Remove acpi_hw_write_gpe_enable_reg, it had been reduced down to a
single line of code, and called from only one place.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Rename acpi_hw_gpe_register_bit to acpi_hw_get_gpe_register_bit
in order to be same with ACPICA code base.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
ACPICA uses acpi_ev_enable_gpe() for enabling GPEs at the low level,
which is incorrect, because this function only enables the GPE if the
corresponding bit in its enable register's enable_for_run mask is set.
This causes acpi_set_gpe() to work incorrectly if used for enabling
GPEs that were not previously enabled with acpi_enable_gpe(). As a
result, among other things, wakeup-only GPEs are never enabled by
acpi_enable_wakeup_device(), so the devices that use them are unable
to wake up the system.
To fix this issue remove acpi_ev_enable_gpe() and its counterpart
acpi_ev_disable_gpe() and replace acpi_hw_low_disable_gpe() with
acpi_hw_low_set_gpe() that will be used instead to manipulate GPE
enable bits at the low level. Make the users of acpi_ev_enable_gpe()
and acpi_ev_disable_gpe() call acpi_hw_low_set_gpe() instead and
make sure that GPE enable masks are only updated by acpi_enable_gpe()
and acpi_disable_gpe() when GPE reference counters change from 0
to 1 and from 1 to 0, respectively.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
In quite a few places ACPICA needs to compute a GPE enable mask with
only one bit, corresponding to a given GPE, set. Currently, that
computation is always open coded which leads to unnecessary code
duplication. Fix this by introducing a helper function for computing
one-bit GPE enable masks and using it where appropriate.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Len Brown <len.brown@intel.com>
Add 2010 copyright to all module headers and signons, including
the Linux header. This affects virtually every file in the ACPICA
core subsystem, iASL compiler, and all utilities.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Needed by drivers for new ACPi tables. Internal versions of
these functions still use 32-bit max transfers, in order to
minimize disruption and stack use for the standard ACPI registers
(FADT-based).
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Protect certain I/O ports from reads/writes. Provides MS
compatibility. New module, hwvalid.c
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Added acpi_hw_write_pm1_control. This function writes both of the PM1
control registers (A/B). These registers are different than than
the PM1 A/B status and enable registers in that different values
can be written to the A/B registers. Most notably, the SLP_TYP
bits can be different, as per the values returned from the _Sx
predefined methods.
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
