During testing of bcm43xx interference mitigation, two problems were
discovered:
(1) When the MANUALWLAN mode was set, routines _stack_save and _stack_restore
generated assertions that were traced to saving ILT registers with addresses
> 0xFFF. This problem was fixed by adding one bit to the field used for
the offset, and subtracting one bit from the space used for the id.
(2) In MANUALWLAN mode, the IRQ XMIT errors are generated. The cause of these
errors has not yet been located. Any suggestions on debugging this problem
would be greatly appreciated.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch fixes the poll routine for the natsemi driver so that if the
driver detects an RX state machine lockup then no interrupts will be
lost while the driver recovers from that.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The interrupt status register for the natsemi chips is clear on read and
was read unconditionally from both the interrupt and from the NAPI poll
routine, meaning that if the interrupt service routine was called (for
example, due to a shared interrupt) while a NAPI poll was scheduled
interrupts could be missed. This patch fixes that by ensuring that the
interrupt status register is only read by the interrupt handler when
interrupts are enabled from the chip.
It also reverts a workaround for this problem from the netpoll hook and
improves the trace for interrupt events.
Thanks to Sergei Shtylyov <sshtylyov@ru.mvista.com> for spotting the
issue, Mark Huth <mhuth@mvista.com> for a simpler method and Simon
Blake <simon@citylink.co.nz> for testing resources.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The natsemi drivers include functions for enabling and disabling
interrupts from the chip but these are not used in all code paths. This
patch changes the code paths that touch the interrupt enable register to
use the functions. In all cases this adds an extra PCI read to post the
operation but since none of these are in fast paths this shouldn't be
too much of a problem.
Signed-Off-By: Mark Brown <broonie@sirena.org.uk>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: This will fix a softlock seen on some machines.
The reason was too much time was spent waiting for hardware access
to go through.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NetXen: Set the MTU for the right port depending upon the port number
for XG cards.
Signed-off by: Mithlesh Thukral <mithlesh@netxen.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
When bonding does fail over it calls set_mac_address. When this happens
as the result of another port going down, the phy_mutex that is common to
both ports is held, so it deadlocks. Setting the address doesn't need to do
anything that needs the phy_mutex, it already has the RTNL to protect against
other admin actions.
This change just disables the receiver to avoid any hardware confusion
while address is changing.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
NB: driver is choke-full of code that will break on big-endian; as long
as the hardware is onboard-only we can live with that, but sooner or
later that'll need fixing.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
used by ->attach() in pcmcia analog
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Building ibmtr as a module produces a spectacular pile of modpost warnings:
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x450) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x454) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x458) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x45c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4e8) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4ec) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4f0) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x4f4) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x500) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x504) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x508) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:find_turbo_adapters from .text between 'ibmtr_probe_card' (at offset 0x50c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x520) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x524) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x528) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data:ibmtr_portlist from .text between 'ibmtr_probe_card' (at offset 0x534) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x540) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x544) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x548) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.data: from .text between 'ibmtr_probe_card' (at offset 0x54c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x558) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x55c) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x560) and 'ibmtr_reset_timer'
WARNING: drivers/net/tokenring/ibmtr.o - Section mismatch: reference to .init.text:ibmtr_probe1 from .text between 'ibmtr_probe_card' (at offset 0x564) and 'ibmtr_reset_timer'
Fix by making ibmtr_probe an __init function.
While at it, move move ibmtr_probe_card below ibmtr_probe so the protoype
for ibmtr_probe can be deleted.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/tokenring/ibmtr.c | 25 ++++++++++++-------------
1 file changed, 12 insertions(+), 13 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4580) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4584) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x4588) and 'vortex_eisa_remove'
WARNING: drivers/net/3c59x.o - Section mismatch: reference to .init.text: from .text between 'vortex_eisa_probe' (at offset 0x458c) and 'vortex_eisa_remove'
Fixed by:
o move definition of vortex_eisa_driver below the functions it references.
o remove now unnecessary prototypes for vortex_eisa_probe and
vortex_eisa_remove.
o Make vortex_eisa_probe an __init function.
o Make vortex_eisa_remove a __devexit function.
o Wrap vortex_eisa_driver reference to vortex_eisa_remove with
__devexit_p().
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
drivers/net/3c59x.c | 28 +++++++++++++---------------
1 file changed, 13 insertions(+), 15 deletions(-)
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We must exit immediately on a FIFO fill not take the end of packet path
otherwise each underrun in PIO transmit mode causes a runt packet and the
data is lost.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Initialize the timer with the rest of the private-struct.
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Added during bf793295e1
The current code requests a reset but prohibits autoneg, 1000 Mb/s,
100 Mb/s and full duplex. The 8168 does not like it at all.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
On Yukon FE, occasional hardware receive checksum errors are seen.
An early indication of the problem is single bit differences in the two
checksum engines. Use this as a detection mechanism to turn off Rx
checksumming.
Signed-off-by: Stephen Hemminger <shemminger@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Add a wc_enabled flag in the myri10ge_priv instead of relying
on mtrr >= 0.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Do not use 4k rdma request on SGI TIOCE chipset since this
bridge does not support it.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Allocate a specific page and use pci_map_page for dma test instead
of relying on another existing buffer.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a missing error check in myri10ge_allocate_rings() and set status
to -ENOMEM before all actual allocations so that the error path returns
what it should.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
CC [M] drivers/net/netxen/netxen_nic_hw.o
drivers/net/netxen/netxen_nic_hw.c: In function 'netxen_nic_hw_resources':
drivers/net/netxen/netxen_nic_hw.c:231: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'dma_addr_t'
drivers/net/netxen/netxen_nic_hw.c:250: warning: format '%llx' expects type 'long long unsigned int', but argument 2 has type 'dma_addr_t'
u64 is unsigned long so the cast to u64 will result in a warning on the
printf arguments for 64-bit builds. So cast to unsigned long long instead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
This patch sets avoid_D3 for BIOSes known to be broken. Said BIOSes fail
at PXE boot if the chip is in power state D3.
Signed-off-by: Roger Luethi <rl@hellgate.ch>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In the bcm43xx interrupt handler, sanity checks are wrongly done before the
verification that the interrupt is for the bcm43xx.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The frequency to channel routine in bcm43xx requires that the frequency
be in MHz, but that condition is not always met. This patch does the
necessary conversion.
Signed-off-by: Joerg Sommer <joerg@alea.gnuu.de>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
There are three errors in the transcription of the latest revision to the
B6PHY init specifications.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
drivers/net/sis900.c: In function 'sis900_reset_phy':
drivers/net/sis900.c:972: warning: 'status' may be used uninitialized in this function
drivers/net/sis900.c: In function 'sis900_check_mode':
drivers/net/sis900.c:1431: warning: 'status' may be used uninitialized in this function
drivers/net/sis900.c: In function 'sis900_timer':
drivers/net/sis900.c:1467: warning: 'status' may be used uninitialized in this function
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
We were using the platform_device.id field to identify which ethernet
port is used for mv643xx_eth device. This is not generally correct.
It will be incorrect, for example, if a hardware platform uses a single
port but not the first port. Here, we add an explicit port_number field
to struct mv643xx_eth_platform_data.
This makes the mv643xx_eth_platform_data structure required, but that
isn't an issue since all users currently provide it already.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The PCnet32 driver always passed the the size of the largest possible packet
to the pci_dma_sync_single_for_cpu and pci_dma_sync_single_for_device.
This results in a fairly large "colateral damage" in the caches and makes
the flush operation itself much slower. On a system with a 40MHz CPU this
patch increases network bandwidth by about 12%.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Don Fry <pcnet32@verizon.net>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Handle pci_enable_device() failure while resuming, we can safely exit here.
Signed-off-by: Monakhov Dmitriy <dmonakhov@openvz.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a oops on module removal due to deallocating memory before unregistring
driver Fix a NULL pointer dereference when dev_alloc_skb fails
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix a typo, wrap lines on 80-th column, change KERN_ERR to KERN_INFO for
link status message
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Jeff Garzik <jeff@garzik.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Revert 7628b0a8c0. Thomas Bachler
reports:
Commit 7628b0a8c0 (drivers/net/tulip/dmfe:
support basic carrier detection) breaks networking on my Davicom DM9009.
ethtool always reports there is no link. tcpdump shows incoming packets,
but TX is disabled. Reverting the above patch fixes the problem.
Cc: Samuel Thibault <samuel.thibault@ens-lyon.org>
Cc: Jeff Garzik <jeff@garzik.org>
Cc: Valerie Henson <val_henson@linux.intel.com>
Cc: Thomas Bachler <thomas@archlinux.org>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix broken BD processing code.
Signed-off-by: Michael Barkowski <michael.barkowski@freescale.com>
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Fix two issues in this driver's netpoll path: one usual, with spin_unlock_irq()
enabling interrupts which nobody asks it to do (that has been fixed recently in
a number of drivers) and one unusual, with poll_controller() method possibly
causing loss of interrupts due to the interrupt status register being cleared
by a simple read and the interrpupt handler simply storing it, not accumulating.
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
In active-backup mode, the current bonding code duplicates IGMP
traffic to all slaves, so that switches are up to date in case of a
failover from an active to a backup interface. If bonding then fails
back to the original active interface, it is likely that the "active
slave" switch's IGMP forwarding for the port will be out of date until
some event occurs to refresh the switch (e.g., a membership query).
This patch alters the behavior of bonding to no longer flood
IGMP to all ports, and to issue IGMP JOINs to the newly active port at
the time of a failover. This insures that switches are kept up to date
for all cases.
"GOELLESCH Niels" <niels.goellesch@eurocontrol.int> originally
reported this problem, and included a patch. His original patch was
modified by Jay Vosburgh to additionally remove the existing IGMP flood
behavior, use RCU, streamline code paths, fix trailing white space, and
adjust for style.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
The ARP validation code only needs ARPs for the bonding device.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Bonding can erroneously register the same packet_type to receive
ARPs (for use by ARP validation): once at device open time, and once via
sysfs. Since sysfs can change the validate setting (and thus register
or unregister) at any time, a flag is needed to synchronize with device
open in order to avoid double registrations, and the simplest place is
within the packet_type structure itself. Double unregister is not an
issue.
Bug reported by Ulrich Oelmann <ulrich.oelmann@web.de>.
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
I recognized a compile error in latest git:
/here/workdir/git/drivers/net/gianfar.c: In function `gfar_vlan_rx_kill_vid':
/here/workdir/git/drivers/net/gianfar.c:1135: error: structure has no member named `vgrp'
This error was introduced in commit:
commit 6d04e3b04b
...
[VLAN]: Avoid a 4-order allocation.
Signed-off-by: Jan Altenberg <jan@linutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch splits the vlan_group struct into a multi-allocated struct. On
x86_64, the size of the original struct is a little more than 32KB, causing
a 4-order allocation, which is prune to problems caused by buddy-system
external fragmentation conditions.
I couldn't just use vmalloc() because vfree() cannot be called in the
softirq context of the RCU callback.
Signed-off-by: Dan Aloni <da-x@monatomic.org>
Acked-by: Jeff Garzik <jeff@garzik.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Switching HDLC devices from Ethernet-framing mode caused stale ethernet
function assignments within net_device.
Signed-off-by: Krzysztof Halasa <khc@pm.waw.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is based on the assumption that an interface's ifindex is basically
an alias for a local MAC address, so incoming packets now are matched
to sockets based on remote MAC, session id, and ifindex of the
interface the packet came in on/the socket was bound to by connect().
For relayed packets, the socket that's used for relaying is selected
based on destination MAC, session ID and the interface index of the
interface whose name currently matches the name requested by userspace
as the relaying source interface.
Signed-off-by: David S. Miller <davem@davemloft.net>
The information contained within platform_data should be self-contained.
Replace the pointer to a MAC address with the actual MAC address in
struct mv643xx_eth_platform_data.
Signed-off-by: Dale Farnsworth <dale@farnsworth.org>
Signed-off-by: Jeff Garzik <jeff@garzik.org>
