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
The pen down IRQ will toggle during each X,Y,Z measurement cycle.
Even though the IRQ is disabled it will be latched and delivered
when after enable_irq. Thus in the IRQ handler we must avoid
starting a new measurement cycle when such an "unwanted" IRQ happens.
Add a get_pendown_state platform function, which will probably
determine this by reading the current GPIO level of the pen IRQ pin.
Move the IRQ reenabling from the SPI RX function to the timer. After
the last power down message the pen IRQ pin is still active for a
while and get_pendown_state would report incorrectly a pen down state.
When suspending we should check the ts->pending flag instead of
ts->pendown, since the timer can be pending regardless of ts->pendown.
Also if ts->pending is set we can be sure that the timer is running,
so no need to rearm it. Similarly if ts->pending is not set we can
be sure that the IRQ is enabled (and the timer is not).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
- Add disable attribute to support device locking mode where
unintentional touch event shouldn't wake up the system;
- Update comments;
- Add missing spin_lock_init;
- Do device resume with the lock held;
- Do cleanup calls / free memory in the reverse order of initialization.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Sometimes a polling loop had a hard time changing state without
pre-emption enabled. Use msleep instead, it's better anyway.
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Some touchscreens seem to oscillate heavily for a while after touching
the screen. Implement support for sampling the screen until we get two
consecutive values that are close enough.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Submit a seperate request for powering down the ADC in ads7846,
doing it after the last read request. Otherwise some of the read
values are incorrect.
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
It's handy for userspace diagnostics to see the pen down status, to
see whether the touchscreen is "stuck" (shortcircuited).
Signed-off-by: Imre Deak <imre.deak@nokia.com>
Signed-off-by: Juha Yrjola <juha.yrjola@nokia.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
drivers/input/touchscreen/ads7846.c: In function `ads7846_read12_ser':
drivers/input/touchscreen/ads7846.c:207: warning: implicit declaration of function `disable_irq'
drivers/input/touchscreen/ads7846.c:209: warning: implicit declaration of function `enable_irq'
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sparc32:
drivers/input/touchscreen/ads7846.c: In function `ads7846_read12_ser':
drivers/input/touchscreen/ads7846.c:206: warning: implicit declaration of function `disable_irq'
drivers/input/touchscreen/ads7846.c:208: warning: implicit declaration of function `enable_irq'
Cc: Dmitry Torokhov <dtor_core@ameritech.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This updates the ads7846 touchscreen driver:
- to allow faster clocking (this driver doesn't push sample rates);
- bugfixes the conversion of spi_transfer to lists;
- some dma-unsafe command buffers are fixed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
There's no need to have request_irq followed by set_irq_type.
Just use request_irq with the appropriate SA_TRIGGER flags.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This makes the SPI core and its users access transfers in the SPI message
structure as linked list not as an array, as discussed on LKML.
From: David Brownell <dbrownell@users.sourceforge.net>
Updates including doc, bugfixes to the list code, add
spi_message_add_tail(). Plus, initialize things _before_ grabbing the
locks in some cases (in case it grows more expensive). This also merges
some bitbang updates of mine that didn't yet make it into the mm tree.
Signed-off-by: Vitaly Wool <vwool@ru.mvista.com>
Signed-off-by: Dmitry Pervushin <dpervushin@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This updates the ads7864 driver to use the new "spi_driver" struct, and
includes some minor unrelated cleanup.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is a driver for the ADS7846 touchscreen sensor, derived from
the corgi_ts and omap_ts drivers. Key differences from those two:
- Uses the new SPI framework (minimalist version)
- <linux/spi/ads7846.h> abstracts board-specific touchscreen info
- Sysfs attributes for the temperature and voltage sensors
- Uses fewer ARM-specific IRQ primitives
The temperature and voltage sensors show up in sysfs like this:
$ pwd
/sys/devices/platform/omap-uwire/spi2.0
$ ls
bus@ input:event0@ power/ temp1 vbatt
driver@ modalias temp0 vaux
$ cat modalias
ads7846
$ cat temp0
991
$ cat temp1
1177
$
So far only basic testing has been done. There's a fair amount of hardware
that uses this sensor, and which also runs Linux, which should eventually
be able to use this driver.
One portability note may be of special interest. It turns out that not all
SPI controllers are happy issuing requests that do things like "write 8 bit
command, read 12 bit response". Most of them seem happy to handle various
word sizes, so the issue isn't "12 bit response" but rather "different rx
and tx write sizes", despite that being a common MicroWire convention. So
this version of the driver no longer reads 12 bit native-endian words; it
reads 16-bit big-endian responses, then byteswaps them and shifts the
results to discard the noise.
Signed-off-by: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>