Patch from Sascha Hauer
This patch adds UCFR_RFDIV setting into i.MX serial driver.
This is required, if loader does not fully agree with Linux kernel
about UART setup manner. Linux only blindly expected some values until
now. This should enable to use even serial ports not recognized by
boot-loader as for example third UART found in the bluethoot module.
Patch also enables to detect original setup baudrate in more cases.
Signed-off-by: Pavel Pisa
Signed-off-by: Sascha Hauer
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In order to properly fix some issues with cpufreq vs. sleep on
PowerBooks, I had to add a suspend callback to the pmac_cpufreq driver.
I must force a switch to full speed before sleep and I switch back to
previous speed on resume.
I also added a driver flag to disable the warnings in suspend/resume
since it is expected in this case to have different speed (and I want it
to fixup the jiffies properly).
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
We were supporting 24bpp. However, the pixel organisation in
memory was 0RGB, so it was 24bpp in 32bit words. This means
we're actually supporting 32bpp and not 24bpp.
Also, add a check to ensure that we don't exceed the available
framebuffer when changing display resolutions.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
Call pci_enable_device() before looking at IRQ and resources,
and pci_disable_device() when shutting the interface down.
The driver requires this fix or the "pci=routeirq" workaround
on 2.6.10 and later kernels.
Reported and tested by Artur Lipowski.
From: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Marcelo Tosatti <marcelo.tosatti@cyclades.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
trivial iomem annotations + memset() replaced with memset_io() in a
place that deals with ioremapped area.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Convert 8250_hp300 to use serial8250_register_port() and
serial8250_unregister_port().
Tested by Kars de Jong, 4/4/2005.
Signed-off-by: Russell King <rmk@arm.linux.org.uk>
tg3_restart_ints() is called to re-enable interrupts after tg3_poll()
has finished all the work. It calls tg3_cond_int() to force an interrupt
if the status block updated bit is set. The updated bit will be set if
there is a new status block update sometime during tg3_poll() and it can
be very often. The worst part is that even if all the work has been
processed, the updated bit remains set and an interrupt will be forced
unnecessarily.
The fix is to call tg3_has_work() instead to determine if new work is
posted before forcing an interrupt. The way to force an interrupt is
also changed to use "coalesce_now" instead of "SETINT". The former is
generally a safer way to force the interrupt.
Also deleted the first parameter to tg3_has_work() which is unused.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch refreshes the hw rx producer in tg3_rx() so that additional
work posted by the hardware can be processed.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that causes tg3_has_work() to always return 1.
rx work is determined by comparing tp->rx_rcb_ptr with the current hw
producer index. The hw producer index is modulo the ring size, but tp-
>rx_rcb_ptr is a free running counter that goes up beyond the ring size.
After the ring wraps around once, tg3_has_work() will always return 1.
The fix is to always do modulo arithmetic on tp->rx_rcb_ptr.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following is an update of the patch I sent yesterday
(3/9/05) incorporating suggestions from Christoph Hellwig and
Andreas Schwab. It allows Altix and Altix-like systems to
handle environmental events generated by the system controllers,
and should apply on top of Jack Steiner's patch of 3/1/05 ("New
chipset support for SN platform") and Mark Goodwin's patch of
3/8/05 ("Altix SN topology support for new chipsets and pci
topology").
Signed-off-by: Greg Howard <ghoward@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch is to provide CX port infrastructure for SGI TIO-based
h/w. Also a 'core services' driver for SGI FPGA-based h/w.
Signed-off-by: Bruce Losure <blosure@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This enables the sun linux logo to be selected on sparc32.
Signed-off-by: Bob Breuer <breuerr@mc.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using the same logic as the other framebuffer fixes committed in 2.6.11,
this is a set of fixes to make TCX functional on the console again. Adds
the tcx_pan_display function, sets the
all->info.var.{red,green,blue}.length values to 8, and runs fb_set_cmap.
Also looks for the correct SUNW,tcx prom value.
This patch just slipped through the cracks.
Originally by: Georg Chini <georg.chini@triaton-webhosting.com>
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Minor cleanups for sparc specific drivers (sunbmac, sunqe, sunlance,
sunhme, esp) so that they have a full module version definition that is
consistent with other upstream drivers.
Signed-off-by: Tom 'spot' Callaway <tcallawa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
From: Panagiotis Issaris <takis@lumumba.luc.ac.be>
In the ENI155P device driver in six possible failure cases the requested
irq is not being released.
In three of the above possible failure cases additionally there seems to
be a memory leak.
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch>
Signed-off-by: Domen Puncer <domen@coderock.org>
Signed-off-by: Chas Williams <chas@cmf.nrl.navy.mil>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing the open coded equivalents and making ax25 look more like
a linux network protocol, i.e. more similar to inet.
Signed-off-by: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
void * __iomem foo is not a pointer to iomem - it's an iomem variable
containing void *. A pile of such guys in arch/sparc64/kernel/time.c,
drivers/sbus/char/rtc.c and include/asm-sparc64/mostek.h turned into
intended void __iomem *.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
(!ARCH_S390 && !M68K && !IA64 && !UML) is obviously always true on ARM.
Intended behaviour for ARM is "absent unless we are on RiscPC or
EBSA285". So what we want is added && !ARM in the first term - without
it the last part (|| ARCH_RPC || ARCH_EBSA285, that is) doesn't do
anything.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Missing include, breaks at least on arm.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
All boards dealt with by I2C_MPC are 32bit. Moreover, driver simply
won't build on ppc64 - it uses ppc32-only types all over the place.
Dependency fixed - it's PPC32, not PPC.
Signed-off-by: Al Viro <viro@parcelfarce.linux.theplanet.co.uk>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
