This fixes a bug introduced in 2.6.18.
If a drive is added to a raid1 using older tools (mdadm-1.x or raidtools)
then it will be included in the array without any resync happening.
It has been submitted for 2.6.18.1.
Signed-off-by: Neil Brown <neilb@suse.de>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This changes two if() BUG(); usages to BUG_ON(); so people
can disable it safely.
Signed-off-by: Eric Sesterhenn <snakebyte@gmx.de>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Once upon a time we needed to fixed limit to the number of md devices,
probably because we preallocated some array. This need no longer exists, but
we still have an arbitrary limit.
So remove MAX_MD_DEVS and allow as many devices as we can fit into the 'minor'
part of a device number.
Also remove some useless noise at init time (which reports MAX_MD_DEVS) and
remove MD_THREAD_NAME_MAX which hasn't been used for a while.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It is possible to request a 'check' of an md/raid array where the whole array
is read and consistancies are reported.
This uses the same mechanisms as 'resync' and so reports in the kernel logs
that a resync is being started. This understandably confuses/worries people.
Also the text in /proc/mdstat suggests a 'resync' is happen when it is just a
check.
This patch changes those messages to be more specific about what is happening.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add a new sysfs interface that allows the bitmap of an array to be dirtied.
The interface is write-only, and is used as follows:
echo "1000" > /sys/block/md2/md/bitmap
(dirty the bit for chunk 1000 [offset 0] in the in-memory and on-disk
bitmaps of array md2)
echo "1000-2000" > /sys/block/md1/md/bitmap
(dirty the bits for chunks 1000-2000 in md1's bitmap)
This is useful, for example, in cluster environments where you may need to
combine two disjoint bitmaps into one (following a server failure, after a
secondary server has taken over the array). By combining the bitmaps on
the two servers, a full resync can be avoided (This was discussed on the
list back on March 18, 2005, "[PATCH 1/2] md bitmap bug fixes" thread).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Instead of magic numbers (0,1,2,3) in sb_dirty, we have
some flags instead:
MD_CHANGE_DEVS
Some device state has changed requiring superblock update
on all devices.
MD_CHANGE_CLEAN
The array has transitions from 'clean' to 'dirty' or back,
requiring a superblock update on active devices, but possibly
not on spares
MD_CHANGE_PENDING
A superblock update is underway.
We wait for an update to complete by waiting for all flags to be clear. A
flag can be set at any time, even during an update, without risk that the
change will be lost.
Stop exporting md_update_sb - isn't needed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch contains the scheduled removal of the START_ARRAY ioctl for md.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If we
- shut down a clean array,
- restart with one (or more) drive(s) missing
- make some changes
- pause, so that they array gets marked 'clean',
the event count on the superblock of included drives
will be the same as that of the removed drives.
So adding the removed drive back in will cause it
to be included with no resync.
To avoid this, we only update the eventcount backwards when the array
is not degraded. In this case there can (should) be no non-connected
drives that we can get confused with, and this is the particular case
where updating-backwards is valuable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
During early MD setup (superblock reading), we don't have a personality yet.
But the error-handling code tries to dereference mddev->pers. Fix.
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The ioctl requires CAP_SYS_ADMIN, so sysfs should too. Note that we don't
require CAP_SYS_ADMIN for reading attributes even though the ioctl does.
There is no reason to limit the read access, and much of the information is
already available via /proc/mdstat
Cc: Chris Wright <chrisw@sous-sol.org>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Some places we use number (0660) someplaces names (S_IRUGO). Change all
numbers to be names, and change 0655 to be what it should be.
Also make some formatting more consistent.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We introduced 'io_sectors' recently so we could count the sectors that causes
io during resync separate from sectors which didn't cause IO - there can be a
difference if a bitmap is being used to accelerate resync.
However when a speed is reported, we find the number of sectors processed
recently by subtracting an oldish io_sectors count from a current
'curr_resync' count. This is wrong because curr_resync counts all sectors,
not just io sectors.
So, add a field to mddev to store the curren io_sectors separately from
curr_resync, and use that in the calculations.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array is started we start one or two threads (two if there is a
reshape or recovery that needs to be completed).
We currently start these *before* the array is completely set up and in
particular before queue->queuedata is set. If the thread actually starts
very quickly on another CPU, we can end up dereferencing queue->queuedata
and oops.
This patch also makes sure we don't try to start a recovery if a reshape is
being restarted.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This has to be done in ->load_super, not ->validate_super
Without this, hot-adding devices to an array doesn't always
work right - though there is a work around in mdadm-2.5.2 to
make this less of an issue.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Teach special (recursive) locking code to the lock validator.
Effects on non-lockdep kernels:
- the introduction of the following function variants:
extern struct block_device *open_partition_by_devnum(dev_t, unsigned);
extern int blkdev_put_partition(struct block_device *);
static int
blkdev_get_whole(struct block_device *bdev, mode_t mode, unsigned flags);
which on non-lockdep are the same as open_by_devnum(), blkdev_put()
and blkdev_get().
- a subclass parameter to do_open(). [unused on non-lockdep]
- a subclass parameter to __blkdev_put(), which is a new internal
function for the main blkdev_put*() functions. [parameter unused
on non-lockdep kernels, except for two sanity check WARN_ON()s]
these functions carry no semantical difference - they only express
object dependencies towards the lockdep subsystem.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make needlessly global code static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Cc: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It appears in /sys/mdX/md/dev-YYY/state
and can be set or cleared by writing 'writemostly' or '-writemostly'
respectively.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The md/dev-XXX/state file can now be written:
"faulty" simulates an error on the device
"remove" removes the device from the array (if it is not busy)
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows the state of an md/array to be directly controlled via sysfs and
adds the ability to stop and array without tearing it down.
Array states/settings:
clear
No devices, no size, no level
Equivalent to STOP_ARRAY ioctl
inactive
May have some settings, but array is not active
all IO results in error
When written, doesn't tear down array, but just stops it
suspended (not supported yet)
All IO requests will block. The array can be reconfigured.
Writing this, if accepted, will block until array is quiescent
readonly
no resync can happen. no superblocks get written.
write requests fail
read-auto
like readonly, but behaves like 'clean' on a write request.
clean - no pending writes, but otherwise active.
When written to inactive array, starts without resync
If a write request arrives then
if metadata is known, mark 'dirty' and switch to 'active'.
if not known, block and switch to write-pending
If written to an active array that has pending writes, then fails.
active
fully active: IO and resync can be happening.
When written to inactive array, starts with resync
write-pending (not supported yet)
clean, but writes are blocked waiting for 'active' to be written.
active-idle
like active, but no writes have been seen for a while (100msec).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- record the 'event' count on each individual device (they
might sometimes be slightly different now)
- add a new value for 'sb_dirty': '3' means that the super
block only needs to be updated to record a clean<->dirty
transition.
- Prefer odd event numbers for dirty states and even numbers
for clean states
- Using all the above, don't update the superblock on
a spare device if the update is just doing a clean-dirty
transition. To accomodate this, a transition from
dirty back to clean might now decrement the events counter
if nothing else has changed.
The net effect of this is that spare drives will not see any IO requests
during normal running of the array, so they can go to sleep if that is what
they want to do.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When an array has a bitmap, a device can be removed and re-added and only
blocks changes since the removal (as recorded in the bitmap) will be resynced.
It should be possible to do a similar thing to arrays without bitmaps. i.e.
if a device is removed and re-added and *no* changes have been made in the
interim, then the add should not require a resync.
This patch allows that option. This means that when assembling an array one
device at a time (e.g. during device discovery) the array can be enabled
read-only as soon as enough devices are available, but extra devices can still
be added without causing a resync.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
md/bitmap modifies i_writecount of a bitmap file to make sure that no-one else
writes to it. The reverting of the change is sometimes done twice, and there
is one error path where it is omitted.
This patch tidies that up.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When "mdadm --grow /dev/mdX --bitmap=none" is used to remove a filebacked
bitmap, the bitmap was disconnected from the array, but the file wasn't closed
(until the array was stopped).
The file also wasn't closed if adding the bitmap file failed.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch makes the needlessly global md_print_devices() static.
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
For a while we have had checkpointing of resync. The version-1 superblock
allows recovery to be checkpointed as well, and this patch implements that.
Due to early carelessness we need to add a feature flag to signal that the
recovery_offset field is in use, otherwise older kernels would assume that a
partially recovered array is in fact fully recovered.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
At shutdown, we switch all arrays to read-only, which creates a message for
every instantiated array, even those which aren't actually active.
So remove the message for non-active arrays.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
When a md array has been idle (no writes) for 20msecs it is marked as 'clean'.
This delay turns out to be too short for some real workloads. So increase it
to 200msec (the time to update the metadata should be a tiny fraction of that)
and make it sysfs-configurable.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This warning was slightly useful back in 2.2 days, but is more an annoyance
now. It makes it awkward to add new ioctls (that we we are likely to do that
in the current climate, but it is possible).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
From: NeilBrown <neilb@suse.de>
If an error is reported by a drive in a RAID array (which is done via
bi_end_io - in interrupt context), we call md_error and md_new_event which
calls sysfs_notify. However sysfs_notify grabs a mutex and so cannot be
called in interrupt context.
This patch just creates a variant of md_new_event which avoids the sysfs
call, and uses that. A better fix for later is to arrange for the event to
be called from user-context.
Note: avoiding the sysfs call isn't a problem as an error will not, by
itself, modify the sync_action attribute. (We do still need to
wake_up(&md_event_waiters) as an error by itself will modify /proc/mdstat).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
otherwise we get nasty messages about locks not being released.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We should be able to write 'repair' to /sys/block/mdX/md/sync_action,
however due to and inverted test, that always given EINVAL.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
- fix mddev_lock() usage bugs in md_attr_show() and md_attr_store().
[they did not anticipate the possibility of getting a signal]
- remove mddev_lock_uninterruptible() [unused]
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
It works like this:
Open the file
Read all the contents.
Call poll requesting POLLERR or POLLPRI (so select/exceptfds works)
When poll returns,
close the file and go to top of loop.
or lseek to start of file and go back to the 'read'.
Events are signaled by an object manager calling
sysfs_notify(kobj, dir, attr);
If the dir is non-NULL, it is used to find a subdirectory which
contains the attribute (presumably created by sysfs_create_group).
This has a cost of one int per attribute, one wait_queuehead per kobject,
one int per open file.
The name "sysfs_notify" may be confused with the inotify
functionality. Maybe it would be nice to support inotify for sysfs
attributes as well?
This patch also uses sysfs_notify to allow /sys/block/md*/md/sync_action
to be pollable
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And remove the comments that were put in inplace of a fix too....
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
... being careful that mutex_trylock is inverted wrt down_trylock
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Semaphore to mutex conversion.
The conversion was generated via scripts, and the result was validated
automatically via a script as well.
Signed-off-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Cc: Neil Brown <neilb@cse.unsw.edu.au>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
An md array can be asked to change the amount of each device that it is using,
and in particular can be asked to use the maximum available space. This
currently only works if the first device is not larger than the rest. As
'size' gets changed and so 'fit' becomes wrong. So check if a 'fit' is
required early and don't corrupt it.
Signed-off-by: Doug Ledford <dledford@redhat.com>
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows user-space to access data safely. This is needed for raid5
reshape as user-space needs to take a backup of the first few stripes before
allowing reshape to commence.
It will also be useful in cluster-aware raid1 configurations so that all
cluster members can leave a section of the array untouched while a
resync/recovery happens.
A 'start' and 'end' of the suspended range are written to 2 sysfs attributes.
Note that only one range can be suspended at a time.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This allows reshape to be triggerred via sysfs (which is the only way to start
it happening).
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
check_reshape checks validity and does things that can be done instantly -
like adding devices to raid1. start_reshape initiates a restriping process to
convert the whole array.
Signed-off-by: Neil Brown <neilb@suse.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
