The MDIO bus drivers for the UCC and gianfar ethernet controllers are
essentially the same. There's no reason to duplicate that much code.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SOFT_RESET must be asserted for at least 3 TX clocks in order for it to work
properly. The syncs in the gfar_write() commands have been hiding this, but
we need to guarantee it.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
BD_LENGTH_MASK is supposed to catch the low 16-bits of the status field, not
the low byte. The old way, we would never be able to clean up tx packets with
sizes divisible by 256.
Signed-off-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Many physical NICs let the OS re-program the "hardware" MAC
address. Virtual NICs should allow this too.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
VLAN filtering allows the hypervisor to drop packets from VLANs
that we're not a part of, further reducing the number of extraneous
packets recieved. This makes use of the VLAN virtqueue command class.
The CTRL_VLAN feature bit tells us whether the backend supports VLAN
filtering.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the MAC control virtqueue class to support a MAC
filter table. The filter table is managed by the hypervisor.
We consider the table to be available if the CTRL_RX feature
bit is set. We leave it to the hypervisor to manage the table
and enable promiscuous or all-multi mode as necessary depending
on the resources available to it.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of the RX_MODE control virtqueue class to enable the
set_rx_mode netdev interface. This allows us to selectively
enable/disable promiscuous and allmulti mode so we don't see
packets we don't want. For now, we automatically enable these
as needed if additional unicast or multicast addresses are
requested.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used for RX mode, MAC filter table, VLAN filtering, etc...
The control transaction consists of one or more "out" sg entries and
one or more "in" sg entries. The first out entry contains a header
defining the class and command. Additional out entries may provide
data for the command. The last in entry provides a status response
back from the command.
Virtqueues typically run asynchronous, running a callback function
when there's data in the channel. We can't readily make use of this
in the command paths where we need to use this. Instead, we kick
the virtqueue and spin. The kick causes an I/O write, triggering an
immediate trap into the hypervisor.
Signed-off-by: Alex Williamson <alex.williamson@hp.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The LRO switch is always set to 1 in the rx processing loop.
It breaks the accelerated iSCSI receive traffic.
Fix its computation.
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Cleans uCode key table bit map iwl_clear_stations_table
since all stations are cleared also the key table must be.
Since the keys are not removed properly on suspend by mac80211
this may result in exhausting key table on resume leading
to memory corruption during removal
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (40 commits)
Blackfin arch: Remove outdated code
Blackfin arch: Fix udelay implementation
Blackfin arch: Update Copyright information
Blackfin arch: Add BF561 PPI POLS, POLC Masks
Blackfin arch: Update CM-BF527 kernel config
Blackfin arch: define bfin_memmap as static since it is only used here
Blackfin arch: cplb mananger: use a do...while loop rather than a for loop
Blackfin arch: fix bug - traps test case 19 for exception 0x2d fails
Blackfin arch: add platform device bfin_mii-bus and KSZ8893M switch driver platform resources to board files
Blackfin arch: build jtag tty driver as a module by default
Blackfin arch: fix 2 bugs related to debug
Blackfin arch: Add ANOMALY_05000380 to BF54x to kill the compile warning
Blackfin arch: Fix bug - 561 SMP kernel can't boot from jffs2
Blackfin arch: base SIC_IWR# programming on whether the MMR exists
Blackfin arch: read SYSCR on newer parts that mirror the bits of SWRST in it
Blackfin arch: fixup board init function name
Blackfin arch: drop CONFIG_I2C_BOARDINFO ifdefs
Blackfin arch: bfin_reset->_bfin_reset redirection no longer needed
Blackfin arch: sync reboot handler with version in u-boot
Blackfin arch: Faster Implementation of csum_tcpudp_nofold()
...
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
sparc64: Kill bogus TPC/address truncation during 32-bit faults.
sparc: fixup for sparseirq changes
sparc64: Validate kernel generated fault addresses on sparc64.
sparc64: On non-Niagara, need to touch NMI watchdog in NOHZ mode.
sparc64: Implement NMI watchdog on capable cpus.
sparc: Probe PMU type and record in sparc_pmu_type.
sparc64: Move generic PCR support code to seperate file.
The removed version with the loop registers saved on the stack was
originally intended to workaround the missing toolchain support for
LoopReg Clobbers.
Since our toolchain now supports these there is no point in keeping this
workaround. And since we don't touch LoopRegs anymore we're no longer
subject for ANOMALY_05000312.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid possible overflow during 32*32->32 multiplies.
Reported-by: Marco Reppenhagen <marco.reppenhagen@auerswald.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
use a do...while loop rather than a for loop to get slightly better
optimization and to avoid gcc "may be used uninitialized" warnings ...
we know that the [id]cplb_nr_bounds variables will never be 0, so this
is OK
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Enable null pointer checking for ICPLBs. The code was there but for
some reason I had commented it out at some stage during development.
Should restrict this to 1K since atomic ops start there.
Signed-off-by: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
- unable to single step over emuexcpt instruction
- gdbproxy goes into infinite loop when doing gdb does "next" over
"emuexcpt"
Don't decrement PC after software breakpoint.
Signed-off-by: Jie Zhang <jie.zhang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
bss_l2 section is garbage when the data in this section is used by
_bfin_relocate_l1_mem, so move the zero out function ahead.
Signed-off-by: Graf Yang <graf.yang@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
base SIC_IWR# programming on whether the MMR exists
rather than having to maintain another list of processors
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Drop CONFIG_I2C_BOARDINFO ifdefs as the common i2c header handles this
already by stubbing things out
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
Avoid conditional branch instructions during carry bit additions.
Special thanks to Bernd.
Simplify: Use ((len + proto) << 8) like every other __LITTLE_ENDIAN__ machine
Cc: Bernd Schmidt <bernds_cb1@t-online.de>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
[Mike Frysinger <vapier.adi@gmail.com>:
- setup P_DEFAULT_BOOT_SPI_CS for every arch based on
the default bootrom behavior and convert all our boards
to it
- revert previous anomaly change ... bf51x is not affected
by anomaly 05000353]
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
remove subscribers-only marking as the list is
automatically & silently moderated for people
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
merge more of the bf54x and !bf54x gpio code together to
cut down on #ifdef mess
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
According to the documentation gpio_free should only be called from task
context only. To make this more explicit add a might sleep to all
implementations.
This patch changes the gpio_free implementations for the blackfin
architecture.
Signed-off-by: Uwe Kleine-Koenig <ukleinek@strlen.de>
Cc: David Brownell <david-b@pacbell.net>
Acked-by: Bryan Wu <cooloney@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Make sure we don't accidently re-enable interrupts if we are being
called in atomic context
Signed-off-by: Robin Getz <rgetz@blackfin.uclinux.org>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
when requesting a GPIO for the first time, the POLAR setting is not
set to a sane state. this can lead to indeterminate behavior that
cannot be resolved without an explicit write to the Blackfin port POLAR
register.
when requesting a GPIO for the first time via gpio_request(), the POLAR
setting for the GPIO in question should be set to sane state. this
should occur if the GPIO has not been allocated in any other way.
some examples:
- when doing something like "request_irq(); gpio_request();" on the
same GPIO, the POLAR setting should not be reset.
- when doing "gpio_request(); gpio_request();" on the same GPIO, the
POLAR setting should be reset only the first time and not the second.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
On BF561 EBIU_SDGCTL bit 31 controls the SDRAM external data
path width, typically set 0 for a 32-bit bus width. On other
Blackfin derivatives this bit should be set by default.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Bryan Wu <cooloney@kernel.org>
