Make hibernation messages start with one common prefix "PM: " and use
the word "hibernation" in the messages as a synonym of "suspend to
disk".
Turn some KERN_INFO messages into debug ones.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
Remove the unnecessary extern declaration of resume_file[]
from kernel/power/swap.c .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Len Brown <len.brown@intel.com>
At least on some machines it is necessary to prepare the ACPI firmware for the
restoration of the system memory state from the hibernation image if the
"platform" mode of hibernation has been used. Namely, in that cases we need
to disable the GPEs before replacing the "boot" kernel with the "frozen"
kernel (cf. http://bugzilla.kernel.org/show_bug.cgi?id=7887). After the
restore they will be re-enabled by hibernation_ops->finish(), but if the
restore fails, they have to be re-enabled by the restore code explicitly.
For this purpose we can introduce two additional hibernation operations,
called pre_restore() and restore_cleanup() and call them from the restore code
path. Still, they should be called if the "platform" mode of hibernation has
been used, so we need to pass the information about the hibernation mode from
the "frozen" kernel to the "boot" kernel in the image header.
Apparently, we can't drop the disabling of GPEs before the restore because of
Bug #7887 . We also can't do it unconditionally, because the GPEs wouldn't
have been enabled after a successful restore if the suspend had been done in
the 'shutdown' or 'reboot' mode.
In principle we could (and probably should) unconditionally disable the GPEs
before each snapshot creation *and* before the restore, but then we'd have to
unconditionally enable them after the snapshot creation as well as after the
restore (or restore failure) Still, for this purpose we'd need to modify
acpi_enter_sleep_state_prep() and acpi_leave_sleep_state() and we'd have to
introduce some mechanism synchronizing the disablind/enabling of the GPEs with
the device drivers' .suspend()/.resume() routines and with
disable_/enable_nonboot_cpus(). However, this would have affected the
suspend (ie. s2ram) code as well as the hibernation, which I'd like to avoid
in this patch series.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix sizeof(PAGE_SIZE) typo. It should be just PAGE_SIZE for zeroing the
swsusp_header.
Signed-off-by: OGAWA Hirofumi <hogawa@miraclelinux.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Remove includes of <linux/smp_lock.h> where it is not used/needed.
Suggested by Al Viro.
Builds cleanly on x86_64, i386, alpha, ia64, powerpc, sparc,
sparc64, and arm (all 59 defconfigs).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Make swsusp use extents instead of a bitmap to trace swap pages allocated
for saving the image (the tracking is only needed in case there's an error,
so that the allocated swap pages can be released).
This should allow us to reduce the memory usage, practically always, and
improve performance.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Nigel Cunningham <nigel@nigel.suspend2.net>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
o virt_to_page() call should be used on kernel linear addresses and not
on kernel text and data addresses. Swsusp code uses it on kernel data
(statically allocated swsusp_header).
o Allocate swsusp_header dynamically so that virt_to_page() can be used
safely.
o I am changing this because in next few patches, __pa() on x86_64 will
no longer support kernel text and data addresses and hibernation breaks.
Signed-off-by: Vivek Goyal <vgoyal@in.ibm.com>
Signed-off-by: Andi Kleen <ak@suse.de>
In the kernels later than 2.6.19 there is a regression that makes swsusp
fail if the resume device is not explicitly specified.
It can be fixed by adding an additional parameter to
mm/swapfile.c:swap_type_of() allowing us to pass the (struct block_device
*) corresponding to the first available swap back to the caller.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move all labels in the swsusp code to the second column, so that they won't
fool diff -p.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp measure and print the time needed to shrink memory during the
suspend.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Nigel Cunningham <nigel@suspend2.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
swsusp uses GFP_ATOMIC, but it can afford to use __GFP_WAIT, which will
permit it to reclaim clean pagecache instead of emitting scary
page-allocation-failure messages.
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently swsusp saves the contents of highmem pages by copying them to the
normal zone which is quite inefficient (eg. it requires two normal pages
to be used for saving one highmem page). This may be improved by using
highmem for saving the contents of saveable highmem pages.
Namely, during the suspend phase of the suspend-resume cycle we try to
allocate as many free highmem pages as there are saveable highmem pages.
If there are not enough highmem image pages to store the contents of all of
the saveable highmem pages, some of them will be stored in the "normal"
memory. Next, we allocate as many free "normal" pages as needed to store
the (remaining) image data. We use a memory bitmap to mark the allocated
free pages (ie. highmem as well as "normal" image pages).
Now, we use another memory bitmap to mark all of the saveable pages
(highmem as well as "normal") and the contents of the saveable pages are
copied into the image pages. Then, the second bitmap is used to save the
pfns corresponding to the saveable pages and the first one is used to save
their data.
During the resume phase the pfns of the pages that were saveable during the
suspend are loaded from the image and used to mark the "unsafe" page
frames. Next, we try to allocate as many free highmem page frames as to
load all of the image data that had been in the highmem before the suspend
and we allocate so many free "normal" page frames that the total number of
allocated free pages (highmem and "normal") is equal to the size of the
image. While doing this we have to make sure that there will be some extra
free "normal" and "safe" page frames for two lists of PBEs constructed
later.
Now, the image data are loaded, if possible, into their "original" page
frames. The image data that cannot be written into their "original" page
frames are loaded into "safe" page frames and their "original" kernel
virtual addresses, as well as the addresses of the "safe" pages containing
their copies, are stored in one of two lists of PBEs.
One list of PBEs is for the copies of "normal" suspend pages (ie. "normal"
pages that were saveable during the suspend) and it is used in the same way
as previously (ie. by the architecture-dependent parts of swsusp). The
other list of PBEs is for the copies of highmem suspend pages. The pages
in this list are restored (in a reversible way) right before the
arch-dependent code is called.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add the kernel command line parameter "resume_offset=" allowing us to specify
the offset, in <PAGE_SIZE> units, from the beginning of the partition pointed
to by the "resume=" parameter at which the swap header is located.
This offset can be determined, for example, by an application using the FIBMAP
ioctl to obtain the swap header's block number for given file.
[akpm@osdl.org: we don't know what type sector_t is]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp use block device offsets instead of swap offsets to identify swap
locations and make it use the same code paths for writing as well as for
reading data.
This allows us to use the same code for handling swap files and swap
partitions and to simplify the code, eg. by dropping rw_swap_page_sync().
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Rearrange the code in kernel/power/swap.c so that the next patch is more
readable.
[This patch only moves the existing code.]
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The Linux kernel handles swap files almost in the same way as it handles swap
partitions and there are only two differences between these two types of swap
areas:
(1) swap files need not be contiguous,
(2) the header of a swap file is not in the first block of the partition
that holds it. From the swsusp's point of view (1) is not a problem,
because it is already taken care of by the swap-handling code, but (2) has
to be taken into consideration.
In principle the location of a swap file's header may be determined with the
help of appropriate filesystem driver. Unfortunately, however, it requires
the filesystem holding the swap file to be mounted, and if this filesystem is
journaled, it cannot be mounted during a resume from disk. For this reason we
need some other means by which swap areas can be identified.
For example, to identify a swap area we can use the partition that holds the
area and the offset from the beginning of this partition at which the swap
header is located.
The following patch allows swsusp to identify swap areas this way. It changes
swap_type_of() so that it takes an additional argument representing an offset
of the swap header within the partition represented by its first argument.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
My fancy new swsusp IO code had a big memory leak. It's somewhat invisible
because the whole mem_map[] gets overwritten after resume, but it can cause us
to get low on memory during the actual suspend process.
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make swsusp use memory bitmaps to store its internal information during the
resume phase of the suspend-resume cycle.
If the pfns of saveable pages are saved during the suspend phase instead of
the kernel virtual addresses of these pages, we can use them during the resume
phase directly to set the corresponding bits in a memory bitmap. Then, this
bitmap is used to mark the page frames corresponding to the pages that were
saveable before the suspend (aka "unsafe" page frames).
Next, we allocate as many page frames as needed to store the entire suspend
image and make sure that there will be some extra free "safe" page frames for
the list of PBEs constructed later. Subsequently, the image is loaded and, if
possible, the data loaded from it are written into their "original" page
frames (ie. the ones they had occupied before the suspend).
The image data that cannot be written into their "original" page frames are
loaded into "safe" page frames and their "original" kernel virtual addresses,
as well as the addresses of the "safe" pages containing their copies, are
stored in a list of PBEs. Finally, the list of PBEs is used to copy the
remaining image data into their "original" page frames (this is done
atomically, by the architecture-dependent parts of swsusp).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Implement async reads for swsusp resuming.
Crufty old PIII testbox:
15.7 MB/s -> 20.3 MB/s
Sony Vaio:
14.6 MB/s -> 33.3 MB/s
I didn't implement the post-resume bio_set_pages_dirty(). I don't really
understand why resume needs to run set_page_dirty() against these pages.
It might be a worry that this code modifies PG_Uptodate, PG_Error and
PG_Locked against the image pages. Can this possibly affect the resumed-into
kernel? Hopefully not, if we're atomically restoring its mem_map?
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Jens Axboe <axboe@suse.de>
Cc: Laurent Riffard <laurent.riffard@free.fr>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some instrumentation to the swsusp readin code to show what bandwidth
we're achieving.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Switch the swsusp writeout code from 4k-at-a-time to 4MB-at-a-time.
Crufty old PIII testbox:
12.9 MB/s -> 20.9 MB/s
Sony Vaio:
14.7 MB/s -> 26.5 MB/s
The implementation is crude. A better one would use larger BIOs, but wouldn't
gain any performance.
The memcpys will be mostly pipelined with the IO and basically come for free.
The ENOMEM path has not been tested. It should be.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Add some instrumentation to the swsusp writeout code to show what bandwidth
we're achieving.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Do not panic a machine when swsusp signature can't be read.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
kernel/power/swap.c: In function 'swsusp_write':
kernel/power/swap.c:275: warning: 'start' may be used uninitialized in this function
gcc isn't smart enough, so help it.
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
If there's an error in load_image() we should return that without checking
snapshot_image_loaded.
Signed-off-by: Con Kolivas <kernel@kolivas.org>
Acked-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the swap-writing/reading code of swsusp to a separate file.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
