This was introduced by v2.6.34-rc1~38:
4c014e8 (rtc/mc13783: protect rtc {,un}registration by mc13783 lock)
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reported-by: Dan Carpenter <error27@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Without this patch /sys/class/rtc/$CONFIG_RTC_HCTOSYS_DEVICE/hctosys
contains a 1 (meaning "This rtc was used to initialize the system clock")
even if reading the time at bootup failed.
Moreover change error handling in rtc_hctosys() to use goto and so reduce
the indention level.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
MAX8925 is a PMIC that contains RTC component.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Unlike the wm8350-custom code genirq nests enable and disable calls
so we can't just unconditionally mask or unmask the interrupt,
we need to remember the state we set and only mask or unmask when
there is a real change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: rtc-linux@googlegroups.com
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The else part of the if statement is indented but does not have braces
around it. It clearly should since it uses clk_enable and clk_disable
which are supposed to balance.
Signed-off-by: James Hogan <james@albanarts.com>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is to protect from interrupt handlers using an unregistered rtc
device.
To assert that the reset irq is considered now before the rtc is
registered the corresponding status is checked before.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
mc13783_ackirq, mc13783_unmask and mc13783_mask are deprecated, use the
drop in replacements with the nicer names.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The idr should be destroyed when the module is unloaded. Found with
kmemleak.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nokia.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: stable <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning of
the declaration specifiers in a declaration is an obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Memset should be given the size of the structure, not the size of the
pointer.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
T *x;
expression E;
@@
memset(x, E, sizeof(
+ *
x))
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The function pcf2123_remove is used only wrapped by __devexit_p so define
it using __devexit.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Christian Pellegrin <chripell@fsfe.org>
Cc: Chris Verges <chrisv@cyberswitching.com>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix issue with rtc device not getting unregistered in probe error path.
Use the devres managed resource functions in the probe routine to cleanup
the error path.
Use sysfs_{create/remove}_group to add/remove the sysfs files.
Reduces the text size by 132 bytes, increases data by 12 bytes:
text data bss dec hex filename
- 937 124 0 1061 425 rtc-ep93xx.o
+ 805 136 0 941 3ad rtc-ep93xx.o
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Free pdata before exit. Found by cppcheck.
[yuasa@linux-mips.org: add missing iounmap()]
Signed-off-by: Alexander Beregalov <a.beregalov@gmail.com>
Reviewed-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc Yoichi Yuasa <yuasa@linux-mips.org>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for MPC5121 real time clock module.
Signed-off-by: John Rigby <jcrigby@gmail.com>
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Wolfgang Denk <wd@denx.de>
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This extends the existing PrimeCell PL031 driver with support for
the ST Microelectronics and ST-Ericsson derivatives, in a first
and second version as used on the Nomadik and U8500 platforms.
It also rids the old ioctl() alarm on/off functions in favor of
the new .alarm_irq_enable field of the RTC class ops.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-linus: (71 commits)
MIPS: Lasat: Fix botched changes to sysctl code.
RTC: rtc-cmos.c: Fix warning on MIPS
MIPS: Cleanup random differences beween lmo and Linus' kernel.
MIPS: No longer hardwire CONFIG_EMBEDDED to y
MIPS: Fix and enhance built-in kernel command line
MIPS: eXcite: Remove platform.
MIPS: Loongson: Cleanups of serial port support
MIPS: Lemote 2F: Suspend CS5536 MFGPT Timer
MIPS: Excite: move iodev_remove to .devexit.text
MIPS: Lasat: Convert to proc_fops / seq_file
MIPS: Cleanup signal code initialization
MIPS: Modularize COP2 handling
MIPS: Move EARLY_PRINTK to Kconfig.debug
MIPS: Yeeloong 2F: Cleanup reset logic using the new ec_write function
MIPS: Yeeloong 2F: Add LID open event as the wakeup event
MIPS: Yeeloong 2F: Add basic EC operations
MIPS: Move several variables from .bss to .init.data
MIPS: Tracing: Make function graph tracer work with -mmcount-ra-address
MIPS: Tracing: Reserve $12(t0) for mcount-ra-address of gcc 4.5
MIPS: Tracing: Make ftrace for MIPS work without -fno-omit-frame-pointer
...
RTC core won't allow wakeup alarms to be set if RTC devices' parent (i.e.
i2c_client or spi_device) isn't wakeup capable.
For I2C devices there is I2C_CLIENT_WAKE flag exists that we can pass via
board info, and if set, I2C core will initialize wakeup capability. For
SPI devices there is no such flag at all.
I believe that it's not platform code responsibility to allow or disallow
wakeups, instead, drivers themselves should set the capability if a device
can trigger wakeups.
That's what drivers/base/power/sysfs.c says:
* It is the responsibility of device drivers to enable (or disable)
* wakeup signaling as part of changing device power states, respecting
* the policy choices provided through the driver model.
I2C and SPI RTC devices send wakeup events via interrupt lines, so we
should set the wakeup capability if IRQ is routed.
Ideally we should also check irq for wakeup capability before setting
device's capability, i.e.
if (can_irq_wake(irq))
device_set_wakeup_capable(&client->dev, 1);
But there is no can_irq_wake() call exist, and it is not that trivial to
implement it for all interrupts controllers and complex/cascaded setups.
drivers/base/power/sysfs.c also covers these cases:
* Devices may not be able to generate wakeup events from all power
* states. Also, the events may be ignored in some configurations;
* for example, they might need help from other devices that aren't
* active
So there is no guarantee that wakeup will actually work, and so I think
there is no point in being pedantic wrt checking IRQ wakeup capability.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
All callsites of x1205_set_datetime() want the date to be set as well, so
remove the flag parameter and set it unconditionally.
Signed-off-by: Johannes Weiner <jw@emlix.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's possible to have RTC irq shared with other device (e.g.
mpc8349e-mitx board shares ds1339 irq with phy one). Handle this in
driver.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This switches __raw_[read|write]l() for plain [read|write]l in the PL031
RTC driver. The sister driver for PL030 use the simple accessors as most
PrimeCell drivers.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds basic support for Texas Instruments BQ32000 I2C RTC. Only
time reading/writing is implemented. Advanced features, such as trickle
charger and crystal calibration are not supported.
Signed-off-by: Piotr Ziecik <kosmo@semihalf.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The rtc-omap driver currently assumes that the rtc's registers are at a
fixed address and already mapped into virtual memory space. Remove those
assumptions so the same driver can be used for similar devices that reside
at different physical addresses (e.g., TI's DA8xx/OMAP-L13x SoC's).
Also allow the possibility for the timer and alarm interrupts to use the
same IRQ.
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Acked-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver provides support for the RTC part integrated into the
Freescale MC13783 PMIC and bases on patch created earlier by Sascha
Hauer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Valentin Longchamp <valentin.longchamp@epfl.ch>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds the Alarm support, this mode enabled when adding
IORESOURCE_IRQ to the platform device resources.
The patch also enables the wakeup mode, so the wakealarm sysfs file (under
/sys/class/rtc/rtcX/) can be used to configure the alarm clock.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Nicolas Pitre <nico@marvell.com>
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add setting and clearing of the "pending" flag of the RTC alarm. The
semantics follow the UEFI specification 2.2 available at
http://www.uefi.org/specs/, i.e., the "pending" flag is cleared by
disabling the alarm, but not by any other condition (such as the passing
of time, a successful wakeup, or setting of a new alarm.)
Signed-off-by: Werner Almesberger <werner@openmoko.org>
Signed-off-by: Paul Fertser <fercerpav@gmail.com>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: Paul Gortmaker <p_gortmaker@yahoo.com>
Cc: Balaji Rao <balajirrao@openmoko.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The to_platform_device macro itself uses container_of macro. Nested use
of container_of macro causes following sparse warnings:
rtc-ds1553.c:259:3: warning: symbol '__mptr' shadows an earlier one
rtc-ds1553.c:259:3: originally declared here
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Call dev_set_drvdata before rtc device creation.
- Use its own spinlock instead of rtc->irq_lock. Because pdata->rtc
must be initialized to use the irq_lock (pdata->rtc->irq_lock). There
is a small window which rtc methods can be called before pdata->rtc is
initialized.
And there is no need use the irq_lock to protect hardware registers.
The driver's own spinlock shoule be enough.
- Check pdata->rtc before calling rtc_update_irq.
- Use alarm_irq_enable and remove ioctl routine.
- Use devres APIs and simplify error/remove path.
These fixes are ported from ds1553 driver and just compile-tested only.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alessandro Zummo <alessandro.zummo@towertech.it>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Call dev_set_drvdata before rtc device creation
* Use its own spinlock instead of rtc->irq_lock
* Check pdata->rtc before calling rtc_update_irq
* Use {alarm,update}_irq_enable and remove ioctl routine
* Use devres APIs and simplify error/remove path
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* Use its own spinlock instead of rtc->irq_lock
* Check pdata->rtc before calling rtc_update_irq
* Disable interrupt after rtc_device_unregister
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Acked-by: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
- Call dev_set_drvdata before rtc device creation.
- Use its own spinlock instead of rtc->irq_lock. Because pdata->rtc
must be initialized to use the irq_lock (pdata->rtc->irq_lock). There
is a small window which rtc methods can be called before pdata->rtc is
initialized.
And there is no need use the irq_lock to protect hardware registers.
The driver's own spinlock shoule be enough.
- Check pdata->rtc before calling rtc_update_irq.
- Use {alarm,update}_irq_enable and remove ioctl routine.
- Use devres APIs and simplify error/remove path.
These fixes are ported from ds1553 driver and just compile-tested only.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andrew Sharp <andy.sharp@lsi.com>
Cc: Thomas Hommel <thomas.hommel@gefanuc.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Drop ioctl function that handles RTC_AIE/RTC_UIE, and use instead the
rtc subsystem API (alarm_irq_enable/update_irq_enable callbacks).
Signed-off-by: Herton Ronaldo Krzesinski <herton@mandriva.com.br>
Cc: Alessandro Zummo <a.zummo@towertech.it>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Herton Ronaldo Krzesinski recently raised up, and fixed, an issue with the
rtc_cmos driver, which was referring to an inconsistent driver data.
This patch ensures that driver data registration happens before
rtc_device_register().
Signed-off-by: Alessandro Zummo <a.zummo@towertech.it>
Acked-by: Thomas Hommel <thomas.hommel@gefanuc.com>
Acked-by: Hans-Christian Egtvedt <hcegtvedt@atmel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: David S. Miller <davem@davemloft.net>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Andrew Sharp <andy.sharp@onstor.com>
Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Alexander Bigga <ab@mycable.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: Mark Zhan <rongkai.zhan@windriver.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I noticed that rtc wont generate interrupts after a resume from disk.
Here hpet rtc emulation is used.
Problem is that rtc hpet comparator, isn't reinitialized after resume.
Easiest way to solve this, is always mask all hpet interrupts on suspend
This is triggered, when suspending with alarm set.
Otherwise, hpet driver will think it doesn't need to reinitialize
the rtc comparator, thus rtc interrupts won't work.
This emulation isn't need for wakealarm.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch adds support for RTC in phoenix TWL6030.
Register offset addresses have changed in TWL6030
rtc-twl.c will hence forth support all twl RTC (4030, 5030, 6030 ..)
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames all twl4030_ functions to twl_ so that RTC driver can be
shared between Triton and Phoenix.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Nayak Rajendra <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch renames function names like twl4030_i2c_write_u8,
twl4030_i2c_read_u8 to twl_i2c_write_u8, twl_i2c_read_u8
and also common variable in twl-core.c
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The upcoming TWL6030 is companion chip for OMAP4 like the current TWL4030
for OMAP3. The common modules like RTC, Regulator creates opportunity
to re-use the most of the code from twl4030.
This patch renames few common drivers twl4030* files to twl* to enable
the code re-use.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
