More cable funnies
Signed-off-by: Alan Cox <alan@redhat.com>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Previously I reported that the pata_pdc2027x PLL detection changes
in kernel 2.6.22 broke the driver on my PowerMac:
>pata_pdc2027x: Invalid PLL input clock 1691742kHz, give up!
This is followed by a number of errors and speed reduction
steps on the affected ports.
There are two bugs in pata_pdc2027x's PLL detection code:
1. The PLL counter's start value is read before the chip is
put in "test mode". Outside of test mode the counter is
halted, and on the PowerMac the counter is zero because
the chip hasn't been initialised by its BIOS.
The fix is to move the read of the start value to after
test mode is started, but before the mdelay() in test mode.
This also improves the precision of the PLL detection.
2. The code to compute the number of PLL decrements during the
mdelay() in test mode fails to consider that the PLL counter
only is 30 bits wide. If there is a wraparound, it will compute
an incorrect and much too large value. On the PowerMac, the
start count is zero, the end count is a large 30-bit value, so
wraparound occurs and an out of bounds PLL clock is detected.
The fix is to mask the (start - end) computation to 30 bits.
While debugging this I also noticed that pdc_read_counter()
reads the two halves of the 30-bit PLL counter as 16-bit values,
and then combines them as if the halves only are 15 bits wide.
To avoid confusion, the halves should be read as 15-bit values.
This patch implements all three changes. It fixes the PLL detection
failure on my PowerMac, and doesn't cause any regressions on an x86
with an identical card.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If revalidation fails because device has different n_sectors after
configuration the original n_sectors should be restored before failing
revalidation. Without this fix, n_sectors difference will incorrectly
and silently pass revalidation when revalidation is retried.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Adjust libata to ignore errors after spinup
This patch is to ignore errors from the spinup attempt if the drive is
in the "standby id" state.
Signed-off-by: Ryan Power <rpower@sysreset.com>
Acked-by: Mark Lord <liml@rtr.ca>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add TECRA M7 to broken suspend list. Reported by Marie Koreen.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Marie Koreen <kbug@koreen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix several inconsistencies in these drivers WRT reporting the clocks:
- when using DPLL mode, 'pata_hpt37x' driver reported the DPLL frequency as the
PCI clock -- make it properly report both clocks and add the same ability to
the 'pata_hpt3x2n' driver;
- both drivers sometimes use "pata_hpt3*:" and sometimes "hpt3*:" in the
messages -- make them use only the former one;
- the message about failed DPLL stablizatios deserves KERN_ERR and a bang. :-)
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The DPLL tuning code always set up it for 66 MHz due to wrong UltraDMA mask
including mode 5 used to check for the necessity of 66 MHz clocking -- this
caused 66 MHz clock to be used for HPT374 chip that does not tolerate it.
While fixing this, also remove PLL mode from the TODO list -- I don't think
it's still a relevant item.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Maximum supported UDMA mode for AEC6280[R] is UDMA5 (not UDMA4)
and for AEC6880[R] it is UDMA6 (not UDMA5):
* Fix the problem by adding missing struct ata_port_info to artop_init_one().
* Use the right naming (s/626/628/).
* Bump driver version.
Fixes IDE->libata regression, problem was never present in IDE aec62xx driver.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Underneath all the HPT packaging, PCI identifiers, binary driver modules
and stuff you find that ...
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Alan Cox suggested that the solution to the FIXMEs in pata_icside is
to use a private postreset method to detect the lack of devices on a
port, and in such a case, disable the interrupt for the port.
This patch implements such a method, and removes the hard coded
disable of port 0. Tested as working.
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* Fix MWDMA timings setup in sis_old_set_dmamode() and sis_66_set_dmamode().
The old timings were overclocked (even worse behavior than sis5513 IDE driver
which depends on BIOS to program correct timings), the new timings are taken
from the datasheet (they match timings from ATA spec).
* Fix UDMA timings setup in sis_old_set_dmamode().
Misplaced pci_write_config_word() call resulted in UDMA timings never
being set.
* Fix comments for sis_133_early_set_dmamode() and sis_133_set_dmamode():
- only the former function handles early SiS 961 bridges
- both functions lack MWDMA timings setup
* Fix typos in sis_100_set_piomode() and sis_133_set_piomode() comments.
* Bump driver version.
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Tecra M3 to the broken suspend blacklist. Tecra M3 doesn't have
proper DMI_PRODUCT_NAME but has an OEM_STRING instead. Match it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out broken suspend blacklist matching into
piix_broken_suspend().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Seems nobody else is checking/testing this case as it keeps getting
horked.
If we have no BAR4 mapping on an SFF controller this is *NOT* an error,
it just means it isn't doing BMDMA.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Just one version of Linux ago
The PLL code broke - oh no!
But set the right mode
And fix up the code
Makes the PLL timing sync go
[whatever happened to the sailor from Nantucket, hero of many limericks? -jg]
Closes-bug: #8791
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ACPI implementations in several TOSHIBA laptops are weird and burn cpu
cycles for tens of seconds while trying to suspend if the PCI device
for the ATA controller is disabled when the ACPI suspend is called.
This patch uses DMI to match those machines and bypass device disable
on those machines during suspend. As the device needs to be put into
enabled state on resume without affecting PCI enable count, matching
resume callback uses __pci_reenable_device().
This bug is reported in bugzilla bug 7780.
http://bugzilla.kernel.org/show_bug.cgi?id=7780
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Some of the code has been gradually transitioned to using the proper
struct request_queue, but there's lots left. So do a full sweet of
the kernel and get rid of this typedef and replace its uses with
the proper type.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
In most cases, when EH is scheduled, all in-flight commands are
aborted causing EH to kick in immediately. However, in some cases
(especially with PMP), it's unclear which commands are affected by the
error condition and although aborting all in-flight commands work, it
isn't optimal and may cause unnecessary disruption. On the other
hand, waiting for in-flight commands to drain themselves can take up
to 30seconds.
This patch implements EH fast drain to handle such situations. It
gives in-flight commands some time to finish up but doesn't wait for
too long. After EH is scheduled, fast drain timer is started and if
no other completion occurs in ATA_EH_FASTDRAIN_INTERVAL all in-flight
commands are aborted. If any completion occurred in the interval, the
port is given another interval to finish up itself.
Currently ATA_EH_FASTDRAIN_INTERVAL is 3 secs which should be enough
for finishing up most commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If SError isn't accessible, EH can't tell whether hotplug has happened
or not. Report SError read failure with AC_ERR_OTHER and schedule
probing with hardreset. This will be mainly useful for PMPs.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_EHI_HOTPLUGGED is a hint for reset functions indicating the the
port might have gone through hotplug/unplug just before entering EH.
Reset functions modify their behaviors a bit to handle the situation
better - e.g. using longer debouncing delay.
Currently, once HOTPLUG is set, it isn't cleared till the end of EH.
This is unnecessary and makes EH take longer. Clear the HOTPLUGGED
flag after a reset try (successful or not).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
SCSI scan may fail due to memory allocation failure even if EH is not
in progress. Due to use of GFP_ATOMIC in SCSI scan path, allocation
failure isn't too rare especially while probing multiple devices at
once which is the case when a bunch of devices are connected to PMP.
This patch moves SCSI scan failure detetion logic from
ata_scsi_hotplug() to ata_scsi_scan_host() and implement synchronous
scan behavior. The synchronous path sleeps briefly and repeats SCSI
scan if some devices aren't attached properly. It contains robust
retry loop to minimize the chance of device misdetection during boot
and falls back to async retry if everything fails.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Debouncing failure is a good indicator of basic link problem. Use
-EPIPE to indicate debouncing failure and make ata_eh_reset() invoke
sata_down_spd_limit() if the error occurs during reset.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_down_spd_limit() first reads the current SPD from SStatus and
limit the speed to the lower one of one below the current limit or one
below the current SPD in SStatus. SPD may not be accessible or valid
when SPD down is requested making sata_down_spd_limit() fail when it's
most needed.
This patch makes the current SPD cached after each successful reset
and forces GEN I speed (1.5Gbps) if neither of SStatus or the cached
value is valid, so sata_down_spd_limit() is now guaranteed to lower
the speed limit if lower speed is available.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
the onchip SATA type set in the system BIOS:
Device Device ID
SATA in IDE mode 0x4390
SATA in AHCI mode 0x4391
SATA in non-raid5 driver 0x4392
SATA in raid5 driver 0x4393
Although the device ID is different, they use the same AHCI driver
.The attached file is the patch for adding these device
IDs for ATI SB700.
Signed-off-by: henry.su.ati@gmail.com
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make ahci_scr_read/write() handle SCR_NOTIFICATION if the controller
supports it. Also, print "sntf" in the cap line if supported.
While at it, convert eight space into a tab in ahci_print_info().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci_save_initial_config() is responsible for reading, screening the
host CAP register and storing the modified result into hpriv->cap for
the rest of the driver. Move ATA_FLAG_NO_NCQ handling into
ahci_save_initial_config(). It's more consistent this way and the
rest of the driver can always refer to hpriv->cap to determine
configured capability.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Convert ->scr_read/write callbacks to return error code to better
indicate failure. This will help handling of SCR_NOTIFICATION.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When an NCQ command fails, all commands in flight are aborted and the
offending one is reported using log page 10h. Depending on controller
characteristics and LLD implementation, all commands may appear as
having a device error due to shared TF status making it hard to
determine what's actually going on.
This patch adds AC_ERR_NCQ, marks the command reported by log page 10h
with it and print extra "<F>" after the error report for the command
to help distinguishing the offending command.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Requiring LLDs to format multiple error description messages properly
doesn't work too well. Help LLDs a bit by making ata_ehi_push_desc()
insert ", " on each invocation. __ata_ehi_push_desc() is the raw
version without the automatic separator.
While at it, make ehi_desc interface proper functions instead of
macros.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out sil24_do_softreset() which takes @pmp as its last
argument. This will be used to implement sil24_pmp_softreset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out sil24_exec_polled_cmd() from sil24_softreset(). This
will be used to implement sil24_pmp_read/write().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Replace sil24_update_tf() to sil24_read_tf() which reads TF into
passed int result TF argument and can read TFs of PMP links. This
will be used by PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ahci_do_softreset() which takes @pmp as its last
argument. This will be used to implement ahci_pmp_softreset().
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ahci_exec_polled_cmd() from ahci_softreset(). This will
be used to implement ahci_pmp_read/write(). ahci_exec_polled_cmd()
performs reset_engine before returning if the command fails (times
out). This is to improve robustness.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out stop_engine - CLO - start_engine sequence from
ahci_softreset() and ahci_clo() into ahci_reset_engine() and use it in
ahci_softreset() and ahci_post_internal_cmd(). The function will also
be used to prepare for and clean up after PMP register access
commands.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Use deadline instead of fixed timeout for 1st FIS for SRST to improve
robustness of SRST.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add @is_cmd to ata_tf_to_fis(). This controls bit 7 of the second
byte which tells the device whether this H2D FIS is for a command or
not. This cleans up ahci a bit and will be used by PMP.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ata_tf_read was setting HOB bit when lba48 command was submitted, but
was not clearing it before reading "normal" data. As it is only place
which sets HOB bit in control register, and register reads should not
be affected by other bits, let's just clear it when we are done with
reading upper bytes so non-48bit commands do not have to touch ctl
at all.
pata_scc suffered from same problem...
Signed-off-by: Petr Vandrovec <petr@vandrovec.name>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch fixes some issues of the previous patch:
- Use mode_filter() hook to limit ATAPI UDMA mode
- "data loss" warning message
- handling of udma_mask
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Commit df69c9c543 moved only prototype of
out of CONFIG_PM. Move function out as well. Box seems to boot fine.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Yay, the first one from Seagate. 3.ALC firmware is okay. This was
reported by Sam Freed on bugzilla bug 8759.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Sam Freed <sam@freed.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
pata_platform: Fix NULL pointer dereference
pata_platform currently dereferences a NULL pointer in pata_platform_probe()
if pdev->dev.platform_data is set to NULL. This breakage was most likely
introduced by commit 5f45bc5097.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* trim trailing whitespace
* document some flags, registers, and register bits
* fix locking around EDMA on/off and configuration
* continue replacing "constant OP var" with "var OP constant"
* use new pci_try_set_mwi()
Signed-off-by: Jeff Garzik <jeff@garzik.org>
One card submitted by user.
Signed-off-by: Marcin Juszkiewicz <openembedded@hrw.one.pl>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (34 commits)
PCI: Only build PCI syscalls on architectures that want them
PCI: limit pci_get_bus_and_slot to domain 0
PCI: hotplug: acpiphp: avoid acpiphp "cannot get bridge info" PCI hotplug failure
PCI: hotplug: acpiphp: remove hot plug parameter write to PCI host bridge
PCI: hotplug: acpiphp: fix slot poweroff problem on systems without _PS3
PCI: hotplug: pciehp: wait for 1 second after power off slot
PCI: pci_set_power_state(): check for PM capabilities earlier
PCI: cpci_hotplug: Convert to use the kthread API
PCI: add pci_try_set_mwi
PCI: pcie: remove SPIN_LOCK_UNLOCKED
PCI: ROUND_UP macro cleanup in drivers/pci
PCI: remove pci_dac_dma_... APIs
PCI: pci-x-pci-express-read-control-interfaces cleanups
PCI: Fix typo in include/linux/pci.h
PCI: pci_ids, remove double or more empty lines
PCI: pci_ids, add atheros and 3com_2 vendors
PCI: pci_ids, reorder some entries
PCI: i386: traps, change VENDOR to DEVICE
PCI: ATM: lanai, change VENDOR to DEVICE
PCI: Change all drivers to use pci_device->revision
...
It seems irq_on() in ata_bus_reset() and ata_std_postreset()
are leftover of the EDD reset. Remove them.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The last two slots of MAP 00b of ich6m was incorrectly marked as
reserved. This is left over from converting the entry to allow 00b.
This causes no real problem. It only makes the driver print annoying
warning message. Fix it.
[patch also proferred by Pierre Tardy at the end of 2006 -jg]
Signed-off-by: Tejun Heo <htejun@gmail.com>
--
drivers/ata/ata_piix.c | 2 +-
1 file changed, 1 insertion(+), 1 deletion(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add another Maxtor 6B200M0 drive with broken NCQ to the list.
Signed-off-by: Chuck Ebbert <cebbert@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Due to a mistake in test logic, Gen-IIE chips were being treated as
Gen-II chips in some cases. Fix this, and in the process, clean up
IS_50XX/IS_60XX tests to the more uniform IS_GEN_{I,II,IIE} tests.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Continue replacing "CONSTANT & var" tests with "var & CONSTANT"
* Don't clear EDMA_CFG_NCQ_GO_ON_ERR on Gen-IIE, where that bit does
not exist
* Set I/O Id field in descriptor, where present. Appears to work
fine on all versions, even though queueing is still disabled.
* call pci_set_mwi(), to (a) make sure cacheline size is set properly,
and (b) enable MWI transactions
* Remove never-used handling of coalescing interrupt bits (these events
are always masked)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
As suggested by Andrew, add pci_try_set_mwi(), which does not require
return-value checking.
- add pci_try_set_mwi() without __must_check
- make it return 0 on success, errno if the "try" failed or error
- review callers
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Minor cleanups, new definitions, and code movement, preparing for
upcoming new-EH and NCQ changes. This commit shoult not change behavior
at all.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Separate out ata_eh_handle_dev_fail() from ata_eh_recover(). This is
in preparation of ata_link and PMP support.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add Hitachi HDS7250SASUN500G 0621KTAWSD to list of devices with broken NCQ.
Signed-off-by: Prarit Bhargava <prarit@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Workaround for errata A308: turn down the UDMA mode and retry
the DMA command when the data lost condition is detected.
Signed-off-by: Kou Ishizaki <kou.ishizaki@toshiba.co.jp>
Signed-off-by: Akira Iguchi <akira2.iguchi@toshiba.co.jp>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Please warmly welcome the first member from FUJITSU to the prestigious
NCQ spurious completion club.
This is reported by Serge Van Thillo in bugzilla bug 8730.
http://bugzilla.kernel.org/show_bug.cgi?id=8730
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Serge van Thillo <nulleke@hotmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The HPT343/345 (aka 363) is a bit of a warped device. For many setups you
need to access the other registers via BAR4 offsets. PIO is now rock
solid, DMA isn't. Unfortunately the drivers/ide hpt34x driver is
completely broken so doesn't help further debug.
Signed-off-by: Alan Cox <alan@redhat.com>
Cc: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Horkage handling had the following problems.
* dev->horkage was positioned after ATA_DEVICE_CLEAR_OFFSET, so it was
cleared before the device is configured. This broke
HORKAGE_DIAGNOSTIC.
* Some used dev->horkage while others called ata_device_blacklisted()
directly. This was at best confusing.
This patch moves dev->horkage right after dev->flags and set the field
according to the blacklist during device configuration. All users
test against dev->horkage. ata_device_blacklisted() now has only one
user, make it static. While at it, rename it to ata_dev_blacklisted()
for consistency.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The Zip 250 which chokes on MWDMA SET_XFERMODE sometimes have "Floppy"
appeneded to its model number. Quirk it too.
http://bugzilla.kernel.org/show_bug.cgi?id=8563
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Hans de Bruin <bruinjm@xs4all.nl>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
With PCI resource fix up for legacy hosts. We can use the same code
path to allocate IO resources and initialize host for both legacy and
native SFF hosts. Only IRQ requesting needs to be different.
Rename ata_pci_*_native_host() to ata_pci_*_sff_host(), kill all
legacy specific functions and use the renamed functions instead. This
simplifies code a lot.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement suspend and resume routines for mpc52xx ata driver.
Tested on Lite5200b with deep-sleep and low-power (not yet in-tree)
modes.
Signed-off-by: Domen Puncer <domen.puncer@telargo.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch enables hotplugging of SATA devices in the
sata_promise driver. It's been tested successfully on
both first- and second-generation Promise SATA chips:
SATA150 TX2plus, SATAII150 TX2plus, SATAII150 TX4,
SATA300 TX2plus, and SATA300 TX4.
The only quirk I've seen is that hotplugging (insertion)
on the first-generation SATA150 TX2plus requires a lengthier
EH sequence than on the second-generation chips.
On the second-generation chips a simple soft reset seems
to suffice, but on the first-generation chip there's a
"port is slow to respond" after the initial soft reset,
after which libata issues a hard reset, and then the
device is recognised.
The hotplug checks are high up in the interrupt handling
path, not deep down in error_intr as in ahci/sata_sil24.
That's because the chip doesn't signal hotplug status changes
in the per-port status register: instead a global register
contains hotplug control and status flags for all ports.
I considered following the ahci/sata_sil24 structure, but
that would have required non-trivial changes to the interrupt
handling path, so I chose to keep the hotplug changes simple
and unobtrusive.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
This patch depends on the "sata_promise: cleanups" patch.
Changes since the previous version (posted June 19):
- Correct pdc_interrupt() to increment 'handled' also in
the hotplug case. This prevents IRQ_NONE from being
returned when an interrupt only has hotplug events to
handle, which could confuse the kernel's IRQ machinery.
- Added testing on the SATAII150 TX4.
drivers/ata/sata_promise.c | 41 ++++++++++++++++++++++++++++++++++++-----
1 files changed, 36 insertions(+), 5 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If you are using a SiS controller and the BIOS didn't set it up then the
FIFO may be left active when we try and set up the CD. Not convinced this
matters but I'd prefer to be safe
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We should not use cancel_work_sync(delayed_work->work). This works, but not
good. We can use cancel_rearming_delayed_work(), this also simplifies the
code.
Signed-off-by: Oleg Nesterov <oleg@tv-sign.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Indicate whether this is a Generation-I (50xx), Generation-II (60xx),
or Generation-II-E (6042/7042) chip.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ATA_UDMAx masks are self-documenting, and far better than manually
writing in the hex mask.
Note that pata_it8213 mask differed from the comment. Added a FIXME there.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add support for the SATA portion of Marvell's AHCI-compatible chips.
The PATA port capability, also available via AHCI, is disabled until
support is completed.
NCQ and PCI MSI are disabled by default. Marvell says "we use NCQ" in
their drivers but "we do not use PCI MSI." Theoretically that implies
we need to fix ahci.c to work with Marvell NCQ, but one wonders why
Marvell NCQ is any different from other AHCI chips.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Use ATA_UDMA*
* Remove FIXME notations that once served to remind us to verify
that these were indeed the correct UDMA masks. They are.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add ata_dumb_qc_prep and supporting logic so that a driver can just
specify it needs to be helped in this area. 64K entries are split
as with drivers/ide.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sil24_interrupt() loads host->ports[i] into a local variable,
validates it, and then loads the value again in the call to
sil24_host_intr(). This patch replaces the second load by a
reference to the local variable.
This is safe since no side-effects have occurred since the
initial load. It also improves readability since it makes
it clear that the parameter to sil24_host_intr() is the same
value which was just validated.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On some embedded platforms, such as blackfin, the gpio interrupt for
IDE interface is designed to be triggered with high voltage. The gpio
port should be configured properly by set_irq_type() when register
the irq. This patch enable the generic pata platform driver to
accept platform irq flags data.
Signed-off-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch applies some trivial cleanups to sata_promise:
- repair whitespace damage
- correct comment at board_2057x_pata definition
- pull SATAII TX4 support code out to separate functions
- rename ata_nr to ata_no for consistency with libata's port_no
- remove some init-time debug printks (requested by Jeff)
This patch should cause no behavioural changes, except for
the removed printks.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
--
drivers/ata/sata_promise.c | 56 ++++++++++++++++++---------------------------
1 files changed, 23 insertions(+), 33 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix various bugs in pio/mwdma mode programming.
* Control bits in the timing register wasn't cleared properly while
programming PIO mode.
* MWDMA mode programming cleared the wrong part of control bits.
* MWDMA mode programming cleared udma_mask even when the controller
doesn't support UDMA.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Art Haas <ahaas@airmail.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_sx4:
- describe overall driver theory of operation
- add a few constants that will be used in the future
sata_via:
- remove mention of an old-EH function that is going away
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* convert tabs to spaces
* convert some hex numbers to (1 << n) preferred format
* document i2c and timer control register bits
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make it easier to verify which struct initializers are present, by
presenting them in the order in which they are defined in the API
header.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This flag only has meaning in old-EH drivers, and these drivers have
already been converted to the new EH. Remove.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Make the register offset table more maintainable.
From the 'sii-lbt' branch, which enables the LBT chip feature.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ahci: enable sg segment clustering
The specification states that ahci supports segments up to 4MiB in size,
so enable clustering.
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ap->cbl == ATA_CBL_SATA indicates SATA cable while ap->flags &
ATA_FLAG_SATA indicates SATA host port. Till now they always gave the
same result but SATA/PATA bridge handling will change that. Switch to
ATA_FLAG_SATA test if we're testing for host port type.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Implement _GTM/_STM support. acpi_gtm is added to ata_port which
stores _GTM parameters over suspend/resume cycle. A new hook
ata_acpi_on_suspend() is responsible for storing _GTM parameters
during suspend. _STM is executed in ata_acpi_on_resume(). With this
change, invoking _GTF is safe on IDE hierarchy and acpi_sata check
before _GTF is removed.
ata_acpi_gtm() and ata_acpi_stm() implementation is taken from Alan
Cox's pata_acpi implementation. ata_acpi_gtm() is fixed such that the
result parameter is not shifted by sizeof(union acpi_object).
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch reimplements ACPI invocation such that, instead of
exporting ACPI details to the rest of libata, ACPI event handlers -
ata_acpi_on_resume() and ata_acpi_on_devcfg() - are used. These two
functions are responsible for determining whether specific ACPI method
is used and when.
On resume, _GTF is scheduled by setting ATA_DFLAG_ACPI_PENDING device
flag. This is done this way to avoid performing the action on wrong
device device (device swapping while suspended).
On every ata_dev_configure(), ata_acpi_on_devcfg() is called, which
performs _SDD and _GTF. _GTF is performed only after resuming and, if
SATA, hardreset as the ACPI spec specifies. As _GTF may contain
arbitrary commands, IDENTIFY page is re-read after _GTF taskfiles are
executed.
If one of ACPI methods fails, ata_acpi_on_devcfg() retries on the
first failure. If it fails again on the second try, ACPI is disabled
on the device. Note that successful configuration clears ACPI failed
status.
With all feature checks moved to the above two functions,
do_drive_set_taskfiles() is trivial and thus collapsed into
ata_acpi_exec_tfs(), which is now static and converted to return the
number of executed taskfiles to be used by ata_acpi_on_resume(). As
failures are handled properly, ata_acpi_push_id() now returns -errno
on errors instead of unconditional zero.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add missing LOCKING: and RETURNS: to function comment.
* Don't conditionalize warning messages with ata_msg_probe(). Print
directly with KERN_WARNING.
* Drop duplicate debug messages.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch cleans up ata_acpi_exec_tfs() and its friends.
* Rename taskfile_array to ata_acpi_gtf and make it __packed as it's
used as argument to ACPI method, and use pointer to ata_acpi_gtf and
number of taskfiles to represent _GTF taskfiles instead of a pointer
casted into unsigned long and byte count. This makes argument
re-checking in do_drive_set_taskfiles() unnecessary.
* Pointer in void * not in unsigned long.
* Clean up do_drive_get_GTF() error handling and make
do_drive_get_GTF() return number of taskfiles on success, 0 if _GTF
doesn't exist or doesn't contain valid ata. -errno on other errors.
* Remove superflous check for acpi->buffer.pointer.
* Update taskfile_load_raw() such that printed messages look similar
to the messages printed by ata_eh_report().
* s/do_drive_get_GTF/ata_dev_get_GTF/
s/do_drive_set_taskfiles/ata_dev_set_taskfiles/
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
* Add acpi_handle to ata_host and ata_port. Rename
ata_device->obj_handle to ->acpi_handle and move it above such that
it doesn't get cleared on reconfiguration.
* Replace ACPI node association which ata_acpi_associate() which is
called once during host initialization. Unlike the previous
implementation, ata_acpi_associate() uses ATA_FLAG_ACPI_SATA to
choose between IDE or SATA ACPI hierarchy and uses simple child look
up instead of recursive walk to match the nodes. This is way safer
and simpler. Please read the following message for more info.
http://article.gmane.org/gmane.linux.ide/17554
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
PCMCIA doesn't use DMA and as this driver is used on many platforms we
don't want it to fail on those that define the DMA alloc API as a NULL
return
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We got it backwards and now the other detects are fixed it shows up
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
host->irq and host->irq2 should be set before ata_host_register() for
IRQ reporting to work. Move up host->irq assignment in
ata_host_activate() and add it to ata_pci_init_one() native path and
pata_cs5520.
The port info printing in ata_host_register() doesn't fit all the
different controllers. It should probably be moved out to LLDs with
some helpers in the future.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Changed PATA handler for PATA-ports used by sata_sis.
This patch was originally submitted by Jeff Garzik.
Added PCI-ID 1180 for SiS966 Controller in pata_sis.
The 1180 mode is fully compatible to other SiS PATA-controller.
The PCI-ID 1183 is SATA in PATA-emulation, but not fully compatible
to SiS5513/5518. sata_sis.c is forwarding this ID to pata_sis.
1183 is not working if simply added to pata_sis.
This handling fixes issues with SiS968.
Signed-off-by: Uwe Koziolek <uwe.koziolek@gmx.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Another member of HTS5416* family doing spurious NCQ completion.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Enrico Sardi <enricoss@tiscali.it>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The sata_nv driver was missing the change_queue_depth hook in the SCSI host
template which the other NCQ-capable libata drivers had. This made it impossible
to change the queue depth by user request. Add this in.
Signed-off-by: Robert Hancock <hancockr@shaw.ca>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
sata_inic162x can't do LBA48 properly yet and is likely to corrupt
data on drives larger than LBA28 limit. Disable LBA48 devices during
device configuration.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In ata_hsm_qc_complete():
Calling ata_altstatus() after the qc is completed might race with next qc. Remove it.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Recently the PLL input clock of pata_pdc2027x is sometimes detected
higer than expected (e.g. 20.027 MHz compared to 16.714 MHz).
It seems sometimes the mdelay() function is not as precise as it
used to be. Per Alan's advice, HT or power management might affect
the precision of mdelay().
This patch calls gettimeofday() to mesure the time elapsed and
calculate the PLL input clock accordingly.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Mon, 11 Jun 2007 20:28:16 +0200 api wrote:
> Good day,
> When doing make menuconfig one comes across CONFIG_BLK_DEV_SD.
> The help file states that this is for scsi disks.NO MENTION IS MADE THAT
> IT IS NEEDE FOR SATA DISKS AS WELL!
> Would have saved me a lot of time if the help was up to date.
> I hope this can be changed so others can make a kernel for sata systems
> quicker.
From: Randy Dunlap <randy.dunlap@oracle.com>
Add help info for BLK_DEV_SD referring to its use in
SATA or PATA driver configurations.
Add help text for "ATA" indicating that it probably needs
some SCSI config symbols enabled in order to be useful.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
ATA_HORKAGE_DMA_RW_ONLY for TORiSAN is verified to be subset of using
DMA for ATAPI commands which aren't aligned to 16 bytes. As libata
now doesn't use DMA for unaligned ATAPI commands, the horkage is
redundant. Kill it.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The IDE driver used DMA for ATAPI commands if READ/WRITE command is
multiple of sector size or sg command is multiple of 16 bytes. For
libata, READ/WRITE sector alignment is guaranteed by the high level
driver (sr), so we only have to worry about the 16 byte alignment.
This patch makes ata_check_atapi_dma() always request PIO for all data
transfer commands which are not multiple of 16 bytes.
The following reports are related to this problem.
http://bugzilla.kernel.org/show_bug.cgi?id=8605 (confirmed)
http://thread.gmane.org/gmane.linux.kernel/476620 (confirmed)
https://bugzilla.novell.com/show_bug.cgi?id=229260 (probably)
Albert first pointed out the difference between IDE and libata. Kudos
to him.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In atapi_xlat(), prepare qc better before calling
ata_check_atapi_dma() such that ata_check_atapi_dma() can use info
from qc. While at it, reformat weird looking if/else block in the
function.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When EH gives up after repeated exceptions, it doesn't't clear the
PENDING bit on exit which leaves PENDING bit set without EH actually
scheduled. This makes ata_port_wait_eh() to wait forever makes rmmod
hang on such port. Fix it by clearing the flag.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix section mismatch when CONFIG_HOTPLUG=n (but functions are used
for resume):
WARNING: drivers/ata/pata_it821x.o(.text+0x3f): Section mismatch: reference to .init.text: (between 'it821x_reinit_one' and 'it821x_program_udma')
WARNING: drivers/ata/pata_it821x.o(.text+0x691): Section mismatch: reference to .init.text: (between 'it821x_init_one' and 'it821x_passthru_set_dmamode')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
There's no reason to print out hpa related messages when HPA is not
active. Kill the unconditional message and add a warning message
which is printed if HPA size is smaller than the current size.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
prereset() is now allowed to set flag for unsupported reset method.
EH layer is responsible for selecting the fallback. Remove non-sense
warning message.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The attached patch fixes a trivial
mistake in a MODULE_PARAM_DESC of pata_it821x
driver. The parameter name in MODULE_PARAM_DESC
should match the one in module_param_named.
Signed-off-by: Stas Sergeev <stsp@aknet.ru>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
If PORTS_IMPL register is zero, ahci initialize it to full mask
corresponding to nr_ports in the CAP register. hpriv->cap, which is
initialized at the end of the function, is incorrectly used as value
of CAP causing ahci to always override PORTS_IMPL to 0x1 if it's zero.
Fix it.
This fixes a bug where early ich6 ahci can only access the first port.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix parameter name from ata_dev_reread_id() in libata-core.c for kerneldoc.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
More for the NCQ blacklist. One hitachi and one raptor. Other
members of these families of drives are already on the list, so no
surprises.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Code intended to check DMA status was checking DMA command register.
Moreover firmware seems to "forget" to set DMA capable bit for the
slave device (at least in RAID mode but without ITE RAID volumes) so
check device ID for DMA capable bit when deciding whether to use DMA
and remove DMA status check completely.
Thanks to Pavol Simo for the bugreport and testing the initial fix.
This change unfortunately still doesn't fix DMA in RAID mode (which
works fine with IDE it821x) but Alan is working on the missing pieces
(pata_it821x vs libata EH issues).
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Acked-by: Alan Cox <alan@redhat.com>
Cc: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add the MCP73/MCP77 support to PATA driver.
The patch base on kernel 2.6.22-rc4
Signed-off-by: Peer Chen <peerchen@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
After SRST, libata used to wait for nsect/lbal to be set to 1/1 for
the slave device. However, some ATAPI devices don't set nsect/lbal
after SRST and the wait itself isn't too useful as we're gonna wait
for !BSY right after that anyway.
Before reset-seq update, nsect/lbal wait failure used to be ignored
and caused 30sec delay during detection. After reset-seq, all
timeouts are considered error conditions making libata fail to detect
such ATAPI devices.
This patch limits nsect/lbal wait to around 100ms. This should give
acceptable behavior to such ATAPI devices while not disturbing the
heavily used code path too much.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
IOMEGA ZIP 250 ATAPI claims MWDMA0 support but fails SETXFERMODE if
asked to configure itself to MWDMA0. Force PIO.
This fixes bugzilla bug#8497.
Signed-off-by: Tejun Heo <htejun@gmail.com>
Cc: Calvin Walton <calvin.walton@gmail.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
INIT_DEV_PARAMS and SET_MULTI_MODE change the device parameters cached
by libata. Re-read IDENTIFY DEVICE info and update the cached device
paramters when seeing these commands.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Always enforce correct DEV bit since we know which drive the command
is targeted. SAT demands to ignore the DEV bit, too.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Update the ATA passthru protocol numbers according to the new spec.
Signed-off-by: Albert Lee <albertcc@tw.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The controller is not reporting an unlawful type, it is reporting an
invalid type. Illegal specifically means "prohibited by law"
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ata IRQ ack functions are only used when debugging. Unfortunately
almost every controller that calls them can cause crashes in some
configurations as there are missing checks for bmdma presence.
In addition ata_port_start insists of installing DMA buffers and pad
buffers for controllers regardless. The SFF controllers actually need to
make that decision dynamically at controller setup time and all need the
same helper - so we add ata_sff_port_start. Future patches will switch
the SFF drivers to use this.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
