Add the new ID 0x132a and configure the new PCI Diva console port. This
device supports only 1 single console UART.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Tested by Wolfgang Denk with this device:
00:0f.0 Network controller: PLX Technology, Inc. PCI <-> IOBus Bridge (rev 01)
Subsystem: Exsys EX-4055 4S(16C550) RS-232
Control: I/O+ Mem+ BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin A routed to IRQ 10
Region 0: Memory at 80100000 (32-bit, non-prefetchable) [size=128]
Region 1: I/O ports at 7080 [size=128]
Region 2: I/O ports at 7400 [size=32]
00:0f.0 Class 0280: 10b5:9050 (rev 01)
Subsystem: d84d:4055
Results with this patch:
Serial: 8250/16550 driver $Revision: 1.90 $ 32 ports, IRQ sharing enabled
ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
PCI: Found IRQ 10 for device 0000:00:0f.0
ttyS4 at I/O 0x7400 (irq = 10) is a 16550A
ttyS5 at I/O 0x7408 (irq = 10) is a 16550A
ttyS6 at I/O 0x7410 (irq = 10) is a 16550A
ttyS7 at I/O 0x7418 (irq = 10) is a 16550A
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The modem is said to work with belows addition to pnp_dev_table[]:
http://bugs.debian.org/cgi-bin/bugreport.cgi?bug=296011
Signed-off-by: maximilian attems <janitor@sternwelten.at>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Argument does not agree.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Lothar Wassmann
The function serial_pxa_set_termios() is calling uart_update_timeout()
with the baud rate divisor as third parameter, while
uart_update_timeout() expects the baud rate in this place.
This results in a bogus port->timeout which is proportional to the
baud rate.
Signed-off-by: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Ben Dooks
The s3c2410 serial driver is missing static declerations
on several functions that are not exported, and have no
need of being exported outside the driver
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Incorrect uart_write_wakeup() calls cause reference to a
NULL tty pointer in sunsab and sunzilog serial drivers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Ben Dooks
Initialise the driver's .owner field so that
the device driver can be referenced to the
module that owns it
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The lock is not held when calling this function, so we
shouldn't drop then reacquire it.
Based upon a report from Jim MacBaine.
Signed-off-by: David S. Miller <davem@davemloft.net>
Patch from Vincent Sanders
When building the mx1ads ARM platforms the serial driver fails to compile
with GCC 4.01 due to extern/static ambiguity.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This change removes a bogus error message from the IOC4 serial driver
interrupt handler.
This error message is bogus for two reasons. First, it can never occur
given that current code takes care to initialize IOC4 in such a way that
these "unknown" interrupts could never occur. Second, this code fails to
take into account that other drivers can share the IOC4 interrupt mechanism
through SA_SHIRQ, and thus this driver is not in-fact "all-knowing".
Finally, this error message triggers every time some "unknown" interrupt
occurs -- it's not rate limited or repetition limited in any way, thereby
effectively denying use of the console device. Given its bogosity in the
first place, it's best to just get rid of it entirely.
Acked-by: Pat Gefre <pfg@sgi.com>
Signed-off-by: Brent Casavant <bcasavan@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It's pointless to include mach-types.h if you're not going to use
anything from it. These references were removed as a result of:
grep -lr 'asm/mach-types\.h' . | xargs grep -L 'machine_is_\|MACH_TYPE_\|MACHINE_START\|machine_type'
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add new ID to serial_cs.c; the CIS fimware override is available by the
manufacturer at http://www.sierrawireless.com . Remember to name the CIS
binary SW_7xx_SER.cis and to put it into /lib/firmware/
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
Patch from Ben Dooks
Fix the following warnings produced from
drivers/char/s3c2410.c.
drivers/serial/s3c2410.c:757: warning: 'clk' may be used uninitialized
drivers/serial/s3c2410.c:756: warning: 'clksrc' may be used uninitialized
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix up some pm_message_t types
Signed-Off-By: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Patch from Vincent Sanders
When building the ARM platforms several serial drivers fail to compile
with GCC 4.01 due to extern/static ambiguity.
Signed-off-by: Vincent Sanders <vince@arm.linux.org.uk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add support for the new Freescale 523x processor family to ColdFire
serial driver. Also set different default baud rate for MOD5272
board.
Signed-off-by: Greg Ungerer <gerg@uclinux.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Support for the new RBHMA4500 eval board for the TX4938. General update
from the 8250 ancestor of this driver. Replace use of deprecated
interfaces.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rather than hard-coding the platform device IDs, enumerate them.
We don't particularly care about the actual ID we get, just as
long as they're unique.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
asm/segment.h varies greatly on different architectures but is clearly
deprecated. Removing all non-architecture consumers will make it easier
for us to get ride of asm/segment.h all together.
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
this is the last serial driver not using initcalls.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Cc: <jeff@uclinux.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
sunsu had been broken by ->stop_tx/->start_tx API changes.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
This adds type-checking to pm_message_t, so that people can't confuse it
with int or u32. It also allows us to fix "disk yoyo" during suspend (disk
spinning down/up/down).
[We've tried that before; since that cpufreq problems were fixed and I've
tried make allyes config and fixed resulting damage.]
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Alexander Nyberg <alexn@telia.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Base addess register for SMC 1 and 2 are never initialized. This means
that they will not work unless a bootloader already configured them.
The DPRAM already have space reserved, this patch just makes sure the base
addess register is updated correctly on initialization.
Signed-off-by: Rune Torgersen <runet@innovsys.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
use schedule_timeout instead of direct call to schedule
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The 2nd serial port on the MPC8560 ADS was not being configured correctly
and thus could not be used as a console. Updated the defconfig for the
board to configure the proper SCC channel for the 2nd serial port.
Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
Signed-off-by: Kumar Gala <kumar.gala@freescale.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pre-format the IO part of the ttyS printks, and prefix them with
KERN_INFO to avoid bootsplash corruption.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It seems we can simply kill these dummies with this patch.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Patch from Sascha Hauer
This patch adds support for setting and getting RTS / CTS via
set_mtctrl / get_mctrl functions.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The start_tx and stop_tx methods were passed a flag to indicate
whether the start/stop was from the tty start/stop callbacks, and
some drivers used this flag to decide whether to ask the UART to
immediately stop transmission (where the UART supports such a
feature.)
There are other cases when we wish this to occur - when CTS is
lowered, or if we change from soft to hard flow control and CTS
is inactive. In these cases, this flag was false, and we would
allow the transmitter to drain before stopping.
There is really only one case where we want to let the transmitter
drain before disabling, and that's when we run out of characters
to send.
Hence, re-jig the start_tx and stop_tx methods to eliminate this
flag, and introduce new functions for the special "disable and
allow transmitter to drain" case.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
