Several changes at register stuff were done since commit
b45009b028, but I've forgot
to add the copyright line for this. Those changes allowed
cx88 to have multiple tuners, allowing it to support hardware with
separated radio and video tuners. It also allows binding a tuner to an
specific i2c address.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88-alsa can be compiled in (in distro built kernels, for example), but
not used. In those cases, the audio DMA restart is needed for proper sound
on NICAM channels.
This patch enables the DMA restart even with ALSA, but the functions now
check if cx88-alsa is really active.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
If the FX2 does not reset properly during reboot, it can present an
invalid USB device ID and fail to attach. Prevent this situation
from occuring by resetting the USB part of the card when the PCI part
probes.
Also fix the GPIO configurations so that analog capture will not
inadvertantly reset the USB part.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
1) It sets LNBDCPol differently based on the card type. Now it should
work properly for both the kworld and geniatech cards.
2) It stops returning an error for the SEC_VOLTAGE_OFF voltage command
(the cx88-dvb level handles the actual voltage on/off, but it still
passes the ioctl down to the cx24123 level, which previously rejected
the OFF as invalid so the ioctl would report failure)
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Yeasah Pell <yeasah@schwide.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch cleans up some whitespace problems after the dvb_attach changes
in cx88-dvb.c and saa7134-dvb.c, and converts some capitalized i2c address
constants to lowercase.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
The test in dvb-pll to see if a tuner's PLL responds when attaching fails
on NXT2004 based boards before the firmware is loaded.
This patch allows us to avoid this test by not passing an I2C bus handle to
the dvb_pll_attach routine, just as Chris Pascoe has done for MT352 and
ZL10353 based boards when used in cx88-dvb.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Typical wiring of MT352 and ZL10353 based tuners differs from dvb-pll's
expectation that the PLL is directly accessible. On these boards, the
PLL is actually hidden behind the demodulator, and as such can only be
accessed via the demodulator's interface. It was failing to communicate
with the PLL during an attach test and subsequently not connecting the
tuner ops.
By passing a NULL I2C bus handle to dvb_pll_attach, this accessibility
check can be bypassed. Do this for the affected boards. Also fix a
possible NULL dereference at sleep time, which would otherwise be
exposed by this change.
Signed-off-by: Chris Pascoe <c.pascoe@itee.uq.edu.au>
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Allow it to be en/disabled
Disable it in < 2.6.17 due to symbol_xxx() bug
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Only devices using > 1 frontend were ported; ones which did not are left
using static binding.
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Acked-by: Michael Krufky <mkrufky@linuxtv.org>
Acked-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for Shenzhen Tungsten Ages Tech TE-DTV-250 OEM for
Swann PCI TV Tuner Card
Signed-off-by: David Bussenschutt <buzz@oska.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for Norwood PCI TV Tuner (non-pro)
Signed-off-by: Peter Naulls <peter@chocky.org>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds autodetection support for the AverMedia M150-D
blackbird MPEG encoder / analog video capture card.
This board is known to work with the ASUS PVR 416 configuration.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
add initial support for Hauppauge WinTV-HVR3000 TriMode Analog/DVB-S/DVB-T
only analog is working for now
Signed-off-by: Eric Thomas <ethomas@claranet.fr>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Since kernel include autoconf.h via command line, those config.h inclusion
can be removed.
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Several DVB modules depends on I2C
Signed-off-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
A patch from Aug, 17 activated by mistake OVERLAY flag on cx88-video,
together with several cx88-blackbird cleanups. This makes the cx88 driver
to report:
/dev/video0 [v4l2]: ioctl VIDIOC_G_FBUF: Invalid argument
instead of:
/dev/video0 [v4l2]: no overlay support
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed usage of HAVE_V4L1
Including videodev.h will just include videodev2.h if V4L1 is not supported
V4L1 code at core drivers will honor CONFIG_V4L1_COMPAT stuff
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Fix keycode calculations (all codes for this remote were wrong due to a
lost + sign)
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Use release_firmware() to free requested resources.
According to Documentation/firmware_class/README the request_firmware()
call should be followed by a release_firmware(). Some drivers do not
however free the firmware previously allocated with request_firmware().
This patch tries to fix this by making sure that release_firmware() is used
as expected.
Signed-off-by: Magnus Damm <magnus@valinux.co.jp>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds support for the Geniatech Digistar, aka
Digiwave 103g DVB-S card.
Acked-by: Andrew de Quincey <adq_dvb@lidskialf.net>
Signed-off-by: Saqeb Akhter <johoja@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
We should no longer try to load the tda9887 module, because it no longer
exists. The tda9887 driver has been merged into the tuner module.
This patch removes all instances of request_module("tda9887") from
the following video4linux drivers: bttv, cx88, em28xx and saa7134.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch implements the newer v4l2 control features to make the
standard user controls and mpeg encoder controls of cx88-blackbird
video encoder boards available to userspace.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6:
[PATCH] i386: export memory more than 4G through /proc/iomem
[PATCH] 64bit Resource: finally enable 64bit resource sizes
[PATCH] 64bit Resource: convert a few remaining drivers to use resource_size_t where needed
[PATCH] 64bit resource: change pnp core to use resource_size_t
[PATCH] 64bit resource: change pci core and arch code to use resource_size_t
[PATCH] 64bit resource: change resource core to use resource_size_t
[PATCH] 64bit resource: introduce resource_size_t for the start and end of struct resource
[PATCH] 64bit resource: fix up printks for resources in misc drivers
[PATCH] 64bit resource: fix up printks for resources in arch and core code
[PATCH] 64bit resource: fix up printks for resources in pcmcia drivers
[PATCH] 64bit resource: fix up printks for resources in video drivers
[PATCH] 64bit resource: fix up printks for resources in ide drivers
[PATCH] 64bit resource: fix up printks for resources in mtd drivers
[PATCH] 64bit resource: fix up printks for resources in pci core and hotplug drivers
[PATCH] 64bit resource: fix up printks for resources in networks drivers
[PATCH] 64bit resource: fix up printks for resources in sound drivers
[PATCH] 64bit resource: C99 changes for struct resource declarations
Fixed up trivial conflict in drivers/ide/pci/cmd64x.c (the printk that
was changed by the 64-bit resources had been deleted in the meantime ;)
This is needed if we wish to change the size of the resource structures.
Based on an original patch from Vivek Goyal <vgoyal@in.ibm.com>
Cc: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A card number is not unique enough. Instead, let the caller specify the
prefix of the status messages.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
implemented VIDIOC_LOG_STATUS in the cx88-blackbird driver
to show the status of i2c clients and the cx23416 mpeg encoder.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
* master.kernel.org:/pub/scm/linux/kernel/git/mchehab/v4l-dvb:
V4L/DVB (4227): Update this driver for recent header file movement.
V4L/DVB (4223): Add V4L2_CID_MPEG_STREAM_VBI_FMT control
V4L/DVB (4222): Always switch tuner mode when calling VIDIOC_S_FREQUENCY.
V4L/DVB (4221): Add HM12 YUV format define.
V4L/DVB (4219): Av7110: analog sound output of DVB-C rev 2.3
V4L/DVB (4217): Fix a misplaced closing bracket/else, which caused swzigzag not to be called
V4L/DVB (4215): Make VIDEO_CX88_BLACKBIRD a separate build option
V4L/DVB (4214): Make VIDEO_CX2341X a selectable build option
V4L/DVB (4213): Cx88: cleanups
V4L/DVB (4211): Fix an Oops for all fe that have get_frontend_algo == NULL
This patch converts the combination of list_del(A) and list_add(A, B) to
list_move(A, B) under drivers/.
Acked-by: Corey Minyard <minyard@mvista.com>
Cc: Ben Collins <bcollins@debian.org>
Acked-by: Roland Dreier <rolandd@cisco.com>
Cc: Alasdair Kergon <dm-devel@redhat.com>
Cc: Gerd Knorr <kraxel@bytesex.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Frank Pavlic <fpavlic@de.ibm.com>
Acked-by: Matthew Wilcox <matthew@wil.cx>
Cc: Andrew Vasquez <linux-driver@qlogic.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Greg Kroah-Hartman <greg@kroah.com>
Signed-off-by: Akinobu Mita <mita@miraclelinux.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch creates a new Kconfig menu option, entitled,
"Blackbird MPEG encoder support (cx2388x + cx23416)"
so that the cx88-blackbird mpeg encoder module can be
chosen separately.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Removed the switch..case block in blackbird_probe for setting encoder height
based on video standard. All blackbird devices can rely on tvnorm->id to
retrieve this information from the cx2388x video decoder - tuner_formats
should not be used to determine the encoding video standard.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
CX2341X port was always set to 'memory', but 'streaming' is also possible
ivtv uses the memory (DMA) interface with the CX2341X, while pvrusb2 and
cx88-blackbird use the streaming interface. This setting is now selectable
by the driver.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Put old MPEGCOMP API under #if __KERNEL__ and issue warnings when used.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Adds the cx2341x.c module that handles the programming of the Conexant
cx23415/6 MPEG encoder chip used by cx88-blackbird, pvrusb2 and ivtv.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
clear EN_I2SIN_ENABLE bit for ASUS PVR-416 to enable audio
streaming in both raw video and blackbird mpeg encoder modes.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
Add support for FusionHDTV 3 Gold (original revision), using the
card definition for FusionHDTV3 Gold-Q
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There's a call at cx88-tvaudio to reset DMA sound on channel change; that
call was killing cx88-alsa whenever the channel was changed, resulting
in no sound. Remove those calls if cx88-alsa is selected to be compiled.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
cx88-alsa was resetting the card on load, causing the IRQ IR handler
to go away (maybe others, too). There's no actual need to reset the
card, though, so that line was removed
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
There was an unmasked bit in the keycodes that was causing random
behaviour (the code could be N or N+1). Masked that bit now.
Signed-off-by: Ricardo Cerqueira <v4l@cerqueira.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch splits up dvb_pll_attach and isl6421_attach function calls
such that the lines do not exceed 80 columns. This patch is purely cosmetic,
with no functional change at all.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
- moved CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_DUAL frontend_attach code up
to share the #ifdef block with CX88_BOARD_DVICO_FUSIONHDTV_DVB_T_PLUS
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
This patch adds support for a newer version of this device
using the zl10353 frontend instead of the mt352 frontend.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@infradead.org>
