the hdsp driver refuses to report any information via the proc
interface, if the io box is not connected. with this patch, the
content of the control and status registers is printed before the
iobox check.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow the use of the FIRMWARE_IN_KERNEL option with hdsp cards and
in-kernel driver.
Also corrected a typo in the comment.
Signed-off-by: Raphael Doursenaud <rdoursenaud@free.fr>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Ignore MIDI and PCM events in the interrupt handler until the device
gets initialized properly. Otherwise you may get kernel panic by the
access to uninitialized devices via hotplugging.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
sleeping for 2 seconds before checking for the iobox is not enough
on some systems.
this patch increases the timeout, but polls the card during that
time. it thus speeds up the module loading when the card has already
been initialized, while being more robust on systems, which require
a higher timeout than the predefined 2 seconds.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace all tasklet_hi_schedule() callers with the normal
tasklet_schedule(). The former often causes troubles with
RT-kernels, and has actually no merit.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The card->id (card text identification) can be changed at runtime.
It might be confusing to have old text identification in device name.
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
currently, the error message when trying to run hdspmixer or hdspconf
if the breakout box is not connected is somehow misleading, since it
asks the user to upload the firmware.
this patch adds a test, whether the breakout box is connected and
tries to upload the firmware in the case, that it is not present, e.g.
because of power failures of the breakout box.
[Minor coding-style fixes by tiwai]
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
currently the hdsp driver tries to upload the firmware, even if the
io box is not connected. this patch adds a check for the io box
before trying to upload the firmware.
thus instead of messages complaining about the fifo status and firmware
loading failure, the driver gives a message that no multiface or
digiface is connected.
[A minor coding-style fix by tiwai]
Signed-off-by: Tim Blechmann <tim@klingt.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Kill snd_assert() in sound/pci/*, either removed or replaced with
if () with snd_BUG_ON().
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
The bits indicating SPDIF frequency in the status register are not the same for
the 9632 than for the other cards, because it also supports 192kHz. A specific
bitmask has thus been added (used in hdsp_spdif_sample_rate()).
The 9632 does not seem to report external sample rates greater than 96kHz. In
this case, the best seems to report spdif rate when autosync reference is
spdif. This also required to move function hdsp_spdif_sample_rate().
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This device has io_type == 1 (Multiface) and firmware_rev > 0xa
(fixes regression from changeset 5326)
Signed-off-by: Andreas Degert <ad@papyrus-gmbh.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Fix section mismatch in hdsp: snd_hdsp_proc_init() can be called from
an ioctl at any time.
WARNING: vmlinux.o(.text+0x1089bc2): Section mismatch: reference to .init.text: (between 'snd_hdsp_create_alsa_devices' and 'snd_hdsp_free')
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
This header file exists only for some hacks to adapt alsa-driver
tree. It's useless for building in the kernel. Let's move a few
lines in it to sound/core.h and remove it.
With this patch, sound/driver.h isn't removed but has just a single
compile warning to include it. This should be really killed in
future.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Check the value ranges in ctl put callbacks properly in the rest of
PCI drivers.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
Remove duplicated defines.
(From their use it looks like 'midiDataOutx are written to
rather than read from.)
Signed-off-by: Nicolas Kaiser <nikai@nikai.net>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@perex.cz>
added support for the latest revision of the 9632 (and hopefully a few
following ones). The DSP matrix was not working because of wrong
identification of the card in this part of the code.
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Clean up codes using the new common snd_ctl_boolean_*_info() callbacks.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add 'DDS Sample Rate Offset' control. Allows values in Hz from -5000 to +5000.
The value is added to the nominal sample rate and written to the DDS register.
Signed-off-by: Julian Cable <julian_cable@yahoo.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added a new macro snd_pcm_group_for_each_entry() just for code cleanup.
Old macros, snd_pcm_group_for_each() and snd_pcm_group_substream_entry(),
are removed.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Add DDS register support for RME9632 rev >= 152.
This register sets the sample rate for these cards and is required
in addition to the standard control register. It corresponds to a
quartz divisor.
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Added the support for mixer matrix of RME9632 rev 152.
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fix IRQ flags for PCI devices.
The shared IRQs for PCI devices shouldn't be allocated with
IRQF_DISABLED. Also, when MSI is enabled, IRQF_SHARED shouldn't
be used.
The patch removes unnecessary cast in request_irq and free_irq,
too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
precise_ptr option causes dysfunction with hdsp driver.
Turn it off as default.
Signed-off-by: Remy Bruno <remy.bruno@trinnov.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Maintain a per-CPU global "struct pt_regs *" variable which can be used instead
of passing regs around manually through all ~1800 interrupt handlers in the
Linux kernel.
The regs pointer is used in few places, but it potentially costs both stack
space and code to pass it around. On the FRV arch, removing the regs parameter
from all the genirq function results in a 20% speed up of the IRQ exit path
(ie: from leaving timer_interrupt() to leaving do_IRQ()).
Where appropriate, an arch may override the generic storage facility and do
something different with the variable. On FRV, for instance, the address is
maintained in GR28 at all times inside the kernel as part of general exception
handling.
Having looked over the code, it appears that the parameter may be handed down
through up to twenty or so layers of functions. Consider a USB character
device attached to a USB hub, attached to a USB controller that posts its
interrupts through a cascaded auxiliary interrupt controller. A character
device driver may want to pass regs to the sysrq handler through the input
layer which adds another few layers of parameter passing.
I've build this code with allyesconfig for x86_64 and i386. I've runtested the
main part of the code on FRV and i386, though I can't test most of the drivers.
I've also done partial conversion for powerpc and MIPS - these at least compile
with minimal configurations.
This will affect all archs. Mostly the changes should be relatively easy.
Take do_IRQ(), store the regs pointer at the beginning, saving the old one:
struct pt_regs *old_regs = set_irq_regs(regs);
And put the old one back at the end:
set_irq_regs(old_regs);
Don't pass regs through to generic_handle_irq() or __do_IRQ().
In timer_interrupt(), this sort of change will be necessary:
- update_process_times(user_mode(regs));
- profile_tick(CPU_PROFILING, regs);
+ update_process_times(user_mode(get_irq_regs()));
+ profile_tick(CPU_PROFILING);
I'd like to move update_process_times()'s use of get_irq_regs() into itself,
except that i386, alone of the archs, uses something other than user_mode().
Some notes on the interrupt handling in the drivers:
(*) input_dev() is now gone entirely. The regs pointer is no longer stored in
the input_dev struct.
(*) finish_unlinks() in drivers/usb/host/ohci-q.c needs checking. It does
something different depending on whether it's been supplied with a regs
pointer or not.
(*) Various IRQ handler function pointers have been moved to type
irq_handler_t.
Signed-Off-By: David Howells <dhowells@redhat.com>
(cherry picked from 1b16e7ac850969f38b375e511e3fa2f474a33867 commit)
Fixed the auto-updating of firmware if the breakout box was switched
off/on. The firmware binary itself was already cached but it wasn't
loaded properly. Also, request_firmware() is issued if the box was
with firmware at module loading time but later it's erased.
The auto-update is triggered at each PCM action (open, prepare, etc)
and at opening proc files.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
Fixed 'section mismatch' errors in ALSA PCI drivers:
- removed invalid __devinitdata from pci id tables
- fix/remove __devinit of functions called in suspend/resume
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Jaroslav Kysela <perex@suse.cz>
RME HDSP driver
When using the kernel firmware loader, initialize the card shortname
before registering the card with ALSA to prevent it from using a
default card ID.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Digigram VX core,ENS1370/1+ driver,CA0106 driver,EMU10K1/EMU10K2 driver
RME HDSP driver,RME9652 driver
For consistency, use the PCM interface instead of MIXER for IEC958
default/mask/stream mixer controls.
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
